U-Boot SPL 2014.01-09730-gb5bd4c9-dirty (Mar 27 2014 - 21:52:56)
Board: A13_JTABLET
DRAM: 512 MiB
CPU: 1008000000Hz, AXI/AHB/APB: 3/2/2


U-Boot 2014.01-09730-gb5bd4c9-dirty (Mar 27 2014 - 21:52:56) Allwinner Technolog
y

CPU:   Allwinner A13/A10s (SUN5I)
Board: A13_JTABLET
I2C:   ready
DRAM:  512 MiB
MMC:   SUNXI SD/MMC: 0
*** Warning - bad CRC, using default environment

In:    serial
Out:   serial
Err:   serial
Hit any key to stop autoboot:  0
## Error inserting "stdout" variable, errno=22

## Checking Image at 41000000 ...
   Legacy image found
   Image Name:
   Image Type:   ARM Linux Script (gzip compressed)
   Data Size:    129 Bytes = 129 Bytes
   Load Address: 00000000
   Entry Point:  00000000
   Contents:
      Image 0: 121 Bytes = 121 Bytes
   Verifying Checksum ... OK
## Executing script at 41000000
## Booting kernel from Legacy Image at 52000000 ...
   Image Name:
   Image Type:   ARM Linux Kernel Image (uncompressed)
   Data Size:    5431888 Bytes = 5.2 MiB
   Load Address: 40008000
   Entry Point:  40008000
   Verifying Checksum ... OK
   Loading Kernel Image ... OK

Starting kernel ...

<6>Booting Linux on physical CPU 0
<6>Initializing cgroup subsys cpuset
<5>Linux version 3.4.79peterbjornx-00001-g8ea347b (jolanda_u@JOLANDA-UBUNTU) (gc
c version 4.7.1 (Ubuntu/Linaro 4.7.1-5ubuntu1~ppa1) ) #10 PREEMPT Thu Mar 27 20:
50:14 CET 2014
CPU: ARMv7 Processor [413fc082] revision 2 (ARMv7), cr=10c5387d
CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
Machine: sun5i
<6>Memory Reserved:
<6>     SYS  : 0x43000000 - 0x4300ffff  (  64 kB)
<6>     LCD  : 0x50000000 - 0x51ffffff  (  32 MB)
<6>cma: CMA: reserved 192 MiB at 43c00000
Memory policy: ECC disabled, Data cache writeback
<6>sunxi: Allwinner A13 revision B (AW1625/sun5i) detected.
<7>On node 0 totalpages: 114688
<7>free_area_init_node: node 0, pgdat c0a327b0, node_mem_map d2000000
<7>  DMA zone: 512 pages used for memmap
<7>  DMA zone: 0 pages reserved
<7>  DMA zone: 65024 pages, LIFO batch:15
<7>  Normal zone: 384 pages used for memmap
<7>  Normal zone: 48768 pages, LIFO batch:15
<7>pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768<c>
<7>pcpu-alloc: <c>[0] <c>0 <c>
Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 113792
<5>Kernel command line: mem=448M@0x40000000 console=ttyS0,115200 console=tty0 ro
ot=/dev/nandd panic=0 rootwait
<6>PID hash table entries: 2048 (order: 1, 8192 bytes)
<6>Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
<6>Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
<6>Memory: 448MB = 448MB total
<5>Memory: 213448k/213448k available, 245304k reserved, 0K highmem
<5>Virtual kernel memory layout:
    vector  : 0xffff0000 - 0xffff1000   (   4 kB)
    fixmap  : 0xfff00000 - 0xfffe0000   ( 896 kB)
    vmalloc : 0xdc800000 - 0xff000000   ( 552 MB)
    lowmem  : 0xc0000000 - 0xdc000000   ( 448 MB)
    pkmap   : 0xbfe00000 - 0xc0000000   (   2 MB)
    modules : 0xbf000000 - 0xbfe00000   (  14 MB)
      .text : 0xc0008000 - 0xc0999174   (9797 kB)
      .init : 0xc099a000 - 0xc09c9000   ( 188 kB)
      .data : 0xc09ca000 - 0xc0a390e8   ( 445 kB)
       .bss : 0xc0a3910c - 0xc0b2d930   ( 979 kB)
<6>SLUB: Genslabs=11, HWalign=64, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
<6>NR_IRQS:128
<6>sched_clock: 32 bits at 24MHz, resolution 41ns, wraps every 178956ms
<6>Console: colour dummy device 80x30
<6>console [tty0] enabled
<6>Calibrating delay loop... <c>1001.88 BogoMIPS (lpj=5009408)
<6>pid_max: default: 32768 minimum: 301
<6>Mount-cache hash table entries: 512
<6>Initializing cgroup subsys cpuacct
<6>Initializing cgroup subsys devices
<6>Initializing cgroup subsys freezer
<6>Initializing cgroup subsys blkio
<6>CPU: Testing write buffer coherency: ok
<6>hw perfevents: enabled with ARMv7 Cortex-A8 PMU driver, 5 counters available
<6>Setting up static identity map for 0x406f4238 - 0x406f426c
<6>devtmpfs: initialized
<6>dummy:
<6>NET: Registered protocol family 16
<6>DMA: preallocated 256 KiB pool for atomic coherent allocations
<6>hw-breakpoint: debug architecture 0x4 unsupported.
<6>Init eGon pin module V2.0
SOFTWINNER DMA Driver, (c) 2003-2004,2006 Simtec Electronics
<6>Initialize DMAC OK
<6>bio: create slab <bio-0> at 0
<5>SCSI subsystem initialized
<6>usbcore: registered new interface driver usbfs
<6>usbcore: registered new interface driver hub
<6>usbcore: registered new device driver usb
<6>Advanced Linux Sound Architecture Driver Version 1.0.25.
<6>cfg80211: Calling CRDA to update world regulatory domain
<6>Switching to clocksource aw_64bits_counter
<5>FS-Cache: Loaded
<6>CacheFiles: Loaded
[usb_manager]: CONFIG_USB_SW_SUNXI_USB0_HOST_ONLY
[sw_hcd0]: usb host driver initialize........
[sw_hcd0]: open_usb_clock
[sw_hcd0]: host_init_state = 1
[sw_hcd0]: platform is usb host
[sw_hcd0]: sw_hcd_host0: ConfigData=0xde (UTMI-8, dyn FIFOs, bulk combine, bulk
split, HB-ISO Rx (X), HB-ISO Tx (X), SoftConn)
[sw_hcd0]: sw_hcd_init_controller: sw_hcd_host0: USB Host mode controller at f1c
13000 using PIO, IRQ 38
<6>sw_hcd_host0 sw_hcd_host0: sw_hcd host driver
<6>sw_hcd_host0 sw_hcd_host0: new USB bus registered, assigned bus number 1
<6>hub 1-0:1.0: USB hub found
<6>hub 1-0:1.0: 1 port detected
is_on = 1, hcd0_set_vbus_cnt = 1
[sw_hcd_host0]: Set USB Power On

------------IRQ DISCONNECT-------------

<6>NET: Registered protocol family 2
<6>IP route cache hash table entries: 4096 (order: 2, 16384 bytes)
<6>TCP established hash table entries: 16384 (order: 5, 131072 bytes)
<6>TCP bind hash table entries: 16384 (order: 4, 65536 bytes)
<6>TCP: Hash tables configured (established 16384 bind 16384)
<6>TCP: reno registered
<6>UDP hash table entries: 256 (order: 0, 4096 bytes)
<6>UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
<6>NET: Registered protocol family 1
<6>RPC: Registered named UNIX socket transport module.
<6>RPC: Registered udp transport module.
<6>RPC: Registered tcp transport module.
<6>RPC: Registered tcp NFSv4.1 backchannel transport module.
<6>audit: initializing netlink socket (disabled)
<5>type=2000 audit(0.359:1): initialized
<5>VFS: Disk quotas dquot_6.5.2
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
<5>NFS: Registering the id_resolver key type
<6>NTFS driver 2.1.30 [Flags: R/W].
<6>fuse init (API version 7.18)
<6>JFS: nTxBlock = 3203, nTxLock = 25628
<6>SGI XFS with ACLs, security attributes, realtime, large block/inode numbers,
no debug enabled
<6>OCFS2 1.5.0
<6>ocfs2: Registered cluster interface o2cb
<6>OCFS2 DLMFS 1.5.0
OCFS2 User DLM kernel interface loaded
<6>OCFS2 Node Manager 1.5.0
<6>OCFS2 DLM 1.5.0
GFS2 installed
<6>msgmni has been set to 800
<3>alg: comp: Compression test 1 failed for lzo-generic: output len = 57
<6>alg: No test for stdrng (krng)
<6>Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253)
<6>io scheduler noop registered
<6>io scheduler deadline registered
<6>io scheduler cfq registered (default)
<6>sunxi disp driver loaded (/dev/disp api 1.0)
<6>Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
<3>[uart]: failed to get uart3's used information
<6>[uart]: used uart info.: 0x01
<6>[uart]: serial probe 0 irq 1 mapbase 0x01c28000
<6>sunxi-uart.0: ttyS0 at MMIO 0x1c28000 (irq = 1) is a U6_16550A
<6>console [ttyS0] enabled
<6>[drm] Initialized drm 1.1.0 20060810
<6>brd: module loaded
<6>loop: module loaded
[NAND] nand driver version: 0x2 0x9
<4>Dev Sunxi softw311 nand: part 1, start 32768, size 32768
<4>Dev Sunxi softw311 nand: part 2, start 65536, size 32768
<4>Dev Sunxi softw311 nand: part 3, start 98304, size 65536
<4>Dev Sunxi softw311 nand: part 4, start 163840, size 7569408
<6> nand: nanda nandb nandc nandd
[NAND]nand driver, ok.
[spi]: sw spi init !!
[spi]: sw spi init fetch spi0 uning configuration failed
[spi]: Get spi devices number failed
[spi]: register spi devices board info failed
<4>spi: cannot find any using configuration for                     all 4 spi co
ntrollers, return directly!
<4>emac_init fetch emac using configuration failed
<6>emac driver is disabled
<6>usbcore: registered new interface driver rtl8187
sw_usb_enable_hcd: usbc_num = 1
<6>usbcore: registered new interface driver rtl8188eu
<6>ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
<6>ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
<6>Initializing USB Mass Storage driver...
<6>usbcore: registered new interface driver usb-storage
<6>USB Mass Storage support registered.
<6>usbcore: registered new interface driver ums-alauda
<6>usbcore: registered new interface driver ums-cypress
<6>usbcore: registered new interface driver ums-datafab
<6>usbcore: registered new interface driver ums_eneub6250
<6>usbcore: registered new interface driver ums-freecom
<6>usbcore: registered new interface driver ums-isd200
<6>usbcore: registered new interface driver ums-jumpshot
<6>usbcore: registered new interface driver ums-karma
<6>usbcore: registered new interface driver ums-onetouch
<6>usbcore: registered new interface driver ums-realtek
<6>usbcore: registered new interface driver ums-sddr09
<6>usbcore: registered new interface driver ums-sddr55
<6>usbcore: registered new interface driver ums-usbat
<6>mousedev: PS/2 mouse device common for all mice
========RTC Inital ===================
rtc_fetch_sysconfig_para: after: rtc_twi_addr is 0x51, dirty_addr_buf: 0x51. dir
ty_addr_buf[1]: 0xfffe
rtc_fetch_sysconfig_para: rtc_twi_id is 1.
rtc_fetch_sysconfig_para:ok
pcf8563_init: after fetch_sysconfig_para:  normal_i2c: 0x51. normal_i2c[1]: 0xff
fe
<6>i2c /dev entries driver
config i2c gpio with gpio_config api
<6>axp_mfd 0-0034: AXP (CHIP ID: 0x41) detected
rtc_detect,line:157,twi_id:1,adapter->nr:0
rtc_detect,line:166
<6>I2C: i2c-0: AW16XX I2C adapter
rtc_detect,line:157,twi_id:1,adapter->nr:1
<6>rtc_detect: Detected chip pcf8563 at adapter 1, address 0x51
rtc_detect,line:162
pcf8563_probe,line:666
<6>pcf8563 1-0051: chip found, driver version 0.4.3
<6>pcf8563 1-0051: low voltage detected, date/time is not reliable.
pcf8563_get_datetime,raw data is st1=08, st2=80, sec=a5, min=c2, hr=99, mday=ac,
 wday=a6, mon=2f, year=fd
pcf8563_get_datetime: tm is secs=25, mins=42, hours=19,mday=32, mon=14, year=163
, wday=6
<3>pcf8563 1-0051: retrieved date/time is not valid.
<6>pcf8563 1-0051: rtc core: registered pcf8563 as rtc0
<6>I2C: i2c-1: AW16XX I2C adapter
rtc_detect,line:157,twi_id:1,adapter->nr:2
rtc_detect,line:166
<6>I2C: i2c-2: AW16XX I2C adapter
<6>lirc_dev: IR Remote Control driver registered, major 251
<6>IR NEC protocol handler initialized
<6>IR RC5(x) protocol handler initialized
<6>IR RC6 protocol handler initialized
<6>IR JVC protocol handler initialized
<6>IR Sony protocol handler initialized
<6>IR RC5 (streamzap) protocol handler initialized
<6>IR SANYO protocol handler initialized
<6>IR MCE Keyboard/mouse protocol handler initialized
<6>IR LIRC bridge handler initialized
[cedar dev]: install start!!!
[cedar dev]: install end!!!
[ace_drv] start!!!
[ace_drv] init end!!!
[pa_drv] start!!!
[pa_drv] init end!!!
<6>axp20_ldo1: 1300 mV
<6>axp20_ldo2: 1800 <--> 3300 mV at 3000 mV
<6>axp20_ldo3: 700 <--> 3500 mV at 3300 mV
<6>axp20_ldo4: 1250 <--> 3300 mV at 3300 mV
<6>axp20_buck2: 700 <--> 2275 mV at 1400 mV
<6>axp20_buck3: 700 <--> 3500 mV at 1200 mV
<6>axp20_ldoio0: 1800 <--> 3300 mV at 2800 mV
<6>input: axp20-supplyer as /devices/platform/sunxi-i2c.0/i2c-0/0-0034/axp20-sup
plyer.28/input/input0
<4>axp20_ldo2: Failed to create debugfs directory
<6>[mmc-msg] sw_mci_init
<6>[mmc-msg] MMC host used card: 0x1, boot card: 0x0, io_card 0
<6>[mmc-msg] sdc0 set round clock 400000, src 24000000
<6>[mmc-msg] sdc0 set ios: clk 0Hz bm OD pm OFF vdd 3.3V width 1 timing LEGACY(S
DR12) dt B
<6>[mmc-msg] sdc0 Probe: base:0xf1c0f000 irq:32 sg_cpu:c3c40000(43c40000) ret 0.

[mmc_pm]: no sdio card used in configuration
<6>sunxi_leds driver init
<6>sunxi leds can't find script data '[leds_para]' 'leds_used'
<6>usbcore: registered new interface driver usbhid
<6>usbhid: USB HID core driver
<6>IPv4 over IPv4 tunneling driver
<6>TCP: cubic registered
<6>Initializing XFRM netlink socket
<6>NET: Registered protocol family 17
<6>NET: Registered protocol family 15
<6>8021q: 802.1Q VLAN Support v1.8
<5>Registering the dns_resolver key type
<6>VFP support v0.3: implementor 41 architecture 3 part 30 variant c rev 3
<5>Registering SWP/SWPB emulation handler
<6>registered taskstats version 1
<6>[mmc-msg] mmc 0 detect change, present 1
<6>Console: switching to colour frame buffer device 100x30
<6>I2C: i2c-3: HDMI I2C adapter
<4>axp20_buck3: incomplete constraints, leaving on
<4>axp20_buck2: incomplete constraints, leaving on
<4>axp20_ldo4: incomplete constraints, leaving on
<4>axp20_ldo3: incomplete constraints, leaving on
<4>axp20_ldo2: incomplete constraints, leaving on
<4>axp20_ldo1: incomplete constraints, leaving on
<6>===========================ft5x_ts_init=====================
<6>ctp_fetch_sysconfig_para.
<3>ctp_fetch_sysconfig_para: name ekt3632 does not match CTP_NAME.
<3>ft5x_ts<6>ft5x_ts_init: err.
<6>pcf8563 1-0051: low voltage detected, date/time is not reliable.
pcf8563_get_datetime,raw data is st1=08, st2=80, sec=a7, min=c2, hr=99, mday=ac,
 wday=a6, mon=2f, year=fd
pcf8563_get_datetime: tm is secs=27, mins=42, hours=19,mday=32, mon=14, year=163
, wday=6
<3>pcf8563 1-0051: retrieved date/time is not valid.
<3>pcf8563 1-0051: hctosys: invalid date/time
<6>ALSA device list:
<6>  #0: sunxi-CODEC  Audio Codec
<6>[mmc-msg] sdc0 set ios: clk 0Hz bm PP pm UP vdd 3.3V width 1 timing LEGACY(SD
R12) dt B
<6>[mmc-msg] sdc0 power on
[ccmu] set sdc0 reset status to 0 failed!
<3>EXT3-fs (nandd): error: couldn't mount because of unsupported optional featur
es (240)
<3>[mmc-err] Failed to release sdc0 reset
<3>EXT2-fs (nandd): error: couldn't mount because of unsupported optional featur
es (244)
<6>[mmc-msg] sdc0 set ios: clk 400000Hz bm PP pm ON vdd 3.3V width 1 timing LEGA
CY(SDR12) dt B
<6>[mmc-msg] sdc0 set round clock 400000, src 24000000
<3>[mmc-err] smc 0 err, cmd 52,  RTO
<3>[mmc-err] smc 0 err, cmd 52,  RTO
<6>[mmc-msg] sdc0 set ios: clk 400000Hz bm PP pm ON vdd 3.3V width 1 timing LEGA
CY(SDR12) dt B
<6>[mmc-msg] sdc0 set ios: clk 400000Hz bm PP pm ON vdd 3.3V width 1 timing LEGA
CY(SDR12) dt B
<3>[mmc-err] smc 0 err, cmd 5,  RTO
<3>[mmc-err] smc 0 err, cmd 5,  RTO
<3>[mmc-err] smc 0 err, cmd 5,  RTO
<3>[mmc-err] smc 0 err, cmd 5,  RTO
<6>[mmc-msg] sdc0 set ios: clk 400000Hz bm PP pm ON vdd 3.3V width 1 timing LEGA
CY(SDR12) dt B
<6>[mmc-msg] sdc0 set ios: clk 400000Hz bm PP pm ON vdd 3.3V width 1 timing LEGA
CY(SDR12) dt B
<6>[mmc-msg] sdc0 set ios: clk 400000Hz bm PP pm ON vdd 3.3V width 1 timing LEGA
CY(SDR12) dt B
<6>[mmc-msg] sdc0 set ios: clk 400000Hz bm PP pm ON vdd 3.3V width 1 timing SD-H
S(SDR25) dt B
<6>[mmc-msg] sdc0 set ios: clk 50000000Hz bm PP pm ON vdd 3.3V width 1 timing SD
-HS(SDR25) dt B
<6>[mmc-msg] sdc0 set round clock 42857142, src 300000000
<6>[mmc-msg] sdc0 set ios: clk 50000000Hz bm PP pm ON vdd 3.3V width 4 timing SD
-HS(SDR25) dt B
<6>mmc0: new high speed SDHC card at address 1234
<6>mmcblk0: mmc0:1234 SA04G 3.67 GiB
<6> mmcblk0: p1
<6>EXT4-fs (nandd): recovery complete
<6>EXT4-fs (nandd): mounted filesystem with ordered data mode. Opts: (null)
<6>VFS: Mounted root (ext4 filesystem) on device 93:4.
<6>devtmpfs: mounted
<6>Freeing init memory: 188K
<30>systemd-udevd[179]: starting version 204