$ dmesg
8k reserved, 1152k data, 456k init, 1178120k highmem)
virtual kernel memory layout:
    fixmap  : 0xfff17000 - 0xfffff000   ( 928 kB)
    pkmap   : 0xff800000 - 0xffc00000   (4096 kB)
    vmalloc : 0xf7ffe000 - 0xff7fe000   ( 120 MB)
    lowmem  : 0xc0000000 - 0xf77fe000   ( 887 MB)
      .init : 0xc1437000 - 0xc14a9000   ( 456 kB)
      .data : 0xc13165ab - 0xc1436760   (1152 kB)
      .text : 0xc1000000 - 0xc13165ab   (3161 kB)
Checking if this processor honours the WP bit even in supervisor mode...Ok.
SLUB: Genslabs=15, HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
Preemptible hierarchical RCU implementation.
        Verbose stalled-CPUs detection is disabled.
NR_IRQS:2304 nr_irqs:712 16
CPU 0 irqstacks, hard=f6c0a000 soft=f6c0c000
Extended CMOS year: 2000
Console: colour VGA+ 80x25
console [tty1] enabled
hpet clockevent registered
Fast TSC calibration using PIT
Detected 1666.365 MHz processor.
Calibrating delay loop (skipped), value calculated using timer frequency.. 3332.73 BogoMIPS (lpj=1666365)
pid_max: default: 32768 minimum: 301
Mount-cache hash table entries: 512
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 0
mce: CPU supports 5 MCE banks
CPU0: Thermal monitoring enabled (TM2)
using mwait in idle threads.
ACPI: Core revision 20110623
Enabling APIC mode:  Flat.  Using 1 I/O APICs
..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1
CPU0: Intel(R) Atom(TM) CPU N570   @ 1.66GHz stepping 0a
Performance Events: PEBS fmt0+, Atom events, Intel PMU driver.
... version:                3
... bit width:              40
... generic registers:      2
... value mask:             000000ffffffffff
... max period:             000000007fffffff
... fixed-purpose events:   3
... event mask:             0000000700000003
CPU 1 irqstacks, hard=f6c82000 soft=f6c84000
Booting Node   0, Processors  #1
smpboot cpu 1: start_ip = 9b000
Initializing CPU#1
Disabled fast string operations
TSC synchronization [CPU#0 -> CPU#1]:
Measured 30 cycles TSC warp between CPUs, turning off TSC clock.
Marking TSC unstable due to check_tsc_sync_source failed
CPU 2 irqstacks, hard=f6c8e000 soft=f6c90000
 #2
smpboot cpu 2: start_ip = 9b000
Initializing CPU#2
Disabled fast string operations
CPU 3 irqstacks, hard=f6c9e000 soft=f6ca0000
 #3 Ok.
smpboot cpu 3: start_ip = 9b000
Initializing CPU#3
Disabled fast string operations
Brought up 4 CPUs
Total of 4 processors activated (13331.25 BogoMIPS).
PM: Registering ACPI NVS region at 7f68e000 (270336 bytes)
NET: Registered protocol family 16
EISA bus registered
ACPI: bus type pci registered
PCI: MMCONFIG for domain 0000 [bus 00-ff] at [mem 0xe0000000-0xefffffff] (base 0xe0000000)
PCI: not using MMCONFIG
PCI: PCI BIOS revision 3.00 entry at 0xf0031, last bus=5
PCI: Using configuration type 1 for base access
bio: create slab <bio-0> at 0
ACPI: Added _OSI(Module Device)
ACPI: Added _OSI(Processor Device)
ACPI: Added _OSI(3.0 _SCP Extensions)
ACPI: Added _OSI(Processor Aggregator Device)
ACPI: EC: EC description table is found, configuring boot EC
ACPI: Executed 1 blocks of module-level executable AML code
ACPI: SSDT 7f690740 0033A (v01  PmRef  Cpu0Ist 00003000 INTL 20051117)
ACPI: Dynamic OEM Table Load:
ACPI: SSDT   (null) 0033A (v01  PmRef  Cpu0Ist 00003000 INTL 20051117)
ACPI: SSDT 7f690c30 00724 (v01  PmRef  Cpu0Cst 00003001 INTL 20051117)
ACPI: Dynamic OEM Table Load:
ACPI: SSDT   (null) 00724 (v01  PmRef  Cpu0Cst 00003001 INTL 20051117)
ACPI: SSDT 7f690520 00217 (v01  PmRef  Cpu1Ist 00003000 INTL 20051117)
ACPI: Dynamic OEM Table Load:
ACPI: SSDT   (null) 00217 (v01  PmRef  Cpu1Ist 00003000 INTL 20051117)
ACPI: SSDT 7f690ba0 00085 (v01  PmRef  Cpu1Cst 00003000 INTL 20051117)
ACPI: Dynamic OEM Table Load:
ACPI: SSDT   (null) 00085 (v01  PmRef  Cpu1Cst 00003000 INTL 20051117)
ACPI: SSDT 7f690300 00217 (v01  PmRef  Cpu2Ist 00003000 INTL 20051117)
ACPI: Dynamic OEM Table Load:
ACPI: SSDT   (null) 00217 (v01  PmRef  Cpu2Ist 00003000 INTL 20051117)
ACPI: SSDT 7f690b10 00085 (v01  PmRef  Cpu2Cst 00003000 INTL 20051117)
ACPI: Dynamic OEM Table Load:
ACPI: SSDT   (null) 00085 (v01  PmRef  Cpu2Cst 00003000 INTL 20051117)
ACPI: SSDT 7f6900e0 00217 (v01  PmRef  Cpu3Ist 00003000 INTL 20051117)
ACPI: Dynamic OEM Table Load:
ACPI: SSDT   (null) 00217 (v01  PmRef  Cpu3Ist 00003000 INTL 20051117)
ACPI: SSDT 7f690a80 00085 (v01  PmRef  Cpu3Cst 00003000 INTL 20051117)
ACPI: Dynamic OEM Table Load:
ACPI: SSDT   (null) 00085 (v01  PmRef  Cpu3Cst 00003000 INTL 20051117)
ACPI: Interpreter enabled
ACPI: (supports S0 S3 S4 S5)
ACPI: Using IOAPIC for interrupt routing
PCI: MMCONFIG for domain 0000 [bus 00-ff] at [mem 0xe0000000-0xefffffff] (base 0xe0000000)
PCI: MMCONFIG at [mem 0xe0000000-0xefffffff] reserved in ACPI motherboard resources
PCI: Using MMCONFIG for extended config space
[Firmware Bug]: ACPI: BIOS _OSI(Linux) query ignored
ACPI: EC: GPE = 0x1c, I/O: command/status = 0x66, data = 0x62
ACPI: No dock devices found.
PCI: Using host bridge windows from ACPI; if necessary, use "pci=nocrs" and report a bug
ACPI: PCI Root Bridge [PCI0] (domain 0000 [bus 00-ff])
pci_root PNP0A08:00: host bridge window [io  0x0000-0x0cf7]
pci_root PNP0A08:00: host bridge window [io  0x0d00-0xffff]
pci_root PNP0A08:00: host bridge window [mem 0x000a0000-0x000bffff]
pci_root PNP0A08:00: host bridge window [mem 0x000d0000-0x000dffff]
pci_root PNP0A08:00: host bridge window [mem 0x7f700000-0xfed8ffff]
pci 0000:00:00.0: [8086:a010] type 0 class 0x000600
pci 0000:00:02.0: [8086:a011] type 0 class 0x000300
pci 0000:00:02.0: reg 10: [mem 0xf7e00000-0xf7e7ffff]
pci 0000:00:02.0: reg 14: [io  0xdc00-0xdc07]
pci 0000:00:02.0: reg 18: [mem 0xd0000000-0xdfffffff pref]
pci 0000:00:02.0: reg 1c: [mem 0xf7d00000-0xf7dfffff]
pci 0000:00:02.1: [8086:a012] type 0 class 0x000380
pci 0000:00:02.1: reg 10: [mem 0xf7e80000-0xf7efffff]
pci 0000:00:1b.0: [8086:27d8] type 0 class 0x000403
pci 0000:00:1b.0: reg 10: [mem 0xf7cf8000-0xf7cfbfff 64bit]
pci 0000:00:1b.0: PME# supported from D0 D3hot D3cold
pci 0000:00:1b.0: PME# disabled
pci 0000:00:1c.0: [8086:27d0] type 1 class 0x000604
pci 0000:00:1c.0: PME# supported from D0 D3hot D3cold
pci 0000:00:1c.0: PME# disabled
pci 0000:00:1c.1: [8086:27d2] type 1 class 0x000604
pci 0000:00:1c.1: PME# supported from D0 D3hot D3cold
pci 0000:00:1c.1: PME# disabled
pci 0000:00:1c.3: [8086:27d6] type 1 class 0x000604
pci 0000:00:1c.3: PME# supported from D0 D3hot D3cold
pci 0000:00:1c.3: PME# disabled
pci 0000:00:1d.0: [8086:27c8] type 0 class 0x000c03
pci 0000:00:1d.0: reg 20: [io  0xd400-0xd41f]
pci 0000:00:1d.1: [8086:27c9] type 0 class 0x000c03
pci 0000:00:1d.1: reg 20: [io  0xd480-0xd49f]
pci 0000:00:1d.2: [8086:27ca] type 0 class 0x000c03
pci 0000:00:1d.2: reg 20: [io  0xd800-0xd81f]
pci 0000:00:1d.3: [8086:27cb] type 0 class 0x000c03
pci 0000:00:1d.3: reg 20: [io  0xd880-0xd89f]
pci 0000:00:1d.7: [8086:27cc] type 0 class 0x000c03
pci 0000:00:1d.7: reg 10: [mem 0xf7cf7c00-0xf7cf7fff]
pci 0000:00:1d.7: PME# supported from D0 D3hot D3cold
pci 0000:00:1d.7: PME# disabled
pci 0000:00:1e.0: [8086:2448] type 1 class 0x000604
pci 0000:00:1f.0: [8086:27bc] type 0 class 0x000601
pci 0000:00:1f.2: [8086:27c1] type 0 class 0x000106
pci 0000:00:1f.2: reg 10: [io  0xd080-0xd087]
pci 0000:00:1f.2: reg 14: [io  0xd000-0xd003]
pci 0000:00:1f.2: reg 18: [io  0xcc00-0xcc07]
pci 0000:00:1f.2: reg 1c: [io  0xc880-0xc883]
pci 0000:00:1f.2: reg 20: [io  0xc800-0xc81f]
pci 0000:00:1f.2: reg 24: [mem 0xf7cf7800-0xf7cf7bff]
pci 0000:00:1f.2: PME# supported from D3hot
pci 0000:00:1f.2: PME# disabled
pci 0000:00:1c.0: PCI bridge to [bus 04-04]
pci 0000:02:00.0: [14e4:4727] type 0 class 0x000280
pci 0000:02:00.0: reg 10: [mem 0xfbffc000-0xfbffffff 64bit]
pci 0000:02:00.0: supports D1 D2
pci 0000:02:00.0: PME# supported from D0 D3hot D3cold
pci 0000:02:00.0: PME# disabled
pci 0000:00:1c.1: PCI bridge to [bus 02-03]
pci 0000:00:1c.1:   bridge window [mem 0xf8000000-0xfbffffff]
pci 0000:00:1c.1:   bridge window [mem 0xf0000000-0xf6ffffff 64bit pref]
pci 0000:01:00.0: [1969:2062] type 0 class 0x000200
pci 0000:01:00.0: reg 10: [mem 0xf7fc0000-0xf7ffffff 64bit]
pci 0000:01:00.0: reg 18: [io  0xec00-0xec7f]
pci 0000:01:00.0: PME# supported from D0 D1 D2 D3hot D3cold
pci 0000:01:00.0: PME# disabled
pci 0000:00:1c.3: PCI bridge to [bus 01-01]
pci 0000:00:1c.3:   bridge window [io  0xe000-0xefff]
pci 0000:00:1c.3:   bridge window [mem 0xf7f00000-0xf7ffffff]
pci 0000:00:1e.0: PCI bridge to [bus 05-05] (subtractive decode)
pci 0000:00:1e.0:   bridge window [io  0x0000-0x0cf7] (subtractive decode)
pci 0000:00:1e.0:   bridge window [io  0x0d00-0xffff] (subtractive decode)
pci 0000:00:1e.0:   bridge window [mem 0x000a0000-0x000bffff] (subtractive decode)
pci 0000:00:1e.0:   bridge window [mem 0x000d0000-0x000dffff] (subtractive decode)
pci 0000:00:1e.0:   bridge window [mem 0x7f700000-0xfed8ffff] (subtractive decode)
pci_bus 0000:00: on NUMA node 0
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P4._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P5._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P7._PRT]
 pci0000:00: Requesting ACPI _OSC control (0x1d)
 pci0000:00: ACPI _OSC request failed (AE_NOT_FOUND), returned control mask: 0x1d
ACPI _OSC control for PCIe not granted, disabling ASPM
ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 10 11 12 14 *15)
ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 *10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 *7 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 *5 6 7 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKG] (IRQs 3 *4 5 6 7 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKH] (IRQs *3 4 5 6 7 10 11 12 14 15)
vgaarb: device added: PCI:0000:00:02.0,decodes=io+mem,owns=io+mem,locks=none
vgaarb: loaded
vgaarb: bridge control possible 0000:00:02.0
SCSI subsystem initialized
libata version 3.00 loaded.
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
PCI: Using ACPI for IRQ routing
PCI: pci_cache_line_size set to 64 bytes
Expanded resource reserved due to conflict with PCI Bus 0000:00
reserve RAM buffer: 000000000009fc00 - 000000000009ffff
reserve RAM buffer: 000000007f680000 - 000000007fffffff
HPET: 3 timers in total, 0 timers will be used for per-cpu timer
Switching to clocksource hpet
Switched to NOHz mode on CPU #0
Switched to NOHz mode on CPU #1
Switched to NOHz mode on CPU #2
Switched to NOHz mode on CPU #3
pnp: PnP ACPI init
ACPI: bus type pnp registered
pnp 00:00: [bus 00-ff]
pnp 00:00: [io  0x0cf8-0x0cff]
pnp 00:00: [io  0x0000-0x0cf7 window]
pnp 00:00: [io  0x0d00-0xffff window]
pnp 00:00: [mem 0x000a0000-0x000bffff window]
pnp 00:00: [mem 0x000d0000-0x000dffff window]
pnp 00:00: [mem 0x7f700000-0xfed8ffff window]
pnp 00:00: Plug and Play ACPI device, IDs PNP0a08 PNP0a03 (active)
pnp 00:01: [mem 0xfed14000-0xfed19fff]
pnp 00:01: [mem 0xfed90000-0xfed93fff]
system 00:01: [mem 0xfed14000-0xfed19fff] has been reserved
system 00:01: [mem 0xfed90000-0xfed93fff] has been reserved
system 00:01: Plug and Play ACPI device, IDs PNP0c01 (active)
pnp 00:02: [dma 4]
pnp 00:02: [io  0x0000-0x000f]
pnp 00:02: [io  0x0081-0x0083]
pnp 00:02: [io  0x0087]
pnp 00:02: [io  0x0089-0x008b]
pnp 00:02: [io  0x008f]
pnp 00:02: [io  0x00c0-0x00df]
pnp 00:02: Plug and Play ACPI device, IDs PNP0200 (active)
pnp 00:03: [io  0x0070-0x0071]
pnp 00:03: [irq 8]
pnp 00:03: Plug and Play ACPI device, IDs PNP0b00 (active)
pnp 00:04: [io  0x0060]
pnp 00:04: [io  0x0064]
pnp 00:04: [irq 1]
pnp 00:04: Plug and Play ACPI device, IDs PNP0303 PNP030b (active)
pnp 00:05: [irq 12]
pnp 00:05: Plug and Play ACPI device, IDs SYN0a13 SYN0a00 SYN0002 PNP0f13 (active)
pnp 00:06: [io  0x0061]
pnp 00:06: Plug and Play ACPI device, IDs PNP0800 (active)
pnp 00:07: [io  0x00f0-0x00ff]
pnp 00:07: [irq 13]
pnp 00:07: Plug and Play ACPI device, IDs PNP0c04 (active)
pnp 00:08: [io  0x0010-0x001f]
pnp 00:08: [io  0x0022-0x003f]
pnp 00:08: [io  0x0044-0x004d]
pnp 00:08: [io  0x0050-0x005e]
pnp 00:08: [io  0x0063]
pnp 00:08: [io  0x0065]
pnp 00:08: [io  0x0067-0x006f]
pnp 00:08: [io  0x0072-0x007f]
pnp 00:08: [io  0x0080]
pnp 00:08: [io  0x0084-0x0086]
pnp 00:08: [io  0x0088]
pnp 00:08: [io  0x008c-0x008e]
pnp 00:08: [io  0x0090-0x009f]
pnp 00:08: [io  0x00a2-0x00bf]
pnp 00:08: [io  0x00e0-0x00ef]
pnp 00:08: [io  0x025c-0x025f]
pnp 00:08: [io  0x0380-0x0383]
pnp 00:08: [io  0x0400-0x041f]
pnp 00:08: [io  0x04d0-0x04d1]
pnp 00:08: [io  0x0800-0x087f]
pnp 00:08: [io  0x0400-0x03ff disabled]
pnp 00:08: [io  0x0480-0x04bf]
pnp 00:08: [mem 0xfed1c000-0xfed1ffff]
pnp 00:08: [mem 0xfed20000-0xfed3ffff]
pnp 00:08: [mem 0xfed50000-0xfed8ffff]
pnp 00:08: [mem 0xffb00000-0xffbfffff]
pnp 00:08: [mem 0xfff00000-0xffffffff]
system 00:08: [io  0x025c-0x025f] has been reserved
system 00:08: [io  0x0380-0x0383] has been reserved
system 00:08: [io  0x0400-0x041f] has been reserved
system 00:08: [io  0x04d0-0x04d1] has been reserved
system 00:08: [io  0x0800-0x087f] has been reserved
system 00:08: [io  0x0480-0x04bf] has been reserved
system 00:08: [mem 0xfed1c000-0xfed1ffff] has been reserved
system 00:08: [mem 0xfed20000-0xfed3ffff] has been reserved
system 00:08: [mem 0xfed50000-0xfed8ffff] has been reserved
system 00:08: [mem 0xffb00000-0xffbfffff] has been reserved
system 00:08: [mem 0xfff00000-0xffffffff] has been reserved
system 00:08: Plug and Play ACPI device, IDs PNP0c02 (active)
pnp 00:09: [mem 0xfed00000-0xfed003ff]
pnp 00:09: Plug and Play ACPI device, IDs PNP0103 (active)
pnp 00:0a: [mem 0xfec00000-0xfec00fff]
pnp 00:0a: [mem 0xfee00000-0xfee00fff]
system 00:0a: [mem 0xfec00000-0xfec00fff] could not be reserved
system 00:0a: [mem 0xfee00000-0xfee00fff] has been reserved
system 00:0a: Plug and Play ACPI device, IDs PNP0c02 (active)
pnp 00:0b: [mem 0xe0000000-0xefffffff]
system 00:0b: [mem 0xe0000000-0xefffffff] has been reserved
system 00:0b: Plug and Play ACPI device, IDs PNP0c02 (active)
pnp 00:0c: [mem 0x00000000-0x0009ffff]
pnp 00:0c: [mem 0x000c0000-0x000cffff]
pnp 00:0c: [mem 0x000e0000-0x000fffff]
pnp 00:0c: [mem 0x00100000-0x7f6fffff]
pnp 00:0c: [mem 0xfed90000-0xffffffff]
system 00:0c: [mem 0x00000000-0x0009ffff] could not be reserved
system 00:0c: [mem 0x000c0000-0x000cffff] could not be reserved
system 00:0c: [mem 0x000e0000-0x000fffff] could not be reserved
system 00:0c: [mem 0x00100000-0x7f6fffff] could not be reserved
system 00:0c: [mem 0xfed90000-0xffffffff] could not be reserved
system 00:0c: Plug and Play ACPI device, IDs PNP0c01 (active)
pnp: PnP ACPI: found 13 devices
ACPI: ACPI bus type pnp unregistered
PCI: max bus depth: 1 pci_try_num: 2
pci 0000:00:1c.3: BAR 9: assigned [mem 0x80000000-0x801fffff 64bit pref]
pci 0000:00:1c.1: BAR 7: assigned [io  0x1000-0x1fff]
pci 0000:00:1c.0: BAR 8: assigned [mem 0x80200000-0x803fffff]
pci 0000:00:1c.0: BAR 9: assigned [mem 0x80400000-0x805fffff 64bit pref]
pci 0000:00:1c.0: BAR 7: assigned [io  0x2000-0x2fff]
pci 0000:00:1c.0: PCI bridge to [bus 04-04]
pci 0000:00:1c.0:   bridge window [io  0x2000-0x2fff]
pci 0000:00:1c.0:   bridge window [mem 0x80200000-0x803fffff]
pci 0000:00:1c.0:   bridge window [mem 0x80400000-0x805fffff 64bit pref]
pci 0000:00:1c.1: PCI bridge to [bus 02-03]
pci 0000:00:1c.1:   bridge window [io  0x1000-0x1fff]
pci 0000:00:1c.1:   bridge window [mem 0xf8000000-0xfbffffff]
pci 0000:00:1c.1:   bridge window [mem 0xf0000000-0xf6ffffff 64bit pref]
pci 0000:00:1c.3: PCI bridge to [bus 01-01]
pci 0000:00:1c.3:   bridge window [io  0xe000-0xefff]
pci 0000:00:1c.3:   bridge window [mem 0xf7f00000-0xf7ffffff]
pci 0000:00:1c.3:   bridge window [mem 0x80000000-0x801fffff 64bit pref]
pci 0000:00:1e.0: PCI bridge to [bus 05-05]
pci 0000:00:1c.0: enabling device (0104 -> 0107)
pci 0000:00:1c.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
pci 0000:00:1c.0: setting latency timer to 64
pci 0000:00:1c.1: enabling device (0106 -> 0107)
pci 0000:00:1c.1: PCI INT B -> GSI 17 (level, low) -> IRQ 17
pci 0000:00:1c.1: setting latency timer to 64
pci 0000:00:1c.3: PCI INT D -> GSI 19 (level, low) -> IRQ 19
pci 0000:00:1c.3: setting latency timer to 64
pci 0000:00:1e.0: setting latency timer to 64
pci_bus 0000:00: resource 4 [io  0x0000-0x0cf7]
pci_bus 0000:00: resource 5 [io  0x0d00-0xffff]
pci_bus 0000:00: resource 6 [mem 0x000a0000-0x000bffff]
pci_bus 0000:00: resource 7 [mem 0x000d0000-0x000dffff]
pci_bus 0000:00: resource 8 [mem 0x7f700000-0xfed8ffff]
pci_bus 0000:04: resource 0 [io  0x2000-0x2fff]
pci_bus 0000:04: resource 1 [mem 0x80200000-0x803fffff]
pci_bus 0000:04: resource 2 [mem 0x80400000-0x805fffff 64bit pref]
pci_bus 0000:02: resource 0 [io  0x1000-0x1fff]
pci_bus 0000:02: resource 1 [mem 0xf8000000-0xfbffffff]
pci_bus 0000:02: resource 2 [mem 0xf0000000-0xf6ffffff 64bit pref]
pci_bus 0000:01: resource 0 [io  0xe000-0xefff]
pci_bus 0000:01: resource 1 [mem 0xf7f00000-0xf7ffffff]
pci_bus 0000:01: resource 2 [mem 0x80000000-0x801fffff 64bit pref]
pci_bus 0000:05: resource 4 [io  0x0000-0x0cf7]
pci_bus 0000:05: resource 5 [io  0x0d00-0xffff]
pci_bus 0000:05: resource 6 [mem 0x000a0000-0x000bffff]
pci_bus 0000:05: resource 7 [mem 0x000d0000-0x000dffff]
pci_bus 0000:05: resource 8 [mem 0x7f700000-0xfed8ffff]
NET: Registered protocol family 2
IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
TCP bind hash table entries: 65536 (order: 7, 524288 bytes)
TCP: Hash tables configured (established 131072 bind 65536)
TCP reno registered
UDP hash table entries: 512 (order: 2, 16384 bytes)
UDP-Lite hash table entries: 512 (order: 2, 16384 bytes)
NET: Registered protocol family 1
pci 0000:00:02.0: Boot video device
PCI: CLS 32 bytes, default 64
Trying to unpack rootfs image as initramfs...
Freeing initrd memory: 24228k freed
highmem bounce pool size: 64 pages
VFS: Disk quotas dquot_6.5.2
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
aufs 3.1
msgmni has been set to 1731
Block layer SCSI generic (bsg) driver version 0.4 loaded (major 254)
io scheduler noop registered
io scheduler deadline registered
io scheduler cfq registered (default)
pcieport 0000:00:1c.0: setting latency timer to 64
pcieport 0000:00:1c.0: irq 40 for MSI/MSI-X
pcieport 0000:00:1c.1: setting latency timer to 64
pcieport 0000:00:1c.1: irq 41 for MSI/MSI-X
pcieport 0000:00:1c.3: setting latency timer to 64
pcieport 0000:00:1c.3: irq 42 for MSI/MSI-X
Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
lp: driver loaded but no devices found
Real Time Clock Driver v1.12b
Linux agpgart interface v0.103
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
brd: module loaded
loop: module loaded
ahci 0000:00:1f.2: version 3.0
ahci 0000:00:1f.2: PCI INT B -> GSI 21 (level, low) -> IRQ 21
ahci 0000:00:1f.2: irq 43 for MSI/MSI-X
ahci 0000:00:1f.2: AHCI 0001.0100 32 slots 4 ports 3 Gbps 0x1 impl SATA mode
ahci 0000:00:1f.2: flags: 64bit ncq pm led clo pio slum part
ahci 0000:00:1f.2: setting latency timer to 64
scsi0 : ahci
scsi1 : ahci
scsi2 : ahci
scsi3 : ahci
ata1: SATA max UDMA/133 abar m1024@0xf7cf7800 port 0xf7cf7900 irq 43
ata2: DUMMY
ata3: DUMMY
ata4: DUMMY
PPP generic driver version 2.4.2
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
ehci_hcd 0000:00:1d.7: PCI INT A -> GSI 23 (level, low) -> IRQ 23
ehci_hcd 0000:00:1d.7: setting latency timer to 64
ehci_hcd 0000:00:1d.7: EHCI Host Controller
ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 1
ehci_hcd 0000:00:1d.7: using broken periodic workaround
ehci_hcd 0000:00:1d.7: debug port 1
ehci_hcd 0000:00:1d.7: cache line size of 32 is not supported
ehci_hcd 0000:00:1d.7: irq 23, io mem 0xf7cf7c00
ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00
usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb1: Product: EHCI Host Controller
usb usb1: Manufacturer: Linux 3.1.5-calculate ehci_hcd
usb usb1: SerialNumber: 0000:00:1d.7
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 8 ports detected
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
i8042: PNP: PS/2 Controller [PNP0303:PS2K,PNP0f13:PS2M] at 0x60,0x64 irq 1,12
serio: i8042 KBD port at 0x60,0x64 irq 1
serio: i8042 AUX port at 0x60,0x64 irq 12
mousedev: PS/2 mouse device common for all mice
EISA: Probing bus 0 at eisa.0
EISA: Cannot allocate resource for mainboard
cpuidle: using governor ladder
cpuidle: using governor menu
usbcore: registered new interface driver usbhid
usbhid: USB HID core driver
TCP cubic registered
Registering the dns_resolver key type
Using IPI No-Shortcut mode
PM: Hibernation image not present or could not be loaded.
registered taskstats version 1
input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input0
ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata1.00: unexpected _GTF length (8)
usb 1-6: new high speed USB device number 2 using ehci_hcd
ata1.00: ATA-8: ST9320325AS, 0003SDM1, max UDMA/133
ata1.00: 625142448 sectors, multi 16: LBA48 NCQ (depth 31/32)
ata1.00: unexpected _GTF length (8)
ata1.00: configured for UDMA/133
scsi 0:0:0:0: Direct-Access     ATA      ST9320325AS      0003 PQ: 0 ANSI: 5
sd 0:0:0:0: [sda] 625142448 512-byte logical blocks: (320 GB/298 GiB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
 sda: sda1 sda2 sda3
sd 0:0:0:0: [sda] Attached SCSI disk
Freeing unused kernel memory: 456k freed
Write protecting the kernel text: 3164k
Write protecting the kernel read-only data: 976k
input: Lid Switch as /devices/LNXSYSTM:00/device:00/PNP0C0D:00/input/input1
ACPI: Lid Switch [LID]
input: Sleep Button as /devices/LNXSYSTM:00/device:00/PNP0C0E:00/input/input2
ACPI: Sleep Button [SLPB]
input: Power Button as /devices/LNXSYSTM:00/device:00/PNP0C0C:00/input/input3
ACPI: Power Button [PWRB]
input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input4
ACPI: Power Button [PWRF]
agpgart-intel 0000:00:00.0: Intel GMA3150 Chipset
agpgart-intel 0000:00:00.0: detected gtt size: 524288K total, 262144K mappable
agpgart-intel 0000:00:00.0: detected 8192K stolen memory
agpgart-intel 0000:00:00.0: AGP aperture is 256M @ 0xd0000000
[drm] Initialized drm 1.1.0 20060810
i915 0000:00:02.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
i915 0000:00:02.0: setting latency timer to 64
usb 1-6: New USB device found, idVendor=13d3, idProduct=5711
usb 1-6: New USB device strings: Mfr=3, Product=1, SerialNumber=2
usb 1-6: Product: USB 2.0 UVC VGA WebCam
usb 1-6: Manufacturer: Azurewave
usb 1-6: SerialNumber: 0x0001
i915 0000:00:02.0: irq 44 for MSI/MSI-X
[drm] Supports vblank timestamp caching Rev 1 (10.10.2010).
[drm] Driver supports precise vblank timestamp query.
vgaarb: device changed decodes: PCI:0000:00:02.0,olddecodes=io+mem,decodes=io+mem:owns=io+mem
[drm] initialized overlay support
fbcon: inteldrmfb (fb0) is primary device
Console: switching to colour frame buffer device 128x37
fb0: inteldrmfb frame buffer device
drm: registered panic notifier
acpi device:2c: registered as cooling_device0
input: Video Bus as /devices/LNXSYSTM:00/device:00/PNP0A08:00/LNXVIDEO:00/input/input5
ACPI: Video Device [VGA] (multi-head: yes  rom: no  post: no)
[drm] Initialized i915 1.6.0 20080730 for 0000:00:02.0 on minor 0
fbcondecor: console 0 using theme 'tty1'
fbcondecor: switched decor state to 'on' on console 0
ACPI: acpi_idle registered with cpuidle
Monitor-Mwait will be used to enter C-1 state
Monitor-Mwait will be used to enter C-2 state
ACPI: Deprecated procfs I/F for AC is loaded, please retry with CONFIG_ACPI_PROCFS_POWER cleared
ACPI: AC Adapter [AC0] (on-line)
wmi: Mapper loaded
uhci_hcd: USB Universal Host Controller Interface driver
uhci_hcd 0000:00:1d.0: PCI INT A -> GSI 23 (level, low) -> IRQ 23
uhci_hcd 0000:00:1d.0: setting latency timer to 64
uhci_hcd 0000:00:1d.0: UHCI Host Controller
uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 2
uhci_hcd 0000:00:1d.0: irq 23, io base 0x0000d400
usb usb2: New USB device found, idVendor=1d6b, idProduct=0001
usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb2: Product: UHCI Host Controller
usb usb2: Manufacturer: Linux 3.1.5-calculate uhci_hcd
usb usb2: SerialNumber: 0000:00:1d.0
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
uhci_hcd 0000:00:1d.1: PCI INT B -> GSI 19 (level, low) -> IRQ 19
uhci_hcd 0000:00:1d.1: setting latency timer to 64
uhci_hcd 0000:00:1d.1: UHCI Host Controller
uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 3
uhci_hcd 0000:00:1d.1: irq 19, io base 0x0000d480
usb usb3: New USB device found, idVendor=1d6b, idProduct=0001
usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb3: Product: UHCI Host Controller
usb usb3: Manufacturer: Linux 3.1.5-calculate uhci_hcd
usb usb3: SerialNumber: 0000:00:1d.1
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
uhci_hcd 0000:00:1d.2: PCI INT C -> GSI 18 (level, low) -> IRQ 18
uhci_hcd 0000:00:1d.2: setting latency timer to 64
uhci_hcd 0000:00:1d.2: UHCI Host Controller
uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 4
uhci_hcd 0000:00:1d.2: irq 18, io base 0x0000d800
usb usb4: New USB device found, idVendor=1d6b, idProduct=0001
usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb4: Product: UHCI Host Controller
usb usb4: Manufacturer: Linux 3.1.5-calculate uhci_hcd
usb usb4: SerialNumber: 0000:00:1d.2
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 2 ports detected
uhci_hcd 0000:00:1d.3: PCI INT D -> GSI 16 (level, low) -> IRQ 16
uhci_hcd 0000:00:1d.3: setting latency timer to 64
uhci_hcd 0000:00:1d.3: UHCI Host Controller
uhci_hcd 0000:00:1d.3: new USB bus registered, assigned bus number 5
uhci_hcd 0000:00:1d.3: irq 16, io base 0x0000d880
usb usb5: New USB device found, idVendor=1d6b, idProduct=0001
usb usb5: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb5: Product: UHCI Host Controller
usb usb5: Manufacturer: Linux 3.1.5-calculate uhci_hcd
usb usb5: SerialNumber: 0000:00:1d.3
hub 5-0:1.0: USB hub found
hub 5-0:1.0: 2 ports detected
sd 0:0:0:0: Attached scsi generic sg0 type 0
thermal LNXTHERM:00: registered as thermal_zone0
ACPI: Thermal Zone [TZ00] (64 C)
ACPI: Deprecated procfs I/F for battery is loaded, please retry with CONFIG_ACPI_PROCFS_POWER cleared
ACPI: Battery Slot [BAT0] (battery present)
cfg80211: Calling CRDA to update world regulatory domain
brcmutil: module is from the staging directory, the quality is unknown, you have been warned.
brcmsmac: module is from the staging directory, the quality is unknown, you have been warned.
brcmsmac 0000:02:00.0: bus 2 slot 0 func 0 irq 10
brcmsmac 0000:02:00.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17
brcmsmac 0000:02:00.0: setting latency timer to 64
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
asus_wmi: ASUS WMI generic driver loaded
asus_wmi: Initialization: 0x0
asus_wmi: BIOS WMI version: 0.8
asus_wmi: SFUN value: 0x0
input: Eee PC WMI hotkeys as /devices/platform/eeepc-wmi/input/input6
ieee80211 phy0: brcmsmac: fail to load firmware brcm/bcm43xx-0.fw
ieee80211 phy0: brcmsmac: Failed to find firmware usually in /lib/firmware/brcm
brcmsmac 0000:02:00.0: PCI INT A disabled
brcmsmac: brcms_pci_probe: brcms_attach failed!
bcma-pci-bridge 0000:02:00.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17
bcma-pci-bridge 0000:02:00.0: setting latency timer to 64
bcma: Core 0 found: ChipCommon (manuf 0x4BF, id 0x800, rev 0x24, class 0x0)
bcma: Core 1 found: IEEE 802.11 (manuf 0x4BF, id 0x812, rev 0x18, class 0x0)
bcma: Core 2 found: PCIe (manuf 0x4BF, id 0x820, rev 0x11, class 0x0)
bcma: Bus registered
alps.c: E6 report: 3c 03 c8
elantech: assuming hardware version 2, firmware version 20.1.0
elantech: Synaptics capabilities query result 0x68, 0x15, 0x0a.
elantech: retrying ps2 command 0xe6 (2).
asus_wmi: Backlight controlled by ACPI video driver
elantech: retrying ps2 command 0xf8 (2).
PM: Starting manual resume from disk
PM: Hibernation image partition 8:2 present
PM: Looking for hibernation image.
PM: Image not found (code -22)
PM: Hibernation image not present or could not be loaded.
EXT4-fs (sda1): mounted filesystem with ordered data mode. Opts: (null)
elantech: retrying ps2 command 0xf8 (1).
input: ETPS/2 Elantech Touchpad as /devices/platform/i8042/serio1/input/input7
udev[2042]: starting version 164
atl1c 0000:01:00.0: PCI INT A -> GSI 19 (level, low) -> IRQ 19
atl1c 0000:01:00.0: setting latency timer to 64
atl1c 0000:01:00.0: version 1.0.1.0-NAPI
snd_hda_intel 0000:00:1b.0: PCI INT A -> GSI 22 (level, low) -> IRQ 22
snd_hda_intel 0000:00:1b.0: irq 45 for MSI/MSI-X
snd_hda_intel 0000:00:1b.0: setting latency timer to 64
hda_codec: ALC269VB: BIOS auto-probing.
input: HDA Intel Headphone as /devices/pci0000:00/0000:00:1b.0/sound/card0/input8
iTCO_vendor_support: vendor-support=0
iTCO_wdt: Intel TCO WatchDog Timer Driver v1.06
iTCO_wdt: Found a NM10 TCO device (Version=2, TCOBASE=0x0860)
iTCO_wdt: initialized. heartbeat=30 sec (nowayout=0)
Linux video capture interface: v2.00
uvcvideo: Found UVC 1.00 device USB 2.0 UVC VGA WebCam (13d3:5711)
input: USB 2.0 UVC VGA WebCam as /devices/pci0000:00/0000:00:1d.7/usb1/1-6/1-6:1.0/input/input9
usbcore: registered new interface driver uvcvideo
USB Video Class driver (1.1.1)
EXT4-fs (sda1): re-mounted. Opts: (null)
EXT4-fs (sda3): mounted filesystem with ordered data mode. Opts: (null)
atl1c 0000:01:00.0: irq 46 for MSI/MSI-X
atl1c 0000:01:00.0: atl1c: eth0 NIC Link is Up<100 Mbps Full Duplex>
NET: Registered protocol family 17
NET: Registered protocol family 10
fbcondecor: console 1 using theme 'tty2'
fbcondecor: switched decor state to 'on' on console 1
fbcondecor: console 2 using theme 'tty3'
fbcondecor: switched decor state to 'on' on console 2
fbcondecor: console 3 using theme 'tty4'
fbcondecor: switched decor state to 'on' on console 3
fbcondecor: console 4 using theme 'tty5'
fbcondecor: switched decor state to 'on' on console 4
fbcondecor: console 5 using theme 'tty6'
fbcondecor: switched decor state to 'on' on console 5
fbcondecor: switched decor state to 'off' on console 0
fbcondecor: console 0 using theme 'tty1'
fbcondecor: switched decor state to 'on' on console 0
eth0: no IPv6 routers present
fbcondecor: switched decor state to 'off' on console 0
fbcondecor: console 0 using theme 'tty1'
fbcondecor: switched decor state to 'on' on console 0
EXT4-fs (sda1): re-mounted. Opts: commit=0
EXT4-fs (sda3): re-mounted. Opts: commit=0
process `skype' is using obsolete setsockopt SO_BSDCOMPAT