API tools faq
paste
Advertisement
mgmzog

DSL-2500 openwrt boot OK2

mgmzog
May 2nd, 2014
449
0
Never
Add comment
Not a member of Pastebin yet? Sign Up, it unlocks many cool features!
text 8.53 KB | None | 0 0
raw download clone embed print report
  1. CFE version 1.0.37-12.1 for BCM96338 (32bit,SP,BE)
  2. Build Date: Mon Jun 9 01:35:26 CST 2008 ([email protected])
  3. Copyright (C) 2000-2006 Broadcom Corporation.
  4.  
  5. Boot Address 0xbfc00000
  6.  
  7. Initializing Arena.
  8. Initializing Devices.
  9. Serial flash device: name NXW25P16, id 0xef14, size 2048KB
  10. Auto-negotiation timed-out
  11. 100 MB Full-Duplex (auto-neg)
  12. CPU type 0x29010: 240MHz
  13. Total memory: 33554432 bytes (32MB)
  14.  
  15. Total memory used by CFE: 0x80401000 - 0x80528710 (1210128)
  16. Initialized Data: 0x8041D740 - 0x8041FF30 (10224)
  17. BSS Area: 0x8041FF30 - 0x80426710 (26592)
  18. Local Heap: 0x80426710 - 0x80526710 (1048576)
  19. Stack Area: 0x80526710 - 0x80528710 (8192)
  20. Text (code) segment: 0x80401000 - 0x8041D734 (116532)
  21. Boot area (physical): 0x00529000 - 0x00569000
  22. Relocation Factor: I:00000000 - D:00000000
  23.  
  24. Board IP address : 192.168.1.100:ffffff00
  25. Host IP address : 192.168.1.25
  26. Gateway IP address :
  27. Run from flash/host (f/h) : f
  28. Default host run file name : vmlinux
  29. Default host flash file name : bcm963xx_fs_kernel
  30. Boot delay (0-9 seconds) : 1
  31. Board Id (0-14) : 96332CG_F4W
  32. Number of MAC Addresses (1-32) : 11
  33. Base MAC Address : 00:24:01:5b:e0:84
  34. PSI Size (1-64) KBytes : 24
  35.  
  36. *** Press any key to stop auto run (1 seconds) ***
  37. Auto run second count down: 110
  38. Booting from only image (0xbfc10000) ...
  39. Code Address: 0x80010000, Entry Address: 0x80010000
  40. Decompression OK!
  41. Entry at 0x80010000
  42. Closing network.
  43. Starting program at 0x80010000
  44. [ 0.000000] Linux version 3.10.36 (archie@build41) (gcc version 4.8.3 (OpenWrt/Linaro GCC 4.8-2014.01 r40569) ) #45 Fri May 2 15:30:07 EEST 2014
  45. [ 0.000000] Detected Broadcom 0x6338 CPU revision a2
  46. [ 0.000000] CPU frequency is 240 MHz
  47. [ 0.000000] 32MB of RAM installed
  48. [ 0.000000] registering 8 GPIOs
  49. [ 0.000000] board_bcm963xx: Boot address 0xbfc00000
  50. [ 0.000000] board_bcm963xx: CFE version: unknown
  51. [ 0.000000] bootconsole [early0] enabled
  52. [ 0.000000] CPU revision is: 00029010 (Broadcom BCM6338)
  53. [ 0.000000] board_bcm963xx: board name: 96332CG_F4W
  54. [ 0.000000] Determined physical RAM map:
  55. [ 0.000000] memory: 02000000 @ 00000000 (usable)
  56. [ 0.000000] Initrd not found or empty - disabling initrd
  57. [ 0.000000] Zone ranges:
  58. [ 0.000000] Normal [mem 0x00000000-0x01ffffff]
  59. [ 0.000000] Movable zone start for each node
  60. [ 0.000000] Early memory node ranges
  61. [ 0.000000] node 0: [mem 0x00000000-0x01ffffff]
  62. [ 0.000000] Primary instruction cache 16kB, VIPT, 2-way, linesize 16 bytes.
  63. [ 0.000000] Primary data cache 8kB, 2-way, VIPT, no aliases, linesize 16 bytes
  64. [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 8128
  65. [ 0.000000] Kernel command line: root=/dev/mtdblock2 rootfstype=squashfs,jffs2 noinitrd console=ttyS0,115200
  66. [ 0.000000] PID hash table entries: 128 (order: -3, 512 bytes)
  67. [ 0.000000] Dentry cache hash table entries: 4096 (order: 2, 16384 bytes)
  68. [ 0.000000] Inode-cache hash table entries: 2048 (order: 1, 8192 bytes)
  69. [ 0.000000] Memory: 29476k/32768k available (2102k kernel code, 3292k reserved, 342k data, 240k init, 0k highmem)
  70. [ 0.000000] NR_IRQS:256
  71. [ 0.000000] Calibrating delay loop... 237.82 BogoMIPS (lpj=475648)
  72. [ 0.040000] pid_max: default: 32768 minimum: 301
  73. [ 0.044000] Mount-cache hash table entries: 512
  74. [ 0.060000] NET: Registered protocol family 16
  75. [ 0.124000] bio: create slab <bio-0> at 0
  76. [ 0.144000] Switching to clocksource MIPS
  77. [ 0.172000] NET: Registered protocol family 2
  78. [ 0.180000] TCP established hash table entries: 512 (order: 0, 4096 bytes)
  79. [ 0.188000] TCP bind hash table entries: 512 (order: -1, 2048 bytes)
  80. [ 0.192000] TCP: Hash tables configured (established 512 bind 512)
  81. [ 0.200000] TCP: reno registered
  82. [ 0.204000] UDP hash table entries: 256 (order: 0, 4096 bytes)
  83. [ 0.212000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
  84. [ 0.220000] NET: Registered protocol family 1
  85. [ 0.232000] audit: initializing netlink socket (disabled)
  86. [ 0.240000] type=2000 audit(0.239:1): initialized
  87. [ 0.248000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
  88. [ 0.252000] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
  89. [ 0.264000] msgmni has been set to 57
  90. [ 0.272000] io scheduler noop registered
  91. [ 0.276000] io scheduler deadline registered (default)
  92. [ 0.288000] bcm63xx_uart.0: ttyS0 at MMIO 0xfffe0300 (irq = 10) is a bcm63xx_uart
  93. [ 0.296000] console [ttyS0] enabled, bootconsole disabled
  94. [ 0.296000] console [ttyS0] enabled, bootconsole disabled
  95. [ 0.328000] m25p80 spi0.0: found w25x16, expected m25p80
  96. [ 0.336000] m25p80 spi0.0: w25x16 (2048 Kbytes)
  97. [ 0.344000] bcm63xxpart: CFE boot tag found with version 6 and board type 96332CG_F4W
  98. [ 0.352000] bcm63xxpart: Partition 0 is CFE offset 0 and length 10000
  99. [ 0.360000] bcm63xxpart: Partition 1 is kernel offset 10100 and length dff00
  100. [ 0.368000] bcm63xxpart: Partition 2 is rootfs offset f0000 and length 100000
  101. [ 0.376000] bcm63xxpart: Partition 3 is nvram offset 1f0000 and length 10000
  102. [ 0.384000] bcm63xxpart: Partition 4 is linux offset 10000 and length 1e0000
  103. [ 0.392000] bcm63xxpart: Spare partition is offset 170004 and length 7fffc
  104. [ 0.396000] 5 bcm63xxpart partitions found on MTD device spi0.0
  105. [ 0.404000] Creating 5 MTD partitions on "spi0.0":
  106. [ 0.408000] 0x000000000000-0x000000010000 : "CFE"
  107. [ 0.424000] 0x000000010100-0x0000000f0000 : "kernel"
  108. [ 0.428000] mtd: partition "kernel" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
  109. [ 0.448000] 0x0000000f0000-0x0000001f0000 : "rootfs"
  110. [ 0.464000] mtd: device 2 (rootfs) set to be root filesystem
  111. [ 0.472000] mtd: partition "rootfs_data" created automatically, ofs=0x170000, len=0x80000
  112. [ 0.480000] 0x000000170000-0x0000001f0000 : "rootfs_data"
  113. [ 0.492000] 0x0000001f0000-0x000000200000 : "nvram"
  114. [ 0.508000] 0x000000010000-0x0000001f0000 : "linux"
  115. [ 0.520000] bcm63xx-spi bcm63xx-spi: at 0xfffe0c00 (irq 9, FIFOs size 63)
  116. [ 0.556000] libphy: bcm63xx_enet MII bus: probed
  117. [ 0.560000] bcm63xx_enet bcm63xx_enet.0: attached PHY at address 1 [Broadcom BCM63XX (1)]
  118. [ 0.580000] bcm63xx-wdt bcm63xx-wdt: started, timer margin: 30 sec
  119. [ 0.604000] TCP: cubic registered
  120. [ 0.608000] NET: Registered protocol family 17
  121. [ 0.616000] 8021q: 802.1Q VLAN Support v1.8
  122. [ 0.700000] VFS: Mounted root (squashfs filesystem) readonly on device 31:2.
  123. [ 0.712000] Freeing unused kernel memory: 240K (80274000 - 802b0000)
  124. procd: Console is alive
  125. procd: - watchdog -
  126. procd: - preinit -
  127. [ 12.688000] Button Hotplug driver version 0.4.1
  128. Press the [f] key and hit [enter] to enter failsafe mode
  129. Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level
  130. jffs2 is ready
  131. [ 18.100000] jffs2: notice: (201) jffs2_build_xattr_subsystem: complete building xattr subsystem, 1 of xdatum (0 unchecked, 0 orphan) and 6 of xref (0 dead, 0 orphan) found.
  132. switching to jffs2
  133. procd: - early -
  134. procd: - watchdog -
  135. procd: - ubus -
  136. procd: - init -
  137. Please press Enter to activate this console.
  138.  
  139.  
  140.  
  141. BusyBox v1.19.4 (2014-04-28 22:50:28 EEST) built-in shell (ash)
  142. Enter 'help' for a list of built-in commands.
  143.  
  144. _______ ________ __
  145. | |.-----.-----.-----.| | | |.----.| |_
  146. | - || _ | -__| || | | || _|| _|
  147. |_______|| __|_____|__|__||________||__| |____|
  148. |__| W I R E L E S S F R E E D O M
  149. -----------------------------------------------------
  150. BARRIER BREAKER (Bleeding Edge, r40569)
  151. -----------------------------------------------------
  152. * 1/2 oz Galliano Pour all ingredients into
  153. * 4 oz cold Coffee an irish coffee mug filled
  154. * 1 1/2 oz Dark Rum with crushed ice. Stir.
  155. * 2 tsp. Creme de Cacao
  156. -----------------------------------------------------
  157. root@OpenWrt:/# pin[ 29.132000] eth0: link UP - 100/full - flow control off
  158. g procd: - init complete -
  159. 192.1.68.1.1
  160. PING 192.168.1.1 (192.168.1.1): 56 data bytes
  161. 64 bytes from 192.168.1.1: seq=0 ttl=64 time=2.111 ms
  162. 64 bytes from 192.168.1.1: seq=1 ttl=64 time=1.013 ms
  163. ^C
  164. --- 192.168.1.1 ping statistics ---
  165. 2 packets transmitted, 2 packets received, 0% packet loss
  166. round-trip min/avg/max = 1.013/1.562/2.111 ms
  167. root@OpenWrt:/#
Advertisement
Add Comment
Please, Sign In to add comment
Advertisement
Public Pastes
Advertisement
We use cookies for various purposes including analytics. By continuing to use Pastebin, you agree to our use of cookies as described in the Cookies Policy.  OK, I Understand
Not a member of Pastebin yet?
Sign Up, it unlocks many cool features!