OMAP3 beagleboard.org # nand erase 260000 20000

NAND erase: device 0 offset 0x260000, size 0x20000
Erasing at 0x260000 -- 100% complete.
OK
OMAP3 beagleboard.org # printenv
bootcmd=if mmc init ${mmcdev}; then if userbutton; then setenv bootscr user.scr;if run loadbootscript; then run bootscript; else if run loaduimage; then if r
un loadramdisk; then run ramboot; else run mmcboot; fi; fi; fi; else setenv bootscr boot.scr; if run loadbootscript; then run bootscript; else if run loaduim
age; then run mmcboot; else run nandboot; fi; fi; fi; else run nandboot; fi
bootdelay=3
baudrate=115200
loadaddr=0x80200000
rdaddr=0x81600000
usbtty=cdc_acm
console=ttyS2,115200n8
optargs=
bootscr=boot.scr
camera=lbcm3m1
vram=12M
dvimode=640x480MR-16@60
defaultdisplay=dvi
mmcdev=1
mmcroot=/dev/mmcblk0p2 rw
mmcrootfstype=ext3 rootwait
nandroot=/dev/mtdblock4 rw
nandrootfstype=jffs2
ramroot=/dev/ram0 rw ramdisk_size=65536 initrd=${rdaddr},64M
ramrootfstype=ext2
mmcargs=setenv bootargs console=${console} ${optargs} mpurate=${mpurate} buddy=${buddy} camera=${camera} vram=${vram} omapfb.mode=dvi:${dvimode} omapdss.def_
disp=${defaultdisplay} root=${mmcroot} rootfstype=${mmcrootfstype}
nandargs=setenv bootargs console=${console} ${optargs} mpurate=${mpurate} buddy=${buddy} camera=${camera} vram=${vram} omapfb.mode=dvi:${dvimode} omapdss.def
_disp=${defaultdisplay} root=${nandroot} rootfstype=${nandrootfstype}
loadbootscript=fatload mmc ${mmcdev} ${loadaddr} ${bootscr}
ramargs=setenv bootargs console=${console} ${optargs} mpurate=${mpurate} buddy=${buddy} camera=${camera} vram=${vram} omapfb.mode=dvi:${dvimode} omapdss.def_
disp=${defaultdisplay} root=${ramroot} rootfstype=${ramrootfstype}
loadramdisk=fatload mmc ${mmcdev} ${rdaddr} ramdisk.gz
bootscript=echo Running bootscript from mmc ...; source ${loadaddr}
loaduimage=fatload mmc ${mmcdev} ${loadaddr} uImage
mmcboot=echo Booting from mmc ...; run mmcargs; bootm ${loadaddr}
nandboot=echo Booting from nand ...; run nandargs; nand read ${loadaddr} 280000 400000; bootm ${loadaddr}
ramboot=echo Booting from ramdisk ...; run ramargs; bootm ${loadaddr}
buddy=unknown
mpurate=600
beaglerev=Cx
dieid#=42640003000000000403230911008019

Environment size: 2009/131068 bytes
OMAP3 beagleboard.org # boot
mmc1 is available
The user button is currently NOT pressed.
reading boot.scr

** Unable to read "boot.scr" from mmc 1:1 **
reading uImage

3195484 bytes read
Booting from mmc ...
## Booting kernel from Legacy Image at 80200000 ...
   Image Name:   Angstrom/2.6.32/beagleboard
   Image Type:   ARM Linux Kernel Image (uncompressed)
   Data Size:    3195420 Bytes =  3 MB
   Load Address: 80008000
   Entry Point:  80008000
   Verifying Checksum ... OK
   Loading Kernel Image ... OK
OK

Starting kernel ...

Uncompressing Linux..........................................................................................................................................
....................................................................... done, booting the kernel.
[    0.000000] Linux version 2.6.32 (koen@dominion) (gcc version 4.3.3 (GCC) ) #3 PREEMPT Thu Jan 6 17:37:46 CET 2011
[    0.000000] CPU: ARMv7 Processor [411fc083] revision 3 (ARMv7), cr=10c53c7f
[    0.000000] CPU: VIPT nonaliasing data cache, VIPT nonaliasing instruction cache
[    0.000000] Machine: OMAP3 Beagle Board
[    0.000000] Memory policy: ECC disabled, Data cache writeback
[    0.000000] OMAP3430/3530 ES3.0 (l2cache iva sgx neon isp )
[    0.000000] SRAM: Mapped pa 0x40200000 to va 0xfe400000 size: 0x100000
[    0.000000] Reserving 12582912 bytes SDRAM for VRAM
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 65024
[    0.000000] Kernel command line: console=ttyS2,115200n8 mpurate=600 buddy=unknown camera=lbcm3m1 vram=12M omapfb.mode=dvi:640x480MR-16@60 omapdss.def_disp
=dvi root=/dev/mmcblk0p2 rw rootfstype=ext3 rootwait
[    0.000000] Beagle expansionboard: unknown
[    0.000000] Beagle cameraboard: lbcm3m1
[    0.000000] PID hash table entries: 1024 (order: 0, 4096 bytes)
[    0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
[    0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
[    0.000000] Memory: 128MB 128MB = 256MB total
[    0.000000] Memory: 240384KB available (5900K code, 671K data, 204K init, 0K highmem)
[    0.000000] Hierarchical RCU implementation.
[    0.000000] NR_IRQS:402
[    0.000000] Clocking rate (Crystal/Core/MPU): 26.0/332/500 MHz
[    0.000000] Reprogramming SDRC clock to 332000000 Hz
[    0.000000] GPMC revision 5.0
[    0.000000] IRQ: Found an INTC at 0xfa200000 (revision 4.0) with 96 interrupts
[    0.000000] Total of 96 interrupts on 1 active controller
[    0.000000] OMAP GPIO hardware version 2.5
[    0.000000] OMAP clockevent source: GPTIMER12 at 32768 Hz
[    0.000000] Console: colour dummy device 80x30
[    0.000000] Calibrating delay loop... 475.76 BogoMIPS (lpj=1855488)
[    0.000000] Mount-cache hash table entries: 512
[    0.000000] CPU: Testing write buffer coherency: ok
[    0.000000] tmpfs: No value for mount option 'mode'
[    0.000000] devtmpfs: initialized
[    0.000000] regulator: core version 0.5
[    0.000000] NET: Registered protocol family 16
[    0.000000] Beagle cameraboard: registering i2c2 bus for lbcm3m1
[    0.000000] Found NAND on CS0
[    0.000000] Registering NAND on CS0
[    0.000000] Unable to get DVI reset GPIO
[    0.000000] Target VDD1 OPP = 5, VDD2 OPP = 3
[   22.891235] OMAP DMA hardware revision 4.0
[   22.900146] bio: create slab <bio-0> at 0
[   22.901763] SCSI subsystem initialized
[   22.903564] usbcore: registered new interface driver usbfs
[   22.903747] usbcore: registered new interface driver hub
[   22.903991] usbcore: registered new device driver usb
[   22.904449] i2c_omap i2c_omap.1: bus 1 rev3.12 at 2600 kHz
[   22.907623] twl4030: PIH (irq 7) chaining IRQs 368..375
[   22.907653] twl4030: power (irq 373) chaining IRQs 376..383
[   22.908050] twl4030: gpio (irq 368) chaining IRQs 384..401
[   22.909759] regulator: VUSB1V5: 1500 mV normal standby
[   22.910064] regulator: VUSB1V8: 1800 mV normal standby
[   22.910369] regulator: VUSB3V1: 3100 mV normal standby
[   22.911895] twl4030_usb twl4030_usb: Initialized TWL4030 USB module
[   22.912414] regulator: VMMC1: 1850 <--> 3150 mV normal standby
[   22.912841] regulator: VDAC: 1800 mV normal standby
[   22.913146] regulator: VPLL2: 1800 mV normal standby
[   22.913513] regulator: VSIM: 1800 <--> 3000 mV normal standby
[   22.913940] regulator: VAUX3: 1800 mV normal standby
[   22.914367] regulator: VAUX4: 1800 mV normal standby
[   22.914581] i2c_omap i2c_omap.2: bus 2 rev3.12 at 400 kHz
[   22.927551] i2c_omap i2c_omap.3: bus 3 rev3.12 at 100 kHz
[   22.929138] Switching to clocksource 32k_counter
[   22.941528] musb_hdrc: version 6.0, musb-dma, otg (peripheral+host), debug=0
[   22.944305] musb_hdrc: USB OTG mode controller at fa0ab000 using DMA, IRQ 92
[   22.944305] musb_hdrc musb_hdrc: MUSB HDRC host driver
[   22.944488] musb_hdrc musb_hdrc: new USB bus registered, assigned bus number 1
[   22.944671] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[   22.944671] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[   22.944702] usb usb1: Product: MUSB HDRC host driver
[   22.944732] usb usb1: Manufacturer: Linux 2.6.32 musb-hcd
[   22.944732] usb usb1: SerialNumber: musb_hdrc
[   22.945648] hub 1-0:1.0: USB hub found
[   22.945678] hub 1-0:1.0: 1 port detected
[   22.946990] NET: Registered protocol family 2
[   22.947265] IP route cache hash table entries: 2048 (order: 1, 8192 bytes)
[   22.947937] TCP established hash table entries: 8192 (order: 4, 65536 bytes)
[   22.948181] TCP bind hash table entries: 8192 (order: 3, 32768 bytes)
[   22.948333] TCP: Hash tables configured (established 8192 bind 8192)
[   22.948333] TCP reno registered
[   22.948364] UDP hash table entries: 256 (order: 0, 4096 bytes)
[   22.948394] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[   22.948699] NET: Registered protocol family 1
[   22.949218] RPC: Registered udp transport module.
[   22.949249] RPC: Registered tcp transport module.
[   22.949279] RPC: Registered tcp NFSv4.1 backchannel transport module.
[   22.950408] omap-iommu omap-iommu.0: isp registered
[   22.952575] VFS: Disk quotas dquot_6.5.2
[   22.952819] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[   22.954193] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[   22.955230] JFFS2 version 2.2. (NAND) (SUMMARY)  �© 2001-2006 Red Hat, Inc.
[   22.956237] msgmni has been set to 470
[   22.961730] alg: No test for stdrng (krng)
[   22.962066] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 254)
[   22.962097] io scheduler noop registered
[   22.962127] io scheduler deadline registered
[   22.962310] io scheduler cfq registered (default)
[   23.023223] OMAP DSS rev 2.0
[   23.023284] OMAP DISPC rev 3.0
[   23.023345] OMAP VENC rev 2
[   23.023651] OMAP DSI rev 1.0
[   23.364105] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
[   23.384704] serial8250.0: ttyS0 at MMIO 0x4806a000 (irq = 72) is a ST16654
[   23.404388] serial8250.1: ttyS1 at MMIO 0x4806c000 (irq = 73) is a ST16654
[   23.424011] serial8250.2: ttyS2 at MMIO 0x49020000 (irq = 74) is a ST16654
[   23.985015] console [ttyS2] enabled
[   23.997467] brd: module loaded
[   24.004913] loop: module loaded
[   24.009521] omap2-nand driver initializing
[   24.013916] NAND device: Manufacturer ID: 0x2c, Chip ID: 0xba (Micron NAND 256MiB 1,8V 16-bit)
[   24.023254] cmdlinepart partition parsing not available
[   24.028503] Creating 5 MTD partitions on "omap2-nand":
[   24.033752] 0x000000000000-0x000000080000 : "X-Loader"
[   24.040405] 0x000000080000-0x000000260000 : "U-Boot"
[   24.047149] 0x000000260000-0x000000280000 : "U-Boot Env"
[   24.053436] 0x000000280000-0x000000680000 : "Kernel"
[   24.060943] 0x000000680000-0x000010000000 : "File System"
[   24.168548] usbcore: registered new interface driver catc
[   24.174041] catc: v2.8:CATC EL1210A NetMate USB Ethernet driver
[   24.180145] usbcore: registered new interface driver kaweth
[   24.185760] pegasus: v0.6.14 (2006/09/27), Pegasus/Pegasus II USB Ethernet driver
[   24.193450] usbcore: registered new interface driver pegasus
[   24.199157] rtl8150: v0.6.2 (2004/08/27):rtl8150 based usb-ethernet driver
[   24.206207] usbcore: registered new interface driver rtl8150
[   24.212066] usbcore: registered new interface driver asix
[   24.217590] usbcore: registered new interface driver cdc_ether
[   24.223602] usbcore: registered new interface driver dm9601
[   24.229400] usbcore: registered new interface driver smsc95xx
[   24.235321] usbcore: registered new interface driver gl620a
[   24.241058] usbcore: registered new interface driver net1080
[   24.246887] usbcore: registered new interface driver plusb
[   24.252532] usbcore: registered new interface driver rndis_host
[   24.258636] usbcore: registered new interface driver cdc_subset
[   24.264709] usbcore: registered new interface driver zaurus
[   24.270446] usbcore: registered new interface driver MOSCHIP usb-ethernet driver
[   24.278747] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[   24.285614] ehci-omap ehci-omap.0: OMAP-EHCI Host Controller
[   24.291748] ehci-omap ehci-omap.0: new USB bus registered, assigned bus number 2
[   24.299438] ehci-omap ehci-omap.0: irq 77, io mem 0x48064800
[   24.319915] ehci-omap ehci-omap.0: USB 2.0 started, EHCI 1.00
[   24.325836] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002
[   24.332733] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[   24.340026] usb usb2: Product: OMAP-EHCI Host Controller
[   24.345397] usb usb2: Manufacturer: Linux 2.6.32 ehci_hcd
[   24.350860] usb usb2: SerialNumber: ehci-omap.0
[   24.356323] hub 2-0:1.0: USB hub found
[   24.360168] hub 2-0:1.0: 3 ports detected
[   24.390411] Initializing USB Mass Storage driver...
[   24.395507] usbcore: registered new interface driver usb-storage
[   24.401611] USB Mass Storage support registered.
[   24.406738] mice: PS/2 mouse device common for all mice
[   24.412445] input: gpio-keys as /devices/platform/gpio-keys/input/input0
[   24.420532] input: twl4030_pwrbutton as /devices/platform/i2c_omap.1/i2c-1/1-0049/twl4030_pwrbutton/input/input1
[   24.431365] i2c /dev entries driver
[   24.435699] Linux video capture interface: v2.00
[   24.440734] omap-iommu omap-iommu.0: isp: version 1.1
[   24.447540] vpfe_init
[   24.450531] OMAP Watchdog Timer Rev 0x31: initial timeout 60 sec
[   24.562469] mmci-omap-hs mmci-omap-hs.1: err -16 configuring card detect
[   24.569580] Registered led device: beagleboard::usr0
[   24.574768] Registered led device: beagleboard::usr1
[   24.580963] Registered led device: beagleboard::pmu_stat
[   24.588958] usbcore: registered new interface driver usbhid
[   24.594604] usbhid: USB HID core driver
[   24.598693] Advanced Linux Sound Architecture Driver Version 1.0.21.
[   24.605773] usbcore: registered new interface driver snd-usb-audio
[   24.686462] No device for DAI omap-mcbsp-dai-0
[   24.690979] No device for DAI omap-mcbsp-dai-1
[   24.695495] No device for DAI omap-mcbsp-dai-2
[   24.699981] No device for DAI omap-mcbsp-dai-3
[   24.704498] No device for DAI omap-mcbsp-dai-4
[   24.708953] OMAP3 Beagle SoC init
[   24.714111] asoc: twl4030 <-> omap-mcbsp-dai-0 mapping ok
[   24.727447] ALSA device list:
[   24.730438]   #0: omap3beagle (twl4030)
[   24.734466] oprofile: using arm/armv7
[   24.738433] TCP cubic registered
[   24.741729] NET: Registered protocol family 17
[   24.746246] NET: Registered protocol family 15
[   24.750885] lib80211: common routines for IEEE802.11 drivers
[   24.756591] ThumbEE CPU extension supported.
[   24.760925] Power Management for TI OMAP3.
[   24.766510] Switched to new clocking rate (Crystal/Core/MPU): 26.0/332/600 MHz
[   24.773834] IVA2 clocking rate: 430 MHz
[   24.960540] SmartReflex driver initialized
[   24.974060] VFP support v0.3: implementor 41 architecture 3 part 30 variant c rev 1
[   24.982604] registered taskstats version 1
[   24.988128] fbcvt: 640x480@60: CVT Name - .307M3-R
[   25.004974] Console: switching to colour frame buffer device 80x30
[   25.022247] regulator_init_complete: incomplete constraints, leaving VAUX3 on
[   25.029693] regulator_init_complete: incomplete constraints, leaving VDAC on
[   25.037353] omap_vout omap_vout: probed for an unknown device
[   25.043670] Waiting for root device /dev/mmcblk0p2...
[   25.140350] mmc0: new high speed SD card at address b368
[   25.146209] mmcblk0: mmc0:b368 SD02G 1.87 GiB
[   25.151153]  mmcblk0: p1 p2