API tools faq
paste
Advertisement
Guest User

Untitled

a guest
Dec 3rd, 2016
92
0
Never
Add comment
Not a member of Pastebin yet? Sign Up, it unlocks many cool features!
text 6.85 KB | None | 0 0
raw download clone embed print report
  1. Wiphy phy0
  2. max # scan SSIDs: 4
  3. max scan IEs length: 2257 bytes
  4. max # sched scan SSIDs: 0
  5. max # match sets: 0
  6. max # scan plans: 1
  7. max scan plan interval: -1
  8. max scan plan iterations: 0
  9. Retry short limit: 7
  10. Retry long limit: 4
  11. Coverage class: 0 (up to 0m)
  12. Device supports RSN-IBSS.
  13. Device supports AP-side u-APSD.
  14. Device supports T-DLS.
  15. Supported Ciphers:
  16. * WEP40 (00-0f-ac:1)
  17. * WEP104 (00-0f-ac:5)
  18. * TKIP (00-0f-ac:2)
  19. * CCMP-128 (00-0f-ac:4)
  20. * CCMP-256 (00-0f-ac:10)
  21. * GCMP-128 (00-0f-ac:8)
  22. * GCMP-256 (00-0f-ac:9)
  23. * CMAC (00-0f-ac:6)
  24. * CMAC-256 (00-0f-ac:13)
  25. * GMAC-128 (00-0f-ac:11)
  26. * GMAC-256 (00-0f-ac:12)
  27. Available Antennas: TX 0x1 RX 0x3
  28. Configured Antennas: TX 0x1 RX 0x3
  29. Supported interface modes:
  30. * IBSS
  31. * managed
  32. * AP
  33. * AP/VLAN
  34. * WDS
  35. * monitor
  36. * mesh point
  37. * P2P-client
  38. * P2P-GO
  39. * outside context of a BSS
  40. Band 1:
  41. Capabilities: 0x116e
  42. HT20/HT40
  43. SM Power Save disabled
  44. RX HT20 SGI
  45. RX HT40 SGI
  46. RX STBC 1-stream
  47. Max AMSDU length: 3839 bytes
  48. DSSS/CCK HT40
  49. Maximum RX AMPDU length 65535 bytes (exponent: 0x003)
  50. Minimum RX AMPDU time spacing: 8 usec (0x06)
  51. HT TX/RX MCS rate indexes supported: 0-7
  52. Bitrates (non-HT):
  53. * 1.0 Mbps
  54. * 2.0 Mbps (short preamble supported)
  55. * 5.5 Mbps (short preamble supported)
  56. * 11.0 Mbps (short preamble supported)
  57. * 6.0 Mbps
  58. * 9.0 Mbps
  59. * 12.0 Mbps
  60. * 18.0 Mbps
  61. * 24.0 Mbps
  62. * 36.0 Mbps
  63. * 48.0 Mbps
  64. * 54.0 Mbps
  65. Frequencies:
  66. * 2412 MHz [1] (16.0 dBm)
  67. * 2417 MHz [2] (16.0 dBm)
  68. * 2422 MHz [3] (16.0 dBm)
  69. * 2427 MHz [4] (16.0 dBm)
  70. * 2432 MHz [5] (16.0 dBm)
  71. * 2437 MHz [6] (16.0 dBm)
  72. * 2442 MHz [7] (16.0 dBm)
  73. * 2447 MHz [8] (16.0 dBm)
  74. * 2452 MHz [9] (16.0 dBm)
  75. * 2457 MHz [10] (16.0 dBm)
  76. * 2462 MHz [11] (16.0 dBm)
  77. * 2467 MHz [12] (16.0 dBm) (no IR)
  78. * 2472 MHz [13] (17.0 dBm) (no IR)
  79. * 2484 MHz [14] (disabled)
  80. Supported commands:
  81. * new_interface
  82. * set_interface
  83. * new_key
  84. * start_ap
  85. * new_station
  86. * new_mpath
  87. * set_mesh_config
  88. * set_bss
  89. * authenticate
  90. * associate
  91. * deauthenticate
  92. * disassociate
  93. * join_ibss
  94. * join_mesh
  95. * remain_on_channel
  96. * set_tx_bitrate_mask
  97. * frame
  98. * frame_wait_cancel
  99. * set_wiphy_netns
  100. * set_channel
  101. * set_wds_peer
  102. * tdls_mgmt
  103. * tdls_oper
  104. * probe_client
  105. * set_noack_map
  106. * register_beacons
  107. * start_p2p_device
  108. * set_mcast_rate
  109. * channel_switch
  110. * set_qos_map
  111. * connect
  112. * disconnect
  113. Supported TX frame types:
  114. * IBSS: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
  115. * managed: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
  116. * AP: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
  117. * AP/VLAN: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
  118. * mesh point: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
  119. * P2P-client: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
  120. * P2P-GO: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
  121. * P2P-device: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
  122. Supported RX frame types:
  123. * IBSS: 0x40 0xb0 0xc0 0xd0
  124. * managed: 0x40 0xd0
  125. * AP: 0x00 0x20 0x40 0xa0 0xb0 0xc0 0xd0
  126. * AP/VLAN: 0x00 0x20 0x40 0xa0 0xb0 0xc0 0xd0
  127. * mesh point: 0xb0 0xc0 0xd0
  128. * P2P-client: 0x40 0xd0
  129. * P2P-GO: 0x00 0x20 0x40 0xa0 0xb0 0xc0 0xd0
  130. * P2P-device: 0x40 0xd0
  131. software interface modes (can always be added):
  132. * AP/VLAN
  133. * monitor
  134. valid interface combinations:
  135. * #{ managed } <= 2048, #{ AP, mesh point } <= 8, #{ P2P-client, P2P-GO } <= 1,
  136. total <= 2048, #channels <= 1, STA/AP BI must match
  137. * #{ WDS } <= 2048,
  138. total <= 2048, #channels <= 1, STA/AP BI must match
  139. HT Capability overrides:
  140. * MCS: ff ff ff ff ff ff ff ff ff ff
  141. * maximum A-MSDU length
  142. * supported channel width
  143. * short GI for 40 MHz
  144. * max A-MPDU length exponent
  145. * min MPDU start spacing
  146. Device supports TX status socket option.
  147. Device supports HT-IBSS.
  148. Device supports SAE with AUTHENTICATE command
  149. Device supports low priority scan.
  150. Device supports scan flush.
  151. Device supports AP scan.
  152. Device supports per-vif TX power setting
  153. P2P GO supports CT window setting
  154. Driver supports full state transitions for AP/GO clients
  155. Driver supports a userspace MPM
  156. Device supports active monitor (which will ACK incoming frames)
  157. Driver/device bandwidth changes during BSS lifetime (AP/GO mode)
  158. Device supports configuring vdev MAC-addr on create.
Advertisement
Add Comment
Please, Sign In to add comment
Advertisement
Public Pastes
Advertisement
We use cookies for various purposes including analytics. By continuing to use Pastebin, you agree to our use of cookies as described in the Cookies Policy.  OK, I Understand
Not a member of Pastebin yet?
Sign Up, it unlocks many cool features!