Advertisement
Not a member of Pastebin yet?
Sign Up,
it unlocks many cool features!
- CFE version 1.0.37-105.22-1 for BCM96368 (32bit,SP,BE)
- Build Date: Fri Mar 19 11:53:33 CST 2010 (jojopo@broadcom_v060.comtrend.com)
- Copyright (C) 2000-2009 Broadcom Corporation.
- Parallel flash device: name AM29DL800B, id 0x22cb size 8192KB
- Total Flash size: 8192K with 135 sectors
- Chip ID: BCM6368B2, MIPS: 400MHz
- Main Thread: TP0
- Total Memory: 67108864 bytes (64MB)
- Boot Address: 0xb8000000
- Board IP address : 192.168.1.1:ffffff00
- Host IP address : 192.168.1.100
- Gateway IP address :
- Run from flash/host (f/h) : f
- Default host run file name : vmlinux
- Default host flash file name : bcm963xx_fs_kernel
- Boot delay (0-9 seconds) : 1
- Board Id (0-14) : 96368M-1341N
- Number of MAC Addresses (1-32) : 11
- Base MAC Address : 64:68:0c:
- PSI Size (1-64) KBytes : 24
- Enable Backup PSI [0|1] : 0
- System Log Size (0-256) KBytes : 0
- Main Thread Number [0|1] : 0
- *** Press any key to stop auto run (1 seconds) ***
- Auto run second count down: 110
- Booting from only image (0xb8010000) ...
- Code Address: 0x80010000, Entry Address: 0x80010000
- LZMA: Prossible old LZMA format, trying to decompress..
- Decompression OK!
- Entry at 0x80010000
- Closing network.
- Disabling Switch ports.
- Flushing Receive Buffers...
- 11 buffers found.
- Closing DMA Channels.
- Starting program at 0x80010000
- [ 0.000000] Linux version 3.10.4 (pepe@debian) (gcc version 4.6.4 (OpenWrt/Linaro GCC 4.6-2012.12 r37663) ) #6 SMP Thu Aug 8 18:37:05 CEST 2013
- [ 0.000000] Detected Broadcom 0x6368 CPU revision b2
- [ 0.000000] CPU frequency is 400 MHz
- [ 0.000000] 64MB of RAM installed
- [ 0.000000] registering 38 GPIOs
- [ 0.000000] board_bcm963xx: Boot address 0xb8000000
- [ 0.000000] board_bcm963xx: CFE version: 1.0.37-105.22-1
- [ 0.000000] bootconsole [early0] enabled
- [ 0.000000] CPU revision is: 0002a031 (Broadcom BMIPS4350)
- [ 0.000000] board_bcm963xx: board name: 96368M-1341N
- [ 0.000000] Determined physical RAM map:
- [ 0.000000] memory: 04000000 @ 00000000 (usable)
- [ 0.000000] Initrd not found or empty - disabling initrd
- [ 0.000000] Zone ranges:
- [ 0.000000] Normal [mem 0x00000000-0x03ffffff]
- [ 0.000000] Movable zone start for each node
- [ 0.000000] Early memory node ranges
- [ 0.000000] node 0: [mem 0x00000000-0x03ffffff]
- [ 0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 16 bytes.
- [ 0.000000] Primary data cache 32kB, 2-way, VIPT, cache aliases, linesize 16 bytes
- [ 0.000000] PERCPU: Embedded 7 pages/cpu @81083000 s6560 r8192 d13920 u32768
- [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 16256
- [ 0.000000] Kernel command line: root=/dev/mtdblock2 rootfstype=squashfs,jffs2 noinitrd console=ttyS0,115200
- [ 0.000000] PID hash table entries: 256 (order: -2, 1024 bytes)
- [ 0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
- [ 0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
- [ 0.000000] Memory: 61140k/65536k available (2603k kernel code, 4396k reserved, 637k data, 212k init, 0k highmem)
- [ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
- [ 0.000000] Hierarchical RCU implementation.
- [ 0.000000] NR_IRQS:128
- [ 0.000000] Calibrating delay loop... 397.82 BogoMIPS (lpj=795648)
- [ 0.032000] pid_max: default: 32768 minimum: 301
- [ 0.036000] Mount-cache hash table entries: 512
- [ 0.044000] SMP: Booting CPU1...
- [ 0.048000] CPU revision is: 0002a031 (Broadcom BMIPS4350)
- [ 0.048000] Primary instruction cache 64kB, VIPT, 4-way, linesize 16 bytes.
- [ 0.048000] Primary data cache 32kB, 2-way, VIPT, cache aliases, linesize 16 bytes
- [ 0.076000] SMP: CPU1 is running
- [ 0.076000] Brought up 2 CPUs
- [ 0.088000] NET: Registered protocol family 16
- [ 0.100000] registering PCI controller with io_map_base unset
- [ 0.116000] bio: create slab <bio-0> at 0
- [ 0.120000] PCI host bridge to bus 0000:00
- [ 0.124000] pci_bus 0000:00: root bus resource [mem 0x30000000-0x37ffffff]
- [ 0.128000] pci_bus 0000:00: root bus resource [io 0x8000000-0x800ffff]
- [ 0.132000] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff]
- [ 0.148000] pci 0000:00:01.0: BAR 0: assigned [mem 0x30000000-0x3000ffff]
- [ 0.152000] Switching to clocksource MIPS
- [ 0.164000] NET: Registered protocol family 2
- [ 0.172000] TCP established hash table entries: 512 (order: 0, 4096 bytes)
- [ 0.176000] TCP bind hash table entries: 512 (order: 0, 4096 bytes)
- [ 0.184000] TCP: Hash tables configured (established 512 bind 512)
- [ 0.192000] TCP: reno registered
- [ 0.196000] UDP hash table entries: 256 (order: 1, 8192 bytes)
- [ 0.200000] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
- [ 0.208000] NET: Registered protocol family 1
- [ 0.216000] audit: initializing netlink socket (disabled)
- [ 0.220000] type=2000 audit(0.216:1): initialized
- [ 0.248000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
- [ 0.256000] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
- [ 0.268000] msgmni has been set to 119
- [ 0.272000] io scheduler noop registered
- [ 0.276000] io scheduler cfq registered (default)
- [ 0.284000] bcm63xx_uart.0: ttyS0 at MMIO 0xb0000100 (irq = 10) is a bcm63xx_uart
- [ 0.292000] console [ttyS0] enabled, bootconsole disabled
- [ 0.292000] console [ttyS0] enabled, bootconsole disabled
- [ 0.304000] bcm63xx-rng bcm63xx-rng: registered RNG driver
- [ 0.312000] physmap platform flash device: 08000000 at 18000000
- [ 0.316000] physmap-flash.0: Found 1 x16 devices at 0x0 in 16-bit bank. Manufacturer ID 0x0000c2 Chip ID 0x0022cb
- [ 0.328000] Amd/Fujitsu Extended Query Table at 0x0040
- [ 0.336000] Amd/Fujitsu Extended Query version 1.1.
- [ 0.340000] number of CFI chips: 1
- [ 0.344000] bcm63xxpart: CFE boot tag found with version 6 and board type 96368M-1341N
- [ 0.352000] bcm63xxpart: Partition 0 is CFE offset 0 and length 10000
- [ 0.356000] bcm63xxpart: Partition 1 is kernel offset 10100 and length 12ff00
- [ 0.364000] bcm63xxpart: Partition 2 is rootfs offset 140000 and length 6b0000
- [ 0.372000] bcm63xxpart: Partition 3 is nvram offset 7f0000 and length 10000
- [ 0.380000] bcm63xxpart: Partition 4 is linux offset 10000 and length 7e0000
- [ 0.388000] bcm63xxpart: Spare partition is offset 3e0004 and length 40fffc
- [ 0.396000] 5 bcm63xxpart partitions found on MTD device physmap-flash.0
- [ 0.400000] Creating 5 MTD partitions on "physmap-flash.0":
- [ 0.408000] 0x000000000000-0x000000010000 : "CFE"
- [ 0.416000] 0x000000010100-0x000000140000 : "kernel"
- [ 0.420000] mtd: partition "kernel" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
- [ 0.436000] 0x000000140000-0x0000007f0000 : "rootfs"
- [ 0.444000] mtd: partition "rootfs" set to be root filesystem
- [ 0.448000] mtd: partition "rootfs_data" created automatically, ofs=0x3e0000, len=0x410000
- [ 0.456000] 0x0000003e0000-0x0000007f0000 : "rootfs_data"
- [ 0.464000] 0x0000007f0000-0x000000800000 : "nvram"
- [ 0.472000] 0x000000010000-0x0000007f0000 : "linux"
- [ 0.480000] bcm63xx-spi bcm63xx-spi: at 0xb0000800 (irq 9, FIFOs size 542)
- [ 0.528000] b53_common: found switch: BCM63xx, rev 0
- [ 0.532000] bcm63xx-wdt bcm63xx-wdt: started, timer margin: 30 sec
- [ 0.544000] TCP: cubic registered
- [ 0.548000] NET: Registered protocol family 17
- [ 0.552000] 8021q: 802.1Q VLAN Support v1.8
- [ 0.564000] VFS: Mounted root (squashfs filesystem) readonly on device 31:2.
- [ 0.572000] Freeing unused kernel memory: 212K (8033b000 - 80370000)
- procd: Console is alive
- procd: - watchdog -
- [ 2.660000] SCSI subsystem initialized
- [ 2.804000] usbcore: registered new interface driver usbfs
- [ 2.808000] usbcore: registered new interface driver hub
- [ 2.816000] usbcore: registered new device driver usb
- [ 2.908000] Button Hotplug driver version 0.4.1
- [ 3.512000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
- [ 3.520000] ehci-platform: EHCI generic platform driver
- [ 3.628000] ehci-platform ehci-platform: EHCI Host Controller
- [ 3.632000] ehci-platform ehci-platform: new USB bus registered, assigned bus number 1
- [ 3.640000] ehci-platform ehci-platform: irq 15, io mem 0xb0001500
- [ 3.660000] ehci-platform ehci-platform: USB 2.0 started, EHCI 1.00, overcurrent ignored
- [ 3.668000] hub 1-0:1.0: USB hub found
- [ 3.672000] hub 1-0:1.0: 2 ports detected
- [ 3.792000] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
- [ 3.796000] ohci-platform ohci-platform: Generic Platform OHCI Controller
- [ 3.804000] ohci-platform ohci-platform: new USB bus registered, assigned bus number 2
- [ 3.812000] ohci-platform ohci-platform: irq 13, io mem 0xb0001600
- [ 3.880000] hub 2-0:1.0: USB hub found
- [ 3.884000] hub 2-0:1.0: 1 port detected
- [ 4.008000] usb 1-1: new high-speed USB device number 2 using ehci-platform
- [ 4.040000] usbcore: registered new interface driver usb-storage
- [ 4.164000] input: gpio-keys-polled as /devices/platform/gpio-keys-polled.0/input/input0
- procd: - preinit -
- ifconfig: SIOCGIFFLAGS: No such device
- Press the [f] key and hit [enter] to enter failsafe mode
- mount_root: jffs2 is not ready - marker found
- ifconfig: SIOCGIFFLAGS: No such device
- procd: - early -
- procd: - watchdog -
- procd: - init -
- Please press Enter to activate this console.
- [ 10.116000] Loading modules backported from Linux version master-2013-06-27-0-gdcfa6d5
- [ 10.124000] Backport generated by backports.git backports-20130617-4-ge3220f5
- [ 10.152000] cfg80211: Calling CRDA to update world regulatory domain
- [ 10.164000] cfg80211: World regulatory domain updated:
- [ 10.168000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
- [ 10.176000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
- [ 10.184000] cfg80211: (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
- [ 10.192000] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
- [ 10.200000] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
- [ 10.208000] cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
- [ 10.456000] NET: Registered protocol family 10
- [ 11.344000] PCI: Enabling device 0000:00:01.0 (0000 -> 0002)
- [ 12.928000] cfg80211: Calling CRDA for country: AW
- [ 12.936000] cfg80211: Regulatory domain changed to country: AW
- [ 12.944000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
- [ 12.952000] cfg80211: (2402000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 2000 mBm)
- [ 12.960000] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (N/A, 2000 mBm)
- [ 12.968000] cfg80211: (5250000 KHz - 5330000 KHz @ 40000 KHz), (N/A, 2000 mBm)
- [ 12.972000] cfg80211: (5490000 KHz - 5710000 KHz @ 40000 KHz), (N/A, 2700 mBm)
- [ 12.984000] ieee80211 phy0: Atheros AR9280 Rev:2 mem=0xc0400000, irq=21
- [ 13.320000] PPP generic driver version 2.4.2
- [ 13.660000] ip_tables: (C) 2000-2006 Netfilter Core Team
- [ 13.684000] xt_time: kernel timezone is -0000
- [ 13.880000] NET: Registered protocol family 24
- [ 14.004000] nf_conntrack version 0.5.0 (958 buckets, 3832 max)
- [ 20.220000] bcm63xx_enetsw bcm63xx_enetsw.0: link UP on port2, 100Mbps, full-duplex
- [ 21.332000] bcm63xx_enetsw bcm63xx_enetsw.0: link UP on port2, 100Mbps, full-duplex
- [ 21.344000] device eth0.1 entered promiscuous mode
- [ 21.348000] device eth0 entered promiscuous mode
- [ 21.356000] br-lan: port 1(eth0.1) entered forwarding state
- [ 21.364000] br-lan: port 1(eth0.1) entered forwarding state
- [ 23.368000] br-lan: port 1(eth0.1) entered forwarding state
- [ 32.720000] jffs2_scan_eraseblock(): End of filesystem marker found at 0x0
- [ 32.740000] jffs2_build_filesystem(): unlocking the mtd device... done.
- [ 32.744000] jffs2_build_filesystem(): erasing all blocks after the end marker... done.
- [ 67.332000] jffs2: notice: (902) jffs2_build_xattr_subsystem: complete building xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0 orphan) found.
- procd: - init complete -
- dmesg
- BusyBox v1.19.4 (2013-08-08 17:47:34 CEST) built-in shell (ash)
- Enter 'help' for a list of built-in commands.
- _______ ________ __
- | |.-----.-----.-----.| | | |.----.| |_
- | - || _ | -__| || | | || _|| _|
- |_______|| __|_____|__|__||________||__| |____|
- |__| W I R E L E S S F R E E D O M
- -----------------------------------------------------
- BARÒR (Bleeding Edge, r37737)
- -----------------------------------------------------
- * 1/2 oz Galliano Pour all ingredients into
- * 4 oz cold Coffee an irish coffee mug filled
- * 1 1/2 oz Dark Rum with crushed ice. Stir.
- * 2 tsp. Creme de Cacao
- -----------------------------------------------------
- root@OpenWrt:/# dmesg
- [ 0.000000] Linux version 3.10.4 (pepe@debian) (gcc version 4.6.4 (OpenWrt/Linaro GCC 4.6-2012.12 r37663) ) #6 SMP Thu Aug 8 18:37:05 CEST 2013
- [ 0.000000] Detected Broadcom 0x6368 CPU revision b2
- [ 0.000000] CPU frequency is 400 MHz
- [ 0.000000] 64MB of RAM installed
- [ 0.000000] registering 38 GPIOs
- [ 0.000000] board_bcm963xx: Boot address 0xb8000000
- [ 0.000000] board_bcm963xx: CFE version: 1.0.37-105.22-1
- [ 0.000000] bootconsole [early0] enabled
- [ 0.000000] CPU revision is: 0002a031 (Broadcom BMIPS4350)
- [ 0.000000] board_bcm963xx: board name: 96368M-1341N
- [ 0.000000] Determined physical RAM map:
- [ 0.000000] memory: 04000000 @ 00000000 (usable)
- [ 0.000000] Initrd not found or empty - disabling initrd
- [ 0.000000] Zone ranges:
- [ 0.000000] Normal [mem 0x00000000-0x03ffffff]
- [ 0.000000] Movable zone start for each node
- [ 0.000000] Early memory node ranges
- [ 0.000000] node 0: [mem 0x00000000-0x03ffffff]
- [ 0.000000] On node 0 totalpages: 16384
- [ 0.000000] free_area_init_node: node 0, pgdat 803269e0, node_mem_map 81000000
- [ 0.000000] Normal zone: 128 pages used for memmap
- [ 0.000000] Normal zone: 0 pages reserved
- [ 0.000000] Normal zone: 16384 pages, LIFO batch:3
- [ 0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 16 bytes.
- [ 0.000000] Primary data cache 32kB, 2-way, VIPT, cache aliases, linesize 16 bytes
- [ 0.000000] PERCPU: Embedded 7 pages/cpu @81083000 s6560 r8192 d13920 u32768
- [ 0.000000] pcpu-alloc: s6560 r8192 d13920 u32768 alloc=8*4096
- [ 0.000000] pcpu-alloc: [0] 0 [0] 1
- [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 16256
- [ 0.000000] Kernel command line: root=/dev/mtdblock2 rootfstype=squashfs,jffs2 noinitrd console=ttyS0,115200
- [ 0.000000] PID hash table entries: 256 (order: -2, 1024 bytes)
- [ 0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
- [ 0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
- [ 0.000000] Memory: 61140k/65536k available (2603k kernel code, 4396k reserved, 637k data, 212k init, 0k highmem)
- [ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
- [ 0.000000] Hierarchical RCU implementation.
- [ 0.000000] NR_IRQS:128
- [ 0.028000] Calibrating delay loop... 397.82 BogoMIPS (lpj=795648)
- [ 0.032000] pid_max: default: 32768 minimum: 301
- [ 0.036000] Mount-cache hash table entries: 512
- [ 0.044000] SMP: Booting CPU1...
- [ 0.048000] CPU revision is: 0002a031 (Broadcom BMIPS4350)
- [ 0.048000] Primary instruction cache 64kB, VIPT, 4-way, linesize 16 bytes.
- [ 0.048000] Primary data cache 32kB, 2-way, VIPT, cache aliases, linesize 16 bytes
- [ 0.076000] SMP: CPU1 is running
- [ 0.076000] Brought up 2 CPUs
- [ 0.076000] device: 'platform': device_add
- [ 0.076000] bus: 'platform': registered
- [ 0.076000] bus: 'cpu': registered
- [ 0.076000] device: 'cpu': device_add
- [ 0.088000] bus: 'workqueue': registered
- [ 0.088000] device: 'workqueue': device_add
- [ 0.088000] NET: Registered protocol family 16
- [ 0.088000] device class 'bdi': registering
- [ 0.088000] device class 'gpio': registering
- [ 0.088000] device: 'gpiochip0': device_add
- [ 0.088000] device class 'pci_bus': registering
- [ 0.092000] bus: 'pci': registered
- [ 0.092000] device class 'tty': registering
- [ 0.092000] bus: 'spi': registered
- [ 0.092000] device class 'spi_master': registering
- [ 0.092000] Registering platform device 'bcm63xx_uart.0'. Parent at platform
- [ 0.092000] device: 'bcm63xx_uart.0': device_add
- [ 0.092000] bus: 'platform': add device bcm63xx_uart.0
- [ 0.092000] Registering platform device 'bcm63xx_enet_shared.0'. Parent at platform
- [ 0.092000] device: 'bcm63xx_enet_shared.0': device_add
- [ 0.092000] bus: 'platform': add device bcm63xx_enet_shared.0
- [ 0.092000] Registering platform device 'bcm63xx_enetsw.0'. Parent at platform
- [ 0.092000] device: 'bcm63xx_enetsw.0': device_add
- [ 0.092000] bus: 'platform': add device bcm63xx_enetsw.0
- [ 0.096000] Registering platform device 'ehci-platform'. Parent at platform
- [ 0.096000] device: 'ehci-platform': device_add
- [ 0.096000] bus: 'platform': add device ehci-platform
- [ 0.096000] Registering platform device 'ohci-platform'. Parent at platform
- [ 0.096000] device: 'ohci-platform': device_add
- [ 0.096000] bus: 'platform': add device ohci-platform
- [ 0.096000] Registering platform device 'bcm63xx-spi'. Parent at platform
- [ 0.096000] device: 'bcm63xx-spi': device_add
- [ 0.096000] bus: 'platform': add device bcm63xx-spi
- [ 0.096000] Registering platform device 'physmap-flash.0'. Parent at platform
- [ 0.096000] device: 'physmap-flash.0': device_add
- [ 0.096000] bus: 'platform': add device physmap-flash.0
- [ 0.096000] Registering platform device 'leds-gpio.0'. Parent at platform
- [ 0.096000] device: 'leds-gpio.0': device_add
- [ 0.096000] bus: 'platform': add device leds-gpio.0
- [ 0.096000] Registering platform device 'gpio-keys-polled.0'. Parent at platform
- [ 0.096000] device: 'gpio-keys-polled.0': device_add
- [ 0.096000] bus: 'platform': add device gpio-keys-polled.0
- [ 0.096000] Registering platform device 'bcm63xx-rng'. Parent at platform
- [ 0.096000] device: 'bcm63xx-rng': device_add
- [ 0.096000] bus: 'platform': add device bcm63xx-rng
- [ 0.100000] Registering platform device 'bcm63xx-wdt'. Parent at platform
- [ 0.100000] device: 'bcm63xx-wdt': device_add
- [ 0.100000] bus: 'platform': add device bcm63xx-wdt
- [ 0.100000] registering PCI controller with io_map_base unset
- [ 0.100000] device: 'cpu0': device_add
- [ 0.100000] bus: 'cpu': add device cpu0
- [ 0.100000] device: 'cpu1': device_add
- [ 0.100000] bus: 'cpu': add device cpu1
- [ 0.116000] device: 'writeback': device_add
- [ 0.116000] bus: 'workqueue': add device writeback
- [ 0.116000] device: 'default': device_add
- [ 0.116000] bio: create slab <bio-0> at 0
- [ 0.120000] device class 'block': registering
- [ 0.120000] device class 'misc': registering
- [ 0.120000] device class 'mdio_bus': registering
- [ 0.120000] bus: 'mdio_bus': registered
- [ 0.120000] bus: 'mdio_bus': add driver Generic PHY
- [ 0.120000] device class 'leds': registering
- [ 0.120000] device: 'pci0000:00': device_add
- [ 0.120000] device: '0000:00': device_add
- [ 0.120000] PCI host bridge to bus 0000:00
- [ 0.124000] pci_bus 0000:00: root bus resource [mem 0x30000000-0x37ffffff]
- [ 0.128000] pci_bus 0000:00: root bus resource [io 0x8000000-0x800ffff]
- [ 0.132000] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff]
- [ 0.136000] pci 0000:00:01.0: [168c:0029] type 00 class 0x028000
- [ 0.136000] pci 0000:00:01.0: reg 10: [mem 0x00000000-0x0000ffff]
- [ 0.148000] pci 0000:00:01.0: PME# supported from D0 D3hot
- [ 0.148000] device: '0000:00:01.0': device_add
- [ 0.148000] bus: 'pci': add device 0000:00:01.0
- [ 0.148000] pci_bus 0000:00: busn_res: [bus 00-ff] end is updated to 00
- [ 0.148000] pci 0000:00:01.0: BAR 0: assigned [mem 0x30000000-0x3000ffff]
- [ 0.152000] device class 'net': registering
- [ 0.152000] device: 'lo': device_add
- [ 0.152000] Switching to clocksource MIPS
- [ 0.156000] device class 'mem': registering
- [ 0.156000] device: 'mem': device_add
- [ 0.156000] device: 'null': device_add
- [ 0.156000] device: 'port': device_add
- [ 0.156000] device: 'zero': device_add
- [ 0.156000] device: 'full': device_add
- [ 0.156000] device: 'random': device_add
- [ 0.160000] device: 'urandom': device_add
- [ 0.164000] device: 'kmsg': device_add
- [ 0.164000] device: 'tty': device_add
- [ 0.164000] device: 'console': device_add
- [ 0.164000] device class 'firmware': registering
- [ 0.164000] bus: 'ssb': registered
- [ 0.164000] bus: 'pci': add driver b43-pci-bridge
- [ 0.164000] NET: Registered protocol family 2
- [ 0.172000] TCP established hash table entries: 512 (order: 0, 4096 bytes)
- [ 0.176000] TCP bind hash table entries: 512 (order: 0, 4096 bytes)
- [ 0.184000] TCP: Hash tables configured (established 512 bind 512)
- [ 0.192000] TCP: reno registered
- [ 0.196000] UDP hash table entries: 256 (order: 1, 8192 bytes)
- [ 0.200000] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
- [ 0.208000] NET: Registered protocol family 1
- [ 0.212000] PCI: CLS 0 bytes, default 16
- [ 0.212000] bus: 'clocksource': registered
- [ 0.212000] device: 'clocksource': device_add
- [ 0.212000] device: 'clocksource0': device_add
- [ 0.212000] bus: 'clocksource': add device clocksource0
- [ 0.212000] bus: 'platform': add driver alarmtimer
- [ 0.216000] Registering platform device 'alarmtimer'. Parent at platform
- [ 0.216000] device: 'alarmtimer': device_add
- [ 0.216000] bus: 'platform': add device alarmtimer
- [ 0.216000] bus: 'platform': driver_probe_device: matched device alarmtimer with driver alarmtimer
- [ 0.216000] bus: 'platform': really_probe: probing driver alarmtimer with device alarmtimer
- [ 0.216000] driver: 'alarmtimer': driver_bound: bound to device 'alarmtimer'
- [ 0.216000] bus: 'platform': really_probe: bound device alarmtimer to driver alarmtimer
- [ 0.216000] audit: initializing netlink socket (disabled)
- [ 0.220000] type=2000 audit(0.216:1): initialized
- [ 0.248000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
- [ 0.256000] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
- [ 0.268000] msgmni has been set to 119
- [ 0.272000] io scheduler noop registered
- [ 0.276000] io scheduler cfq registered (default)
- [ 0.280000] device: 'ptmx': device_add
- [ 0.284000] bus: 'platform': add driver bcm63xx_uart
- [ 0.284000] bus: 'platform': driver_probe_device: matched device bcm63xx_uart.0 with driver bcm63xx_uart
- [ 0.284000] bus: 'platform': really_probe: probing driver bcm63xx_uart with device bcm63xx_uart.0
- [ 0.284000] bcm63xx_uart.0: ttyS0 at MMIO 0xb0000100 (irq = 10) is a bcm63xx_uart
- [ 0.292000] console [ttyS0] enabled, bootconsole disabled
- [ 0.300000] device: 'ttyS0': device_add
- [ 0.300000] driver: 'bcm63xx_uart.0': driver_bound: bound to device 'bcm63xx_uart'
- [ 0.300000] bus: 'platform': really_probe: bound device bcm63xx_uart.0 to driver bcm63xx_uart
- [ 0.304000] bus: 'platform': add driver bcm63xx-rng
- [ 0.304000] bus: 'platform': driver_probe_device: matched device bcm63xx-rng with driver bcm63xx-rng
- [ 0.304000] bus: 'platform': really_probe: probing driver bcm63xx-rng with device bcm63xx-rng
- [ 0.304000] device: 'hw_random': device_add
- [ 0.304000] bcm63xx-rng bcm63xx-rng: registered RNG driver
- [ 0.308000] driver: 'bcm63xx-rng': driver_bound: bound to device 'bcm63xx-rng'
- [ 0.308000] bus: 'platform': really_probe: bound device bcm63xx-rng to driver bcm63xx-rng
- [ 0.308000] device class 'mtd': registering
- [ 0.308000] device: 'mtd-unmap': device_add
- [ 0.312000] device: 'mtd-romap': device_add
- [ 0.312000] device: 'mtd-rwmap': device_add
- [ 0.312000] bus: 'platform': add driver physmap-flash
- [ 0.312000] bus: 'platform': driver_probe_device: matched device physmap-flash.0 with driver physmap-flash
- [ 0.312000] bus: 'platform': really_probe: probing driver physmap-flash with device physmap-flash.0
- [ 0.312000] physmap platform flash device: 08000000 at 18000000
- [ 0.316000] physmap-flash.0: Found 1 x16 devices at 0x0 in 16-bit bank. Manufacturer ID 0x0000c2 Chip ID 0x0022cb
- [ 0.328000] physmap-flash.0: Found an alias at 0x800000 for the chip at 0x0
- [ 0.328000] physmap-flash.0: Found an alias at 0x1000000 for the chip at 0x0
- [ 0.328000] physmap-flash.0: Found an alias at 0x1800000 for the chip at 0x0
- [ 0.328000] Amd/Fujitsu Extended Query Table at 0x0040
- [ 0.336000] Amd/Fujitsu Extended Query version 1.1.
- [ 0.340000] number of CFI chips: 1
- [ 0.344000] bcm63xxpart: CFE boot tag found with version 6 and board type 96368M-1341N
- [ 0.352000] bcm63xxpart: Partition 0 is CFE offset 0 and length 10000
- [ 0.356000] bcm63xxpart: Partition 1 is kernel offset 10100 and length 12ff00
- [ 0.364000] bcm63xxpart: Partition 2 is rootfs offset 140000 and length 6b0000
- [ 0.372000] bcm63xxpart: Partition 3 is nvram offset 7f0000 and length 10000
- [ 0.380000] bcm63xxpart: Partition 4 is linux offset 10000 and length 7e0000
- [ 0.388000] bcm63xxpart: Spare partition is offset 3e0004 and length 40fffc
- [ 0.396000] 5 bcm63xxpart partitions found on MTD device physmap-flash.0
- [ 0.400000] Creating 5 MTD partitions on "physmap-flash.0":
- [ 0.408000] 0x000000000000-0x000000010000 : "CFE"
- [ 0.412000] device: 'mtd0': device_add
- [ 0.412000] device: 'mtd0ro': device_add
- [ 0.412000] device: '31:0': device_add
- [ 0.412000] device: 'mtdblock0': device_add
- [ 0.416000] 0x000000010100-0x000000140000 : "kernel"
- [ 0.420000] mtd: partition "kernel" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
- [ 0.432000] device: 'mtd1': device_add
- [ 0.432000] device: 'mtd1ro': device_add
- [ 0.436000] device: '31:1': device_add
- [ 0.436000] device: 'mtdblock1': device_add
- [ 0.436000] 0x000000140000-0x0000007f0000 : "rootfs"
- [ 0.440000] device: 'mtd2': device_add
- [ 0.440000] device: 'mtd2ro': device_add
- [ 0.440000] device: '31:2': device_add
- [ 0.444000] device: 'mtdblock2': device_add
- [ 0.444000] mtd: partition "rootfs" set to be root filesystem
- [ 0.448000] mtd: partition "rootfs_data" created automatically, ofs=0x3e0000, len=0x410000
- [ 0.456000] 0x0000003e0000-0x0000007f0000 : "rootfs_data"
- [ 0.464000] device: 'mtd3': device_add
- [ 0.464000] device: 'mtd3ro': device_add
- [ 0.464000] device: '31:3': device_add
- [ 0.464000] device: 'mtdblock3': device_add
- [ 0.464000] 0x0000007f0000-0x000000800000 : "nvram"
- [ 0.472000] device: 'mtd4': device_add
- [ 0.472000] device: 'mtd4ro': device_add
- [ 0.472000] device: '31:4': device_add
- [ 0.472000] device: 'mtdblock4': device_add
- [ 0.472000] 0x000000010000-0x0000007f0000 : "linux"
- [ 0.480000] device: 'mtd5': device_add
- [ 0.480000] device: 'mtd5ro': device_add
- [ 0.480000] device: '31:5': device_add
- [ 0.480000] device: 'mtdblock5': device_add
- [ 0.480000] driver: 'physmap-flash.0': driver_bound: bound to device 'physmap-flash'
- [ 0.480000] bus: 'platform': really_probe: bound device physmap-flash.0 to driver physmap-flash
- [ 0.480000] bus: 'platform': add driver bcm63xx-spi
- [ 0.480000] bus: 'platform': driver_probe_device: matched device bcm63xx-spi with driver bcm63xx-spi
- [ 0.480000] bus: 'platform': really_probe: probing driver bcm63xx-spi with device bcm63xx-spi
- [ 0.480000] device: 'spi0': device_add
- [ 0.480000] bcm63xx-spi bcm63xx-spi: at 0xb0000800 (irq 9, FIFOs size 542)
- [ 0.488000] driver: 'bcm63xx-spi': driver_bound: bound to device 'bcm63xx-spi'
- [ 0.488000] bus: 'platform': really_probe: bound device bcm63xx-spi to driver bcm63xx-spi
- [ 0.488000] bus: 'platform': add driver bcm63xx-hsspi
- [ 0.488000] bus: 'platform': add driver spi_gpio
- [ 0.492000] bus: 'mdio_bus': add driver Broadcom BCM63XX (1)
- [ 0.492000] bus: 'mdio_bus': add driver Broadcom BCM63XX (2)
- [ 0.492000] bus: 'platform': add driver b53-switch
- [ 0.492000] bus: 'mdio_bus': add driver Broadcom B53 (1)
- [ 0.492000] bus: 'mdio_bus': add driver Broadcom B53 (2)
- [ 0.492000] bus: 'spi': add driver b53-switch
- [ 0.492000] bus: 'platform': add driver bcm63xx_enet_shared
- [ 0.492000] bus: 'platform': driver_probe_device: matched device bcm63xx_enet_shared.0 with driver bcm63xx_enet_shared
- [ 0.492000] bus: 'platform': really_probe: probing driver bcm63xx_enet_shared with device bcm63xx_enet_shared.0
- [ 0.492000] driver: 'bcm63xx_enet_shared.0': driver_bound: bound to device 'bcm63xx_enet_shared'
- [ 0.492000] bus: 'platform': really_probe: bound device bcm63xx_enet_shared.0 to driver bcm63xx_enet_shared
- [ 0.492000] bus: 'platform': add driver bcm63xx_enet
- [ 0.492000] bus: 'platform': add driver bcm63xx_enetsw
- [ 0.492000] bus: 'platform': driver_probe_device: matched device bcm63xx_enetsw.0 with driver bcm63xx_enetsw
- [ 0.492000] bus: 'platform': really_probe: probing driver bcm63xx_enetsw with device bcm63xx_enetsw.0
- [ 0.524000] device: 'eth0': device_add
- [ 0.524000] Registering platform device 'b53-switch'. Parent at platform
- [ 0.524000] device: 'b53-switch': device_add
- [ 0.524000] bus: 'platform': add device b53-switch
- [ 0.528000] bus: 'platform': driver_probe_device: matched device b53-switch with driver b53-switch
- [ 0.528000] bus: 'platform': really_probe: probing driver b53-switch with device b53-switch
- [ 0.528000] b53_common: found switch: BCM63xx, rev 0
- [ 0.532000] driver: 'b53-switch': driver_bound: bound to device 'b53-switch'
- [ 0.532000] bus: 'platform': really_probe: bound device b53-switch to driver b53-switch
- [ 0.532000] driver: 'bcm63xx_enetsw.0': driver_bound: bound to device 'bcm63xx_enetsw'
- [ 0.532000] bus: 'platform': really_probe: bound device bcm63xx_enetsw.0 to driver bcm63xx_enetsw
- [ 0.532000] bus: 'platform': add driver bcm63xx-wdt
- [ 0.532000] bus: 'platform': driver_probe_device: matched device bcm63xx-wdt with driver bcm63xx-wdt
- [ 0.532000] bus: 'platform': really_probe: probing driver bcm63xx-wdt with device bcm63xx-wdt
- [ 0.532000] device: 'watchdog': device_add
- [ 0.532000] bcm63xx-wdt bcm63xx-wdt: started, timer margin: 30 sec
- [ 0.540000] driver: 'bcm63xx-wdt': driver_bound: bound to device 'bcm63xx-wdt'
- [ 0.540000] bus: 'platform': really_probe: bound device bcm63xx-wdt to driver bcm63xx-wdt
- [ 0.540000] bus: 'platform': add driver leds-gpio
- [ 0.540000] bus: 'platform': driver_probe_device: matched device leds-gpio.0 with driver leds-gpio
- [ 0.540000] bus: 'platform': really_probe: probing driver leds-gpio with device leds-gpio.0
- [ 0.540000] device: 'VR-3025un:green:dsl': device_add
- [ 0.540000] device: 'VR-3025un:green:inet': device_add
- [ 0.540000] device: 'VR-3025un:green:power': device_add
- [ 0.544000] device: 'VR-3025un:red:power': device_add
- [ 0.544000] device: 'VR-3025un:red:inet': device_add
- [ 0.544000] driver: 'leds-gpio.0': driver_bound: bound to device 'leds-gpio'
- [ 0.544000] bus: 'platform': really_probe: bound device leds-gpio.0 to driver leds-gpio
- [ 0.544000] TCP: cubic registered
- [ 0.548000] NET: Registered protocol family 17
- [ 0.552000] 8021q: 802.1Q VLAN Support v1.8
- [ 0.556000] device: 'cpu_dma_latency': device_add
- [ 0.556000] device: 'network_latency': device_add
- [ 0.556000] device: 'network_throughput': device_add
- [ 0.564000] VFS: Mounted root (squashfs filesystem) readonly on device 31:2.
- [ 0.572000] Freeing unused kernel memory: 212K (8033b000 - 80370000)
- [ 2.204000] device class 'input': registering
- [ 2.660000] device class 'scsi_host': registering
- [ 2.660000] bus: 'scsi': registered
- [ 2.660000] device class 'scsi_device': registering
- [ 2.660000] SCSI subsystem initialized
- [ 2.804000] bus: 'usb': registered
- [ 2.804000] bus: 'usb': add driver usbfs
- [ 2.804000] usbcore: registered new interface driver usbfs
- [ 2.808000] bus: 'usb': add driver hub
- [ 2.808000] usbcore: registered new interface driver hub
- [ 2.816000] bus: 'usb': add driver usb
- [ 2.816000] usbcore: registered new device driver usb
- [ 2.908000] Button Hotplug driver version 0.4.1
- [ 3.500000] device class 'scsi_disk': registering
- [ 3.504000] bus: 'scsi': add driver sd
- [ 3.512000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
- [ 3.520000] ehci-platform: EHCI generic platform driver
- [ 3.524000] bus: 'platform': add driver ehci-platform
- [ 3.524000] bus: 'platform': driver_probe_device: matched device ehci-platform with driver ehci-platform
- [ 3.524000] bus: 'platform': really_probe: probing driver ehci-platform with device ehci-platform
- [ 3.628000] ehci-platform ehci-platform: EHCI Host Controller
- [ 3.632000] ehci-platform ehci-platform: new USB bus registered, assigned bus number 1
- [ 3.640000] ehci-platform ehci-platform: irq 15, io mem 0xb0001500
- [ 3.660000] ehci-platform ehci-platform: USB 2.0 started, EHCI 1.00, overcurrent ignored
- [ 3.668000] device: 'usb1': device_add
- [ 3.668000] bus: 'usb': add device usb1
- [ 3.668000] bus: 'usb': driver_probe_device: matched device usb1 with driver usb
- [ 3.668000] bus: 'usb': really_probe: probing driver usb with device usb1
- [ 3.668000] device: '1-0:1.0': device_add
- [ 3.668000] bus: 'usb': add device 1-0:1.0
- [ 3.668000] bus: 'usb': driver_probe_device: matched device 1-0:1.0 with driver hub
- [ 3.668000] bus: 'usb': really_probe: probing driver hub with device 1-0:1.0
- [ 3.668000] hub 1-0:1.0: USB hub found
- [ 3.672000] hub 1-0:1.0: 2 ports detected
- [ 3.676000] device: 'port1': device_add
- [ 3.676000] device: 'port2': device_add
- [ 3.676000] driver: '1-0:1.0': driver_bound: bound to device 'hub'
- [ 3.676000] bus: 'usb': really_probe: bound device 1-0:1.0 to driver hub
- [ 3.676000] device: 'ep_81': device_add
- [ 3.676000] driver: 'usb1': driver_bound: bound to device 'usb'
- [ 3.676000] bus: 'usb': really_probe: bound device usb1 to driver usb
- [ 3.676000] device: 'ep_00': device_add
- [ 3.676000] driver: 'ehci-platform': driver_bound: bound to device 'ehci-platform'
- [ 3.676000] bus: 'platform': really_probe: bound device ehci-platform to driver ehci-platform
- [ 3.792000] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
- [ 3.796000] bus: 'platform': add driver ohci-platform
- [ 3.796000] bus: 'platform': driver_probe_device: matched device ohci-platform with driver ohci-platform
- [ 3.796000] bus: 'platform': really_probe: probing driver ohci-platform with device ohci-platform
- [ 3.796000] ohci-platform ohci-platform: Generic Platform OHCI Controller
- [ 3.804000] ohci-platform ohci-platform: new USB bus registered, assigned bus number 2
- [ 3.812000] ohci-platform ohci-platform: irq 13, io mem 0xb0001600
- [ 3.880000] device: 'usb2': device_add
- [ 3.880000] bus: 'usb': add device usb2
- [ 3.880000] bus: 'usb': driver_probe_device: matched device usb2 with driver usb
- [ 3.880000] bus: 'usb': really_probe: probing driver usb with device usb2
- [ 3.880000] device: '2-0:1.0': device_add
- [ 3.880000] bus: 'usb': add device 2-0:1.0
- [ 3.880000] bus: 'usb': driver_probe_device: matched device 2-0:1.0 with driver hub
- [ 3.880000] bus: 'usb': really_probe: probing driver hub with device 2-0:1.0
- [ 3.880000] hub 2-0:1.0: USB hub found
- [ 3.884000] hub 2-0:1.0: 1 port detected
- [ 3.888000] device: 'port1': device_add
- [ 3.888000] driver: '2-0:1.0': driver_bound: bound to device 'hub'
- [ 3.888000] bus: 'usb': really_probe: bound device 2-0:1.0 to driver hub
- [ 3.888000] device: 'ep_81': device_add
- [ 3.888000] driver: 'usb2': driver_bound: bound to device 'usb'
- [ 3.888000] bus: 'usb': really_probe: bound device usb2 to driver usb
- [ 3.888000] device: 'ep_00': device_add
- [ 3.888000] driver: 'ohci-platform': driver_bound: bound to device 'ohci-platform'
- [ 3.888000] bus: 'platform': really_probe: bound device ohci-platform to driver ohci-platform
- [ 3.888000] bus: 'pci': add driver ohci_hcd
- [ 4.008000] usb 1-1: new high-speed USB device number 2 using ehci-platform
- [ 4.040000] bus: 'usb': add driver usb-storage
- [ 4.040000] usbcore: registered new interface driver usb-storage
- [ 4.164000] bus: 'platform': add driver gpio-keys-polled
- [ 4.164000] bus: 'platform': driver_probe_device: matched device gpio-keys-polled.0 with driver gpio-keys-polled
- [ 4.164000] bus: 'platform': really_probe: probing driver gpio-keys-polled with device gpio-keys-polled.0
- [ 4.164000] device: 'input0': device_add
- [ 4.164000] input: gpio-keys-polled as /devices/platform/gpio-keys-polled.0/input/input0
- [ 4.172000] driver: 'gpio-keys-polled.0': driver_bound: bound to device 'gpio-keys-polled'
- [ 4.172000] bus: 'platform': really_probe: bound device gpio-keys-polled.0 to driver gpio-keys-polled
- [ 9.144000] device: '1-1': device_add
- [ 9.144000] bus: 'usb': add device 1-1
- [ 9.156000] bus: 'usb': driver_probe_device: matched device 1-1 with driver usb
- [ 9.156000] bus: 'usb': really_probe: probing driver usb with device 1-1
- [ 9.156000] device: '1-1:1.0': device_add
- [ 9.156000] bus: 'usb': add device 1-1:1.0
- [ 9.156000] device: 'ep_83': device_add
- [ 9.156000] device: 'ep_04': device_add
- [ 9.156000] device: 'ep_05': device_add
- [ 9.156000] device: 'ep_06': device_add
- [ 9.156000] device: 'ep_07': device_add
- [ 9.160000] device: 'ep_89': device_add
- [ 9.160000] device: 'ep_0a': device_add
- [ 9.160000] device: 'ep_0b': device_add
- [ 9.160000] device: 'ep_0c': device_add
- [ 9.160000] driver: '1-1': driver_bound: bound to device 'usb'
- [ 9.160000] bus: 'usb': really_probe: bound device 1-1 to driver usb
- [ 9.160000] device: 'ep_00': device_add
- [ 10.116000] Loading modules backported from Linux version master-2013-06-27-0-gdcfa6d5
- [ 10.124000] Backport generated by backports.git backports-20130617-4-ge3220f5
- [ 10.152000] device class 'ieee80211': registering
- [ 10.152000] Registering platform device 'regulatory.0'. Parent at platform
- [ 10.152000] device: 'regulatory.0': device_add
- [ 10.152000] bus: 'platform': add device regulatory.0
- [ 10.152000] cfg80211: Calling CRDA to update world regulatory domain
- [ 10.164000] cfg80211: World regulatory domain updated:
- [ 10.168000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
- [ 10.176000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
- [ 10.184000] cfg80211: (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
- [ 10.192000] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
- [ 10.200000] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
- [ 10.208000] cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
- [ 10.456000] NET: Registered protocol family 10
- [ 11.344000] bus: 'pci': add driver ath9k
- [ 11.344000] bus: 'pci': driver_probe_device: matched device 0000:00:01.0 with driver ath9k
- [ 11.344000] bus: 'pci': really_probe: probing driver ath9k with device 0000:00:01.0
- [ 11.344000] PCI: Enabling device 0000:00:01.0 (0000 -> 0002)
- [ 12.912000] ath: EEPROM regdomain: 0x37
- [ 12.912000] ath: EEPROM indicates we should expect a direct regpair map
- [ 12.912000] ath: Country alpha2 being used: AW
- [ 12.912000] ath: Regpair used: 0x37
- [ 12.920000] device: 'phy0': device_add
- [ 12.920000] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'
- [ 12.920000] device: 'wlan0': device_add
- [ 12.928000] device: 'ath9k-phy0': device_add
- [ 12.928000] cfg80211: Calling CRDA for country: AW
- [ 12.936000] cfg80211: Regulatory domain changed to country: AW
- [ 12.944000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
- [ 12.952000] cfg80211: (2402000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 2000 mBm)
- [ 12.960000] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (N/A, 2000 mBm)
- [ 12.968000] cfg80211: (5250000 KHz - 5330000 KHz @ 40000 KHz), (N/A, 2000 mBm)
- [ 12.972000] cfg80211: (5490000 KHz - 5710000 KHz @ 40000 KHz), (N/A, 2700 mBm)
- [ 12.984000] ieee80211 phy0: Atheros AR9280 Rev:2 mem=0xc0400000, irq=21
- [ 12.988000] driver: '0000:00:01.0': driver_bound: bound to device 'ath9k'
- [ 12.988000] bus: 'pci': really_probe: bound device 0000:00:01.0 to driver ath9k
- [ 13.320000] PPP generic driver version 2.4.2
- [ 13.324000] device class 'ppp': registering
- [ 13.324000] device: 'ppp': device_add
- [ 13.660000] ip_tables: (C) 2000-2006 Netfilter Core Team
- [ 13.684000] xt_time: kernel timezone is -0000
- [ 13.880000] NET: Registered protocol family 24
- [ 14.004000] nf_conntrack version 0.5.0 (958 buckets, 3832 max)
- [ 20.220000] bcm63xx_enetsw bcm63xx_enetsw.0: link UP on port2, 100Mbps, full-duplex
- [ 21.324000] device: 'br-lan': device_add
- [ 21.328000] device: 'eth0.1': device_add
- [ 21.332000] bcm63xx_enetsw bcm63xx_enetsw.0: link UP on port2, 100Mbps, full-duplex
- [ 21.344000] device eth0.1 entered promiscuous mode
- [ 21.348000] device eth0 entered promiscuous mode
- [ 21.356000] br-lan: port 1(eth0.1) entered forwarding state
- [ 21.364000] br-lan: port 1(eth0.1) entered forwarding state
- [ 23.368000] br-lan: port 1(eth0.1) entered forwarding state
- [ 32.720000] jffs2_scan_eraseblock(): End of filesystem marker found at 0x0
- [ 32.740000] jffs2_build_filesystem(): unlocking the mtd device... done.
- [ 32.744000] jffs2_build_filesystem(): erasing all blocks after the end marker... done.
- [ 67.332000] jffs2: notice: (902) jffs2_build_xattr_subsystem: complete building xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0 orphan) found.
- root@OpenWrt:/#
- root@OpenWrt:/# lsusb
- Bus 001 Device 002: ID 0bda:8187 Realtek Semiconductor Corp. RTL8187 Wireless Adapter
- Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
- Bus 002 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
- root@OpenWrt:/# lsusb -t
- /: Bus 02.Port 1: Dev 1, Class=root_hub, Driver=ohci-platform/1p, 12M
- /: Bus 01.Port 1: Dev 1, Class=root_hub, Driver=ehci-platform/2p, 480M
- |__ Port 1: Dev 2, If 0, Class=Vendor Specific Class, Driver=, 480M
- root@OpenWrt:/# ls /etc/config
- [0;0m6relayd[0m [0;0mdropbear[0m [0;0mluci[0m [0;0msystem[0m [0;0muhttpd[0m
- [0;0mdhcp[0m [0;0mfirewall[0m [0;0mnetwork[0m [0;0mucitrack[0m [0;0mwireless[0m
- root@OpenWrt:/# reboot
- procd: - shutdown -
- root@OpenWrt:/# [ 280.612000] br-lan: port 1(eth0.1) entered disabled state
- [ 280.620000] device eth0.1 left promiscuous mode
- [ 280.624000] device eth0 left promiscuous mode
- [ 280.632000] br-lan: port 1(eth0.1) entered disabled state
- procd: - reboot -
- [ 281.416000] Restarting system.
- [ 281.420000] triggering watchdog soft-reset...
- þ
- CFE version 1.0.37-105.22-1 for BCM96368 (32bit,SP,BE)
- Build Date: Fri Mar 19 11:53:33 CST 2010 (jojopo@broadcom_v060.comtrend.com)
- Copyright (C) 2000-2009 Broadcom Corporation.
- Parallel flash device: name AM29DL800B, id 0x22cb size 8192KB
- Total Flash size: 8192K with 135 sectors
- Chip ID: BCM6368B2, MIPS: 400MHz
- Main Thread: TP0
- Total Memory: 67108864 bytes (64MB)
- Boot Address: 0xb8000000
- Board IP address : 192.168.1.1:ffffff00
- Host IP address : 192.168.1.100
- Gateway IP address :
- Run from flash/host (f/h) : f
- Default host run file name : vmlinux
- Default host flash file name : bcm963xx_fs_kernel
- Boot delay (0-9 seconds) : 1
- Board Id (0-14) : 96368M-1341N
- Number of MAC Addresses (1-32) : 11
- Base MAC Address : 64:68:0c:
- PSI Size (1-64) KBytes : 24
- Enable Backup PSI [0|1] : 0
- System Log Size (0-256) KBytes : 0
- Main Thread Number [0|1] : 0
- *** Press any key to stop auto run (1 seconds) ***
- Auto run second count down: 110
- Booting from only image (0xb8010000) ...
- Code Address: 0x80010000, Entry Address: 0x80010000
- LZMA: Prossible old LZMA format, trying to decompress..
- Decompression OK!
- Entry at 0x80010000
- Closing network.
- Disabling Switch ports.
- Flushing Receive Buffers...
- 2 buffers found.
- Closing DMA Channels.
- Starting program at 0x80010000
- [ 0.000000] Linux version 3.10.4 (pepe@debian) (gcc version 4.6.4 (OpenWrt/Linaro GCC 4.6-2012.12 r37663) ) #6 SMP Thu Aug 8 18:37:05 CEST 2013
- [ 0.000000] Detected Broadcom 0x6368 CPU revision b2
- [ 0.000000] CPU frequency is 400 MHz
- [ 0.000000] 64MB of RAM installed
- [ 0.000000] registering 38 GPIOs
- [ 0.000000] board_bcm963xx: Boot address 0xb8000000
- [ 0.000000] board_bcm963xx: CFE version: 1.0.37-105.22-1
- [ 0.000000] bootconsole [early0] enabled
- [ 0.000000] CPU revision is: 0002a031 (Broadcom BMIPS4350)
- [ 0.000000] board_bcm963xx: board name: 96368M-1341N
- [ 0.000000] Determined physical RAM map:
- [ 0.000000] memory: 04000000 @ 00000000 (usable)
- [ 0.000000] Initrd not found or empty - disabling initrd
- [ 0.000000] Zone ranges:
- [ 0.000000] Normal [mem 0x00000000-0x03ffffff]
- [ 0.000000] Movable zone start for each node
- [ 0.000000] Early memory node ranges
- [ 0.000000] node 0: [mem 0x00000000-0x03ffffff]
- [ 0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 16 bytes.
- [ 0.000000] Primary data cache 32kB, 2-way, VIPT, cache aliases, linesize 16 bytes
- [ 0.000000] PERCPU: Embedded 7 pages/cpu @81083000 s6560 r8192 d13920 u32768
- [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 16256
- [ 0.000000] Kernel command line: root=/dev/mtdblock2 rootfstype=squashfs,jffs2 noinitrd console=ttyS0,115200
- [ 0.000000] PID hash table entries: 256 (order: -2, 1024 bytes)
- [ 0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
- [ 0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
- [ 0.000000] Memory: 61140k/65536k available (2603k kernel code, 4396k reserved, 637k data, 212k init, 0k highmem)
- [ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
- [ 0.000000] Hierarchical RCU implementation.
- [ 0.000000] NR_IRQS:128
- [ 0.000000] Calibrating delay loop... 397.82 BogoMIPS (lpj=795648)
- [ 0.032000] pid_max: default: 32768 minimum: 301
- [ 0.036000] Mount-cache hash table entries: 512
- [ 0.044000] SMP: Booting CPU1...
- [ 0.048000] CPU revision is: 0002a031 (Broadcom BMIPS4350)
- [ 0.048000] Primary instruction cache 64kB, VIPT, 4-way, linesize 16 bytes.
- [ 0.048000] Primary data cache 32kB, 2-way, VIPT, cache aliases, linesize 16 bytes
- [ 0.076000] SMP: CPU1 is running
- [ 0.076000] Brought up 2 CPUs
- [ 0.088000] NET: Registered protocol family 16
- [ 0.100000] registering PCI controller with io_map_base unset
- [ 0.116000] bio: create slab <bio-0> at 0
- [ 0.120000] PCI host bridge to bus 0000:00
- [ 0.124000] pci_bus 0000:00: root bus resource [mem 0x30000000-0x37ffffff]
- [ 0.128000] pci_bus 0000:00: root bus resource [io 0x8000000-0x800ffff]
- [ 0.132000] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff]
- [ 0.148000] pci 0000:00:01.0: BAR 0: assigned [mem 0x30000000-0x3000ffff]
- [ 0.152000] Switching to clocksource MIPS
- [ 0.164000] NET: Registered protocol family 2
- [ 0.172000] TCP established hash table entries: 512 (order: 0, 4096 bytes)
- [ 0.176000] TCP bind hash table entries: 512 (order: 0, 4096 bytes)
- [ 0.184000] TCP: Hash tables configured (established 512 bind 512)
- [ 0.192000] TCP: reno registered
- [ 0.192000] UDP hash table entries: 256 (order: 1, 8192 bytes)
- [ 0.200000] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
- [ 0.208000] NET: Registered protocol family 1
- [ 0.216000] audit: initializing netlink socket (disabled)
- [ 0.220000] type=2000 audit(0.216:1): initialized
- [ 0.248000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
- [ 0.256000] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
- [ 0.268000] msgmni has been set to 119
- [ 0.272000] io scheduler noop registered
- [ 0.276000] io scheduler cfq registered (default)
- [ 0.284000] bcm63xx_uart.0: ttyS0 at MMIO 0xb0000100 (irq = 10) is a bcm63xx_uart
- [ 0.292000] console [ttyS0] enabled, bootconsole disabled
- [ 0.292000] console [ttyS0] enabled, bootconsole disabled
- [ 0.304000] bcm63xx-rng bcm63xx-rng: registered RNG driver
- [ 0.312000] physmap platform flash device: 08000000 at 18000000
- [ 0.320000] physmap-flash.0: Found 1 x16 devices at 0x0 in 16-bit bank. Manufacturer ID 0x0000c2 Chip ID 0x0022cb
- [ 0.328000] Amd/Fujitsu Extended Query Table at 0x0040
- [ 0.336000] Amd/Fujitsu Extended Query version 1.1.
- [ 0.340000] number of CFI chips: 1
- [ 0.344000] bcm63xxpart: CFE boot tag found with version 6 and board type 96368M-1341N
- [ 0.352000] bcm63xxpart: Partition 0 is CFE offset 0 and length 10000
- [ 0.360000] bcm63xxpart: Partition 1 is kernel offset 10100 and length 12ff00
- [ 0.364000] bcm63xxpart: Partition 2 is rootfs offset 140000 and length 6b0000
- [ 0.372000] bcm63xxpart: Partition 3 is nvram offset 7f0000 and length 10000
- [ 0.380000] bcm63xxpart: Partition 4 is linux offset 10000 and length 7e0000
- [ 0.388000] bcm63xxpart: Spare partition is offset 3e0004 and length 40fffc
- [ 0.396000] 5 bcm63xxpart partitions found on MTD device physmap-flash.0
- [ 0.400000] Creating 5 MTD partitions on "physmap-flash.0":
- [ 0.408000] 0x000000000000-0x000000010000 : "CFE"
- [ 0.416000] 0x000000010100-0x000000140000 : "kernel"
- [ 0.420000] mtd: partition "kernel" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
- [ 0.436000] 0x000000140000-0x0000007f0000 : "rootfs"
- [ 0.444000] mtd: partition "rootfs" set to be root filesystem
- [ 0.448000] mtd: partition "rootfs_data" created automatically, ofs=0x3e0000, len=0x410000
- [ 0.456000] 0x0000003e0000-0x0000007f0000 : "rootfs_data"
- [ 0.464000] 0x0000007f0000-0x000000800000 : "nvram"
- [ 0.472000] 0x000000010000-0x0000007f0000 : "linux"
- [ 0.484000] bcm63xx-spi bcm63xx-spi: at 0xb0000800 (irq 9, FIFOs size 542)
- [ 0.532000] b53_common: found switch: BCM63xx, rev 0
- [ 0.536000] bcm63xx-wdt bcm63xx-wdt: started, timer margin: 30 sec
- [ 0.548000] TCP: cubic registered
- [ 0.552000] NET: Registered protocol family 17
- [ 0.556000] 8021q: 802.1Q VLAN Support v1.8
- [ 0.568000] VFS: Mounted root (squashfs filesystem) readonly on device 31:2.
- [ 0.576000] Freeing unused kernel memory: 212K (8033b000 - 80370000)
- procd: Console is alive
- procd: - watchdog -
- [ 2.724000] SCSI subsystem initialized
- [ 2.872000] usbcore: registered new interface driver usbfs
- [ 2.880000] usbcore: registered new interface driver hub
- [ 2.884000] usbcore: registered new device driver usb
- [ 2.980000] Button Hotplug driver version 0.4.1
- [ 3.604000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
- [ 3.612000] ehci-platform: EHCI generic platform driver
- [ 3.724000] ehci-platform ehci-platform: EHCI Host Controller
- [ 3.728000] ehci-platform ehci-platform: new USB bus registered, assigned bus number 1
- [ 3.736000] ehci-platform ehci-platform: irq 15, io mem 0xb0001500
- [ 3.756000] ehci-platform ehci-platform: USB 2.0 started, EHCI 1.00, overcurrent ignored
- [ 3.764000] hub 1-0:1.0: USB hub found
- [ 3.768000] hub 1-0:1.0: 2 ports detected
- [ 3.888000] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
- [ 3.892000] ohci-platform ohci-platform: Generic Platform OHCI Controller
- [ 3.900000] ohci-platform ohci-platform: new USB bus registered, assigned bus number 2
- [ 3.908000] ohci-platform ohci-platform: irq 13, io mem 0xb0001600
- [ 3.976000] hub 2-0:1.0: USB hub found
- [ 3.980000] hub 2-0:1.0: 1 port detected
- [ 4.096000] usb 1-1: new high-speed USB device number 2 using ehci-platform
- [ 4.128000] usbcore: registered new interface driver usb-storage
- [ 4.248000] input: gpio-keys-polled as /devices/platform/gpio-keys-polled.0/input/input0
- procd: - preinit -
- ifconfig: SIOCGIFFLAGS: No such device
- Press the [f] key and hit [enter] to enter failsafe mode
- mount_root: jffs2 is ready
- [ 7.736000] jffs2: notice: (305) jffs2_build_xattr_subsystem: complete building xattr subsystem, 1 of xdatum (0 unchecked, 0 orphan) and 10 of xref (0 dead, 2 orphan) found.
- ifconfig: SIOCGIFFLAGS: No such device
- procd: - early -
- procd: - watchdog -
- procd: - init -
- Please press Enter to activate this console.
- [ 10.200000] Loading modules backported from Linux version master-2013-06-27-0-gdcfa6d5
- [ 10.208000] Backport generated by backports.git backports-20130617-4-ge3220f5
- [ 10.248000] cfg80211: Calling CRDA to update world regulatory domain
- [ 10.324000] cfg80211: World regulatory domain updated:
- [ 10.328000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
- [ 10.336000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
- [ 10.344000] cfg80211: (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
- [ 10.352000] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
- [ 10.360000] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
- [ 10.368000] cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
- [ 10.496000] NET: Registered protocol family 10
- [ 11.420000] PCI: Enabling device 0000:00:01.0 (0000 -> 0002)
- [ 13.008000] cfg80211: Calling CRDA for country: AW
- [ 13.020000] cfg80211: Regulatory domain changed to country: AW
- [ 13.024000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
- [ 13.032000] cfg80211: (2402000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 2000 mBm)
- [ 13.040000] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (N/A, 2000 mBm)
- [ 13.048000] cfg80211: (5250000 KHz - 5330000 KHz @ 40000 KHz), (N/A, 2000 mBm)
- [ 13.056000] cfg80211: (5490000 KHz - 5710000 KHz @ 40000 KHz), (N/A, 2700 mBm)
- [ 13.064000] ieee80211 phy0: Atheros AR9280 Rev:2 mem=0xc0400000, irq=21
- [ 13.412000] PPP generic driver version 2.4.2
- [ 13.768000] ip_tables: (C) 2000-2006 Netfilter Core Team
- [ 13.792000] xt_time: kernel timezone is -0000
- [ 14.000000] NET: Registered protocol family 24
- [ 14.128000] nf_conntrack version 0.5.0 (958 buckets, 3832 max)
- [ 18.100000] bcm63xx_enetsw bcm63xx_enetsw.0: link UP on port2, 100Mbps, full-duplex
- [ 19.304000] bcm63xx_enetsw bcm63xx_enetsw.0: link UP on port2, 100Mbps, full-duplex
- [ 19.316000] device eth0.1 entered promiscuous mode
- [ 19.320000] device eth0 entered promiscuous mode
- [ 19.328000] br-lan: port 1(eth0.1) entered forwarding state
- [ 19.332000] br-lan: port 1(eth0.1) entered forwarding state
- [ 20.404000] IPv6: ADDRCONF(NETDEV_CHANGE): eth0.1: link becomes ready
- [ 21.336000] br-lan: port 1(eth0.1) entered forwarding state
- BusyBox v1.19.4 (2013-08-08 17:47:34 CEST) built-in shell (ash)
- Enter 'help' for a list of built-in commands.
- _______ ________ __
- | |.-----.-----.-----.| | | |.----.| |_
- | - || _ | -__| || | | || _|| _|
- |_______|| __|_____|__|__||________||__| |____|
- |__| W I R E L E S S F R E E D O M
- Z©©©©©©©©©©©©©©©©©©©©©©©©©©©©©©©©©©©©©©©©©©©©©HšP*ªRQ© BREAKER (Bleeding Edge, r37737)
- -----------------------------------------------------
- * 1/2 oz Galliano Pour all ingredients into
- * 4 oz cold Coffee an irish coffee mug filled
- * 1 1/2 oz Dark Rum with crushed ice. Stir.
- * 2 tsp. Creme de Cacao
- -----------------------------------------------------
- root@OpenWrt:/# procd: - init complete -
- ls /etc/config
- [0;0m6relayd[0m [0;0mdropbear[0m [0;0mluci[0m [0;0msystem[0m [0;0muhttpd[0m
- [0;0mdhcp[0m [0;0mfirewall[0m [0;0mnetwork[0m [0;0mucitrack[0m [0;0mwireless[0m
- root@OpenWrt:/# mtd -r erase linux
- Unlocking linux ...
- Erasing linux ...
- Rebooting ...
- procd: - shutdown -
- [ 126.896000] br-lan: port 1(eth0.1) entered disabled state
- [ 126.904000] device eth0.1 left promiscuous mode
- [ 126.912000] device eth0 left promiscuous mode
- [ 126.916000] br-lan: port 1(eth0.1) entered disabled state
- procd: - reboot -
- [ 127.628000] Restarting system.
- [ 127.632000] triggering watchdog soft-reset...
- ê
- CFE version 1.0.37-105.22-1 for BCM96368 (32bit,SP,BE)
- Build Date: Fri Mar 19 11:53:33 CST 2010 (jojopo@broadcom_v060.comtrend.com)
- Copyright (C) 2000-2009 Broadcom Corporation.
- Parallel flash device: name AM29DL800B, id 0x22cb size 8192KB
- Total Flash size: 8192K with 135 sectors
- Chip ID: BCM6368B2, MIPS: 400MHz
- Main Thread: TP0
- Total Memory: 67108864 bytes (64MB)
- Boot Address: 0xb8000000
- ** Flash image not found. **
- Board IP address : 192.168.1.1:ffffff00
- Host IP address : 192.168.1.100
- Gateway IP address :
- Run from flash/host (f/h) : f
- Default host run file name : vmlinux
- Default host flash file name : bcm963xx_fs_kernel
- Boot delay (0-9 seconds) : 1
- Board Id (0-14) : 96368M-1341N
- Number of MAC Addresses (1-32) : 11
- Base MAC Address : 64:68:0c:
- PSI Size (1-64) KBytes : 24
- Enable Backup PSI [0|1] : 0
- System Log Size (0-256) KBytes : 0
- Main Thread Number [0|1] : 0
- CFE>
- web info: Waiting for connection on socket 0.[J
- CFE>
- web info: Waiting for connection on socket 1.[J
- CFE>
- web info: Waiting for connection on socket 0.[J
- web info: Upload 4194560 bytes, Broadcom image format.[J
- CFE>
- Flashing root file system and kernel at 0xb8010000: .................................................................
- .
- *** Image flash done *** !
- Resetting board...ÿ
- CFE version 1.0.37-105.22-1 for BCM96368 (32bit,SP,BE)
- Build Date: Fri Mar 19 11:53:33 CST 2010 (jojopo@broadcom_v060.comtrend.com)
- Copyright (C) 2000-2009 Broadcom Corporation.
- Parallel flash device: name AM29DL800B, id 0x22cb size 8192KB
- Total Flash size: 8192K with 135 sectors
- Chip ID: BCM6368B2, MIPS: 400MHz
- Main Thread: TP0
- Total Memory: 67108864 bytes (64MB)
- Boot Address: 0xb8000000
- Board IP address : 192.168.1.1:ffffff00
- Host IP address : 192.168.1.100
- Gateway IP address :
- Run from flash/host (f/h) : f
- Default host run file name : vmlinux
- Default host flash file name : bcm963xx_fs_kernel
- Boot delay (0-9 seconds) : 1
- Board Id (0-14) : 96368M-1341N
- Number of MAC Addresses (1-32) : 11
- Base MAC Address : 64:68:0c:
- PSI Size (1-64) KBytes : 24
- Enable Backup PSI [0|1] : 0
- System Log Size (0-256) KBytes : 0
- Main Thread Number [0|1] : 0
- *** Press any key to stop auto run (1 seconds) ***
- Auto run second count down: 110
- Booting from only image (0xb8010000) ...
- Code Address: 0x80010000, Entry Address: 0x80010000
- LZMA: Prossible old LZMA format, trying to decompress..
- Decompression OK!
- Entry at 0x80010000
- Closing network.
- Disabling Switch ports.
- Flushing Receive Buffers...
- 0 buffers found.
- Closing DMA Channels.
- Starting program at 0x80010000
- [ 0.000000] Linux version 3.10.4 (pepe@debian) (gcc version 4.6.4 (OpenWrt/Linaro GCC 4.6-2012.12 r37663) ) #6 SMP Thu Aug 8 18:37:05 CEST 2013
- [ 0.000000] Detected Broadcom 0x6368 CPU revision b2
- [ 0.000000] CPU frequency is 400 MHz
- [ 0.000000] 64MB of RAM installed
- [ 0.000000] registering 38 GPIOs
- [ 0.000000] board_bcm963xx: Boot address 0xb8000000
- [ 0.000000] board_bcm963xx: CFE version: 1.0.37-105.22-1
- [ 0.000000] bootconsole [early0] enabled
- [ 0.000000] CPU revision is: 0002a031 (Broadcom BMIPS4350)
- [ 0.000000] board_bcm963xx: board name: 96368M-1341N
- [ 0.000000] Determined physical RAM map:
- [ 0.000000] memory: 04000000 @ 00000000 (usable)
- [ 0.000000] Initrd not found or empty - disabling initrd
- [ 0.000000] Zone ranges:
- [ 0.000000] Normal [mem 0x00000000-0x03ffffff]
- [ 0.000000] Movable zone start for each node
- [ 0.000000] Early memory node ranges
- [ 0.000000] node 0: [mem 0x00000000-0x03ffffff]
- [ 0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 16 bytes.
- [ 0.000000] Primary data cache 32kB, 2-way, VIPT, cache aliases, linesize 16 bytes
- [ 0.000000] PERCPU: Embedded 7 pages/cpu @81083000 s6560 r8192 d13920 u32768
- [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 16256
- [ 0.000000] Kernel command line: root=/dev/mtdblock2 rootfstype=squashfs,jffs2 noinitrd console=ttyS0,115200
- [ 0.000000] PID hash table entries: 256 (order: -2, 1024 bytes)
- [ 0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
- [ 0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
- [ 0.000000] Memory: 61140k/65536k available (2603k kernel code, 4396k reserved, 637k data, 212k init, 0k highmem)
- [ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
- [ 0.000000] Hierarchical RCU implementation.
- [ 0.000000] NR_IRQS:128
- [ 0.000000] Calibrating delay loop... 397.82 BogoMIPS (lpj=795648)
- [ 0.032000] pid_max: default: 32768 minimum: 301
- [ 0.036000] Mount-cache hash table entries: 512
- [ 0.044000] SMP: Booting CPU1...
- [ 0.048000] CPU revision is: 0002a031 (Broadcom BMIPS4350)
- [ 0.048000] Primary instruction cache 64kB, VIPT, 4-way, linesize 16 bytes.
- [ 0.048000] Primary data cache 32kB, 2-way, VIPT, cache aliases, linesize 16 bytes
- [ 0.076000] SMP: CPU1 is running
- [ 0.076000] Brought up 2 CPUs
- [ 0.088000] NET: Registered protocol family 16
- [ 0.100000] registering PCI controller with io_map_base unset
- [ 0.116000] bio: create slab <bio-0> at 0
- [ 0.120000] PCI host bridge to bus 0000:00
- [ 0.124000] pci_bus 0000:00: root bus resource [mem 0x30000000-0x37ffffff]
- [ 0.128000] pci_bus 0000:00: root bus resource [io 0x8000000-0x800ffff]
- [ 0.132000] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff]
- [ 0.148000] pci 0000:00:01.0: BAR 0: assigned [mem 0x30000000-0x3000ffff]
- [ 0.152000] Switching to clocksource MIPS
- [ 0.164000] NET: Registered protocol family 2
- [ 0.172000] TCP established hash table entries: 512 (order: 0, 4096 bytes)
- [ 0.176000] TCP bind hash table entries: 512 (order: 0, 4096 bytes)
- [ 0.184000] TCP: Hash tables configured (established 512 bind 512)
- [ 0.192000] TCP: reno registered
- [ 0.192000] UDP hash table entries: 256 (order: 1, 8192 bytes)
- [ 0.200000] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
- [ 0.208000] NET: Registered protocol family 1
- [ 0.216000] audit: initializing netlink socket (disabled)
- [ 0.220000] type=2000 audit(0.216:1): initialized
- [ 0.244000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
- [ 0.252000] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
- [ 0.264000] msgmni has been set to 119
- [ 0.268000] io scheduler noop registered
- [ 0.272000] io scheduler cfq registered (default)
- [ 0.280000] bcm63xx_uart.0: ttyS0 at MMIO 0xb0000100 (irq = 10) is a bcm63xx_uart
- [ 0.288000] console [ttyS0] enabled, bootconsole disabled
- [ 0.288000] console [ttyS0] enabled, bootconsole disabled
- [ 0.300000] bcm63xx-rng bcm63xx-rng: registered RNG driver
- [ 0.308000] physmap platform flash device: 08000000 at 18000000
- [ 0.312000] physmap-flash.0: Found 1 x16 devices at 0x0 in 16-bit bank. Manufacturer ID 0x0000c2 Chip ID 0x0022cb
- [ 0.324000] Amd/Fujitsu Extended Query Table at 0x0040
- [ 0.328000] Amd/Fujitsu Extended Query version 1.1.
- [ 0.336000] number of CFI chips: 1
- [ 0.340000] bcm63xxpart: CFE boot tag found with version 6 and board type 96368M-1341N
- [ 0.348000] bcm63xxpart: Partition 0 is CFE offset 0 and length 10000
- [ 0.352000] bcm63xxpart: Partition 1 is kernel offset 10100 and length 12ff00
- [ 0.360000] bcm63xxpart: Partition 2 is rootfs offset 140000 and length 6b0000
- [ 0.368000] bcm63xxpart: Partition 3 is nvram offset 7f0000 and length 10000
- [ 0.376000] bcm63xxpart: Partition 4 is linux offset 10000 and length 7e0000
- [ 0.384000] bcm63xxpart: Spare partition is offset 3e0004 and length 40fffc
- [ 0.388000] 5 bcm63xxpart partitions found on MTD device physmap-flash.0
- [ 0.396000] Creating 5 MTD partitions on "physmap-flash.0":
- [ 0.404000] 0x000000000000-0x000000010000 : "CFE"
- [ 0.408000] 0x000000010100-0x000000140000 : "kernel"
- [ 0.416000] mtd: partition "kernel" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
- [ 0.428000] 0x000000140000-0x0000007f0000 : "rootfs"
- [ 0.436000] mtd: partition "rootfs" set to be root filesystem
- [ 0.444000] mtd: partition "rootfs_data" created automatically, ofs=0x3e0000, len=0x410000
- [ 0.452000] 0x0000003e0000-0x0000007f0000 : "rootfs_data"
- [ 0.460000] 0x0000007f0000-0x000000800000 : "nvram"
- [ 0.468000] 0x000000010000-0x0000007f0000 : "linux"
- [ 0.476000] bcm63xx-spi bcm63xx-spi: at 0xb0000800 (irq 9, FIFOs size 542)
- [ 0.524000] b53_common: found switch: BCM63xx, rev 0
- [ 0.528000] bcm63xx-wdt bcm63xx-wdt: started, timer margin: 30 sec
- [ 0.540000] TCP: cubic registered
- [ 0.544000] NET: Registered protocol family 17
- [ 0.548000] 8021q: 802.1Q VLAN Support v1.8
- [ 0.560000] VFS: Mounted root (squashfs filesystem) readonly on device 31:2.
- [ 0.568000] Freeing unused kernel memory: 212K (8033b000 - 80370000)
- procd: Console is alive
- procd: - watchdog -
- [ 2.668000] SCSI subsystem initialized
- [ 2.808000] usbcore: registered new interface driver usbfs
- [ 2.812000] usbcore: registered new interface driver hub
- [ 2.820000] usbcore: registered new device driver usb
- [ 2.912000] Button Hotplug driver version 0.4.1
- [ 3.544000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
- [ 3.552000] ehci-platform: EHCI generic platform driver
- [ 3.660000] ehci-platform ehci-platform: EHCI Host Controller
- [ 3.664000] ehci-platform ehci-platform: new USB bus registered, assigned bus number 1
- [ 3.672000] ehci-platform ehci-platform: irq 15, io mem 0xb0001500
- [ 3.692000] ehci-platform ehci-platform: USB 2.0 started, EHCI 1.00, overcurrent ignored
- [ 3.700000] hub 1-0:1.0: USB hub found
- [ 3.704000] hub 1-0:1.0: 2 ports detected
- [ 3.824000] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
- [ 3.832000] ohci-platform ohci-platform: Generic Platform OHCI Controller
- [ 3.836000] ohci-platform ohci-platform: new USB bus registered, assigned bus number 2
- [ 3.844000] ohci-platform ohci-platform: irq 13, io mem 0xb0001600
- [ 3.912000] hub 2-0:1.0: USB hub found
- [ 3.916000] hub 2-0:1.0: 1 port detected
- [ 4.036000] usb 1-1: new high-speed USB device number 2 using ehci-platform
- [ 4.068000] usbcore: registered new interface driver usb-storage
- [ 4.188000] input: gpio-keys-polled as /devices/platform/gpio-keys-polled.0/input/input0
- procd: - preinit -
- ifconfig: SIOCGIFFLAGS: No such device
- Press the [f] key and hit [enter] to enter failsafe mode
- mount_root: jffs2 is not ready - marker found
- ifconfig: SIOCGIFFLAGS: No such device
- procd: - early -
- procd: - watchdog -
- procd: - init -
- Please press Enter to activate this console.
- [ 10.092000] Loading modules backported from Linux version master-2013-06-27-0-gdcfa6d5
- [ 10.100000] Backport generated by backports.git backports-20130617-4-ge3220f5
- [ 10.144000] cfg80211: Calling CRDA to update world regulatory domain
- [ 10.156000] cfg80211: World regulatory domain updated:
- [ 10.160000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
- [ 10.168000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
- [ 10.176000] cfg80211: (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
- [ 10.184000] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
- [ 10.192000] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
- [ 10.200000] cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
- [ 10.456000] NET: Registered protocol family 10
- [ 11.384000] PCI: Enabling device 0000:00:01.0 (0000 -> 0002)
- [ 12.976000] cfg80211: Calling CRDA for country: AW
- [ 12.984000] cfg80211: Regulatory domain changed to country: AW
- [ 12.988000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
- [ 13.000000] cfg80211: (2402000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 2000 mBm)
- [ 13.004000] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (N/A, 2000 mBm)
- [ 13.012000] cfg80211: (5250000 KHz - 5330000 KHz @ 40000 KHz), (N/A, 2000 mBm)
- [ 13.020000] cfg80211: (5490000 KHz - 5710000 KHz @ 40000 KHz), (N/A, 2700 mBm)
- [ 13.028000] ieee80211 phy0: Atheros AR9280 Rev:2 mem=0xc0400000, irq=21
- [ 13.376000] PPP generic driver version 2.4.2
- [ 13.732000] ip_tables: (C) 2000-2006 Netfilter Core Team
- [ 13.760000] xt_time: kernel timezone is -0000
- [ 13.960000] NET: Registered protocol family 24
- [ 14.084000] nf_conntrack version 0.5.0 (958 buckets, 3832 max)
- [ 20.328000] bcm63xx_enetsw bcm63xx_enetsw.0: link UP on port2, 100Mbps, full-duplex
- [ 21.448000] bcm63xx_enetsw bcm63xx_enetsw.0: link UP on port2, 100Mbps, full-duplex
- [ 21.464000] device eth0.1 entered promiscuous mode
- [ 21.468000] device eth0 entered promiscuous mode
- [ 21.472000] br-lan: port 1(eth0.1) entered forwarding state
- [ 21.480000] br-lan: port 1(eth0.1) entered forwarding state
- [ 22.560000] IPv6: ADDRCONF(NETDEV_CHANGE): eth0.1: link becomes ready
- [ 23.484000] br-lan: port 1(eth0.1) entered forwarding state
- [ 32.732000] jffs2_scan_eraseblock(): End of filesystem marker found at 0x0
- [ 32.740000] jffs2_build_filesystem(): unlocking the mtd device... done.
- [ 32.748000] jffs2_build_filesystem(): erasing all blocks after the end marker... done.
- [ 67.340000] jffs2: notice: (902) jffs2_build_xattr_subsystem: complete building xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0 orphan) found.
- procd: - init complete -
- BusyBox v1.19.4 (2013-08-08 17:47:34 CEST) built-in shell (ash)
- Enter 'help' for a list of built-in commands.
- _______ ________ __
- | |.-----.-----.-----.| | | |.----.| |_
- | - || _ | -__| || | | || _|| _|
- |_______|| __|_____|__|__||________||__| |____|
- |__| W I R E L E S S F R E E D O M
- -----------------------------------------------------
- BARR±¥¹*E±ÍºººJj€R©©©©©©©©©©©©©©©©©©©©©©©©©©©©©©©©©©©©©©©©©©©©©©©©©©©©©H$%HLI€K:++ë$H Pour all ingredients into
- * 4 oz cold Coffee an irish coffee mug filled
- * 1 1/2 oz Dark Rum with crushed ice. Stir.
- * 2 tsp. Creme de Cacao
- -----------------------------------------------------
- root@OpenWrt:/# [ 122.816000] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
- [ 122.868000] device wlan0 entered promiscuous mode
- [ 122.892000] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
- [ 122.924000] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
- [ 122.932000] br-lan: port 2(wlan0) entered forwarding state
- [ 122.936000] br-lan: port 2(wlan0) entered forwarding state
- [ 124.940000] br-lan: port 2(wlan0) entered forwarding state
- [ 150.416000] IPv6: ADDRCONF(NETDEV_UP): tmp.wlan0: link is not ready
- [ 152.080000] IPv6: ADDRCONF(NETDEV_UP): tmp.wlan0: link is not ready
- [ 153.752000] IPv6: ADDRCONF(NETDEV_UP): tmp.wlan0: link is not ready
- [ 159.864000] IPv6: ADDRCONF(NETDEV_UP): tmp.wlan0: link is not ready
- [ 184.812000] IPv6: ADDRCONF(NETDEV_UP): tmp.wlan0: link is not ready
- [ 202.668000] IPv6: ADDRCONF(NETDEV_UP): tmp.wlan0: link is not ready
- [ 221.816000] br-lan: port 2(wlan0) entered disabled state
- [ 221.820000] br-lan: port 1(eth0.1) entered disabled state
- [ 221.836000] device eth0.1 left promiscuous mode
- [ 221.844000] device eth0 left promiscuous mode
- [ 221.848000] br-lan: port 1(eth0.1) entered disabled state
- [ 221.896000] device wlan0 left promiscuous mode
- [ 221.900000] br-lan: port 2(wlan0) entered disabled state
- [ 221.956000] bcm63xx_enetsw bcm63xx_enetsw.0: link UP on port2, 100Mbps, full-duplex
- [ 221.972000] device eth0.1 entered promiscuous mode
- [ 221.976000] device eth0 entered promiscuous mode
- [ 221.988000] device wlan0 entered promiscuous mode
- [ 222.004000] br-lan: port 2(wlan0) entered forwarding state
- [ 222.008000] br-lan: port 2(wlan0) entered forwarding state
- [ 222.016000] br-lan: port 1(eth0.1) entered forwarding state
- [ 222.020000] br-lan: port 1(eth0.1) entered forwarding state
- [ 222.400000] device wlan0 left promiscuous mode
- [ 222.404000] br-lan: port 2(wlan0) entered disabled state
- [ 222.836000] IPv6: ADDRCONF(NETDEV_CHANGE): eth0.1: link becomes ready
- [ 224.024000] br-lan: port 1(eth0.1) entered forwarding state
- [ 224.080000] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
- [ 226.548000] wlan0: authenticate with 00:13:f7:
- [ 226.568000] wlan0: send auth to 00:13:f7: (try 1/3)
- [ 226.576000] wlan0: authenticated
- [ 226.588000] wlan0: associate with 00:13:f7: (try 1/3)
- [ 226.596000] wlan0: RX AssocResp from 00:13:f7: (capab=0x411 status=0 aid=1)
- [ 226.608000] wlan0: associated
- [ 226.612000] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
- [ 237.964000] bcm63xx_enetsw bcm63xx_enetsw.0: link DOWN on port2
- [ 247.968000] bcm63xx_enetsw bcm63xx_enetsw.0: link UP on port3, 100Mbps, full-duplex
- [ 250.976000] bcm63xx_enetsw bcm63xx_enetsw.0: link DOWN on port3
- [ 252.980000] bcm63xx_enetsw bcm63xx_enetsw.0: link UP on port3, 100Mbps, full-duplex
- [ 253.988000] bcm63xx_enetsw bcm63xx_enetsw.0: link DOWN on port3
- [ 254.992000] bcm63xx_enetsw bcm63xx_enetsw.0: link UP on port3, 100Mbps, full-duplex
- root@OpenWrt:/# reboot
- procd: - shutdown -
- root@OpenWrt:/# [ 279.020000] br-lan: port 1(eth0.1) entered disabled state
- [ 279.028000] device eth0.1 left promiscuous mode
- [ 279.036000] device eth0 left promiscuous mode
- [ 279.040000] br-lan: port 1(eth0.1) entered disabled state
- [ 279.700000] wlan0: deauthenticating from 00:13:f7: by local choice (reason=3)
- procd: - reboot -
- [ 280.196000] Restarting system.
- [ 280.200000] triggering watchdog soft-reset...
- þ
- CFE version 1.0.37-105.22-1 for BCM96368 (32bit,SP,BE)
- Build Date: Fri Mar 19 11:53:33 CST 2010 (jojopo@broadcom_v060.comtrend.com)
- Copyright (C) 2000-2009 Broadcom Corporation.
- Parallel flash device: name AM29DL800B, id 0x22cb size 8192KB
- Total Flash size: 8192K with 135 sectors
- Chip ID: BCM6368B2, MIPS: 400MHz
- Main Thread: TP0
- Total Memory: 67108864 bytes (64MB)
- Boot Address: 0xb8000000
- Board IP address : 192.168.1.1:ffffff00
- Host IP address : 192.168.1.100
- Gateway IP address :
- Run from flash/host (f/h) : f
- Default host run file name : vmlinux
- Default host flash file name : bcm963xx_fs_kernel
- Boot delay (0-9 seconds) : 1
- Board Id (0-14) : 96368M-1341N
- Number of MAC Addresses (1-32) : 11
- Base MAC Address : 64:68:0c:
- PSI Size (1-64) KBytes : 24
- Enable Backup PSI [0|1] : 0
- System Log Size (0-256) KBytes : 0
- Main Thread Number [0|1] : 0
- *** Press any key to stop auto run (1 seconds) ***
- Auto run second count down: 110
- Booting from only image (0xb8010000) ...
- Code Address: 0x80010000, Entry Address: 0x80010000
- LZMA: Prossible old LZMA format, trying to decompress..
- Decompression OK!
- Entry at 0x80010000
- Closing network.
- Disabling Switch ports.
- Flushing Receive Buffers...
- 20 buffers found.
- Closing DMA Channels.
- Starting program at 0x80010000
- [ 0.000000] Linux version 3.10.4 (pepe@debian) (gcc version 4.6.4 (OpenWrt/Linaro GCC 4.6-2012.12 r37663) ) #6 SMP Thu Aug 8 18:37:05 CEST 2013
- [ 0.000000] Detected Broadcom 0x6368 CPU revision b2
- [ 0.000000] CPU frequency is 400 MHz
- [ 0.000000] 64MB of RAM installed
- [ 0.000000] registering 38 GPIOs
- [ 0.000000] board_bcm963xx: Boot address 0xb8000000
- [ 0.000000] board_bcm963xx: CFE version: 1.0.37-105.22-1
- [ 0.000000] bootconsole [early0] enabled
- [ 0.000000] CPU revision is: 0002a031 (Broadcom BMIPS4350)
- [ 0.000000] board_bcm963xx: board name: 96368M-1341N
- [ 0.000000] Determined physical RAM map:
- [ 0.000000] memory: 04000000 @ 00000000 (usable)
- [ 0.000000] Initrd not found or empty - disabling initrd
- [ 0.000000] Zone ranges:
- [ 0.000000] Normal [mem 0x00000000-0x03ffffff]
- [ 0.000000] Movable zone start for each node
- [ 0.000000] Early memory node ranges
- [ 0.000000] node 0: [mem 0x00000000-0x03ffffff]
- [ 0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 16 bytes.
- [ 0.000000] Primary data cache 32kB, 2-way, VIPT, cache aliases, linesize 16 bytes
- [ 0.000000] PERCPU: Embedded 7 pages/cpu @81083000 s6560 r8192 d13920 u32768
- [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 16256
- [ 0.000000] Kernel command line: root=/dev/mtdblock2 rootfstype=squashfs,jffs2 noinitrd console=ttyS0,115200
- [ 0.000000] PID hash table entries: 256 (order: -2, 1024 bytes)
- [ 0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
- [ 0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
- [ 0.000000] Memory: 61140k/65536k available (2603k kernel code, 4396k reserved, 637k data, 212k init, 0k highmem)
- [ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
- [ 0.000000] Hierarchical RCU implementation.
- [ 0.000000] NR_IRQS:128
- [ 0.000000] Calibrating delay loop... 397.82 BogoMIPS (lpj=795648)
- [ 0.032000] pid_max: default: 32768 minimum: 301
- [ 0.036000] Mount-cache hash table entries: 512
- [ 0.044000] SMP: Booting CPU1...
- [ 0.048000] CPU revision is: 0002a031 (Broadcom BMIPS4350)
- [ 0.048000] Primary instruction cache 64kB, VIPT, 4-way, linesize 16 bytes.
- [ 0.048000] Primary data cache 32kB, 2-way, VIPT, cache aliases, linesize 16 bytes
- [ 0.076000] SMP: CPU1 is running
- [ 0.076000] Brought up 2 CPUs
- [ 0.088000] NET: Registered protocol family 16
- [ 0.100000] registering PCI controller with io_map_base unset
- [ 0.116000] bio: create slab <bio-0> at 0
- [ 0.120000] PCI host bridge to bus 0000:00
- [ 0.124000] pci_bus 0000:00: root bus resource [mem 0x30000000-0x37ffffff]
- [ 0.128000] pci_bus 0000:00: root bus resource [io 0x8000000-0x800ffff]
- [ 0.132000] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff]
- [ 0.148000] pci 0000:00:01.0: BAR 0: assigned [mem 0x30000000-0x3000ffff]
- [ 0.152000] Switching to clocksource MIPS
- [ 0.160000] NET: Registered protocol family 2
- [ 0.164000] TCP established hash table entries: 512 (order: 0, 4096 bytes)
- [ 0.172000] TCP bind hash table entries: 512 (order: 0, 4096 bytes)
- [ 0.180000] TCP: Hash tables configured (established 512 bind 512)
- [ 0.184000] TCP: reno registered
- [ 0.188000] UDP hash table entries: 256 (order: 1, 8192 bytes)
- [ 0.196000] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
- [ 0.204000] NET: Registered protocol family 1
- [ 0.208000] audit: initializing netlink socket (disabled)
- [ 0.216000] type=2000 audit(0.216:1): initialized
- [ 0.244000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
- [ 0.248000] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
- [ 0.264000] msgmni has been set to 119
- [ 0.268000] io scheduler noop registered
- [ 0.272000] io scheduler cfq registered (default)
- [ 0.276000] bcm63xx_uart.0: ttyS0 at MMIO 0xb0000100 (irq = 10) is a bcm63xx_uart
- [ 0.284000] console [ttyS0] enabled, bootconsole disabled
- [ 0.284000] console [ttyS0] enabled, bootconsole disabled
- [ 0.296000] bcm63xx-rng bcm63xx-rng: registered RNG driver
- [ 0.304000] physmap platform flash device: 08000000 at 18000000
- [ 0.312000] physmap-flash.0: Found 1 x16 devices at 0x0 in 16-bit bank. Manufacturer ID 0x0000c2 Chip ID 0x0022cb
- [ 0.324000] Amd/Fujitsu Extended Query Table at 0x0040
- [ 0.328000] Amd/Fujitsu Extended Query version 1.1.
- [ 0.332000] number of CFI chips: 1
- [ 0.336000] bcm63xxpart: CFE boot tag found with version 6 and board type 96368M-1341N
- [ 0.344000] bcm63xxpart: Partition 0 is CFE offset 0 and length 10000
- [ 0.352000] bcm63xxpart: Partition 1 is kernel offset 10100 and length 12ff00
- [ 0.360000] bcm63xxpart: Partition 2 is rootfs offset 140000 and length 6b0000
- [ 0.368000] bcm63xxpart: Partition 3 is nvram offset 7f0000 and length 10000
- [ 0.376000] bcm63xxpart: Partition 4 is linux offset 10000 and length 7e0000
- [ 0.380000] bcm63xxpart: Spare partition is offset 3e0004 and length 40fffc
- [ 0.388000] 5 bcm63xxpart partitions found on MTD device physmap-flash.0
- [ 0.396000] Creating 5 MTD partitions on "physmap-flash.0":
- [ 0.400000] 0x000000000000-0x000000010000 : "CFE"
- [ 0.408000] 0x000000010100-0x000000140000 : "kernel"
- [ 0.412000] mtd: partition "kernel" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
- [ 0.428000] 0x000000140000-0x0000007f0000 : "rootfs"
- [ 0.436000] mtd: partition "rootfs" set to be root filesystem
- [ 0.444000] mtd: partition "rootfs_data" created automatically, ofs=0x3e0000, len=0x410000
- [ 0.452000] 0x0000003e0000-0x0000007f0000 : "rootfs_data"
- [ 0.460000] 0x0000007f0000-0x000000800000 : "nvram"
- [ 0.468000] 0x000000010000-0x0000007f0000 : "linux"
- [ 0.476000] bcm63xx-spi bcm63xx-spi: at 0xb0000800 (irq 9, FIFOs size 542)
- [ 0.524000] b53_common: found switch: BCM63xx, rev 0
- [ 0.532000] bcm63xx-wdt bcm63xx-wdt: started, timer margin: 30 sec
- [ 0.540000] TCP: cubic registered
- [ 0.544000] NET: Registered protocol family 17
- [ 0.548000] 8021q: 802.1Q VLAN Support v1.8
- [ 0.560000] VFS: Mounted root (squashfs filesystem) readonly on device 31:2.
- [ 0.568000] Freeing unused kernel memory: 212K (8033b000 - 80370000)
- procd: Console is alive
- procd: - watchdog -
- [ 2.636000] SCSI subsystem initialized
- [ 2.784000] usbcore: registered new interface driver usbfs
- [ 2.792000] usbcore: registered new interface driver hub
- [ 2.796000] usbcore: registered new device driver usb
- [ 2.888000] Button Hotplug driver version 0.4.1
- [ 3.492000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
- [ 3.500000] ehci-platform: EHCI generic platform driver
- [ 3.608000] ehci-platform ehci-platform: EHCI Host Controller
- [ 3.612000] ehci-platform ehci-platform: new USB bus registered, assigned bus number 1
- [ 3.620000] ehci-platform ehci-platform: irq 15, io mem 0xb0001500
- [ 3.640000] ehci-platform ehci-platform: USB 2.0 started, EHCI 1.00, overcurrent ignored
- [ 3.648000] hub 1-0:1.0: USB hub found
- [ 3.652000] hub 1-0:1.0: 2 ports detected
- [ 3.764000] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
- [ 3.772000] ohci-platform ohci-platform: Generic Platform OHCI Controller
- [ 3.780000] ohci-platform ohci-platform: new USB bus registered, assigned bus number 2
- [ 3.788000] ohci-platform ohci-platform: irq 13, io mem 0xb0001600
- [ 3.852000] hub 2-0:1.0: USB hub found
- [ 3.856000] hub 2-0:1.0: 1 port detected
- [ 4.008000] usbcore: registered new interface driver usb-storage
- [ 4.076000] usb 1-1: new high-speed USB device number 2 using ehci-platform
- [ 4.132000] input: gpio-keys-polled as /devices/platform/gpio-keys-polled.0/input/input0
- procd: - preinit -
- ifconfig: SIOCGIFFLAGS: No such device
- Press the [f] key and hit [enter] to enter failsafe mode
- mount_root: jffs2 is ready
- [ 7.636000] jffs2: notice: (305) jffs2_build_xattr_subsystem: complete building xattr subsystem, 1 of xdatum (0 unchecked, 0 orphan) and 10 of xref (0 dead, 2 orphan) found.
- ifconfig: SIOCGIFFLAGS: No such device
- procd: - early -
- procd: - watchdog -
- procd: - init -
- Please press Enter to activate this console.
- [ 10.104000] Loading modules backported from Linux version master-2013-06-27-0-gdcfa6d5
- [ 10.112000] Backport generated by backports.git backports-20130617-4-ge3220f5
- [ 10.152000] cfg80211: Calling CRDA to update world regulatory domain
- [ 10.164000] cfg80211: World regulatory domain updated:
- [ 10.168000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
- [ 10.176000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
- [ 10.184000] cfg80211: (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
- [ 10.192000] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
- [ 10.200000] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
- [ 10.208000] cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
- [ 10.476000] NET: Registered protocol family 10
- [ 11.388000] PCI: Enabling device 0000:00:01.0 (0000 -> 0002)
- [ 12.980000] cfg80211: Calling CRDA for country: AW
- [ 12.988000] cfg80211: Regulatory domain changed to country: AW
- [ 12.992000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
- [ 13.000000] cfg80211: (2402000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 2000 mBm)
- [ 13.008000] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (N/A, 2000 mBm)
- [ 13.016000] cfg80211: (5250000 KHz - 5330000 KHz @ 40000 KHz), (N/A, 2000 mBm)
- [ 13.024000] cfg80211: (5490000 KHz - 5710000 KHz @ 40000 KHz), (N/A, 2700 mBm)
- [ 13.032000] ieee80211 phy0: Atheros AR9280 Rev:2 mem=0xc0400000, irq=21
- [ 13.372000] PPP generic driver version 2.4.2
- [ 13.712000] ip_tables: (C) 2000-2006 Netfilter Core Team
- [ 13.736000] xt_time: kernel timezone is -0000
- [ 13.932000] NET: Registered protocol family 24
- [ 14.052000] nf_conntrack version 0.5.0 (958 buckets, 3832 max)
- [ 17.972000] bcm63xx_enetsw bcm63xx_enetsw.0: link UP on port3, 100Mbps, full-duplex
- [ 19.188000] bcm63xx_enetsw bcm63xx_enetsw.0: link UP on port3, 100Mbps, full-duplex
- [ 19.200000] device eth0.1 entered promiscuous mode
- [ 19.208000] device eth0 entered promiscuous mode
- [ 19.212000] br-lan: port 1(eth0.1) entered forwarding state
- [ 19.220000] br-lan: port 1(eth0.1) entered forwarding state
- [ 20.184000] IPv6: ADDRCONF(NETDEV_CHANGE): eth0.1: link becomes ready
- [ 21.224000] br-lan: port 1(eth0.1) entered forwarding state
- [ 23.912000] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
- [ 26.120000] wlan0: authenticate with 00:13:f7:
- [ 26.152000] wlan0: send auth to 00:13:f7: (try 1/3)
- [ 26.160000] wlan0: authenticated
- [ 26.168000] wlan0: associate with 00:13:f7: (try 1/3)
- [ 26.176000] wlan0: RX AssocResp from 00:13:f7: (capab=0x411 status=0 aid=1)
- [ 26.188000] wlan0: associated
- [ 26.192000] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
- BusyBox v1.19.4 (2013-08-08 17:47:34 CEST) built-in shell (ash)
- Enter 'help' for a list of built-in commands.
- _______ ________ __
- | |.-----.-----.-----.| | | |.----.| |_
- | - || _ | -__| || | | || _|| _|
- |_______|| __|_____|__|__||________||__| |____|
- |__| W I R E L E S S F R E E D O M
- -----------------------------------------------------
- BARRIER Bc¥¹*Eë[ ®ŠÓÓŠS¥C!HKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKC * 1/2 oz Galliano Pour all ingredients into
- * 4 oz cold Coffee an irish coffee mug filled
- * 1 1/2 oz Dark Rum with crushed ice. Stir.
- * 2 tsp. Creme de Cacao
- -----------------------------------------------------
- root@OpenWrt:/# procd: - init complete -
- ls /etc/config
- [0;0m6relayd[0m [0;0mdropbear[0m [0;0mluci[0m [0;0msystem[0m [0;0muhttpd[0m
- [0;0mdhcp[0m [0;0mfirewall[0m [0;0mnetwork[0m [0;0mucitrack[0m [0;0mwireless[0m
- root@OpenWrt:/# exit
- Please press Enter to activate this console.
- BusyBox v1.19.4 (2013-08-08 17:47:34 CEST) built-in shell (ash)
- Enter 'help' for a list of built-in commands.
- _______ ________ __
- | |.-----.-----.-----.| | | |.----.| |_
- | - || _ | -__| || | | || _|| _|
- |_______|| __|_____|__|__||________||__| |____|
- |__| W I R E L E S S F R E E D O M
- -----------------------------------------------------
- BARRIER BREAKER (Bleeding Edge, r37737)
- -----------------------------------------------------
- * 1/2 oz Galliano Pour all ingredients into
- * 4 oz cold Coffee an irish coffee mug filled
- * 1 1/2 oz Dark Rum with crushed ice. Stir.
- * 2 tsp. Creme de Cacao
- -----------------------------------------------------
- root@OpenWrt:/#
Advertisement
Add Comment
Please, Sign In to add comment
Advertisement