API tools faq
paste
Advertisement
Guest User

Untitled

a guest
Nov 21st, 2016
612
0
Never
Add comment
Not a member of Pastebin yet? Sign Up, it unlocks many cool features!
text 20.21 KB | None | 0 0
raw download clone embed print report
  1. U-Boot 2012.07 [Standard IPQ806X.LN,r40858] (Dec 08 2015 - 15:14:35)
  2.  
  3. smem ram ptable found: ver: 0 len: 5
  4. DRAM: 491 MiB
  5. NAND: ipq_nand: unknown NAND device manufacturer: 0 device: 0
  6. ipq_nand: failed to identify device
  7. SF: we have a match, call probe
  8. SF: Detected W25Q128 with page size 64 KiB, total 16 MiB
  9. ipq_spi: page_size: 0x100, sector_size: 0x10000, size: 0x1000000
  10. 16 MiB
  11. MMC:
  12. *** Warning - bad CRC, using default environment
  13.  
  14. PCI0 Link Intialized
  15. PCI1 Link Intialized
  16. In: serial
  17. Out: serial
  18. Err: serial
  19. Net: No ART partition found
  20. MAC1 addr:0:3:7f:ba:db:1
  21. S17c athrs17_init_switch done.
  22. WJL: athrs17_reg_init() reg-0x30=0x80000700.1.
  23. WJL: athrs17_reg_init() reg-0x30=0x80000401.2.
  24. WJL: athrs17_reg_init: PAD config after SOFT_RESET.
  25. WJL: athrs17_reg_init: 0x0000007c=0x00001080.1.
  26. WJL: athrs17_reg_init: 0x00000094=0x00001080.2.
  27. athrs17_reg_init: complete
  28. S17c init done (WJL-07-10-1829, uboot task - internal loopback)
  29. MAC2 addr:0:3:7f:ba:db:2
  30. eth0
  31. Warning: eth0 MAC addresses don't match:
  32. Address in SROM is 00:03:7f:ba:db:01
  33. Address in environment is 00:aa:bb:cc:dd:ee
  34. , eth1
  35. Hit any key to stop autoboot: 1  0
  36. MMC Device 0 not found
  37. MMC Device 0 not found
  38.  
  39. Loading from nand1, offset 0x320200
  40. Image Name: ARM LEDE Linux-4.4.32
  41. Image Type: ARM Linux Kernel Image (uncompressed)
  42. Data Size: 2005364 Bytes = 1.9 MiB
  43. Load Address: 42208000
  44. Entry Point: 42208000
  45. Automatic boot of image at addr 0x44000000 ...
  46. Image Name: ARM LEDE Linux-4.4.32
  47. Image Type: ARM Linux Kernel Image (uncompressed)
  48. Data Size: 2005364 Bytes = 1.9 MiB
  49. Load Address: 42208000
  50. Entry Point: 42208000
  51. Verifying Checksum ... OK
  52. Loading Kernel Image ... OK
  53. OK
  54.  
  55. device nand1 <nand1>, # parts = 1
  56. #: name size offset mask_flags
  57. 0: ART 0x00040000 0x00fc0000 0
  58.  
  59. active partition: nand1,0 - (ART) 0x00040000 @ 0x00fc0000
  60.  
  61. defaults:
  62. mtdids : none
  63. mtdparts: none
  64. Setting up atags for msm partition: ART
  65. Using machid 0x1260 from environment
  66.  
  67. Starting kernel ...
  68.  
  69. [ 0.000000] Booting Linux on physical CPU 0x0
  70. [ 0.000000] Linux version 4.4.32 (phate@heimdall) (gcc version 5.4.0 (LEDE GCC 5.4.0 r2065) ) #0 SMP Sun Nov 20 22:23:11 2016
  71. [ 0.000000] CPU: ARMv7 Processor [512f04d0] revision 0 (ARMv7), cr=10c5787d
  72. [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, PIPT instruction cache
  73. [ 0.000000] Machine model: TP-Link Archer VR2600v
  74. [ 0.000000] Memory policy: Data cache writealloc
  75. [ 0.000000] PERCPU: Embedded 11 pages/cpu @ddc10000 s13824 r8192 d23040 u45056
  76. [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 121920
  77. [ 0.000000] Kernel command line:
  78. [ 0.000000] Bootloader command line (ignored): console=ttyHSL1,115200n8 root=mtd:rootfs rootfstype=squashfs
  79. [ 0.000000] PID hash table entries: 2048 (order: 1, 8192 bytes)
  80. [ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
  81. [ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
  82. [ 0.000000] Memory: 480732K/491520K available (4122K kernel code, 240K rwdata, 1516K rodata, 216K init, 222K bss, 10788K reserved, 0K cma-reserved, 0K highmem)
  83. [ 0.000000] Virtual kernel memory layout:
  84. [ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB)
  85. [ 0.000000] fixmap : 0xffc00000 - 0xfff00000 (3072 kB)
  86. [ 0.000000] vmalloc : 0xde800000 - 0xff800000 ( 528 MB)
  87. [ 0.000000] lowmem : 0xc0000000 - 0xde000000 ( 480 MB)
  88. [ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB)
  89. [ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB)
  90. [ 0.000000] .text : 0xc0208000 - 0xc0789c30 (5640 kB)
  91. [ 0.000000] .init : 0xc078a000 - 0xc07c0000 ( 216 kB)
  92. [ 0.000000] .data : 0xc07c0000 - 0xc07fc230 ( 241 kB)
  93. [ 0.000000] .bss : 0xc07ff000 - 0xc0836bb4 ( 223 kB)
  94. [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
  95. [ 0.000000] Hierarchical RCU implementation.
  96. [ 0.000000] RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=2.
  97. [ 0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2
  98. [ 0.000000] NR_IRQS:16 nr_irqs:16 16
  99. [ 0.000000] clocksource: dg_timer: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 305801671480 ns
  100. [ 0.000008] sched_clock: 32 bits at 6MHz, resolution 160ns, wraps every 343597383600ns
  101. [ 0.000020] Switching to timer-based delay loop, resolution 160ns
  102. [ 0.000201] Calibrating delay loop (skipped), value calculated using timer frequency.. 12.50 BogoMIPS (lpj=62500)
  103. [ 0.000223] pid_max: default: 32768 minimum: 301
  104. [ 0.000322] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
  105. [ 0.000338] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
  106. [ 0.000937] CPU: Testing write buffer coherency: ok
  107. [ 0.001281] Setting up static identity map for 0x42208280 - 0x422082d8
  108. [ 0.004333] Brought up 2 CPUs
  109. [ 0.004348] SMP: Total of 2 processors activated (25.00 BogoMIPS).
  110. [ 0.004357] CPU: All CPU(s) started in SVC mode.
  111. [ 0.012525] VFP support v0.3: implementor 51 architecture 64 part 4d variant 2 rev 0
  112. [ 0.012759] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
  113. [ 0.012899] pinctrl core: initialized pinctrl subsystem
  114. [ 0.014257] NET: Registered protocol family 16
  115. [ 0.014517] DMA: preallocated 256 KiB pool for atomic coherent allocations
  116. [ 0.041424] cpuidle: using governor ladder
  117. [ 0.072437] cpuidle: using governor menu
  118. [ 0.085445] qcom_rpm 108000.rpm: RPM firmware 3.0.16777342
  119. [ 0.126672] pps_core: LinuxPPS API ver. 1 registered
  120. [ 0.126685] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
  121. [ 0.126724] PTP clock support registered
  122. [ 0.127885] clocksource: Switched to clocksource dg_timer
  123. [ 0.129115] NET: Registered protocol family 2
  124. [ 0.129611] TCP established hash table entries: 4096 (order: 2, 16384 bytes)
  125. [ 0.129651] TCP bind hash table entries: 4096 (order: 3, 32768 bytes)
  126. [ 0.129704] TCP: Hash tables configured (established 4096 bind 4096)
  127. [ 0.129750] UDP hash table entries: 256 (order: 1, 8192 bytes)
  128. [ 0.129774] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
  129. [ 0.129962] NET: Registered protocol family 1
  130. [ 0.131300] futex hash table entries: 512 (order: 3, 32768 bytes)
  131. [ 0.131408] No memory allocated for crashlog
  132. [ 0.138200] squashfs: version 4.0 (2009/01/31) Phillip Lougher
  133. [ 0.138223] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
  134. [ 0.141110] io scheduler noop registered
  135. [ 0.141132] io scheduler deadline registered (default)
  136. [ 0.142355] 1b500000.pci supply vdda not found, using dummy regulator
  137. [ 0.142435] 1b500000.pci supply vdda_phy not found, using dummy regulator
  138. [ 0.142517] 1b500000.pci supply vdda_refclk not found, using dummy regulator
  139. [ 0.142909] PCI host bridge /soc/pci@1b500000 ranges:
  140. [ 0.142947] IO 0x0fe00000..0x0fefffff -> 0x0fe00000
  141. [ 0.142968] MEM 0x08000000..0x0fdfffff -> 0x08000000
  142. [ 0.175749] qcom-pcie 1b500000.pci: PCI host bridge to bus 0000:00
  143. [ 0.175770] pci_bus 0000:00: root bus resource [bus 00-ff]
  144. [ 0.175787] pci_bus 0000:00: root bus resource [io 0x0000-0xfffff] (bus address [0xfe00000-0xfefffff])
  145. [ 0.175801] pci_bus 0000:00: root bus resource [mem 0x08000000-0x0fdfffff]
  146. [ 0.176301] PCI: bus0: Fast back to back transfers disabled
  147. [ 0.178153] PCI: bus1: Fast back to back transfers disabled
  148. [ 0.178416] pci 0000:00:00.0: BAR 8: assigned [mem 0x08000000-0x081fffff]
  149. [ 0.178439] pci 0000:01:00.0: BAR 0: assigned [mem 0x08000000-0x081fffff 64bit]
  150. [ 0.178542] pci 0000:00:00.0: PCI bridge to [bus 01]
  151. [ 0.178561] pci 0000:00:00.0: bridge window [mem 0x08000000-0x081fffff]
  152. [ 0.179252] 1b700000.pci supply vdda not found, using dummy regulator
  153. [ 0.179327] 1b700000.pci supply vdda_phy not found, using dummy regulator
  154. [ 0.179405] 1b700000.pci supply vdda_refclk not found, using dummy regulator
  155. [ 0.179772] PCI host bridge /soc/pci@1b700000 ranges:
  156. [ 0.179804] IO 0x31e00000..0x31efffff -> 0x31e00000
  157. [ 0.179823] MEM 0x2e000000..0x31dfffff -> 0x2e000000
  158. [ 0.208875] qcom-pcie 1b700000.pci: PCI host bridge to bus 0001:00
  159. [ 0.208893] pci_bus 0001:00: root bus resource [bus 00-ff]
  160. [ 0.208907] pci_bus 0001:00: root bus resource [mem 0x2e000000-0x31dfffff]
  161. [ 0.209353] PCI: bus0: Fast back to back transfers disabled
  162. [ 0.211060] PCI: bus1: Fast back to back transfers disabled
  163. [ 0.211433] pci 0001:00:00.0: BAR 8: assigned [mem 0x2e000000-0x2e1fffff]
  164. [ 0.211454] pci 0001:01:00.0: BAR 0: assigned [mem 0x2e000000-0x2e1fffff 64bit]
  165. [ 0.211554] pci 0001:00:00.0: PCI bridge to [bus 01]
  166. [ 0.211572] pci 0001:00:00.0: bridge window [mem 0x2e000000-0x2e1fffff]
  167. [ 0.214051] gsbi 16300000.gsbi: GSBI port protocol: 6 crci: 0
  168. [ 0.215100] gsbi 1a200000.gsbi: GSBI port protocol: 3 crci: 0
  169. [ 0.216110] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
  170. [ 0.216849] msm_serial 16340000.serial: msm_serial: detected port #0
  171. [ 0.216952] msm_serial 16340000.serial: uartclk = 1843200
  172. [ 0.217008] 16340000.serial: ttyMSM0 at MMIO 0x16340000 (irq = 166, base_baud = 115200) is a MSM
  173. [ 0.217045] msm_serial: console setup on port #0
  174. [ 0.858249] console [ttyMSM0] enabled
  175. [ 0.862960] msm_serial: driver initialized
  176. [ 0.873194] loop: module loaded
  177. [ 0.874361] spi_qup 1a280000.spi: IN:block:16, fifo:64, OUT:block:16, fifo:64
  178. [ 0.876309] m25p80 spi32766.0: w25q128fw (16384 Kbytes)
  179. [ 0.882626] 15 ofpart partitions found on MTD device spi32766.0
  180. [ 0.887469] Creating 15 MTD partitions on "spi32766.0":
  181. [ 0.893444] 0x000000000000-0x000000020000 : "SBL1"
  182. [ 0.899669] 0x000000020000-0x000000040000 : "MIBIB"
  183. [ 0.904388] 0x000000040000-0x000000080000 : "SBL2"
  184. [ 0.909225] 0x000000080000-0x000000100000 : "SBL3"
  185. [ 0.913977] 0x000000100000-0x000000110000 : "DDRCONFIG"
  186. [ 0.918733] 0x000000110000-0x000000120000 : "SSD"
  187. [ 0.923931] 0x000000120000-0x0000001a0000 : "TZ"
  188. [ 0.928888] 0x0000001a0000-0x000000220000 : "RPM"
  189. [ 0.933488] 0x000000220000-0x0000002a0000 : "APPSBL"
  190. [ 0.938118] 0x0000002a0000-0x0000002e0000 : "APPSBLENV"
  191. [ 0.943079] 0x0000002e0000-0x000000320000 : "OLDART"
  192. [ 0.948081] 0x000000320000-0x000000520000 : "kernel"
  193. [ 0.953234] 0x000000520000-0x000000f80000 : "rootfs"
  194. [ 0.958231] mtd: device 12 (rootfs) set to be root filesystem
  195. [ 0.962399] 1 squashfs-split partitions found on MTD device rootfs
  196. [ 0.967855] 0x000000920000-0x000000f80000 : "rootfs_data"
  197. [ 0.974956] 0x000000faf100-0x000000faf300 : "default-mac"
  198. [ 0.980391] 0x000000fc0000-0x000001000000 : "ART"
  199. [ 0.986162] libphy: Fixed MDIO Bus: probed
  200. [ 0.989916] libphy: GPIO Bitbanged MDIO: probed
  201. [ 1.015143] switch0: Atheros AR8337 rev. 2 switch registered on gpio-0
  202. [ 1.241415] stmmac - user ID: 0x10, Synopsys ID: 0x37
  203. [ 1.241438] Ring mode enabled
  204. [ 1.245436] DMA HW capability register supported
  205. [ 1.248488] Enhanced/Alternate descriptors
  206. [ 1.253162] Enabled extended descriptors
  207. [ 1.257158] RX Checksum Offload Engine supported (type 2)
  208. [ 1.261381] TX Checksum insertion supported
  209. [ 1.266704] Wake-Up On Lan supported
  210. [ 1.271192] Enable RX Mitigation via HW Watchdog Timer
  211. [ 1.276062] stmmac - user ID: 0x10, Synopsys ID: 0x37
  212. [ 1.279827] Ring mode enabled
  213. [ 1.284932] DMA HW capability register supported
  214. [ 1.287885] Enhanced/Alternate descriptors
  215. [ 1.292660] Enabled extended descriptors
  216. [ 1.296652] RX Checksum Offload Engine supported (type 2)
  217. [ 1.300899] TX Checksum insertion supported
  218. [ 1.306201] Wake-Up On Lan supported
  219. [ 1.310709] Enable RX Mitigation via HW Watchdog Timer
  220. [ 1.314831] i2c /dev entries driver
  221. [ 1.320319] Speed bin: 0
  222. [ 1.322693] PVS bin: 1
  223. [ 1.325899] cpuidle: enable-method property 'qcom,kpss-acc-v1' found operations
  224. [ 1.327682] cpuidle: enable-method property 'qcom,kpss-acc-v1' found operations
  225. [ 1.335060] sdhci: Secure Digital Host Controller Interface driver
  226. [ 1.342200] sdhci: Copyright(c) Pierre Ossman
  227. [ 1.348464] sdhci-pltfm: SDHCI platform and OF driver helper
  228. [ 1.354656] L2 @ QSB rate. Forcing new rate.
  229. [ 1.358750] L2 @ 384000 KHz
  230. [ 1.362915] CPU0 @ 800000 KHz
  231. [ 1.365316] CPU1 @ QSB rate. Forcing new rate.
  232. [ 1.368579] CPU1 @ 384000 KHz
  233. [ 1.374382] NET: Registered protocol family 10
  234. [ 1.376986] NET: Registered protocol family 17
  235. [ 1.380341] bridge: automatic filtering via arp/ip/ip6tables has been deprecated. Update your scripts to load br_netfilter if you need this.
  236. [ 1.384880] 8021q: 802.1Q VLAN Support v1.8
  237. [ 1.397505] Registering SWP/SWPB emulation handler
  238. [ 1.403338] cpu: dev_pm_opp_of_cpumask_add_table: couldn't find opp table for cpu:0, -19
  239. [ 1.406752] cpu: dev_pm_opp_of_cpumask_add_table: couldn't find opp table for cpu:1, -19
  240. [ 1.414786] hctosys: unable to open rtc device (rtc0)
  241. [ 1.435076] VFS: Mounted root (squashfs filesystem) readonly on device 31:12.
  242. [ 1.435261] Freeing unused kernel memory: 216K (c078a000 - c07c0000)
  243. [ 1.745947] random: nonblocking pool is initialized
  244. [ 2.667631] init: Console is alive
  245. [ 2.667748] init: - watchdog -
  246. [ 4.664735] usbcore: registered new interface driver usbfs
  247. [ 4.664804] usbcore: registered new interface driver hub
  248. [ 4.669259] usbcore: registered new device driver usb
  249. [ 4.678124] SCSI subsystem initialized
  250. [ 4.684987] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
  251. [ 4.685387] ehci-platform: EHCI generic platform driver
  252. [ 4.692843] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
  253. [ 4.695922] ohci-platform: OHCI generic platform driver
  254. [ 5.205211] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller
  255. [ 5.205252] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 1
  256. [ 5.209837] xhci-hcd xhci-hcd.0.auto: hcc params 0x0228f065 hci version 0x100 quirks 0x00010010
  257. [ 5.217174] xhci-hcd xhci-hcd.0.auto: irq 168, io mem 0x11000000
  258. [ 5.227231] hub 1-0:1.0: USB hub found
  259. [ 5.232226] hub 1-0:1.0: 1 port detected
  260. [ 5.236141] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller
  261. [ 5.239877] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 2
  262. [ 5.245293] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM.
  263. [ 5.253026] hub 2-0:1.0: USB hub found
  264. [ 5.260970] hub 2-0:1.0: 1 port detected
  265. [ 5.264672] xhci-hcd xhci-hcd.1.auto: xHCI Host Controller
  266. [ 5.268613] xhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus number 3
  267. [ 5.273976] xhci-hcd xhci-hcd.1.auto: hcc params 0x0228f065 hci version 0x100 quirks 0x00010010
  268. [ 5.281465] xhci-hcd xhci-hcd.1.auto: irq 169, io mem 0x10000000
  269. [ 5.290580] hub 3-0:1.0: USB hub found
  270. [ 5.296324] hub 3-0:1.0: 1 port detected
  271. [ 5.300122] xhci-hcd xhci-hcd.1.auto: xHCI Host Controller
  272. [ 5.303945] xhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus number 4
  273. [ 5.309379] usb usb4: We don't know the algorithms for LPM for this host, disabling LPM.
  274. [ 5.317212] hub 4-0:1.0: USB hub found
  275. [ 5.325199] hub 4-0:1.0: 1 port detected
  276. [ 5.333848] init: - preinit -
  277. [ 6.706104] eth1: device MAC address 00:03:7f:ba:db:02
  278. Press the [f] key and hit [enter] to enter failsafe mode
  279. Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level
  280. [ 8.703609] ipq806x-gmac-dwmac 37400000.ethernet eth1: Link is Up - 1Gbps/Full - flow control off
  281. [ 10.030135] jffs2: notice: (148) jffs2_build_xattr_subsystem: complete building xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0 orphan) found.
  282. [ 10.053458] mount_root: switching to jffs2 overlay
  283. [ 10.072686] urandom-seed: Seeding with /etc/urandom.seed
  284. [ 10.163361] procd: - early -
  285. [ 10.163425] procd: - watchdog -
  286. [ 10.780593] procd: - ubus -
  287. [ 10.856166] procd: - init -
  288. Please press Enter to activate this console.
  289. [ 11.093804] NET: Registered protocol family 8
  290. [ 11.093828] NET: Registered protocol family 20
  291. [ 11.098457] tun: Universal TUN/TAP device driver, 1.6
  292. [ 11.101483] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
  293. [ 11.110063] ip6_tables: (C) 2000-2006 Netfilter Core Team
  294. [ 11.119314] Loading modules backported from Linux version wt-2016-10-03-1-g6fcb1a6
  295. [ 11.119346] Backport generated by backports.git backports-20160324-9-g0e38f5c
  296. [ 11.146328] ath10k_pci 0000:01:00.0: enabling device (0140 -> 0142)
  297. [ 11.146863] ath10k_pci 0000:01:00.0: pci irq msi oper_irq_mode 2 irq_mode 0 reset_mode 0
  298. [ 11.281964] ath10k_pci 0000:01:00.0: Direct firmware load for ath10k/pre-cal-pci-0000:01:00.0.bin failed with error -2
  299. [ 11.282003] ath10k_pci 0000:01:00.0: Falling back to user helper
  300. [ 11.330630] firmware ath10k!pre-cal-pci-0000:01:00.0.bin: firmware_loading_store: map pages failed
  301. [ 11.886226] ath10k_pci 0000:01:00.0: qca99x0 hw2.0 target 0x01000000 chip_id 0x003b01ff sub 168c:0002
  302. [ 11.886279] ath10k_pci 0000:01:00.0: kconfig debug 0 debugfs 1 tracing 0 dfs 1 testmode 1
  303. [ 11.897727] ath10k_pci 0000:01:00.0: firmware ver 10.4.1.00030-1 api 5 features no-p2p crc32 d2901e01
  304. [ 11.903426] ath10k_pci 0000:01:00.0: failed to fetch board data for bus=pci,vendor=168c,device=0040,subsystem-vendor=168c,subsystem-device=0002 from ath10k/QCA99X0/hw2.0/board-2.bin
  305. [ 11.913619] ath10k_pci 0000:01:00.0: board_file api 1 bmi_id N/A crc32 7e56fd07
  306. [ 13.098554] ath10k_pci 0000:01:00.0: htt-ver 2.2 wmi-op 6 htt-op 4 cal file max-sta 512 raw 0 hwcrypto 1
  307. [ 13.178467] ath10k_pci 0001:01:00.0: enabling device (0140 -> 0142)
  308. [ 13.179222] ath10k_pci 0001:01:00.0: pci irq msi oper_irq_mode 2 irq_mode 0 reset_mode 0
  309. [ 13.309712] ath10k_pci 0001:01:00.0: Direct firmware load for ath10k/pre-cal-pci-0001:01:00.0.bin failed with error -2
  310. [ 13.309750] ath10k_pci 0001:01:00.0: Falling back to user helper
  311. [ 13.424725] firmware ath10k!pre-cal-pci-0001:01:00.0.bin: firmware_loading_store: map pages failed
  312. [ 13.430147] ath10k_pci 0001:01:00.0: qca99x0 hw2.0 target 0x01000000 chip_id 0x003b01ff sub 168c:0002
  313. [ 13.432588] ath10k_pci 0001:01:00.0: kconfig debug 0 debugfs 1 tracing 0 dfs 1 testmode 1
  314. [ 13.444368] ath10k_pci 0001:01:00.0: firmware ver 10.4.1.00030-1 api 5 features no-p2p crc32 d2901e01
  315. [ 13.450598] ath10k_pci 0001:01:00.0: failed to fetch board data for bus=pci,vendor=168c,device=0040,subsystem-vendor=168c,subsystem-device=0002 from ath10k/QCA99X0/hw2.0/board-2.bin
  316. [ 13.459408] ath10k_pci 0001:01:00.0: board_file api 1 bmi_id N/A crc32 7e56fd07
  317. [ 14.644997] ath10k_pci 0001:01:00.0: htt-ver 2.2 wmi-op 6 htt-op 4 cal file max-sta 512 raw 0 hwcrypto 1
  318. [ 14.715641] ip_tables: (C) 2000-2006 Netfilter Core Team
  319. [ 14.724000] nf_conntrack version 0.5.0 (7514 buckets, 30056 max)
  320. [ 14.854219] xt_time: kernel timezone is -0000
  321. [ 14.862532] PPP generic driver version 2.4.2
  322. [ 14.864367] NET: Registered protocol family 24
  323. [ 17.133722] device eth1 entered promiscuous mode
  324. [ 17.135965] IPv6: ADDRCONF(NETDEV_UP): br-lan: link is not ready
  325. [ 17.151960] eth0: device MAC address 00:aa:bb:cc:dd:ee
  326. [ 19.110353] ipq806x-gmac-dwmac 37400000.ethernet eth1: Link is Up - 1Gbps/Full - flow control off
  327. [ 19.110469] br-lan: port 1(eth1) entered forwarding state
  328. [ 19.118430] br-lan: port 1(eth1) entered forwarding state
  329. [ 19.123878] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready
  330. [ 19.148377] ipq806x-gmac-dwmac 37200000.ethernet eth0: Link is Up - 1Gbps/Full - flow control off
  331. [ 21.118292] br-lan: port 1(eth1) entered forwarding state
  332.  
  333.  
  334.  
  335. BusyBox v1.25.1 () built-in shell (ash)
  336.  
  337. _________
  338. / /\ _ ___ ___ ___
  339. / LE / \ | | | __| \| __|
  340. / DE / \ | |__| _|| |) | _|
  341. /________/ LE \ |____|___|___/|___| lede-project.org
  342. \ \ DE /
  343. \ LE \ / -----------------------------------------------------------
  344. \ DE \ / Reboot (HEAD, r2245)
  345. \________\/ -----------------------------------------------------------
  346.  
  347. === WARNING! =====================================
  348. There is no root password defined on this device!
  349. Use the "passwd" command to set up a new password
Advertisement
Add Comment
Please, Sign In to add comment
Advertisement
Public Pastes
Advertisement
We use cookies for various purposes including analytics. By continuing to use Pastebin, you agree to our use of cookies as described in the Cookies Policy.  OK, I Understand
Not a member of Pastebin yet?
Sign Up, it unlocks many cool features!