API tools faq
paste
Guest User

1043ND bootlog 3

a guest
Jan 27th, 2013
513
0
Never
Add comment
Not a member of Pastebin yet? Sign Up, it unlocks many cool features!
text 10.91 KB | None | 0 0
raw download clone embed print report
  1. =~=~=~=~=~=~=~=~=~=~=~= PuTTY log 2013.01.27 17:26:58 =~=~=~=~=~=~=~=~=~=~=~=
  2.  
  3. root@OpenWrt:~# [ 151.800000] br-lan: port 1(eth0.1) entered disabled state
  4. [ 151.820000] device eth0.1 left promiscuous mode
  5. [ 151.820000] device eth0 left promiscuous mode
  6. [ 151.820000] br-lan: port 1(eth0.1) entered disabled state
  7. [ 154.210000] Removing MTD device #3 (rootfs_data) with use count 1
  8. [ 154.220000] Restarting system.
  9.  
  10.  
  11. U-Boot 1.1.4 (Jan 28 2013 - 00:22:45)
  12.  
  13. AP83 (ar9100) U-boot 0.0.11
  14. DRAM:
  15. sri
  16. 64 MB
  17. id read 0x100000ff
  18. flash size 16MB, sector count = 256
  19. Flash: 16 MB
  20. Using default environment
  21.  
  22. In: serial
  23. Out: serial
  24. Err: serial
  25. Net: ag7100_enet_initialize...
  26. No valid address in Flash. Using fixed address
  27. : cfg1 0xf cfg2 0x7114
  28. eth0: 00:03:7f:09:0b:ad
  29. eth0 up
  30. eth0
  31. Autobooting in 3 seconds## Booting image at bf020000 ...
  32. Uncompressing Kernel Image ... OK
  33.  
  34. Starting kernel ...
  35.  
  36.  
  37.  
  38.  
  39. OpenWrt kernel loader for AR7XXX/AR9XXX
  40.  
  41. Copyright (C) 2011 Gabor Juhos <[email protected]>
  42.  
  43. Looking for OpenWrt image... found at 0xbf022000
  44.  
  45. Decompressing kernel... done!
  46.  
  47. Starting kernel at 80060000...
  48.  
  49.  
  50. [ 0.000000] Linux version 3.3.8 (xopal@debian) (gcc version 4.6.3 20120201 (prerelease) (Linaro GCC 4.6-2012.02) ) #2 Sun Jan 27 21:41:18 WIT 2013
  51. [ 0.000000] bootconsole [early0] enabled
  52. [ 0.000000] CPU revision is: 00019374 (MIPS 24Kc)
  53. [ 0.000000] SoC: Atheros AR9132 rev 2
  54. [ 0.000000] Clocks: CPU:400.000MHz, DDR:400.000MHz, AHB:200.000MHz, Ref:5.000MHz
  55. [ 0.000000] Determined physical RAM map:
  56. [ 0.000000] memory: 04000000 @ 00000000 (usable)
  57. [ 0.000000] Initrd not found or empty - disabling initrd
  58. [ 0.000000] Zone PFN ranges:
  59. [ 0.000000] Normal 0x00000000 -> 0x00004000
  60. [ 0.000000] Movable zone start PFN for each node
  61. [ 0.000000] Early memory PFN ranges
  62. [ 0.000000] 0: 0x00000000 -> 0x00004000
  63. [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 16256
  64. [ 0.000000] Kernel command line: board=TL-WR1043ND console=ttyS0,115200 rootfstype=squashfs,jffs2 noinitrd
  65. [ 0.000000] PID hash table entries: 256 (order: -2, 1024 bytes)
  66. [ 0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
  67. [ 0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
  68. [ 0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
  69. [ 0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
  70. [ 0.000000] Writing ErrCtl register=00000000
  71. [ 0.000000] Readback ErrCtl register=00000000
  72. [ 0.000000] Memory: 61636k/65536k available (2086k kernel code, 3900k reserved, 403k data, 208k init, 0k highmem)
  73. [ 0.000000] SLUB: Genslabs=9, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
  74. [ 0.000000] NR_IRQS:51
  75. [ 0.000000] Calibrating delay loop... 265.42 BogoMIPS (lpj=1327104)
  76. [ 0.080000] pid_max: default: 32768 minimum: 301
  77. [ 0.080000] Mount-cache hash table entries: 512
  78. [ 0.090000] NET: Registered protocol family 16
  79. [ 0.090000] gpiochip_add: registered GPIOs 0 to 21 on device: ath79
  80. [ 0.100000] MIPS: machine is TP-LINK TL-WR1043ND
  81. [ 0.360000] bio: create slab <bio-0> at 0
  82. [ 0.370000] Switching to clocksource MIPS
  83. [ 0.380000] NET: Registered protocol family 2
  84. [ 0.380000] IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
  85. [ 0.380000] TCP established hash table entries: 2048 (order: 2, 16384 bytes)
  86. [ 0.390000] TCP bind hash table entries: 2048 (order: 1, 8192 bytes)
  87. [ 0.390000] TCP: Hash tables configured (established 2048 bind 2048)
  88. [ 0.400000] TCP reno registered
  89. [ 0.400000] UDP hash table entries: 256 (order: 0, 4096 bytes)
  90. [ 0.410000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
  91. [ 0.420000] NET: Registered protocol family 1
  92. [ 0.440000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
  93. [ 0.440000] JFFS2 version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
  94. [ 0.450000] msgmni has been set to 120
  95. [ 0.460000] io scheduler noop registered
  96. [ 0.460000] io scheduler deadline registered (default)
  97. [ 0.470000] Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled
  98. [ 0.490000] serial8250.0: ttyS0 at MMIO 0x18020000 (irq = 11) is a 16550A
  99. [ 0.500000] console [ttyS0] enabled, bootconsole disabled
  100. [ 0.500000] console [ttyS0] enabled, bootconsole disabled
  101. [ 0.520000] m25p80 spi0.0: found mx25l12805d, expected m25p80
  102. [ 0.520000] m25p80 spi0.0: mx25l12805d (16384 Kbytes)
  103. [ 0.530000] 5 tp-link partitions found on MTD device spi0.0
  104. [ 0.530000] Creating 5 MTD partitions on "spi0.0":
  105. [ 0.540000] 0x000000000000-0x000000020000 : "u-boot"
  106. [ 0.540000] 0x000000020000-0x000000100a00 : "kernel"
  107. [ 0.550000] mtd: partition "kernel" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
  108. [ 0.560000] 0x000000100a00-0x000000ff0000 : "rootfs"
  109. [ 0.570000] mtd: partition "rootfs" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
  110. [ 0.580000] mtd: partition "rootfs" set to be root filesystem
  111. [ 0.590000] mtd: partition "rootfs_data" created automatically, ofs=260000, len=D90000
  112. [ 0.600000] 0x000000260000-0x000000ff0000 : "rootfs_data"
  113. [ 0.600000] 0x000000ff0000-0x000001000000 : "art"
  114. [ 0.610000] 0x000000020000-0x000000ff0000 : "firmware"
  115. [ 0.620000] Realtek RTL8366RB ethernet switch driver version 0.2.3
  116. [ 0.740000] rtl8366rb rtl8366rb: using GPIO pins 18 (SDA) and 19 (SCK)
  117. [ 0.740000] rtl8366rb rtl8366rb: RTL5937 ver. 3 chip found
  118. [ 0.920000] rtl8366rb: probed
  119. [ 0.930000] eth0: Atheros AG71xx at 0xb9000000, irq 4
  120. [ 1.230000] TCP cubic registered
  121. [ 1.240000] NET: Registered protocol family 17
  122. [ 1.240000] 8021q: 802.1Q VLAN Support v1.8
  123. [ 1.250000] VFS: Mounted root (squashfs filesystem) readonly on device 31:2.
  124. [ 1.260000] Freeing unused kernel memory: 208k freed
  125. [ 3.130000] eth0: link up (1000Mbps/Full duplex)
  126. - preinit -
  127. Press the [f] key and hit [enter] to enter failsafe mode
  128. - regular preinit -
  129. [ 6.590000] JFFS2 notice: (406) jffs2_build_xattr_subsystem: complete building xattr subsystem, 2 of xdatum (0 unchecked, 2 orphan) and 2 of xref (0 dead, 2 orphan) found.
  130. switching to jffs2
  131. - init -
  132. [ 6.780000] eth0: link down
  133.  
  134. Please press Enter to activate this console. [ 7.410000] Compat-drivers backport release: compat-drivers-2012-09-04-2-gddac993
  135. [ 7.420000] Backport based on wireless-testing.git master-2012-09-07
  136. [ 7.430000] compat.git: wireless-testing.git
  137. [ 7.580000] cfg80211: Calling CRDA to update world regulatory domain
  138. [ 7.580000] cfg80211: World regulatory domain updated:
  139. [ 7.590000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
  140. [ 7.600000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
  141. [ 7.600000] cfg80211: (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
  142. [ 7.610000] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
  143. [ 7.620000] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
  144. [ 7.630000] cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
  145. [ 8.090000] ieee80211 phy0: Atheros AR9100 MAC/BB Rev:7 AR2133 RF Rev:a2 mem=0xb80c0000, irq=2
  146. [ 8.110000] cfg80211: Calling CRDA for country: US
  147. [ 8.110000] cfg80211: Regulatory domain changed to country: US
  148. [ 8.120000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
  149. [ 8.120000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2700 mBm)
  150. [ 8.130000] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 1700 mBm)
  151. [ 8.140000] cfg80211: (5250000 KHz - 5330000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
  152. [ 8.150000] cfg80211: (5490000 KHz - 5600000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
  153. [ 8.160000] cfg80211: (5650000 KHz - 5710000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
  154. [ 8.160000] cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 3000 mBm)
  155. [ 8.310000] PPP generic driver version 2.4.2
  156. [ 8.560000] ip_tables: (C) 2000-2006 Netfilter Core Team
  157. [ 8.660000] NET: Registered protocol family 24
  158. [ 8.680000] nf_conntrack version 0.5.0 (966 buckets, 3864 max)
  159. [ 12.550000] eth0: link up (1000Mbps/Full duplex)
  160. [ 12.550000] device eth0.1 entered promiscuous mode
  161. [ 12.560000] device eth0 entered promiscuous mode
  162. [ 12.570000] br-lan: port 1(eth0.1) entered forwarding state
  163. [ 12.570000] br-lan: port 1(eth0.1) entered forwarding state
  164. [ 14.570000] br-lan: port 1(eth0.1) entered forwarding state
  165.  
  166.  
  167.  
  168. BusyBox v1.19.4 (2013-01-24 14:35:12 WIT) built-in shell (ash)
  169. Enter 'help' for a list of built-in commands.
  170.  
  171. _______ ________ __
  172. | |.-----.-----.-----.| | | |.----.| |_
  173. | - || _ | -__| || | | || _|| _|
  174. |_______|| __|_____|__|__||________||__| |____|
  175. |__| W I R E L E S S F R E E D O M
  176. -----------------------------------------------------
  177. ATTITUDE ADJUSTMENT (Attitude Adjustment, r35298)
  178. -----------------------------------------------------
  179. * 1/4 oz Vodka Pour all ingredients into mixing
  180. * 1/4 oz Gin tin with ice, strain into glass.
  181. * 1/4 oz Amaretto
  182. * 1/4 oz Triple sec
  183. * 1/4 oz Peach schnapps
  184. * 1/4 oz Sour mix
  185. * 1 splash Cranberry juice
  186. -----------------------------------------------------
  187. root@OpenWrt:/# df -h
  188. Filesystem Size Used Available Use% Mounted on
  189. rootfs 13.6M 464.0K 13.1M 3% /
  190. /dev/root 1.5M 1.5M 0 100% /rom
  191. tmpfs 30.2M 60.0K 30.1M 0% /tmp
  192. tmpfs 512.0K 0 512.0K 0% /dev
  193. /dev/mtdblock3 13.6M 464.0K 13.1M 3% /overlay
  194. overlayfs:/overlay 13.6M 464.0K 13.1M 3% /
  195. root@OpenWrt:/# free
  196. total used free shared buffers
  197. Mem: 61844 14212 47632 0 1260
  198. -/+ buffers: 12952 48892
  199. Swap: 0 0 0
  200. root@OpenWrt:/# cat /proc/cpuinfo
  201. system type : Atheros AR9132 rev 2
  202. machine : TP-LINK TL-WR1043ND
  203. processor : 0
  204. cpu model : MIPS 24Kc V7.4
  205. BogoMIPS : 265.42
  206. wait instruction : yes
  207. microsecond timers : yes
  208. tlb_entries : 16
  209. extra interrupt vector : yes
  210. hardware watchpoint : yes, count: 4, address/irw mask: [0x0000, 0x0ff8, 0x0ff8, 0x0ff8]
  211. ASEs implemented : mips16
  212. shadow register sets : 1
  213. kscratch registers : 0
  214. core : 0
  215. VCED exceptions : not available
  216. VCEI exceptions : not available
  217.  
  218. root@OpenWrt:/# cat /proc/mtd
  219. dev: size erasesize name
  220. mtd0: 00020000 00010000 "u-boot"
  221. mtd1: 000e0a00 00010000 "kernel"
  222. mtd2: 00eef600 00010000 "rootfs"
  223. mtd3: 00d90000 00010000 "rootfs_data"
  224. mtd4: 00010000 00010000 "art"
  225. mtd5: 00fd0000 00010000 "firmware"
  226. root@OpenWrt:/#
Advertisement
Add Comment
Please, Sign In to add comment
Public Pastes
We use cookies for various purposes including analytics. By continuing to use Pastebin, you agree to our use of cookies as described in the Cookies Policy.  OK, I Understand
Not a member of Pastebin yet?
Sign Up, it unlocks many cool features!