slic3r-ini-4-Qu-Bd-1up.txt

Repetier slic3r.ini contents for QU-BD One-Up as of 2014-08-26:
---------------------------------------------------------------
avoid_crossing_perimeters = 0
bottom_solid_layers = 3
bridge_acceleration = 0
bridge_flow_ratio = 1.03
bridge_speed = 10
brim_width = 0
complete_objects = 0
default_acceleration = 0
external_perimeter_speed = 100%
external_perimeters_first = 0
extra_perimeters = 1
extruder_clearance_height = 20
extruder_clearance_radius = 20
extrusion_width = 0
fill_angle = 45
fill_density = .4
fill_pattern = rectilinear
first_layer_acceleration = 0
first_layer_extrusion_width = 0
first_layer_height = 0.35
first_layer_speed = 20
gap_fill_speed = 20
gcode_comments = 0
infill_acceleration = 0
infill_every_layers = 1
infill_extruder = 1
infill_extrusion_width = 0
infill_first = 0
infill_only_where_needed = 0
infill_speed = 20
layer_height = 0.4
min_skirt_length = 20
notes =
only_retract_when_crossing_perimeters = 1
ooze_prevention = 0
output_filename_format = [input_filename_base].gcode
overhangs = 1
perimeter_acceleration = 0
perimeter_extruder = 1
perimeter_extrusion_width = 0
perimeter_speed = 20
perimeters = 3
post_process =
raft_layers = 0
randomize_start = 0
resolution = 0
skirt_distance = 5
skirt_height = 1
skirts = 3
small_perimeter_speed = 20
solid_fill_pattern = rectilinear
solid_infill_below_area = 20
solid_infill_every_layers = 0
solid_infill_extrusion_width = 0
solid_infill_speed = 20
spiral_vase = 0
standby_temperature_delta = -5
start_perimeters_at_concave_points = 0
start_perimeters_at_non_overhang = 0
support_material =
support_material_angle = 0
support_material_enforce_layers = 0
support_material_extruder = 1
support_material_extrusion_width = 0
support_material_interface_extruder = 1
support_material_interface_layers = 1
support_material_interface_spacing = 1
support_material_pattern = rectilinear
support_material_spacing = 5
support_material_speed = 20
support_material_threshold = 60
thin_walls = 1
threads = 4
top_infill_extrusion_width = 0
top_solid_infill_speed = 20
top_solid_layers = 4
travel_speed = 100
bed_size = 86,100
end_gcode = M104 S0 ; turn off temperature\nG1 X0 Y0 F5000 ; move to x0, y0\nG91 ; relative positioning\nG1 Z+10 ; move print head up 10mm\nM84 ; disable motors\nG90 ; absolute positioning
extruder_offset = 0x0
gcode_flavor = reprap
layer_gcode =
nozzle_diameter = 0.4
print_center = 43,50
retract_before_travel = 2
retract_layer_change = 1
retract_length = 3
retract_length_toolchange = 0
retract_lift = 0
retract_restart_extra = 0.1
retract_restart_extra_toolchange = 0
retract_speed = 30
start_gcode = G92 X0 Y0 Z0\nG1 Z5 F5000 ; lift nozzle
toolchange_gcode =
use_firmware_retraction = 0
use_relative_e_distances =
vibration_limit = 3
wipe =
z_offset = 0
bed_temperature = 0
bridge_fan_speed = 100
cooling = 1
disable_fan_first_layers = 1
extrusion_multiplier = 1.1
fan_always_on = 0
fan_below_layer_time = 60
filament_diameter = 1.75
first_layer_bed_temperature = 0
first_layer_temperature = 225
max_fan_speed = 100
min_fan_speed = 35
min_print_speed = 15
slowdown_below_layer_time = 15
temperature = 225