Advertisement
Not a member of Pastebin yet?
Sign Up,
it unlocks many cool features!
- U-Boot SPL 2013.04-dirty (Jul 10 2013 - 14:02:53)
- Incorrect magic number (0xffffffff) in EEPROM
- Could not get board ID.
- Unknown board, assuming Beaglebone LT/Black.musb-hdrc: ConfigData=0xde (UTMI-8, dyn FIFOs, HB-ISO Rx, HB-ISO Tx, SoftConn)
- musb-hdrc: MHDRC RTL version 2.0
- musb-hdrc: setup fifo_mode 4
- musb-hdrc: 28/31 max ep, 16384/16384 memory
- USB Peripheral mode controller at 47401000 using PIO, IRQ 0
- musb-hdrc: ConfigData=0xde (UTMI-8, dyn FIFOs, HB-ISO Rx, HB-ISO Tx, SoftConn)
- musb-hdrc: MHDRC RTL version 2.0
- musb-hdrc: setup fifo_mode 4
- musb-hdrc: 28/31 max ep, 16384/16384 memory
- USB Host mode controller at 47401800 using PIO, IRQ 0
- OMAP SD/MMC: 0
- reading u-boot.img
- reading u-boot.img
- U-Boot 2013.04-dirty (Jul 10 2013 - 14:02:53)
- I2C: ready
- DRAM: 256 MiB
- WARNING: Caches not enabled
- Incorrect magic number (0xffffffff) in EEPROM
- Could not get board ID.
- NAND: No NAND device found!!!
- 0 MiB
- MMC: OMAP SD/MMC: 0, OMAP SD/MMC: 1
- *** Warning - readenv() failed, using default environment
- musb-hdrc: ConfigData=0xde (UTMI-8, dyn FIFOs, HB-ISO Rx, HB-ISO Tx, SoftConn)
- musb-hdrc: MHDRC RTL version 2.0
- musb-hdrc: setup fifo_mode 4
- musb-hdrc: 28/31 max ep, 16384/16384 memory
- USB Peripheral mode controller at 47401000 using PIO, IRQ 0
- musb-hdrc: ConfigData=0xde (UTMI-8, dyn FIFOs, HB-ISO Rx, HB-ISO Tx, SoftConn)
- musb-hdrc: MHDRC RTL version 2.0
- musb-hdrc: setup fifo_mode 4
- musb-hdrc: 28/31 max ep, 16384/16384 memory
- USB Host mode controller at 47401800 using PIO, IRQ 0
- Net: <ethaddr> not set. Validating first E-fuse MAC
- Phy not found
- PHY reset timed out
- cpsw, usb_ether
- Hit any key to stop autoboot: 1 0
- gpio: pin 53 (gpio 53) value is 1
- mmc0 is current device
- micro SD card found
- mmc0 is current device
- gpio: pin 54 (gpio 54) value is 1
- SD/MMC found on device 0
- reading uEnv.txt
- 43 bytes read in 3 ms (13.7 KiB/s)
- Loaded environment from uEnv.txt
- Importing environment from mmc ...
- gpio: pin 55 (gpio 55) value is 1
- 4385024 bytes read in 773 ms (5.4 MiB/s)
- gpio: pin 56 (gpio 56) value is 1
- 24808 bytes read in 50 ms (484.4 KiB/s)
- Booting from mmc ...
- ## Booting kernel from Legacy Image at 80007fc0 ...
- Image Name: Angstrom/3.8.13/beaglebone
- Image Type: ARM Linux Kernel Image (uncompressed)
- Data Size: 4384960 Bytes = 4.2 MiB
- Load Address: 80008000
- Entry Point: 80008000
- Verifying Checksum ... OK
- ## Flattened Device Tree blob at 80f80000
- Booting using the fdt blob at 0x80f80000
- XIP Kernel Image ... OK
- OK
- Using Device Tree in place at 80f80000, end 80f890e7
- Starting kernel ...
- Uncompressing Linux... done, booting the kernel.
- [ 0.572787] omap2_mbox_probe: platform not supported
- [ 0.583402] tps65217-bl tps65217-bl: no platform data provided
- [ 0.629252] bone-capemgr bone_capemgr.8: bone: Invalid signature 'ffffffff' at baseboard
- [ 0.637752] bone-capemgr bone_capemgr.8: Failed to scan baseboard eeprom
- [ 0.662576] omap_hsmmc mmc.4: of_parse_phandle_with_args of 'reset' failed
- [ 0.697795] pinctrl-single 44e10800.pinmux: pin 44e10854 already requested by 44e10800.pinmux; cannot claim for gpio-leds.7
- [ 0.709529] pinctrl-single 44e10800.pinmux: pin-21 (gpio-leds.7) status -22
- [ 0.716838] pinctrl-single 44e10800.pinmux: could not request pin 21 on device pinctrl-single
- systemd-fsck[78]: Angstrom: clean, 60084/218160 files, 415628/872448 blocks
- .---O---.
- | | .-. o o
- | | |-----.-----.-----.| | .----..-----.-----.
- | | | __ | ---'| '--.| .-'| | |
- | | | | | |--- || --'| | | ' | | | |
- '---'---'--'--'--. |-----''----''--' '-----'-'-'-'
- -' |
- '---'
- The Angstrom Distribution beaglebone ttyO0
- Angstrom v2012.12 - Kernel 3.8.13
- beaglebone login: [ 8.261852] libphy: PHY 4a101000.mdio:00 not found
- [ 8.266951] net eth0: phy 4a101000.mdio:00 not found on slave 0
Advertisement
Add Comment
Please, Sign In to add comment
Advertisement