Advertisement
Not a member of Pastebin yet?
Sign Up,
it unlocks many cool features!
- BootROM - 1.73
- Booting from MMC
- General initialization - Version: 1.0.0
- Detected Device ID 6828
- High speed PHY - Version: 2.0
- Init Customer board board SerDes lanes topology details:
- | Lane # | Speed| Type |
- ------------------------------|
- | 0 | 3 | SATA0 |
- | 1 | 0 | SGMII1 |
- | 2 | 5 | PCIe1 |
- | 3 | 5 | USB3 HOST1 |
- | 4 | 5 | PCIe2 |
- | 5 | 0 | SGMII2 |
- -------------------------------
- PCIe, Idx 1: detected no link
- PCIe, Idx 2: detected no link
- High speed PHY - Ended Successfully
- DDR3 Training Sequence - Ver TIP-1.39.0
- DDR3 Training Sequence - Switching XBAR Window to FastPath Window
- DDR3 Training Sequence - Ended Successfully
- BootROM: Image checksum verification PASSED
- __ __ _ _
- | \/ | __ _ _ ____ _____| | |
- | |\/| |/ _` | '__\ \ / / _ \ | |
- | | | | (_| | | \ V / __/ | |
- |_| |_|\__,_|_| \_/ \___|_|_|
- _ _ ____ _
- | | | | | __ ) ___ ___ | |_
- | | | |___| _ \ / _ \ / _ \| __|
- | |_| |___| |_) | (_) | (_) | |_
- \___/ |____/ \___/ \___/ \__|
- ** LOADER **
- U-Boot 2013.01 (Jan 09 2016 - 14:20:19) Marvell version: 2015_T1.0p11
- Board: A38x-Customer-Board-1
- SoC: MV88F6828 Rev A0
- running 2 CPUs
- CPU: ARM Cortex A9 MPCore (Rev 1) LE
- CPU 0
- CPU @ 1600 [MHz]
- L2 @ 800 [MHz]
- TClock @ 250 [MHz]
- DDR3 @ 800 [MHz]
- DDR3 32 Bit Width,FastPath Memory Access, DLB Enabled, ECC Disabled
- DRAM: 1 GiB
- MMC: mv_sdh: 0
- *** Warning - bad CRC, using default environment
- PCI-e 0: Detected No Link.
- PCI-e 1: Detected No Link.
- USB2.0 0: Host Mode
- USB3.0 0: Host Mode
- USB3.0 1: Host Mode
- Map: Code: 0x3fed3000:0x3ff9762c
- BSS: 0x3ffef164
- Stack: 0x3f9c2f20
- Heap: 0x3f9c3000:0x3fed3000
- U-Boot Environment: 0x000f0000:0x00100000 (MMC)
- Board configuration detected:
- Net:
- | port | Interface | PHY address |
- |--------|-----------|--------------|
- | egiga0 | RGMII | 0x00 |
- | egiga1 | SGMII | In-Band |
- | egiga2 | SGMII | In-Band |
- egiga0 [PRIME], egiga1, egiga2
- Hit any key to stop autoboot: 0
- 322 bytes read in 29 ms (10.7 KiB/s)
- ## Executing script at 03000000
- 15128 bytes read in 26 ms (567.4 KiB/s)
- 5175752 bytes read in 288 ms (17.1 MiB/s)
- ## Flattened Device Tree blob at 01000000
- Booting using the fdt blob at 0x01000000
- Loading Device Tree to 00ff9000, end 00fffb17 ... OK
- Skipping Device Tree update ('fdt_skip_update' = yes)
- Limit DDR size at 3GB due to power of 2 requirement of Address decoding
- Starting kernel ...
- Uncompressing Linux... done, booting the kernel.
- Welcome to Debian GNU/Linux 8 (jessie)!
- Expecting device dev-ttyS0.device...
- [ OK ] Reached target Remote File Systems (Pre).
- [ OK ] Reached target Paths.
- [ OK ] Reached target Encrypted Volumes.
- [ OK ] Reached target Swap.
- [ OK ] Created slice Root Slice.
- [ OK ] Created slice User and Session Slice.
- [ OK ] Listening on /dev/initctl Compatibility Named Pipe.
- [ OK ] Listening on Delayed Shutdown Socket.
- [ OK ] Listening on Journal Socket (/dev/log).
- [ OK ] Listening on udev Control Socket.
- [ OK ] Listening on udev Kernel Socket.
- [ OK ] Listening on Journal Socket.
- [ OK ] Created slice System Slice.
- [ OK ] Created slice system-getty.slice.
- [ OK ] Created slice system-serial\x2dgetty.slice.
- Starting Increase datagram queue length...
- Starting Restore / save the current clock...
- Starting Load Kernel Modules...
- Starting udev Coldplug all Devices...
- Mounting POSIX Message Queue File System...
- Mounting Debug File System...
- Starting Create list of required static device nodes...rrent kernel...
- Starting LSB: Set keymap...
- [ OK ] Reached target Slices.
- [ OK ] Mounted Debug File System.
- [ OK ] Mounted POSIX Message Queue File System.
- [ OK ] Started Increase datagram queue length.
- [ OK ] Started Restore / save the current clock.
- [FAILED] Failed to start Load Kernel Modules.
- See 'systemctl status systemd-modules-load.service' for details.
- [ OK ] Started Create list of required static device nodes ...current kernel.
- [ OK ] Started LSB: Set keymap.
- [ OK ] Started udev Coldplug all Devices.
- Starting Create Static Device Nodes in /dev...
- Starting Apply Kernel Variables...
- [ OK ] Listening on Syslog Socket.
- Starting Journal Service...
- [ OK ] Started Journal Service.
- [ OK ] Started Create Static Device Nodes in /dev.
- [ OK ] Started Apply Kernel Variables.
- Starting udev Kernel Device Manager...
- [ OK ] Started udev Kernel Device Manager.
- Starting Copy rules generated while the root was ro...
- Starting LSB: Set preliminary keymap...
- Starting LSB: Tune IDE hard disks...
- [ OK ] Started Copy rules generated while the root was ro.
- [ OK ] Started LSB: Tune IDE hard disks.
- [ OK ] Found device /dev/ttyS0.
- [ OK ] Started LSB: Set preliminary keymap.
- Starting Remount Root and Kernel File Systems...
- [ OK ] Started Remount Root and Kernel File Systems.
- Starting Various fixups to make systemd work better on Debian...
- Starting Load/Save Random Seed...
- [ OK ] Reached target Local File Systems (Pre).
- Mounting /tmp...
- [ OK ] Started Various fixups to make systemd work better on Debian.
- [ OK ] Started Load/Save Random Seed.
- [ OK ] Mounted /tmp.
- [ OK ] Reached target Local File Systems.
- Starting Create Volatile Files and Directories...
- [ OK ] Reached target Remote File Systems.
- Starting Trigger Flushing of Journal to Persistent Storage...
- Starting LSB: Prepare console...
- Starting LSB: Raise network interfaces....
- [ OK ] Started Create Volatile Files and Directories.
- Starting Update UTMP about System Boot/Shutdown...
- [ OK ] Started Trigger Flushing of Journal to Persistent Storage.
- [ OK ] Started Update UTMP about System Boot/Shutdown.
- [ OK ] Started LSB: Prepare console.
- Starting LSB: Set console font and keymap...
- [ OK ] Started LSB: Set console font and keymap.
- [ OK ] Started LSB: Raise network interfaces..
- [ OK ] Reached target Network.
- [ OK ] Reached target Network is Online.
- [ OK ] Reached target System Initialization.
- [ OK ] Listening on D-Bus System Message Bus Socket.
- [ OK ] Reached target Sockets.
- [ OK ] Reached target Timers.
- [ OK ] Reached target Basic System.
- Starting Entropy daemon using the HAVEGE algorithm...
- [ OK ] Started Entropy daemon using the HAVEGE algorithm.
- Starting Regular background program processing daemon...
- [ OK ] Started Regular background program processing daemon.
- Starting OpenBSD Secure Shell server...
- [ OK ] Started OpenBSD Secure Shell server.
- Starting /etc/rc.local Compatibility...
- Starting Login Service...
- Starting LSB: Get some info about hardware for some ...basic things...
- Starting LSB: Start NTP daemon...
- Starting LSB: disk temperature monitoring daemon...
- Starting LSB: Advanced IEEE 802.11 management daemon...
- Starting LSB: Starts LIRC daemon....
- Starting LSB: Load kernel modules needed to enable cpufreq scaling...
- Starting D-Bus System Message Bus...
- [ OK ] Started D-Bus System Message Bus.
- Starting System Logging Service...
- Starting Permit User Sessions...
- [ OK ] Started /etc/rc.local Compatibility.
- [ OK ] Started LSB: disk temperature monitoring daemon.
- [ OK ] Started LSB: Advanced IEEE 802.11 management daemon.
- [ OK ] Started LSB: Start NTP daemon.
- [ OK ] Started LSB: Starts LIRC daemon..
- [ OK ] Started LSB: Load kernel modules needed to enable cpufreq scaling.
- [ OK ] Started Permit User Sessions.
- [ OK ] Started System Logging Service.
- [ OK ] Started Login Service.
- Starting LSB: set CPUFreq kernel parameters...
- Starting Getty on tty1...
- [ OK ] Started Getty on tty1.
- Starting Serial Getty on ttyS0...
- [ OK ] Started Serial Getty on ttyS0.
- [ OK ] Reached target Login Prompts.
- [ OK ] Started LSB: set CPUFreq kernel parameters.
- Starting LSB: Set sysfs variables from /etc/sysfs.conf...
- [ OK ] Started LSB: Set sysfs variables from /etc/sysfs.conf.
- [ OK ] Started LSB: Get some info about hardware for some A...e basic things.
- Starting LSB: Script to run when first starting...
- Debian GNU/Linux 8 armada ttyS0
- armada login: root
- Password:
- You are required to change your password immediately (root enforced)
- Changing password for root.
- (current) UNIX password:
- Enter new UNIX password:
- Retype new UNIX password:
- Last login: Sat Jan 9 15:01:33 CET 2016 on ttyS0
- Linux armada 3.10.94-marvell #8 SMP Sat Jan 9 14:35:30 CET 2016 armv7l
- Load: 0.04, 0.10, 0.05 - Board: 57.9?°C - Memory: 963Mb
- root@armada:~#
Advertisement
Add Comment
Please, Sign In to add comment
Advertisement