Advertisement
Not a member of Pastebin yet?
Sign Up,
it unlocks many cool features!
- Terminal ready
- U-Boot SPL 2013.10-rc3-00001-g0db8b57 (Sep 18 2013 - 15:10:34)
- reading u-boot.img
- reading u-boot.img
- U-Boot 2013.10-rc3-00001-g0db8b57 (Sep 18 2013 - 15:10:34)
- OMAP36XX/37XX-GP ES1.2, CPU-OPP2, L3-200MHz, Max CPU Clock 1 Ghz
- OMAP3 Beagle board + LPDDR/NAND
- I2C: ready
- DRAM: 512 MiB
- NAND: 0 MiB
- MMC: OMAP SD/MMC: 0
- *** Warning - readenv() failed, using default environment
- In: serial
- Out: serial
- Err: serial
- Beagle xM Rev C
- No EEPROM on expansion board
- Die ID #409600029ff800000168300f0d00c008
- Net: usb_ether
- Hit any key to stop autoboot: 3 2 1 0
- mmc0 is current device
- gpio: pin 173 (gpio 173) value is 0
- gpio: pin 4 (gpio 4) value is 0
- SD/MMC found on device 0
- reading uEnv.txt
- 732 bytes read in 4 ms (178.7 KiB/s)
- Loaded environment from uEnv.txt
- Importing environment from mmc ...
- Running uenvcmd ...
- (Re)start USB...
- USB0: ULPI: ulpi_reset: failed writing reset bit
- ULPI: ulpi_reset: failed writing reset bit
- USB EHCI 1.00
- scanning bus 0 for devices... 3 USB Device(s) found
- scanning usb for storage devices... 0 Storage Device(s) found
- scanning usb for ethernet devices... 1 Ethernet Device(s) found
- usbethaddr=08:00:28:01:1b:2f
- ++1
- ERROR: Need valid 'usbnet_devaddr' to be set
- at ether.c:2357/usb_eth_init()
- Waiting for Ethernet connection... done.
- BOOTP broadcast 1
- *** Unhandled DHCP Option in OFFER/ACK: 44
- *** Unhandled DHCP Option in OFFER/ACK: 46
- *** Unhandled DHCP Option in OFFER/ACK: 150
- *** Unhandled DHCP Option in OFFER/ACK: 44
- *** Unhandled DHCP Option in OFFER/ACK: 46
- *** Unhandled DHCP Option in OFFER/ACK: 150
- DHCP client bound to address x.y.91.118
- Using sms0 device
- TFTP from server x.y.91.59; our IP address is x.y.91.118
- Filename '/tftpboot/kernel/omap3-beagle-xm.dtb'.
- Load address: 0x80f80000
- Loading: *###########
- 545.9 KiB/s
- done
- Bytes transferred = 52021 (cb35 hex)
- ++2
- ++3
- Waiting for Ethernet connection... done.
- BOOTP broadcast 1
- *** Unhandled DHCP Option in OFFER/ACK: 44
- *** Unhandled DHCP Option in OFFER/ACK: 46
- *** Unhandled DHCP Option in OFFER/ACK: 150
- *** Unhandled DHCP Option in OFFER/ACK: 44
- *** Unhandled DHCP Option in OFFER/ACK: 46
- *** Unhandled DHCP Option in OFFER/ACK: 150
- DHCP client bound to address x.y.91.118
- Using sms0 device
- TFTP from server x.y.91.59; our IP address is x.y.91.118
- Filename '/tftpboot/kernel/zImage'.
- Load address: 0x80200000
- Loading: *#################################################################
- #################################################################
- #################################################################
- #################################################################
- #################################################################
- #################################################################
- #################################################################
- #################################################################
- #################################################################
- #################################################################
- #################################################################
- #################################################################
- #######################################
- 554.7 KiB/s
- done
- Bytes transferred = 4190264 (3ff038 hex)
- ++4
- stopping USB..
- Kernel image @ 0x80200000 [ 0x000000 - 0x3ff038 ]
- ## Flattened Device Tree blob at 80f80000
- Booting using the fdt blob at 0x80f80000
- Using Device Tree in place at 80f80000, end 80f8fb34
- Starting kernel ...
- [ 0.000000] Booting Linux on physical CPU 0x0
- [ 0.000000] Linux version 3.12.0-rc5-00171-ge348c9e (nmenon@kahuna) (gcc version 4.6.3 (Ubuntu/Linaro 4.6.3-1ubuntu5) ) #4 SMP Wed Oct 16 09:44:41 CDT 2013
- [ 0.000000] CPU: ARMv7 Processor [413fc082] revision 2 (ARMv7), cr=10c53c7d
- [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
- [ 0.000000] Machine: Generic OMAP36xx (Flattened Device Tree), model: TI OMAP3 BeagleBoard xM
- [ 0.000000] cma: CMA: reserved 16 MiB at 9e800000
- [ 0.000000] Memory policy: ECC disabled, Data cache writeback
- [ 0.000000] CPU: All CPU(s) started in SVC mode.
- [ 0.000000] OMAP3630 ES1.2 (l2cache iva sgx neon isp 192mhz_clk )
- [ 0.000000] PERCPU: Embedded 9 pages/cpu @c13ac000 s14656 r8192 d14016 u36864
- [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 129792
- [ 0.000000] Kernel command line: console=ttyO2,115200n8 mpurate=auto buddy=none camera=none vram=12M omapfb.mode=dvi:640x480MR-16@60 omapdss.def_disp=dvi root=/dev/mmcblk0p2 rw rootfstype=ext3 rootwait earlyprintk
- [ 0.000000] PID hash table entries: 2048 (order: 1, 8192 bytes)
- [ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
- [ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
- [ 0.000000] Memory: 487976K/523264K available (5430K kernel code, 659K rwdata, 2100K rodata, 410K init, 5524K bss, 35288K reserved, 0K highmem)
- [ 0.000000] Virtual kernel memory layout:
- [ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB)
- [ 0.000000] fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB)
- [ 0.000000] vmalloc : 0xe0800000 - 0xff000000 ( 488 MB)
- [ 0.000000] lowmem : 0xc0000000 - 0xe0000000 ( 512 MB)
- [ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB)
- [ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB)
- [ 0.000000] .text : 0xc0008000 - 0xc0762a24 (7531 kB)
- [ 0.000000] .init : 0xc0763000 - 0xc07c9940 ( 411 kB)
- [ 0.000000] .data : 0xc07ca000 - 0xc086ef88 ( 660 kB)
- [ 0.000000] .bss : 0xc086ef88 - 0xc0dd3fa8 (5525 kB)
- [ 0.000000] Hierarchical RCU implementation.
- [ 0.000000] RCU restricting CPUs from NR_CPUS=2 to nr_cpu_ids=1.
- [ 0.000000] NR_IRQS:16 nr_irqs:16 16
- [ 0.000000] IRQ: Found an INTC at 0xfa200000 (revision 4.0) with 96 interrupts
- [ 0.000000] Total of 96 interrupts on 1 active controller
- [ 0.000000] Clocking rate (Crystal/Core/MPU): 26.0/400/600 MHz
- [ 0.000000] clock: dpll5_ck failed transition to 'bypassed'
- [ 0.000000] OMAP clockevent source: timer1 at 32768 Hz
- [ 0.000000] sched_clock: 32 bits at 32kHz, resolution 30517ns, wraps every 131071999ms
- [ 0.000000] OMAP clocksource: 32k_counter at 32768 Hz
- [ 0.000000] Console: colour dummy device 80x30
- [ 0.000000] Lock dependency validator: Copyright (c) 2006 Red Hat, Inc., Ingo Molnar
- [ 0.000000] ... MAX_LOCKDEP_SUBCLASSES: 8
- [ 0.000000] ... MAX_LOCK_DEPTH: 48
- [ 0.000000] ... MAX_LOCKDEP_KEYS: 8191
- [ 0.000000] ... CLASSHASH_SIZE: 4096
- [ 0.000000] ... MAX_LOCKDEP_ENTRIES: 16384
- [ 0.000000] ... MAX_LOCKDEP_CHAINS: 32768
- [ 0.000000] ... CHAINHASH_SIZE: 16384
- [ 0.000000] memory used by lock dependency info: 3695 kB
- [ 0.000000] per task-struct memory footprint: 1152 bytes
- [ 0.001281] Calibrating delay loop... 395.67 BogoMIPS (lpj=1978368)
- [ 0.109680] pid_max: default: 32768 minimum: 301
- [ 0.110168] Security Framework initialized
- [ 0.110351] Mount-cache hash table entries: 512
- [ 0.163452] CPU: Testing write buffer coherency: ok
- [ 0.165100] CPU0: thread -1, cpu 0, socket -1, mpidr 0
- [ 0.165191] Setting up static identity map for 0xc05257f8 - 0xc0525868
- [ 0.168853] Brought up 1 CPUs
- [ 0.168884] SMP: Total of 1 processors activated.
- [ 0.168914] CPU: All CPU(s) started in SVC mode.
- [ 0.172668] devtmpfs: initialized
- [ 0.183227] VFP support v0.3: implementor 41 architecture 3 part 30 variant c rev 3
- [ 0.196624] omap_hwmod: usb_host_hs: could not associate to clkdm l3_init_clkdm
- [ 0.197021] omap_hwmod: usb_tll_hs: could not associate to clkdm l3_init_clkdm
- [ 0.254547] pinctrl core: initialized pinctrl subsystem
- [ 0.259704] regulator-dummy: no parameters
- [ 0.270202] NET: Registered protocol family 16
- [ 0.278594] DMA: preallocated 256 KiB pool for atomic coherent allocations
- [ 0.295623] Reprogramming SDRC clock to 400000000 Hz
- [ 0.305053] omap_gpio 48310000.gpio: could not find pctldev for node /ocp/pinmux@48002a00/pinmux_gpio1_pins, deferring probe
- [ 0.305114] platform 48310000.gpio: Driver omap_gpio requests probe deferral
- [ 0.310516] OMAP GPIO hardware version 2.5
- [ 0.338867] platform 49022000.mcbsp: alias fck already exists
- [ 0.340454] platform 49024000.mcbsp: alias fck already exists
- [ 0.357482] omap-gpmc 6e000000.gpmc: GPMC revision 5.0
- [ 0.364593] No ATAGs?
- [ 0.364624] hw-breakpoint: debug architecture 0x4 unsupported.
- [ 0.370361] OMAP DMA hardware revision 5.0
- [ 0.448638] bio: create slab <bio-0> at 0
- [ 0.454040] edma-dma-engine edma-dma-engine.0: Can't allocate PaRAM dummy slot
- [ 0.454101] edma-dma-engine: probe of edma-dma-engine.0 failed with error -5
- [ 0.546081] omap-dma-engine 48056000.dma-controller: OMAP DMA engine driver
- [ 0.547637] platform hsusb2_power_reg.22: Driver reg-fixed-voltage requests probe deferral
- [ 0.558044] SCSI subsystem initialized
- [ 0.560974] usbcore: registered new interface driver usbfs
- [ 0.561553] usbcore: registered new interface driver hub
- [ 0.562255] usbcore: registered new device driver usb
- [ 0.563018] platform hsusb2_phy.23: Driver usb_phy_gen_xceiv requests probe deferral
- [ 0.571289] omap_i2c i2c.8: bus 0 rev4.4 at 2600 kHz
- [ 0.573028] omap_i2c i2c.9: bus 1 rev4.4 at 400 kHz
- [ 0.575836] omap_i2c i2c.10: bus 2 rev4.4 at 100 kHz
- [ 0.586181] Switched to clocksource 32k_counter
- [ 0.774230] NET: Registered protocol family 2
- [ 0.776763] TCP established hash table entries: 4096 (order: 3, 32768 bytes)
- [ 0.777099] TCP bind hash table entries: 4096 (order: 5, 147456 bytes)
- [ 0.779357] TCP: Hash tables configured (established 4096 bind 4096)
- [ 0.779602] TCP: reno registered
- [ 0.779632] UDP hash table entries: 256 (order: 2, 20480 bytes)
- [ 0.779937] UDP-Lite hash table entries: 256 (order: 2, 20480 bytes)
- [ 0.781707] NET: Registered protocol family 1
- [ 0.784027] RPC: Registered named UNIX socket transport module.
- [ 0.784057] RPC: Registered udp transport module.
- [ 0.784088] RPC: Registered tcp transport module.
- [ 0.784088] RPC: Registered tcp NFSv4.1 backchannel transport module.
- [ 0.785278] NetWinder Floating Point Emulator V0.97 (double precision)
- [ 0.785522] hw perfevents: enabled with ARMv7 Cortex-A8 PMU driver, 5 counters available
- [ 1.014190] VFS: Disk quotas dquot_6.5.2
- [ 1.014526] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
- [ 1.017944] NFS: Registering the id_resolver key type
- [ 1.018463] Key type id_resolver registered
- [ 1.018493] Key type id_legacy registered
- [ 1.018646] jffs2: version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, Inc.
- [ 1.019256] msgmni has been set to 985
- [ 1.023742] io scheduler noop registered
- [ 1.023773] io scheduler deadline registered
- [ 1.023834] io scheduler cfq registered (default)
- [ 1.028808] pinctrl-single 48002030.pinmux: 742 pins at pa fa002030 size 1484
- [ 1.029663] pinctrl-single 48002a00.pinmux: 46 pins at pa fa002a00 size 92
- [ 1.035339] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
- [ 1.045989] serial.5: ttyO0 at MMIO 0x4806a000 (irq = 88, base_baud = 3000000) is a OMAP UART0
- [ 1.049163] serial.6: ttyO1 at MMIO 0x4806c000 (irq = 89, base_baud = 3000000) is a OMAP UART1
- [ 1.051513] serial.7: ttyO2 at MMIO 0x49020000 (irq = 90, base_baud = 3000000) is a OMAP UART2
- [ 1.800720] console [ttyO2] enabled
- [ 1.807067] serial.17: ttyO3 at MMIO 0x49042000 (irq = 96, base_baud = 3000000) is a OMAP UART3
- [ 1.854949] brd: module loaded
- [ 1.882568] loop: module loaded
- [ 1.900085] twl 0-0048: PIH (irq 23) chaining IRQs 306..314
- [ 1.906738] twl 0-0048: power (irq 311) chaining IRQs 314..321
- [ 1.920013] VDD1: 600 <--> 1450 mV at 1200 mV
- [ 1.928314] VDAC: 1800 mV
- [ 1.934234] VPLL2: 1800 mV
- [ 1.940460] VMMC1: 1850 <--> 3150 mV at 3150 mV
- [ 1.948730] VMMC2: 1850 <--> 3150 mV at 2600 mV
- [ 1.956481] VUSB1V5: 1500 mV
- [ 1.962005] VUSB1V8: 1800 mV
- [ 1.967681] VUSB3V1: 3100 mV
- [ 1.973510] VSIM: 1800 <--> 3000 mV at 1800 mV
- [ 1.981781] twl4030_gpio gpio.36: gpio (irq 306) chaining IRQs 322..339
- [ 2.003570] mtdoops: mtd device (mtddev=name/number) must be supplied
- [ 2.028747] usbcore: registered new interface driver asix
- [ 2.035034] usbcore: registered new interface driver ax88179_178a
- [ 2.042724] usbcore: registered new interface driver cdc_ether
- [ 2.050933] usbcore: registered new interface driver r815x
- [ 2.057586] usbcore: registered new interface driver smsc95xx
- [ 2.064208] usbcore: registered new interface driver net1080
- [ 2.070922] usbcore: registered new interface driver cdc_subset
- [ 2.077880] usbcore: registered new interface driver zaurus
- [ 2.084411] usbcore: registered new interface driver cdc_ncm
- [ 2.093231] usbcore: registered new interface driver cdc_wdm
- [ 2.100189] usbcore: registered new interface driver usb-storage
- [ 2.107452] usbcore: registered new interface driver usbtest
- [ 2.117980] mousedev: PS/2 mouse device common for all mice
- [ 2.131072] twl_rtc rtc.25: Power up reset detected.
- [ 2.136840] twl_rtc rtc.25: Enabling TWL-RTC
- [ 2.147094] twl_rtc rtc.25: rtc core: registered rtc.25 as rtc0
- [ 2.155364] i2c /dev entries driver
- [ 2.163940] Driver for 1-wire Dallas network protocol.
- [ 2.175903] omap_wdt: OMAP Watchdog Timer Rev 0x31: initial timeout 60 sec
- [ 2.191925] omap-dma-engine 48056000.dma-controller: allocating channel for 62
- [ 2.199951] omap-dma-engine 48056000.dma-controller: allocating channel for 61
- [ 2.211181] omap_hsmmc mmc.15: pins are not configured from the driver
- [ 2.269958] ledtrig-cpu: registered to indicate activity on CPUs
- [ 2.280761] usbcore: registered new interface driver usbhid
- [ 2.286834] usbhid: USB HID core driver
- [ 2.294281] oprofile: using arm/armv7
- [ 2.299316] TCP: cubic registered
- [ 2.302825] Initializing XFRM netlink socket
- [ 2.307556] NET: Registered protocol family 17
- [ 2.312377] NET: Registered protocol family 15
- [ 2.317596] Key type dns_resolver registered
- [ 2.328552] ThumbEE CPU extension supported.
- [ 2.338287] VUSB3V1: disabling
- [ 2.343444] VPLL2: disabling
- [ 2.347900] VDAC: disabling
- [ 2.362396] mmc0: host does not support reading read-only switch. assuming write-enable.
- [ 2.371673] hsusb2_vbus: 3300 mV
- [ 2.377319] mmc0: new high speed SDHC card at address 1234
- [ 2.389282] mmcblk0: mmc0:1234 SA04G 3.63 GiB
- [ 2.402130] input: gpio_keys.21 as /devices/gpio_keys.21/input/input0
- [ 2.411132] mmcblk0: p1 p2
- [ 2.422943] twl_rtc rtc.25: setting system clock to 2000-01-01 00:00:00 UTC (946684800)
- [ 8.382904] kjournald starting. Commit interval 5 seconds
- [ 9.108795] EXT3-fs (mmcblk0p2): using internal journal
- [ 9.119903] EXT3-fs (mmcblk0p2): recovery complete
- [ 9.124969] EXT3-fs (mmcblk0p2): mounted filesystem with ordered data mode
- [ 9.132507] VFS: Mounted root (ext3 filesystem) on device 179:2.
- [ 9.145111] devtmpfs: mounted
- [ 9.149353] Freeing unused kernel memory: 408K (c0763000 - c07c9000)
- Mounting proc : OK
- Mounting sysfs : OK
- Mounting devtmpfs:mount: mounting none on /dev failed: Device or resource busy
- boot mounted: OK
- /dev/ttyO2 linked to /dev/tty-bd - using as console
- ******************************************
- Starting System Init for GenericOMAP36xx(FlattenedDeviceTree)
- Release: X.x
- Kernel: Linux GenericOMAP36xx(FlattenedDeviceTree) 3.12.0-rc5-00171-ge348c9e #4 SMP Wed Oct 16 09:44:41 CDT 2013 armv7l GNU/Linux
- ******************************************
- Saving kernel ring buffer : OK
- Mounting devpts : OK
- Setting up networking
- Configuring lo : OK
- Starting syslogd : OK
- Starting klogd : OK
- Mounting filesystems : OK
- mount: mounting none on /proc/bus/usb/ failed: No such file or directory
- Please press Enter to activate this console.
- / $
- ./dvfs-basic./ $
- / $ cd pm-test-scripts/
- /pm-test-scripts $ ./dvfs-basic.sh
- ===================
- System CPUFREQ Configuration:
- ===================
- Scaling driver: generic_cpu0
- Scaling Regulator: /sys/class/regulator/regulator.1 : VDD1
- 300000 600000 800000 are the available frequencies
- ===================
- Boot Configuration:
- ===================
- bogomips@ boot:
- Boot scaling frequency =600000
- Boot VDD1 Scaling voltage(uV) =1200000
- ===================
- Single OPP transition walk through test:
- ===================
- 1: TESTING for 1 seconds at 300000
- current scaling frequency(for 300000) =300000
- current VDD1 Scaling voltage(uV) =1012500
- bogomips@ frequency 300000:
- 2: TESTING for 1 seconds at 600000
- current scaling frequency(for 600000) =600000
- current VDD1 Scaling voltage(uV) =1200000
- bogomips@ frequency 600000:
- 3: TESTING for 1 seconds at 800000
- current scaling frequency(for 800000) =800000
- current VDD1 Scaling voltage(uV) =1325000
- bogomips@ frequency 800000:
- ===================
- Rapid transitions test (print every 1000 all OPP combinations):
- ===================
- [0] 1000: 4 Seconds: Fri Dec 31 18:00:09 CST 1999 : time now = Fri Dec 31 18:00:13 CST 1999
- [1] 1000: 4 Seconds: Fri Dec 31 18:00:09 CST 1999 : time now = Fri Dec 31 18:00:13 CST 1999
- [2] 1000: 4 Seconds: Fri Dec 31 18:00:09 CST 1999 : time now = Fri Dec 31 18:00:13 CST 1999
- [3] 1000: 4 Seconds: Fri Dec 31 18:00:09 CST 1999 : time now = Fri Dec 31 18:00:13 CST 1999
- [4] 1000: 4 Seconds: Fri Dec 31 18:00:09 CST 1999 : time now = Fri Dec 31 18:00:13 CST 1999
- [5] 1000: 4 Seconds: Fri Dec 31 18:00:09 CST 1999 : time now = Fri Dec 31 18:00:13 CST 1999
- [6] 1000: 4 Seconds: Fri Dec 31 18:00:09 CST 1999 : time now = Fri Dec 31 18:00:13 CST 1999
- [7] 1000: 4 Seconds: Fri Dec 31 18:00:09 CST 1999 : time now = Fri Dec 31 18:00:13 CST 1999
- [8] 1000: 4 Seconds: Fri Dec 31 18:00:09 CST 1999 : time now = Fri Dec 31 18:00:13 CST 1999
- [9] 1000: 4 Seconds: Fri Dec 31 18:00:09 CST 1999 : time now = Fri Dec 31 18:00:13 CST 1999
- [10] 1000: 4 Seconds: Fri Dec 31 18:00:09 CST 1999 : time now = Fri Dec 31 18:00:14 CST 1999
- [11] 1000: 5 Seconds: Fri Dec 31 18:00:09 CST 1999 : time now = Fri Dec 31 18:00:14 CST 1999
- [12] 1000: 5 Seconds: Fri Dec 31 18:00:09 CST 1999 : time now = Fri Dec 31 18:00:14 CST 1999
- [13] 1000: 5 Seconds: Fri Dec 31 18:00:09 CST 1999 : time now = Fri Dec 31 18:00:14 CST 1999
- [14] 1000: 5 Seconds: Fri Dec 31 18:00:09 CST 1999 : time now = Fri Dec 31 18:00:14 CST 1999
- [15] 1000: 5 Seconds: Fri Dec 31 18:00:09 CST 1999 : time now = Fri Dec 31 18:00:14 CST 1999
- [16] 1000: 5 Seconds: Fri Dec 31 18:00:09 CST 1999 : time now = Fri Dec 31 18:00:14 CST 1999
- [17] 1000: 5 Seconds: Fri Dec 31 18:00:09 CST 1999 : time now = Fri Dec 31 18:00:14 CST 1999
- [18] 1000: 5 Seconds: Fri Dec 31 18:00:09 CST 1999 : time now = Fri Dec 31 18:00:14 CST 1999
- [19] 1000: 5 Seconds: Fri Dec 31 18:00:09 CST 1999 : time now = Fri Dec 31 18:00:14 CST 1999
- [20] 1000: 5 Seconds: Fri Dec 31 18:00:09 CST 1999 : time now = Fri Dec 31 18:00:14 CST 1999
- [21] 1000: 5 Seconds: Fri Dec 31 18:00:09 CST 1999 : time now = Fri Dec 31 18:00:14 CST 1999
- [22] 1000: 5 Seconds: Fri Dec 31 18:00:09 CST 1999 : time now = Fri Dec 31 18:00:14 CST 1999
- [23] 1000: 5 Seconds: Fri Dec 31 18:00:09 CST 1999 : time now = Fri Dec 31 18:00:14 CST 1999
- [24] 1000: 6 Seconds: Fri Dec 31 18:00:09 CST 1999 : time now = Fri Dec 31 18:00:15 CST 1999
- [25] 1000: 6 Seconds: Fri Dec 31 18:00:09 CST 1999 : time now = Fri Dec 31 18:00:15 CST 1999
- [26] 1000: 6 Seconds: Fri Dec 31 18:00:09 CST 1999 : time now = Fri Dec 31 18:00:15 CST 1999
- [27] 1000: 6 Seconds: Fri Dec 31 18:00:09 CST 1999 : time now = Fri Dec 31 18:00:15 CST 1999
- [28] 1000: 6 Seconds: Fri Dec 31 18:00:09 CST 1999 : time now = Fri Dec 31 18:00:15 CST 1999
- [29] 1000: 6 Seconds: Fri Dec 31 18:00:09 CST 1999 : time now = Fri Dec 31 18:00:15 CST 1999
- [30] 1000: 6 Seconds: Fri Dec 31 18:00:09 CST 1999 : time now = Fri Dec 31 18:00:15 CST 1999
- [31] 1000: 6 Seconds: Fri Dec 31 18:00:09 CST 1999 : time now = Fri Dec 31 18:00:15 CST 1999
- [32] 1000: 6 Seconds: Fri Dec 31 18:00:09 CST 1999 : time now = Fri Dec 31 18:00:15 CST 1999
- ^CTest start: Fri Dec 31 18:00:09 CST 1999 now: Fri Dec 31 18:00:15 CST 1999
- Test start: Fri Dec 31 18:00:09 CST 1999 now: Fri Dec 31 18:00:15 CST 1999
- /pm-test-scripts $
- Skipping tty reset...
- Thanks for using picocom
- picocom v1.4
- port is : /dev/ttyUSB2
- flowcontrol : none
- baudrate is : 115200
- parity is : none
- databits are : 8
- escape is : C-a
- noinit is : yes
- noreset is : yes
- nolock is : yes
- send_cmd is : ascii_xfr -s -v -l10
- receive_cmd is : rz -vv
Advertisement
Add Comment
Please, Sign In to add comment
Advertisement