DDR Version 1.00 20140404
In
SRX
Channel a: DDR3 300MHz
Bus Width=32 Col=10 Bank=8 Row=15 CS=1 Die Bus-Width=16 Size=1024MB
Channel b: DDR3 300MHz
Bus Width=32 Col=10 Bank=8 Row=15 CS=1 Die Bus-Width=16 Size=1024MB
OUT


U-Boot 2014.01-00643-g77f8e4c-dirty (Apr 21 2014 - 15:36:44)

CPU:		RK32xx
arm pll:	1008000000
general pll:	594000000
codec pll:	594000000
ddr pll:	300000000
new pll:	24000000
Board:		RK32xx platform Board
DRAM:		128 MiB
arch_interrupt_init
storage init OK!
Using default environment

In:    serial
Out:   serial
Err:   serial
In:    serial
Out:   serial
Err:   serial
board_late_init
PowerKeyInit start
PowerKeyInit end
charger_init, charger_type = 1, dc_is_charging= 0
pmic_charger_setting charger_type = 1
i2c_set_bus_num: I2C bus = 0
rk_i2c_init: I2C bus = 0
i2c->regs_addr = ff650000,set clk(I2C_CLKDIV: 0x003f003f)
pmic_charger_setting charge ic id = 0xff
GetParam
check parameter success
Unknow param: MACHINE_MODEL:R89!
Unknow param: MACHINE_ID:007!
Unknow param: MANUFACTURER:RK30SDK!
Unknow param: PWR_HLD: 0,0,A,0,1!
partition(uboot): offset=0x00002000, size=0x00002000
partition(misc): offset=0x00004000, size=0x00002000
partition(resource): offset=0x00006000, size=0x00008000
partition(kernel): offset=0x0000E000, size=0x00008000
partition(boot): offset=0x00016000, size=0x00010000
partition(recovery): offset=0x00026000, size=0x00010000
partition(backup): offset=0x00036000, size=0x0001A000
partition(cache): offset=0x00050000, size=0x00040000
partition(kpanic): offset=0x00090000, size=0x00002000
partition(system): offset=0x00092000, size=0x00180000
partition(metadata): offset=0x00212000, size=0x00002000
partition(userdata): offset=0x00214000, size=0x00400000
partition(radical_update): offset=0x00614000, size=0x00020000
partition(user): offset=0x00634000, size=0xFFFFFFFF
empty serial no.
checkKey
vbus = 1
Loaded dtb file:rk-kernel.dtb,load_addr = 0x54df490 size:95917
node:77836 read logo_on switch from dts [0]
rkclk_soft_reset
fix ramdisk_addr:05bf0000
fix kernel_addr:02000000
SecureBootCheckOK:0
 rk_bootm_start
booti: do_bootm_linux...
   Loading Ramdisk to 04f5c000, end 05414787 ... OK
   Loading Device Tree to 04f41000, end 04f5b6ac ... OK

Starting kernel ...

Uncompressing Linux... done, booting the kernel.
Booting Linux on physical CPU 0x500
Linux version 3.17.0-rc1+ (hstuebner@diego) (gcc version 4.7.4 20130613 (release) [ARM/embedded-4_7-branch revision 200083] (GNU Tools for ARM Embedded Processors) ) #1151 SMP Sun Sep 14 12:53:42 CEST 2014
CPU: ARMv7 Processor [410fc0d1] revision 1 (ARMv7), cr=10c5387d
CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
Machine model: netxeon,r89
bootconsole [earlycon0] enabled
Memory policy: Data cache writealloc
PERCPU: Embedded 7 pages/cpu @ee7bf000 s7680 r8192 d12800 u32768
Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 522768
Kernel command line: console=ttyS2,115200 earlyprintk init=/sbin/init root=/dev/mmcblk0p1 rootwait
PID hash table entries: 4096 (order: 2, 16384 bytes)
Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
Memory: 2071580K/2097152K available (4206K kernel code, 203K rwdata, 1348K rodata, 2059K init, 310K bss, 25572K reserved, 1318912K highmem)
Virtual kernel memory layout:
    vector  : 0xffff0000 - 0xffff1000   (   4 kB)
    fixmap  : 0xffc00000 - 0xffe00000   (2048 kB)
    vmalloc : 0xf0000000 - 0xff000000   ( 240 MB)
    lowmem  : 0xc0000000 - 0xef800000   ( 760 MB)
    pkmap   : 0xbfe00000 - 0xc0000000   (   2 MB)
    modules : 0xbf000000 - 0xbfe00000   (  14 MB)
      .text : 0xc0008000 - 0xc0574af8   (5555 kB)
      .init : 0xc0575000 - 0xc0777e00   (2060 kB)
      .data : 0xc0778000 - 0xc07aaf48   ( 204 kB)
       .bss : 0xc07aaf48 - 0xc07f87e0   ( 311 kB)
Hierarchical RCU implementation.
NR_IRQS:16 nr_irqs:16 16
L2C: failed to init: -19
Architected cp15 timer(s) running at 24.00MHz (virt).
sched_clock: 56 bits at 24MHz, resolution 41ns, wraps every 2863311519744ns
Switching to timer-based delay loop, resolution 41ns
Console: colour dummy device 80x30
Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=240000)
pid_max: default: 32768 minimum: 301
Mount-cache hash table entries: 2048 (order: 1, 8192 bytes)
Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes)
CPU: Testing write buffer coherency: ok
CPU0: thread -1, cpu 0, socket 5, mpidr 80000500
Setting up static identity map for 0x3fa688 - 0x3fa6e0
CPU1: failed to boot: -38
CPU2: failed to boot: -38
CPU3: failed to boot: -38
Brought up 1 CPUs
SMP: Total of 1 processors activated.
CPU: All CPU(s) started in SVC mode.
devtmpfs: initialized
VFP support v0.3: implementor 41 architecture 3 part 30 variant d rev 0
pinctrl core: initialized pinctrl subsystem
regulator-dummy: no parameters
NET: Registered protocol family 16
DMA: preallocated 256 KiB pool for atomic coherent allocations
cpuidle: using governor ladder
cpuidle: using governor menu
hw-breakpoint: found 5 (+1 reserved) breakpoint and 4 watchpoint registers.
hw-breakpoint: maximum watchpoint size is 4 bytes.
sys-supply: 5000 mV
sdmmc-supply: 3300 mV
reg-fixed-voltage sdmmc-regulator: Failed to find supply vin
reg-fixed-voltage sdmmc-regulator: Failed to register regulator: -517
platform sdmmc-regulator: Driver reg-fixed-voltage requests probe deferral
vcc_otg: no parameters
vcc_host: no parameters
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
pps_core: LinuxPPS API ver. 1 registered
pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <[email protected]>
PTP clock support registered
Switched to clocksource arch_sys_counter
cfg80211: Calling CRDA to update world regulatory domain
NET: Registered protocol family 2
TCP established hash table entries: 8192 (order: 3, 32768 bytes)
TCP bind hash table entries: 8192 (order: 4, 65536 bytes)
TCP: Hash tables configured (established 8192 bind 8192)
TCP: reno registered
UDP hash table entries: 512 (order: 2, 16384 bytes)
UDP-Lite hash table entries: 512 (order: 2, 16384 bytes)
NET: Registered protocol family 1
futex hash table entries: 1024 (order: 4, 65536 bytes)
msgmni has been set to 1470
bounce: pool size: 64 pages
Block layer SCSI generic (bsg) driver version 0.4 loaded (major 249)
io scheduler noop registered
io scheduler deadline registered (default)
dma-pl330 ffb20000.dma-controller: Loaded driver for PL330 DMAC-2364208
dma-pl330 ffb20000.dma-controller: 	DBUFF-64x8bytes Num_Chans-5 Num_Peri-6 Num_Events-10
dma-pl330 ff250000.dma-controller: Loaded driver for PL330 DMAC-2364208
dma-pl330 ff250000.dma-controller: 	DBUFF-128x8bytes Num_Chans-8 Num_Peri-20 Num_Events-16
Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
ff180000.serial: ttyS0 at MMIO 0xff180000 (irq = 87, base_baud = 1500000) is a 16550A
ff190000.serial: ttyS1 at MMIO 0xff190000 (irq = 88, base_baud = 1500000) is a 16550A
console [ttyS2] disabled
ff690000.serial: ttyS2 at MMIO 0xff690000 (irq = 89, base_baud = 1500000) is a 16550A
console [ttyS2] enabled
console [ttyS2] enabled
bootconsole [earlycon0] disabled
bootconsole [earlycon0] disabled
ff1b0000.serial: ttyS3 at MMIO 0xff1b0000 (irq = 90, base_baud = 1500000) is a 16550A
dw-apb-uart: probe of ff1c0000.serial failed with error -28
[drm] Initialized drm 1.1.0 20060810
brd: module loaded
stmmaceth ff290000.ethernet: no regulator found
ERROR: could not get clock /ethernet@ff290000:stmmaceth(0)
stmmaceth ff290000.ethernet: stmmac_dvr_probe: warning: cannot get CSR clock
stmmac_pltfr_probe: main driver probe failed
stmmaceth: probe of ff290000.ethernet failed with error -2
s3c-hsotg ff540000.usb: no platform data or transceiver defined
platform ff540000.usb: Driver s3c-hsotg requests probe deferral
dwc2 ff540000.usb: DWC OTG Controller
dwc2 ff540000.usb: new USB bus registered, assigned bus number 1
dwc2 ff540000.usb: irq 57, io mem 0x00000000
usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb1: Product: DWC OTG Controller
usb usb1: Manufacturer: Linux 3.17.0-rc1+ dwc2_hsotg
usb usb1: SerialNumber: ff540000.usb
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 1 port detected
mousedev: PS/2 mouse device common for all mice
rk3x-i2c ff650000.i2c: using default SCL frequency: 100000
VDD_CPU: 850 <--> 1350 mV at 1000 mV
VDD_CPU: supplied by sys-supply
VDD_GPU: 850 <--> 1350 mV at 1000 mV
VDD_GPU: supplied by sys-supply
rtc-hym8563 0-0051: no valid clock/calendar values available
rtc-hym8563 0-0051: rtc core: registered hym8563 as rtc0
VCC_DDR: 1200 mV
VCC_IO: 3300 mV
VDD_LOG: 1000 mV
VCC_20: 2000 mV
VCCIO_SD: 3300 mV
VDD10_LCD: 1000 mV
VCCA_18: at 3300 mV
VCCA_33: 3300 mV
VCC_LAN: 3300 mV
VDD_10: 1000 mV
VCC_18: 1800 mV
VCC18_LCD: 1800 mV
rk3x-i2c ff650000.i2c: Initialized RK3xxx I2C bus at f00b2000
softdog: Software Watchdog Timer: 0.08 initialized. soft_noboot=0 soft_margin=60 sec soft_panic=0 (nowayout=0)
Synopsys Designware Multimedia Card Interface Driver
platform ff0c0000.dwmmc: Driver dw_mmc requests probe deferral
usbcore: registered new interface driver usbhid
usbhid: USB HID core driver
usbcore: registered new interface driver r8188eu
usbcore: registered new interface driver rtl8723au
ff100000.saradc supply vref not found, using dummy regulator
TCP: cubic registered
NET: Registered protocol family 17
Registering SWP/SWPB emulation handler
sdmmc-supply: 3300 mV
sdmmc-supply: supplied by VCC_IO
dw_mmc ff0c0000.dwmmc: Using PIO mode.
dw_mmc ff0c0000.dwmmc: Version ID is 270a
dw_mmc ff0c0000.dwmmc: DW MMC controller at irq 64, 32 bit host data width, 256 deep fifo
mmc_host mmc0: Bus speed (slot 0) = 400000Hz (slot req 400000Hz, actual 400000HZ div = 0)
dw_mmc ff0c0000.dwmmc: 1 slots initialized
input: gpio-keys as /devices/gpio-keys/input/input0
rtc-hym8563 0-0051: no valid clock/calendar values available
rtc-hym8563 0-0051: hctosys: unable to read the hardware clock
Freeing unused kernel memory: 2056K (c0575000 - c0777000)
mknod: /dev/null: File exists
mount: mounting /dev/mmcblk0p1 on /mnt failed: No such device or address
total 0
drwxr-xr-x    2 1000     1000             0 Nov  4  2013 .
drwxr-xr-x   13 1000     1000             0 Nov  4  2013 ..
umount: can't umount /mnt: Invalid argument
processusb 1-1: new high-speed USB device number 2 using dwc2
or	: 0
model name	: ARMv7 Processor rev 1 (v7l)
Features	: half thumb fastmult vfp edsp neon vfpv3 tls vfpv4 idiva idivt vfpd32 lpae evtstrm
CPU implementer	: 0x41
CPU architecture: 7
CPU variant	: 0x0
CPU part	: 0xc0d
CPU revision	: 1

Hardware	: Rockchip Cortex-A9 (Device Tree)
Revision	: 0000
Serial		: 0000000000000000
           CPU0
 27:        180       GIC  27  arch_timer
 32:          0       GIC  32  ffb20000.dma-controller
 33:          0       GIC  33  ffb20000.dma-controller
 34:          0       GIC  34  ff250000.dma-controller
 35:          0       GIC  35  ff250000.dma-controller
 57:          2       GIC  57  ff540000.usb, dwc2_hsotg:usb1
 64:          0       GIC  64  dw-mci
 68:          0       GIC  68  ff100000.saradc
 89:          3       GIC  89  serial
 92:        180       GIC  92  ff650000.i2c
192:          0  rockchip_gpio_irq   4  hym8563
193:          0  rockchip_gpio_irq   5  GPIO Key Power
IPI0:          0  CPU wakeup interrupts
IPI1:          0  Timer broadcast interrupts
IPI2:          0  Rescheduling interrupts
IPI3:          0  Function call interrupts
IPI4:          0  Single function call interrupts
IPI5:          0  CPU stop interrupts
IPI6:          0  IRQ work interrupts
IPI7:          0  completion interrupts
Err:          0


BusyBox v1.20.2 (Debian 1:1.20.0-8) built-in shell (ash)
Enter 'help' for a list of built-in commands.

/bin/sh: can't access tty; job control turned off