API tools faq
paste
Advertisement
armoon

u-boot-n2 emmc failed

armoon
Dec 20th, 2019
148
0
Never
Add comment
Not a member of Pastebin yet? Sign Up, it unlocks many cool features!
text 7.27 KB | None | 0 0
raw download clone embed print report
  1. => reset
  2. resetting ...
  3. bl31 reboot reason: 0xd
  4. bl31 reboot reason: 0x0
  5. system cmd 1.
  6. G12B:BL:6e7c85:7898ac;FEAT:E0F83180:2000;POC:F;RCY:0;EMMC:0;READ:0;0.0
  7. bl2_stage_init 0x01
  8. bl2_stage_init 0x81
  9. hw id: 0x0000 - pwm id 0x01
  10. bl2_stage_init 0xc1
  11. bl2_stage_init 0x02
  12.  
  13. L0:00000000
  14. L1:00000703
  15. L2:00008067
  16. L3:04000000
  17. B2:00002000
  18. B1:e0f83180
  19.  
  20. TE: 113141
  21.  
  22. BL2 Built : 06:17:13, Jun 28 2019. g12b gf0505d7-dirty - qi.duan@droid13
  23.  
  24. Board ID = 4
  25. Set A53 clk to 24M
  26. Set A73 clk to 24M
  27. Set clk81 to 24M
  28. A53 clk: 1200 MHz
  29. A73 clk: 1200 MHz
  30. CLK81: 166.6M
  31. smccc: 0002022b
  32. eMMC boot @ 0
  33. sw8 s
  34. DDR driver_vesion: LPDDR4_PHY_V_0_1_14 build time: Jun 28 2019 06:17:09
  35. board id: 4
  36. Load FIP HDR from eMMC, src: 0x00010200, des: 0xfffd0000, size: 0x00004000, part: 0
  37. fw parse done
  38. Load ddrfw from eMMC, src: 0x00060200, des: 0xfffd0000, size: 0x0000c000, part: 0
  39. Load ddrfw from eMMC, src: 0x00038200, des: 0xfffd0000, size: 0x00004000, part: 0
  40. PIEI prepare done
  41. fastboot data load
  42. 00000000
  43. emmc switch 1 ok
  44. 00000000
  45. emmc switch 2 ok
  46. fastboot data verify
  47. verify result: 255
  48. Cfg max: 1, cur: 1. Board id: 255. Force loop cfg
  49. DDR4 probe
  50. ddr clk to 1320MHz
  51. Load ddrfw from eMMC, src: 0x00014200, des: 0xfffd0000, size: 0x0000c000, part: 0
  52. 00000000
  53. emmc switch 0 ok
  54. Check phy result
  55. INFO : End of initialization
  56. INFO : End of read enable training
  57. INFO : End of fine write leveling
  58. INFO : End of read dq deskew training
  59. INFO : End of MPR read delay center optimization
  60. INFO : End of Write leveling coarse delay
  61. INFO : End of write delay center optimization
  62. INFO : End of read delay center optimization
  63. INFO : End of max read latency training
  64. INFO : Training has run successfully!
  65. 1D training succeed
  66. Load ddrfw from eMMC, src: 0x00020200, des: 0xfffd0000, size: 0x0000c000, part: 0
  67. Check phy result
  68. INFO : End of initialization
  69. INFO : End of 2D read delay Voltage center optimization
  70. INFO : End of 2D write delay Voltage center optimization
  71. INFO : Training has run successfully!
  72.  
  73. R0_RxClkDly_Margin==82 ps 7
  74. R0_TxDqDly_Margi==94 ps 8
  75.  
  76.  
  77. R1_RxClkDly_Margin==0 ps 0
  78. R1_TxDqDly_Margi==0 ps 0
  79.  
  80. dwc_ddrphy_apb_wr((0<<20)|(2<<16)|(0<<12)|(0xb0):0001
  81. 2D training succeed
  82. auto size-- 65535DDR cs0 size: 2048MB
  83. DDR cs1 size: 2048MB
  84. DMC_DDR_CTRL: 00600024DDR size: 3928MB
  85. cs0 DataBus test pass
  86. cs1 DataBus test pass
  87. cs0 AddrBus test pass
  88. cs1 AddrBus test pass
  89. pre test bdlr_100_average==430 bdlr_100_min==430 bdlr_100_max==430 bdlr_100_cur==430
  90. aft test bdlr_100_average==430 bdlr_100_min==430 bdlr_100_max==430 bdlr_100_cur==430
  91. non-sec scramble use zero key
  92. ddr scramble enabled
  93.  
  94. 100bdlr_step_size ps== 440
  95. result report
  96. boot times 3Enable ddr reg access
  97. 00000000
  98. emmc switch 3 ok
  99. Authentication key not yet programmed
  100. get rpmb counter error 0x00000007
  101. 00000000
  102. emmc switch 0 ok
  103. Load FIP HDR from eMMC, src: 0x00010200, des: 0x01700000, size: 0x00004000, part: 0
  104. Load BL3X from eMMC, src: 0x0006c200, des: 0x0175c000, size: 0x00088200, part: 0
  105. 0.0;M3 CHK:0;cm4_sp_mode 0
  106. E30HDR
  107. MVN_1=0x00000000
  108. MVN_2=0x00000000
  109. [Image: g12b_v1.1.3375-8f9c8a7 2019-01-24 10:44:46 guotai.shen@droid11-sz]
  110. OPS=0x40
  111. ring efuse init
  112. chipver efuse init
  113. 29 0a 40 00 01 20 10 00 00 15 30 32 54 52 4d 50
  114. [3.472524 Inits done]
  115. secure task start!
  116. high task start!
  117. low task start!
  118. run into bl31
  119. NOTICE: BL31: v1.3(release):ab8811b
  120. NOTICE: BL31: Built : 15:03:31, Feb 12 2019
  121. NOTICE: BL31: G12A normal boot!
  122. NOTICE: BL31: BL33 decompress pass
  123. ERROR: Error initializing runtime service opteed_fast
  124.  
  125.  
  126. U-Boot 2020.01-rc5-00009-g269c6e8c39 (Dec 20 2019 - 15:38:58 +0530) odroid-n2
  127.  
  128. Model: Hardkernel ODROID-N2
  129. SoC: Amlogic Meson G12B (S922X) Revision 29:a (40:2)
  130. DRAM: 3.8 GiB
  131. MMC: sd@ffe05000: 0, mmc@ffe07000: 1
  132. In: serial@3000
  133. Out: serial@3000
  134. Err: serial@3000
  135. Net:
  136. Warning: ethernet@ff3f0000 (eth0) using random MAC address - ba:97:fc:8e:c0:7a
  137. eth0: ethernet@ff3f0000
  138. Hit any key to stop autoboot: 0
  139. Card did not respond to voltage select!
  140. unable to select a mode
  141. switch to partitions #0, OK
  142. mmc1(part 0) is current device
  143. ** No partition table - mmc 1 **
  144. MMC Device 2 not found
  145. no mmc device at slot 2
  146. starting USB...
  147. Bus usb@ff500000: Register 3000140 NbrPorts 3
  148. Starting the controller
  149. USB XHCI 1.10
  150. scanning bus usb@ff500000 for devices... 1 USB Device(s) found
  151. scanning usb for storage devices... 0 Storage Device(s) found
  152.  
  153. Device 0: unknown device
  154. Speed: 1000, full duplex
  155. BOOTP broadcast 1
  156. BOOTP broadcast 2
  157. BOOTP broadcast 3
  158. BOOTP broadcast 4
  159. BOOTP broadcast 5
  160. BOOTP broadcast 6
  161. BOOTP broadcast 7
  162. BOOTP broadcast 8
  163. BOOTP broadcast 9
  164. BOOTP broadcast 10
  165. BOOTP broadcast 11
  166. BOOTP broadcast 12
  167. BOOTP broadcast 13
  168. BOOTP broadcast 14
  169. BOOTP broadcast 15
  170. BOOTP broadcast 16
  171. BOOTP broadcast 17
  172.  
  173. Retry time exceeded; starting again
  174. missing environment variable: pxeuuid
  175. missing environment variable: bootfile
  176. Retrieving file: pxelinux.cfg/00000000
  177. Speed: 1000, full duplex
  178. *** ERROR: `serverip' not set
  179. missing environment variable: bootfile
  180. Retrieving file: pxelinux.cfg/0000000
  181. Speed: 1000, full duplex
  182. *** ERROR: `serverip' not set
  183. missing environment variable: bootfile
  184. Retrieving file: pxelinux.cfg/000000
  185. Speed: 1000, full duplex
  186. *** ERROR: `serverip' not set
  187. missing environment variable: bootfile
  188. Retrieving file: pxelinux.cfg/00000
  189. Speed: 1000, full duplex
  190. *** ERROR: `serverip' not set
  191. missing environment variable: bootfile
  192. Retrieving file: pxelinux.cfg/0000
  193. Speed: 1000, full duplex
  194. *** ERROR: `serverip' not set
  195. missing environment variable: bootfile
  196. Retrieving file: pxelinux.cfg/000
  197. Speed: 1000, full duplex
  198. *** ERROR: `serverip' not set
  199. missing environment variable: bootfile
  200. Retrieving file: pxelinux.cfg/00
  201. Speed: 1000, full duplex
  202. *** ERROR: `serverip' not set
  203. missing environment variable: bootfile
  204. Retrieving file: pxelinux.cfg/0
  205. Speed: 1000, full duplex
  206. *** ERROR: `serverip' not set
  207. missing environment variable: bootfile
  208. Retrieving file: pxelinux.cfg/default-arm-meson-w400
  209. Speed: 1000, full duplex
  210. *** ERROR: `serverip' not set
  211. missing environment variable: bootfile
  212. Retrieving file: pxelinux.cfg/default-arm-meson
  213. Speed: 1000, full duplex
  214. *** ERROR: `serverip' not set
  215. missing environment variable: bootfile
  216. Retrieving file: pxelinux.cfg/default-arm
  217. Speed: 1000, full duplex
  218. *** ERROR: `serverip' not set
  219. missing environment variable: bootfile
  220. Retrieving file: pxelinux.cfg/default
  221. Speed: 1000, full duplex
  222. *** ERROR: `serverip' not set
  223. Config file not found
  224. Speed: 1000, full duplex
  225. BOOTP broadcast 1
  226. BOOTP broadcast 2
  227. BOOTP broadcast 3
  228. BOOTP broadcast 4
  229. BOOTP broadcast 5
  230. BOOTP broadcast 6
  231. BOOTP broadcast 7
  232. BOOTP broadcast 8
  233. BOOTP broadcast 9
  234. BOOTP broadcast 10
  235. BOOTP broadcast 11
  236. BOOTP broadcast 12
  237. BOOTP broadcast 13
  238. BOOTP broadcast 14
  239. BOOTP broadcast 15
  240. BOOTP broadcast 16
  241. BOOTP broadcast 17
  242.  
  243. Retry time exceeded; starting again
  244. Speed: 1000, full duplex
  245. BOOTP broadcast 1
  246. BOOTP broadcast 2
  247. BOOTP broadcast 3
  248. BOOTP broadcast 4
  249. BOOTP broadcast 5
  250. BOOTP broadcast 6
  251. BOOTP broadcast 7
  252. BOOTP broadcast 8
  253. BOOTP broadcast 9
  254. BOOTP broadcast 10
  255. BOOTP broadcast 11
  256. BOOTP broadcast 12
  257. BOOTP broadcast 13
  258. BOOTP broadcast 14
  259. BOOTP broadcast 15
  260. BOOTP broadcast 16
  261. BOOTP broadcast 17
  262.  
  263. Retry time exceeded; starting again
  264. =>
Advertisement
Add Comment
Please, Sign In to add comment
Advertisement
Public Pastes
Advertisement
We use cookies for various purposes including analytics. By continuing to use Pastebin, you agree to our use of cookies as described in the Cookies Policy.  OK, I Understand
Not a member of Pastebin yet?
Sign Up, it unlocks many cool features!