Advertisement
Not a member of Pastebin yet?
Sign Up,
it unlocks many cool features!
- __ __ _ _
- | \/ | __ _ _ ____ _____| | |
- | |\/| |/ _` | '__\ \ / / _ \ | |
- | | | | (_| | | \ V / __/ | |
- |_| |_|\__,_|_| \_/ \___|_|_|
- _ _ ____ _
- | | | | | __ ) ___ ___ | |_
- | | | |___| _ \ / _ \ / _ \| __|
- | |_| |___| |_) | (_) | (_) | |_
- \___/ |____/ \___/ \___/ \__|
- ** MARVELL BOARD: SHEEVA PLUG LE
- U-Boot 1.1.4 (Jul 14 2009 - 06:46:57) Marvell version: 3.4.16
- U-Boot code: 00600000 -> 0067FFF0 BSS: -> 006CF120
- Soc: MV88F6281 Rev 3 (DDR2)
- CPU running @ 1200Mhz L2 running @ 400Mhz
- SysClock = 400Mhz , TClock = 200Mhz
- DRAM CAS Latency = 5 tRP = 5 tRAS = 18 tRCD=6
- DRAM CS[0] base 0x00000000 size 256MB
- DRAM CS[1] base 0x10000000 size 256MB
- DRAM Total size 512MB 16bit width
- Flash: 0 kB
- Addresses 8M - 0M are saved for the U-Boot usage.
- Mem malloc Initialization (8M - 7M): Done
- NAND:512 MB
- CPU : Marvell Feroceon (Rev 1)
- Streaming disabled
- Write allocate disabled
- USB 0: host mode
- PEX 0: interface detected no Link.
- Net: egiga0 [PRIME], egiga1
- Hit any key to stop autoboot: 0
- NAND read: device 0 offset 0x100000, size 0x400000
- Reading data from 0x4ff800 -- 100% complete.
- 4194304 bytes read: OK
- ## Booting image at 00800000 ...
- Image Name: Linux-2.6.22.18
- Created: 2009-03-19 9:18:16 UTC
- Image Type: ARM Linux Kernel Image (uncompressed)
- Data Size: 2106696 Bytes = 2 MB
- Load Address: 00008000
- Entry Point: 00008000
- Verifying Checksum ... OK
- OK
- Starting kernel ...
- Uncompressing Linux.................................................................................................................................... done, booting the kernel.
- Linux version 2.6.22.18 (dhaval@devbox) (gcc version 4.2.1) #1 Thu Mar 19 14:46:22 IST 2009
- CPU: ARM926EJ-S [56251311] revision 1 (ARMv5TE), cr=00053177
- Machine: Feroceon-KW
- Using UBoot passing parameters structure
- Memory policy: ECC disabled, Data cache writeback
- CPU0: D VIVT write-back cache
- CPU0: I cache: 16384 bytes, associativity 4, 32 byte lines, 128 sets
- CPU0: D cache: 16384 bytes, associativity 4, 32 byte lines, 128 sets
- Built 1 zonelists. Total pages: 130048
- Kernel command line: console=ttyS0,115200 mtdparts=nand_mtd:0x400000@0x100000(uImage),0x1fb00000@0x500000(rootfs) rw root=/dev/mtdblock1 rw
- PID hash table entries: 2048 (order: 11, 8192 bytes)
- Console: colour dummy device 80x30
- Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
- Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
- Memory: 256MB 256MB 0MB 0MB = 512MB total
- Memory: 515456KB available (3864K code, 257K data, 104K init)
- Mount-cache hash table entries: 512
- CPU: Testing write buffer coherency: ok
- NET: Registered protocol family 16
- CPU Interface
- -------------
- SDRAM_CS0 ....base 00000000, size 256MB
- SDRAM_CS1 ....base 10000000, size 256MB
- SDRAM_CS2 ....disable
- SDRAM_CS3 ....disable
- PEX0_MEM ....base e8000000, size 128MB
- PEX0_IO ....base f2000000, size 1MB
- INTER_REGS ....base f1000000, size 1MB
- NFLASH_CS ....base fa000000, size 2MB
- SPI_CS ....base f4000000, size 16MB
- BOOT_ROM_CS ....no such
- DEV_BOOTCS ....no such
- CRYPT_ENG ....base f0000000, size 2MB
- Marvell Development Board (LSP Version KW_LSP_4.2.7_patch2)-- SHEEVA PLUG Soc: MV88F6281 Rev 3 LE
- Detected Tclk 200000000 and SysClk 400000000
- MV Buttons Device Load
- Marvell USB EHCI Host controller #0: c08b8600
- PEX0 interface detected no Link.
- PCI: bus0: Fast back to back transfers enabled
- SCSI subsystem initialized
- usbcore: registered new interface driver usbfs
- usbcore: registered new interface driver hub
- usbcore: registered new device driver usb
- NET: Registered protocol family 2
- Time: kw_clocksource clocksource has been installed.
- IP route cache hash table entries: 16384 (order: 4, 65536 bytes)
- TCP established hash table entries: 65536 (order: 7, 524288 bytes)
- TCP bind hash table entries: 65536 (order: 6, 262144 bytes)
- TCP: Hash tables configured (established 65536 bind 65536)
- TCP reno registered
- RTC registered
- Use the XOR engines (acceleration) for enhancing the following functions:
- o RAID 5 Xor calculation
- o kernel memcpy
- o kenrel memzero
- Number of XOR engines to use: 4
- cesadev_init(c000c894)
- mvCesaInit: sessions=640, queue=64, pSram=f0000000
- Warning: TS unit is powered off.
- MV Buttons Driver Load
- NTFS driver 2.1.28 [Flags: R/O].
- JFFS2 version 2.2. (NAND) © 2001-2006 Red Hat, Inc.
- io scheduler noop registered
- io scheduler anticipatory registered (default)
- Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing disabled
- serial8250.0: ttyS0 at MMIO 0xf1012000 (irq = 33) is a 16550A
- serial8250.0: ttyS1 at MMIO 0xf1012100 (irq = 34) is a 16550A
- Loading Marvell Ethernet Driver:
- o Cached descriptors in DRAM
- o DRAM SW cache-coherency
- o Single RX Queue support - ETH_DEF_RXQ=0
- o Single TX Queue support - ETH_DEF_TXQ=0
- o TCP segmentation offload enabled
- o Receive checksum offload enabled
- o Transmit checksum offload enabled
- o Network Fast Processing (Routing) supported
- o Driver ERROR statistics enabled
- o Driver INFO statistics enabled
- o Proc tool API enabled
- o Rx descripors: q0=128
- o Tx descripors: q0=532
- o Loading network interface(s):
- o eth0, ifindex = 1, GbE port = 0
- o eth1, ifindex = 2, GbE port = 1
- mvFpRuleDb (dfe70000): 16384 entries, 65536 bytes
- Intel(R) PRO/1000 Network Driver - version 7.3.20-k2-NAPI
- Copyright (c) 1999-2006 Intel Corporation.
- e100: Intel(R) PRO/100 Network Driver, 3.5.17-k4-NAPI
- e100: Copyright(c) 1999-2006 Intel Corporation
- Integrated Sata device found
- scsi0 : Marvell SCSI to SATA adapter
- scsi1 : Marvell SCSI to SATA adapter
- NFTL driver: nftlcore.c $Revision: 1.98 $, nftlmount.c $Revision: 1.41 $
- NAND device: Manufacturer ID: 0xec, Chip ID: 0xdc (Samsung NAND 512MiB 3,3V 8-bit)
- Scanning device for bad blocks
- 2 cmdlinepart partitions found on MTD device nand_mtd
- Using command line partition definition
- Creating 2 MTD partitions on "nand_mtd":
- 0x00100000-0x00500000 : "uImage"
- 0x00500000-0x20000000 : "rootfs"
- ehci_marvell ehci_marvell.70059: Marvell Orion EHCI
- ehci_marvell ehci_marvell.70059: new USB bus registered, assigned bus number 1
- ehci_marvell ehci_marvell.70059: irq 19, io base 0xf1050100
- ehci_marvell ehci_marvell.70059: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
- usb usb1: configuration #1 chosen from 1 choice
- hub 1-0:1.0: USB hub found
- hub 1-0:1.0: 1 port detected
- USB Universal Host Controller Interface driver v3.0
- usbcore: registered new interface driver usblp
- drivers/usb/class/usblp.c: v0.13: USB Printer Device Class driver
- Initializing USB Mass Storage driver...
- usbcore: registered new interface driver usb-storage
- USB Mass Storage support registered.
- mice: PS/2 mouse device common for all mice
- i2c /dev entries driver
- Linux telephony interface: v1.00
- Marvell Telephony Driver:
- mvBoardVoiceAssembleModeGet: TDM not supported(boardId=0x9)
- assembly=-1,irq=-1
- mp_check_config: Error, invalid voice assembley mode
- md: linear personality registered for level -1
- md: raid0 personality registered for level 0
- md: raid1 personality registered for level 1
- raid6: int32x1 97 MB/s
- raid6: int32x2 114 MB/s
- raid6: int32x4 122 MB/s
- raid6: int32x8 110 MB/s
- raid6: using algorithm int32x4 (122 MB/s)
- md: raid6 personality registered for level 6
- md: raid5 personality registered for level 5
- md: raid4 personality registered for level 4
- raid5: measuring checksumming speed
- arm4regs : 1084.000 MB/sec
- 8regs : 754.800 MB/sec
- 32regs : 899.600 MB/sec
- raid5: using function: arm4regs (1084.000 MB/sec)
- device-mapper: ioctl: 4.11.0-ioctl (2006-10-12) initialised: dm-devel@redhat.com
- dm_crypt using the OCF package.
- sdhci: Secure Digital Host Controller Interface driver
- sdhci: Copyright(c) Pierre Ossman
- mvsdmmc: irq =28 start f1090000
- mvsdmmc: no IRQ detect
- usbcore: registered new interface driver usbhid
- drivers/hid/usbhid/hid-core.c: v2.6:USB HID core driver
- Advanced Linux Sound Architecture Driver Version 1.0.14 (Thu May 31 09:03:25 2007 UTC).
- mvCLAudioCodecRegGet: Error while reading register!
- mvCLAudioCodecInit: Error - Invalid Cirrus Logic chip/rev ID!
- Error - Cannot initialize audio decoder.at address =0xff<6>ALSA device list:
- #0: Marvell mv88fx_snd ALSA driver
- TCP cubic registered
- NET: Registered protocol family 1
- NET: Registered protocol family 17
- md: Autodetecting RAID arrays.
- md: autorun ...
- md: ... autorun DONE.
- Empty flash at 0x130de0d4 ends at 0x130de800
- VFS: Mounted root (jffs2 filesystem).
- Freeing init memory: 104K
- INIT: version 2.88 booting
- udev requires a kernel >= 2.6.26, not started. ... failed!
- failed!
- Setting the system clock.
- Cannot access the Hardware Clock via any known method.
- Use the --debug option to see the details of our search for an access method.
- Unable to set System Clock to: Wed Mar 27 01:23:37 UTC 2013 ... (warning).
- Activating swap...done.
- Setting the system clock.
- Cannot access the Hardware Clock via any known method.
- Use the --debug option to see the details of our search for an access method.
- Unable to set System Clock to: Wed Mar 27 01:23:38 UTC 2013 ... (warning).
- Cleaning up ifupdown....
- Loading kernel modules...done.
- Activating lvm and md swap...done.
- Checking file systems...fsck from util-linux-ng 2.17.2
- done.
- Setting kernel variables ...done.
- Mounting local filesystems...done.
- Activating swapfile swap...done.
- Cleaning up temporary files.../lib/lsb/init-functions: line 191: /dev/null: cannot overwrite existing file
- .
- Setting up networking....
- Configuring network interfaces...Internet Systems Consortium DHCP Client V3.1.1
- Copyright 2004-2008 Internet Systems Consortium.
- All rights reserved.
- For info, please visit http://www.isc.org/sw/dhcp/
- eth0: link down
- eth0: started
- Listening on LPF/eth0/f0:ad:4e:01:d3:95
- Sending on LPF/eth0/f0:ad:4e:01:d3:95
- Sending on Socket/fallback
- eth0: link up, full duplex, speed 100 Mbps
- DHCPREQUEST on eth0 to 255.255.255.255 port 67
- DHCPACK from 192.168.2.1
- bound to 192.168.2.136 -- renewal in 41296 seconds.
- done.
- Cleaning up temporary files....
- locale: Cannot set LC_CTYPE to default locale: No such file or directory
- locale: Cannot set LC_MESSAGES to default locale: No such file or directory
- locale: Cannot set LC_ALL to default locale: No such file or directory
- Setting console screen modes and fonts.
- JFFS2 notice: (874) check_node_data: wrong data CRC in data node at 0x1f752800: read 0xbf7e936f, calculated 0x37e9c54a.
- cu: Got hangup signal
- Disconnected.
Advertisement
Add Comment
Please, Sign In to add comment
Advertisement