Advertisement
Not a member of Pastebin yet?
Sign Up,
it unlocks many cool features!
- CFE version 1.0.37-105.22-1 for BCM96368 (32bit,SP,BE)
- Build Date: Fri Mar 19 11:53:33 CST 2010 (jojopo@broadcom_v060.comtrend.com)
- Copyright (C) 2000-2009 Broadcom Corporation.
- Parallel flash device: name AM29DL800B, id 0x22cb size 8192KB
- Total Flash size: 8192K with 135 sectors
- Chip ID: BCM6368B2, MIPS: 400MHz
- Main Thread: TP0
- Total Memory: 67108864 bytes (64MB)
- Boot Address: 0xb8000000
- Board IP address : 192.168.1.1:ffffff00
- Host IP address : 192.168.1.100
- Gateway IP address :
- Run from flash/host (f/h) : f
- Default host run file name : vmlinux
- Default host flash file name : bcm963xx_fs_kernel
- Boot delay (0-9 seconds) : 1
- Board Id (0-14) : 96368M-1341N
- Number of MAC Addresses (1-32) : 11
- Base MAC Address : 64:68:0c:
- PSI Size (1-64) KBytes : 24
- Enable Backup PSI [0|1] : 0
- System Log Size (0-256) KBytes : 0
- Main Thread Number [0|1] : 0
- *** Press any key to stop auto run (1 seconds) ***
- Auto run second count down: 0
- Booting from only image (0xb8010000) ...
- Code Address: 0x80010000, Entry Address: 0x80010000
- LZMA: Prossible old LZMA format, trying to decompress..
- Decompression OK!
- Entry at 0x80010000
- Closing network.
- Disabling Switch ports.
- Flushing Receive Buffers...
- 0 buffers found.
- Closing DMA Channels.
- Starting program at 0x80010000
- [ 0.000000] Linux version 3.10.23 (taxodium@debian) (gcc version 4.6.4 (OpenWrt/Linaro GCC 4.6-2013.05 r39025) ) #6 SMP We3
- [ 0.000000] Detected Broadcom 0x6368 CPU revision b2
- [ 0.000000] CPU frequency is 400 MHz
- [ 0.000000] 64MB of RAM installed
- [ 0.000000] registering 38 GPIOs
- [ 0.000000] board_bcm963xx: Boot address 0xb8000000
- [ 0.000000] board_bcm963xx: CFE version: 1.0.37-105.22-1
- [ 0.000000] bootconsole [early0] enabled
- [ 0.000000] CPU revision is: 0002a031 (Broadcom BMIPS4350)
- [ 0.000000] board_bcm963xx: board name: 96368M-1341N
- [ 0.000000] Determined physical RAM map:
- [ 0.000000] memory: 04000000 @ 00000000 (usable)
- [ 0.000000] Initrd not found or empty - disabling initrd
- [ 0.000000] Zone ranges:
- [ 0.000000] Normal [mem 0x00000000-0x03ffffff]
- [ 0.000000] Movable zone start for each node
- [ 0.000000] Early memory node ranges
- [ 0.000000] node 0: [mem 0x00000000-0x03ffffff]
- [ 0.000000] On node 0 totalpages: 16384
- [ 0.000000] free_area_init_node: node 0, pgdat 80301a20, node_mem_map 81000000
- [ 0.000000] Normal zone: 128 pages used for memmap
- [ 0.000000] Normal zone: 0 pages reserved
- [ 0.000000] Normal zone: 16384 pages, LIFO batch:3
- [ 0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 16 bytes.
- [ 0.000000] Primary data cache 32kB, 2-way, VIPT, cache aliases, linesize 16 bytes
- [ 0.000000] PERCPU: Embedded 7 pages/cpu @81083000 s6624 r8192 d13856 u32768
- [ 0.000000] pcpu-alloc: s6624 r8192 d13856 u32768 alloc=8*4096
- [ 0.000000] pcpu-alloc: [0] 0 [0] 1
- [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 16256
- [ 0.000000] Kernel command line: root=/dev/mtdblock2 rootfstype=squashfs,jffs2 noinitrd console=ttyS0,115200 debug
- [ 0.000000] PID hash table entries: 256 (order: -2, 1024 bytes)
- [ 0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
- [ 0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
- [ 0.000000] Memory: 61332k/65536k available (2541k kernel code, 4204k reserved, 546k data, 176k init, 0k highmem)
- [ 0.000000] Hierarchical RCU implementation.
- [ 0.000000] NR_IRQS:128
- [ 0.000000] Calibrating delay loop... 397.82 BogoMIPS (lpj=795648)
- [ 0.032000] pid_max: default: 32768 minimum: 301
- [ 0.036000] Mount-cache hash table entries: 512
- [ 0.044000] SMP: Booting CPU1...
- [ 0.048000] CPU revision is: 0002a031 (Broadcom BMIPS4350)
- [ 0.048000] Primary instruction cache 64kB, VIPT, 4-way, linesize 16 bytes.
- [ 0.048000] Primary data cache 32kB, 2-way, VIPT, cache aliases, linesize 16 bytes
- [ 0.076000] SMP: CPU1 is running
- [ 0.076000] Brought up 2 CPUs
- [ 0.100000] device: 'platform': device_add
- [ 0.104000] bus: 'platform': registered
- [ 0.108000] bus: 'cpu': registered
- [ 0.108000] device: 'cpu': device_add
- [ 0.120000] bus: 'workqueue': registered
- [ 0.124000] device: 'workqueue': device_add
- [ 0.128000] NET: Registered protocol family 16
- [ 0.132000] device class 'bdi': registering
- [ 0.136000] device class 'gpio': registering
- [ 0.140000] device: 'gpiochip0': device_add
- [ 0.144000] device class 'pci_bus': registering
- [ 0.148000] bus: 'pci': registered
- [ 0.152000] device class 'tty': registering
- [ 0.156000] bus: 'spi': registered
- [ 0.160000] device class 'spi_master': registering
- [ 0.164000] Registering platform device 'bcm63xx_uart.0'. Parent at platform
- [ 0.168000] device: 'bcm63xx_uart.0': device_add
- [ 0.172000] bus: 'platform': add device bcm63xx_uart.0
- [ 0.176000] Registering platform device 'bcm63xx_enet_shared.0'. Parent at platform
- [ 0.180000] device: 'bcm63xx_enet_shared.0': device_add
- [ 0.184000] bus: 'platform': add device bcm63xx_enet_shared.0
- [ 0.188000] Registering platform device 'bcm63xx_enetsw.0'. Parent at platform
- [ 0.192000] device: 'bcm63xx_enetsw.0': device_add
- [ 0.196000] bus: 'platform': add device bcm63xx_enetsw.0
- [ 0.200000] Registering platform device 'ehci-platform'. Parent at platform
- [ 0.204000] device: 'ehci-platform': device_add
- [ 0.208000] bus: 'platform': add device ehci-platform
- [ 0.212000] Registering platform device 'ohci-platform'. Parent at platform
- [ 0.216000] device: 'ohci-platform': device_add
- [ 0.220000] bus: 'platform': add device ohci-platform
- [ 0.224000] Registering platform device 'bcm63xx-spi'. Parent at platform
- [ 0.228000] device: 'bcm63xx-spi': device_add
- [ 0.232000] bus: 'platform': add device bcm63xx-spi
- [ 0.236000] Registering platform device 'physmap-flash.0'. Parent at platform
- [ 0.240000] device: 'physmap-flash.0': device_add
- [ 0.244000] bus: 'platform': add device physmap-flash.0
- [ 0.248000] Registering platform device 'leds-gpio.0'. Parent at platform
- [ 0.252000] device: 'leds-gpio.0': device_add
- [ 0.256000] bus: 'platform': add device leds-gpio.0
- [ 0.260000] Registering platform device 'gpio-keys-polled.0'. Parent at platform
- [ 0.264000] device: 'gpio-keys-polled.0': device_add
- [ 0.268000] bus: 'platform': add device gpio-keys-polled.0
- [ 0.272000] Registering platform device 'bcm63xx-rng'. Parent at platform
- [ 0.276000] device: 'bcm63xx-rng': device_add
- [ 0.280000] bus: 'platform': add device bcm63xx-rng
- [ 0.284000] Registering platform device 'bcm63xx-wdt'. Parent at platform
- [ 0.288000] device: 'bcm63xx-wdt': device_add
- [ 0.292000] bus: 'platform': add device bcm63xx-wdt
- [ 0.296000] registering PCI controller with io_map_base unset
- [ 0.300000] device: 'cpu0': device_add
- [ 0.300000] bus: 'cpu': add device cpu0
- [ 0.304000] device: 'cpu1': device_add
- [ 0.308000] bus: 'cpu': add device cpu1
- [ 0.320000] device: 'writeback': device_add
- [ 0.324000] bus: 'workqueue': add device writeback
- [ 0.332000] device: 'default': device_add
- [ 0.336000] bio: create slab <bio-0> at 0
- [ 0.340000] device class 'block': registering
- [ 0.344000] device class 'misc': registering
- [ 0.348000] device class 'mdio_bus': registering
- [ 0.352000] bus: 'mdio_bus': registered
- [ 0.356000] bus: 'mdio_bus': add driver Generic PHY
- [ 0.360000] bus: 'mmc': registered
- [ 0.364000] device class 'mmc_host': registering
- [ 0.368000] bus: 'sdio': registered
- [ 0.372000] device class 'leds': registering
- [ 0.376000] device: 'pci0000:00': device_add
- [ 0.380000] device: '0000:00': device_add
- [ 0.384000] PCI host bridge to bus 0000:00
- [ 0.388000] pci_bus 0000:00: root bus resource [mem 0x30000000-0x37ffffff]
- [ 0.392000] pci_bus 0000:00: root bus resource [io 0x8000000-0x800ffff]
- [ 0.396000] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff]
- [ 0.400000] pci 0000:00:01.0: [168c:0029] type 00 class 0x028000
- [ 0.404000] pci 0000:00:01.0: reg 10: [mem 0x00000000-0x0000ffff]
- [ 0.420000] pci 0000:00:01.0: PME# supported from D0 D3hot
- [ 0.424000] device: '0000:00:01.0': device_add
- [ 0.428000] bus: 'pci': add device 0000:00:01.0
- [ 0.432000] pci_bus 0000:00: busn_res: [bus 00-ff] end is updated to 00
- [ 0.436000] pci 0000:00:01.0: BAR 0: assigned [mem 0x30000000-0x3000ffff]
- [ 0.440000] device class 'net': registering
- [ 0.444000] device: 'lo': device_add
- [ 0.448000] Switching to clocksource MIPS
- [ 0.452000] device class 'mem': registering
- [ 0.456000] device: 'mem': device_add
- [ 0.460000] device: 'null': device_add
- [ 0.464000] device: 'port': device_add
- [ 0.468000] device: 'zero': device_add
- [ 0.472000] device: 'full': device_add
- [ 0.476000] device: 'random': device_add
- [ 0.480000] device: 'urandom': device_add
- [ 0.484000] device: 'kmsg': device_add
- [ 0.488000] device: 'tty': device_add
- [ 0.496000] device: 'console': device_add
- [ 0.500000] device class 'firmware': registering
- [ 0.504000] bus: 'ssb': registered
- [ 0.508000] bus: 'pci': add driver b43-pci-bridge
- [ 0.512000] NET: Registered protocol family 2
- [ 0.520000] TCP established hash table entries: 512 (order: 0, 4096 bytes)
- [ 0.524000] TCP bind hash table entries: 512 (order: 0, 4096 bytes)
- [ 0.532000] TCP: Hash tables configured (established 512 bind 512)
- [ 0.540000] TCP: reno registered
- [ 0.540000] UDP hash table entries: 256 (order: 1, 8192 bytes)
- [ 0.548000] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
- [ 0.556000] NET: Registered protocol family 1
- [ 0.560000] PCI: CLS 0 bytes, default 16
- [ 0.564000] bus: 'clocksource': registered
- [ 0.568000] device: 'clocksource': device_add
- [ 0.572000] device: 'clocksource0': device_add
- [ 0.580000] bus: 'clocksource': add device clocksource0
- [ 0.584000] bus: 'platform': add driver alarmtimer
- [ 0.588000] Registering platform device 'alarmtimer'. Parent at platform
- [ 0.596000] device: 'alarmtimer': device_add
- [ 0.600000] bus: 'platform': add device alarmtimer
- [ 0.604000] bus: 'platform': driver_probe_device: matched device alarmtimer with driver alarmtimer
- [ 0.616000] bus: 'platform': really_probe: probing driver alarmtimer with device alarmtimer
- [ 0.624000] driver: 'alarmtimer': driver_bound: bound to device 'alarmtimer'
- [ 0.632000] bus: 'platform': really_probe: bound device alarmtimer to driver alarmtimer
- [ 0.640000] audit: initializing netlink socket (disabled)
- [ 0.644000] type=2000 audit(0.644:1): initialized
- [ 0.652000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
- [ 0.656000] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
- [ 0.668000] msgmni has been set to 119
- [ 0.672000] io scheduler noop registered
- [ 0.676000] io scheduler deadline registered (default)
- [ 0.760000] crc32: CRC_LE_BITS = 1, CRC_BE BITS = 1
- [ 0.764000] crc32: self tests passed, processed 225944 bytes in 38985520 nsec
- [ 0.820000] crc32c: CRC_LE_BITS = 1
- [ 0.824000] crc32c: self tests passed, processed 225944 bytes in 23652105 nsec
- [ 0.832000] device: 'ptmx': device_add
- [ 0.836000] bus: 'platform': add driver bcm63xx_uart
- [ 0.840000] bus: 'platform': driver_probe_device: matched device bcm63xx_uart.0 with driver bcm63xx_uart
- [ 0.848000] bus: 'platform': really_probe: probing driver bcm63xx_uart with device bcm63xx_uart.0
- �[ 0.868000] console [ttyS0] enabled, bootconsole disabled= 10) is a bcm63xx_uart
- [ 0.868000] console [ttyS0] enabled, bootconsole disabled
- [ 0.876000] device: 'ttyS0': device_add
- [ 0.884000] driver: 'bcm63xx_uart.0': driver_bound: bound to device 'bcm63xx_uart'
- [ 0.892000] bus: 'platform': really_probe: bound device bcm63xx_uart.0 to driver bcm63xx_uart
- [ 0.900000] bus: 'platform': add driver bcm63xx-rng
- [ 0.904000] bus: 'platform': driver_probe_device: matched device bcm63xx-rng with driver bcm63xx-rng
- [ 0.912000] bus: 'platform': really_probe: probing driver bcm63xx-rng with device bcm63xx-rng
- [ 0.924000] device: 'hw_random': device_add
- [ 0.928000] bcm63xx-rng bcm63xx-rng: registered RNG driver
- [ 0.932000] driver: 'bcm63xx-rng': driver_bound: bound to device 'bcm63xx-rng'
- [ 0.940000] bus: 'platform': really_probe: bound device bcm63xx-rng to driver bcm63xx-rng
- [ 0.948000] device class 'mtd': registering
- [ 0.956000] device: 'mtd-unmap': device_add
- [ 0.960000] device: 'mtd-romap': device_add
- [ 0.964000] device: 'mtd-rwmap': device_add
- [ 0.968000] bus: 'platform': add driver physmap-flash
- [ 0.972000] bus: 'platform': driver_probe_device: matched device physmap-flash.0 with driver physmap-flash
- [ 0.984000] bus: 'platform': really_probe: probing driver physmap-flash with device physmap-flash.0
- [ 0.992000] physmap platform flash device: 08000000 at 18000000
- [ 1.000000] physmap-flash.0: Found 1 x16 devices at 0x0 in 16-bit bank. Manufacturer ID 0x0000c2 Chip ID 0x0022cb
- [ 1.012000] physmap-flash.0: Found an alias at 0x800000 for the chip at 0x0
- [ 1.016000] physmap-flash.0: Found an alias at 0x1000000 for the chip at 0x0
- [ 1.024000] physmap-flash.0: Found an alias at 0x1800000 for the chip at 0x0
- [ 1.032000] Amd/Fujitsu Extended Query Table at 0x0040
- [ 1.036000] Amd/Fujitsu Extended Query version 1.1.
- [ 1.044000] number of CFI chips: 1
- [ 1.048000] bcm63xxpart: CFE boot tag found with version 6 and board type 96368M-1341N
- [ 1.056000] bcm63xxpart: Partition 0 is CFE offset 0 and length 10000
- [ 1.060000] bcm63xxpart: Partition 1 is kernel offset 10100 and length 11ff00
- [ 1.068000] bcm63xxpart: Partition 2 is rootfs offset 130000 and length 6c0000
- [ 1.076000] bcm63xxpart: Partition 3 is nvram offset 7f0000 and length 10000
- [ 1.084000] bcm63xxpart: Partition 4 is linux offset 10000 and length 7e0000
- [ 1.092000] bcm63xxpart: Spare partition is offset 520004 and length 2cfffc
- [ 1.096000] 5 bcm63xxpart partitions found on MTD device physmap-flash.0
- [ 1.104000] Creating 5 MTD partitions on "physmap-flash.0":
- [ 1.112000] 0x000000000000-0x000000010000 : "CFE"
- [ 1.116000] device: 'mtd0': device_add
- [ 1.120000] device: 'mtd0ro': device_add
- [ 1.124000] device: '31:0': device_add
- [ 1.128000] device: 'mtdblock0': device_add
- [ 1.132000] 0x000000010100-0x000000130000 : "kernel"
- [ 1.140000] mtd: partition "kernel" must either start or end on erase block boundary or be smaller than an erase block -- y
- [ 1.152000] device: 'mtd1': device_add
- [ 1.156000] device: 'mtd1ro': device_add
- [ 1.160000] device: '31:1': device_add
- [ 1.164000] device: 'mtdblock1': device_add
- [ 1.168000] 0x000000130000-0x0000007f0000 : "rootfs"
- [ 1.176000] device: 'mtd2': device_add
- [ 1.180000] device: 'mtd2ro': device_add
- [ 1.184000] device: '31:2': device_add
- [ 1.188000] device: 'mtdblock2': device_add
- [ 1.192000] mtd: device 2 (rootfs) set to be root filesystem
- [ 1.200000] mtd: partition "rootfs_data" created automatically, ofs=0x520000, len=0x2d0000
- [ 1.208000] 0x000000520000-0x0000007f0000 : "rootfs_data"
- [ 1.212000] device: 'mtd3': device_add
- [ 1.216000] device: 'mtd3ro': device_add
- [ 1.224000] device: '31:3': device_add
- [ 1.228000] device: 'mtdblock3': device_add
- [ 1.232000] 0x0000007f0000-0x000000800000 : "nvram"
- [ 1.236000] device: 'mtd4': device_add
- [ 1.240000] device: 'mtd4ro': device_add
- [ 1.244000] device: '31:4': device_add
- [ 1.252000] device: 'mtdblock4': device_add
- [ 1.256000] 0x000000010000-0x0000007f0000 : "linux"
- [ 1.260000] device: 'mtd5': device_add
- [ 1.264000] device: 'mtd5ro': device_add
- [ 1.268000] device: '31:5': device_add
- [ 1.272000] device: 'mtdblock5': device_add
- [ 1.280000] driver: 'physmap-flash.0': driver_bound: bound to device 'physmap-flash'
- [ 1.288000] bus: 'platform': really_probe: bound device physmap-flash.0 to driver physmap-flash
- [ 1.296000] bus: 'platform': add driver bcm63xx-spi
- [ 1.300000] bus: 'platform': driver_probe_device: matched device bcm63xx-spi with driver bcm63xx-spi
- [ 1.312000] bus: 'platform': really_probe: probing driver bcm63xx-spi with device bcm63xx-spi
- [ 1.320000] device: 'spi0': device_add
- [ 1.324000] bcm63xx-spi bcm63xx-spi: registered master spi0
- [ 1.328000] bcm63xx-spi bcm63xx-spi: at 0xb0000800 (irq 9, FIFOs size 542)
- [ 1.336000] driver: 'bcm63xx-spi': driver_bound: bound to device 'bcm63xx-spi'
- [ 1.344000] bus: 'platform': really_probe: bound device bcm63xx-spi to driver bcm63xx-spi
- [ 1.352000] bus: 'platform': add driver spi_gpio
- [ 1.360000] bus: 'mdio_bus': add driver Broadcom BCM63XX (1)
- [ 1.364000] bus: 'mdio_bus': add driver Broadcom BCM63XX (2)
- [ 1.372000] bus: 'platform': add driver b53-switch
- [ 1.376000] bus: 'mdio_bus': add driver Broadcom B53 (1)
- [ 1.380000] bus: 'mdio_bus': add driver Broadcom B53 (2)
- [ 1.388000] bus: 'mdio_bus': add driver Broadcom B53 (3)
- [ 1.392000] bus: 'spi': add driver b53-switch
- [ 1.400000] bus: 'platform': add driver bcm63xx_enet_shared
- [ 1.404000] bus: 'platform': driver_probe_device: matched device bcm63xx_enet_shared.0 with driver bcm63xx_enet_shared
- [ 1.416000] bus: 'platform': really_probe: probing driver bcm63xx_enet_shared with device bcm63xx_enet_shared.0
- [ 1.424000] driver: 'bcm63xx_enet_shared.0': driver_bound: bound to device 'bcm63xx_enet_shared'
- [ 1.436000] bus: 'platform': really_probe: bound device bcm63xx_enet_shared.0 to driver bcm63xx_enet_shared
- [ 1.444000] bus: 'platform': add driver bcm63xx_enet
- [ 1.452000] bus: 'platform': add driver bcm63xx_enetsw
- [ 1.456000] bus: 'platform': driver_probe_device: matched device bcm63xx_enetsw.0 with driver bcm63xx_enetsw
- [ 1.464000] bus: 'platform': really_probe: probing driver bcm63xx_enetsw with device bcm63xx_enetsw.0
- [ 1.508000] device: 'eth0': device_add
- [ 1.512000] Registering platform device 'b53-switch'. Parent at platform
- [ 1.520000] device: 'b53-switch': device_add
- [ 1.524000] bus: 'platform': add device b53-switch
- [ 1.532000] bus: 'platform': driver_probe_device: matched device b53-switch with driver b53-switch
- [ 1.540000] bus: 'platform': really_probe: probing driver b53-switch with device b53-switch
- [ 1.548000] b53_common: found switch: BCM63xx, rev 0
- [ 1.556000] driver: 'b53-switch': driver_bound: bound to device 'b53-switch'
- [ 1.560000] bus: 'platform': really_probe: bound device b53-switch to driver b53-switch
- [ 1.572000] driver: 'bcm63xx_enetsw.0': driver_bound: bound to device 'bcm63xx_enetsw'
- [ 1.580000] bus: 'platform': really_probe: bound device bcm63xx_enetsw.0 to driver bcm63xx_enetsw
- [ 1.588000] bus: 'platform': add driver bcm63xx-wdt
- [ 1.592000] bus: 'platform': driver_probe_device: matched device bcm63xx-wdt with driver bcm63xx-wdt
- [ 1.604000] bus: 'platform': really_probe: probing driver bcm63xx-wdt with device bcm63xx-wdt
- [ 1.612000] device: 'watchdog': device_add
- [ 1.616000] bcm63xx-wdt bcm63xx-wdt: started, timer margin: 30 sec
- [ 1.620000] driver: 'bcm63xx-wdt': driver_bound: bound to device 'bcm63xx-wdt'
- [ 1.628000] bus: 'platform': really_probe: bound device bcm63xx-wdt to driver bcm63xx-wdt
- [ 1.640000] bus: 'platform': add driver leds-gpio
- [ 1.644000] bus: 'platform': driver_probe_device: matched device leds-gpio.0 with driver leds-gpio
- [ 1.652000] bus: 'platform': really_probe: probing driver leds-gpio with device leds-gpio.0
- [ 1.660000] device: 'VR-3025un:green:dsl': device_add
- [ 1.668000] device: 'VR-3025un:green:inet': device_add
- [ 1.672000] device: 'VR-3025un:green:power': device_add
- [ 1.676000] device: 'VR-3025un:red:power': device_add
- [ 1.684000] device: 'VR-3025un:red:inet': device_add
- [ 1.688000] driver: 'leds-gpio.0': driver_bound: bound to device 'leds-gpio'
- [ 1.696000] bus: 'platform': really_probe: bound device leds-gpio.0 to driver leds-gpio
- [ 1.704000] TCP: cubic registered
- [ 1.708000] NET: Registered protocol family 17
- [ 1.712000] 8021q: 802.1Q VLAN Support v1.8
- [ 1.720000] device: 'cpu_dma_latency': device_add
- [ 1.724000] device: 'network_latency': device_add
- [ 1.728000] device: 'network_throughput': device_add
- [ 1.740000] VFS: Mounted root (squashfs filesystem) readonly on device 31:2.
- [ 1.748000] Freeing unused kernel memory: 176K (80314000 - 80340000)
- procd: Console is alive
- procd: - watchdog -
- procd: - preinit -
- ifconfig: SIOCGIFFLAGS: No such device
- Press the [f] key and hit [enter] to enter failsafe mode
- Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level
- [ 6.092000] bus: 'usb': registered
- [ 6.096000] bus: 'usb': add driver usbfs
- [ 6.100000] usbcore: registered new interface driver usbfs
- [ 6.104000] bus: 'usb': add driver hub
- [ 6.108000] usbcore: registered new interface driver hub
- [ 6.116000] bus: 'usb': add driver usb
- [ 6.120000] usbcore: registered new device driver usb
- [ 6.196000] device class 'scsi_host': registering
- [ 6.200000] bus: 'scsi': registered
- [ 6.204000] device class 'scsi_device': registering
- [ 6.212000] SCSI subsystem initialized
- [ 6.220000] device class 'scsi_disk': registering
- [ 6.224000] bus: 'scsi': add driver sd
- [ 6.236000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
- [ 6.244000] ehci-platform: EHCI generic platform driver
- [ 6.248000] bus: 'platform': add driver ehci-platform
- [ 6.256000] bus: 'platform': driver_probe_device: matched device ehci-platform with driver ehci-platform
- [ 6.264000] bus: 'platform': really_probe: probing driver ehci-platform with device ehci-platform
- [ 6.376000] ehci-platform ehci-platform: EHCI Host Controller
- [ 6.380000] ehci-platform ehci-platform: new USB bus registered, assigned bus number 1
- [ 6.388000] ehci-platform ehci-platform: irq 15, io mem 0xb0001500
- [ 6.408000] ehci-platform ehci-platform: USB 2.0 started, EHCI 1.00, overcurrent ignored
- [ 6.416000] device: 'usb1': device_add
- [ 6.420000] bus: 'usb': add device usb1
- [ 6.424000] bus: 'usb': driver_probe_device: matched device usb1 with driver usb
- [ 6.432000] bus: 'usb': really_probe: probing driver usb with device usb1
- [ 6.436000] device: '1-0:1.0': device_add
- [ 6.440000] bus: 'usb': add device 1-0:1.0
- [ 6.448000] bus: 'usb': driver_probe_device: matched device 1-0:1.0 with driver hub
- [ 6.456000] bus: 'usb': really_probe: probing driver hub with device 1-0:1.0
- [ 6.460000] hub 1-0:1.0: USB hub found
- [ 6.464000] hub 1-0:1.0: 2 ports detected
- [ 6.468000] device: 'port1': device_add
- [ 6.472000] device: 'port2': device_add
- [ 6.476000] driver: '1-0:1.0': driver_bound: bound to device 'hub'
- [ 6.484000] bus: 'usb': really_probe: bound device 1-0:1.0 to driver hub
- [ 6.492000] device: 'ep_81': device_add
- [ 6.496000] driver: 'usb1': driver_bound: bound to device 'usb'
- [ 6.500000] bus: 'usb': really_probe: bound device usb1 to driver usb
- [ 6.508000] device: 'ep_00': device_add
- [ 6.512000] driver: 'ehci-platform': driver_bound: bound to device 'ehci-platform'
- [ 6.520000] bus: 'platform': really_probe: bound device ehci-platform to driver ehci-platform
- [ 6.532000] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
- [ 6.540000] bus: 'platform': add driver ohci-platform
- [ 6.544000] bus: 'platform': driver_probe_device: matched device ohci-platform with driver ohci-platform
- [ 6.556000] bus: 'platform': really_probe: probing driver ohci-platform with device ohci-platform
- [ 6.564000] ohci-platform ohci-platform: Generic Platform OHCI Controller
- [ 6.572000] ohci-platform ohci-platform: new USB bus registered, assigned bus number 2
- [ 6.580000] ohci-platform ohci-platform: irq 13, io mem 0xb0001600
- [ 6.644000] device: 'usb2': device_add
- [ 6.648000] bus: 'usb': add device usb2
- [ 6.652000] bus: 'usb': driver_probe_device: matched device usb2 with driver usb
- [ 6.660000] bus: 'usb': really_probe: probing driver usb with device usb2
- [ 6.664000] device: '2-0:1.0': device_add
- [ 6.668000] bus: 'usb': add device 2-0:1.0
- [ 6.676000] bus: 'usb': driver_probe_device: matched device 2-0:1.0 with driver hub
- [ 6.684000] bus: 'usb': really_probe: probing driver hub with device 2-0:1.0
- [ 6.688000] hub 2-0:1.0: USB hub found
- [ 6.692000] hub 2-0:1.0: 1 port detected
- [ 6.696000] device: 'port1': device_add
- [ 6.700000] driver: '2-0:1.0': driver_bound: bound to device 'hub'
- [ 6.708000] bus: 'usb': really_probe: bound device 2-0:1.0 to driver hub
- [ 6.716000] device: 'ep_81': device_add
- [ 6.720000] driver: 'usb2': driver_bound: bound to device 'usb'
- [ 6.724000] bus: 'usb': really_probe: bound device usb2 to driver usb
- [ 6.732000] device: 'ep_00': device_add
- [ 6.736000] driver: 'ohci-platform': driver_bound: bound to device 'ohci-platform'
- [ 6.744000] bus: 'platform': really_probe: bound device ohci-platform to driver ohci-platform
- [ 6.752000] bus: 'pci': add driver ohci_hcd
- [ 6.776000] bus: 'usb': add driver usb-storage
- [ 6.780000] usbcore: registered new interface driver usb-storage
- kmod: ran 1 iterations
- [ 8.184000] jffs2: notice: (242) jffs2_build_xattr_subsystem: complete building xattr subsystem, 1 of xdatum (0 unchecked,.
- mount_root: jffs2 is ready
- [ 8.232000] jffs2: notice: (239) jffs2_build_xattr_subsystem: complete building xattr subsystem, 1 of xdatum (0 unchecked,.
- ifconfig: SIOCGIFFLAGS: No such device
- procd: - early -
- procd: - watchdog -
- procd: - ubus -
- procd: - init -
- Please press Enter to activate this console.
- [ 10.908000] Loading modules backported from Linux version master-2013-11-05-0-gafa3093
- [ 10.916000] Backport generated by backports.git backports-20130802-0-gdb67a3f
- [ 10.932000] nf_conntrack version 0.5.0 (961 buckets, 3844 max)
- [ 11.004000] xt_time: kernel timezone is -0000
- [ 11.036000] device class 'ieee80211': registering
- [ 11.040000] Registering platform device 'regulatory.0'. Parent at platform
- [ 11.048000] device: 'regulatory.0': device_add
- [ 11.052000] bus: 'platform': add device regulatory.0
- [ 11.060000] cfg80211: Calling CRDA to update world regulatory domain
- [ 11.072000] cfg80211: World regulatory domain updated:
- [ 11.080000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
- [ 11.088000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
- [ 11.088000] ip_tables: (C) 2000-2006 Netfilter Core Team
- [ 11.100000] cfg80211: (2457000 KHz - 2482000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
- [ 11.108000] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
- [ 11.116000] cfg80211: (5170000 KHz - 5250000 KHz @ 80000 KHz), (300 mBi, 2000 mBm)
- [ 11.124000] cfg80211: (5735000 KHz - 5835000 KHz @ 80000 KHz), (300 mBi, 2000 mBm)
- [ 11.132000] cfg80211: (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 0 mBm)
- [ 11.284000] bus: 'pci': add driver ath9k
- [ 11.288000] bus: 'pci': driver_probe_device: matched device 0000:00:01.0 with driver ath9k
- [ 11.296000] bus: 'pci': really_probe: probing driver ath9k with device 0000:00:01.0
- [ 11.304000] PCI: Enabling device 0000:00:01.0 (0000 -> 0002)
- [ 12.872000] ath: EEPROM regdomain: 0x37
- [ 12.876000] ath: EEPROM indicates we should expect a direct regpair map
- [ 12.880000] ath: Country alpha2 being used: AW
- [ 12.884000] ath: Regpair used: 0x37
- [ 12.908000] device: 'phy0': device_add
- [ 12.916000] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'
- [ 12.920000] device: 'wlan0': device_add
- [ 12.944000] device: 'ath9k-phy0': device_add
- [ 12.948000] cfg80211: Calling CRDA for country: AW
- [ 12.956000] cfg80211: Regulatory domain changed to country: AW
- [ 12.960000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
- [ 12.968000] cfg80211: (2402000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 2000 mBm)
- [ 12.976000] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (N/A, 2000 mBm)
- [ 12.984000] cfg80211: (5250000 KHz - 5330000 KHz @ 40000 KHz), (N/A, 2000 mBm)
- [ 12.992000] cfg80211: (5490000 KHz - 5710000 KHz @ 40000 KHz), (N/A, 2700 mBm)
- [ 13.000000] ieee80211 phy0: Atheros AR9280 Rev:2 mem=0xc0400000, irq=21
- [ 13.008000] driver: '0000:00:01.0': driver_bound: bound to device 'ath9k'
- [ 13.012000] bus: 'pci': really_probe: bound device 0000:00:01.0 to driver ath9k
- [ 19.720000] device: 'br-lan': device_add
- [ 19.732000] device: 'eth0.1': device_add
- [ 19.744000] device eth0.1 entered promiscuous mode
- [ 19.748000] device eth0 entered promiscuous mode
- [ 19.760000] br-lan: port 1(eth0.1) entered forwarding state
- [ 19.764000] br-lan: port 1(eth0.1) entered forwarding state
- [ 21.768000] br-lan: port 1(eth0.1) entered forwarding state
- procd: - init complete -
- BusyBox v1.19.4 (2013-12-10 20:30:01 CET) built-in shell (ash)
- Enter 'help' for a list of built-in commands.
- _______ ________ __
- | |.-----.-----.-----.| | | |.----.| |_
- | - || _ | -__| || | | || _|| _|
- |_______|| __|_____|__|__||________||__| |____|
- |__| W I R E L E S S F R E E D O M
- ----------------------------------------------BARRIER BREAKER (Bleeding Edge, r39034)
- -----------------------------------------------------
- * 1/2 oz Galliano Pour all ingredients into
- * 4 oz cold Coffee an irish coffee mug filled
- * 1 1/2 oz Dark Rum with crushed ice. Stir.
- * 2 tsp. Creme de Cacao
- -----------------------------------------------------
- root@OpenWrt:/#
Advertisement
Add Comment
Please, Sign In to add comment
Advertisement