Not a member of Pastebin yet?
Sign Up,
it unlocks many cool features!
- # dmsg: line 5
- # lsmod: line 633
- # lsusb -v: line 643
- yianniBox:~ # dmsg
- [ 0.000000] Booting Linux on physical CPU 0xf00
- [ 0.000000] Initializing cgroup subsys cpuset
- [ 0.000000] Initializing cgroup subsys cpu
- [ 0.000000] Initializing cgroup subsys cpuacct
- [ 0.000000] Linux version 4.4.13 (chewitt@buildbox) (gcc version 5.3.0 (GCC) ) #1 SMP Sat Jun 25 04:53:00 BST 2016
- [ 0.000000] CPU: ARMv7 Processor [410fc075] revision 5 (ARMv7), cr=10c5387d
- [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
- [ 0.000000] Machine model: Raspberry Pi 2 Model B Rev 1.1
- [ 0.000000] cma: Reserved 8 MiB at 0x2e400000
- [ 0.000000] Memory policy: Data cache writealloc
- [ 0.000000] On node 0 totalpages: 192512
- [ 0.000000] free_area_init_node: node 0, pgdat 809298c0, node_mem_map add64000
- [ 0.000000] Normal zone: 1692 pages used for memmap
- [ 0.000000] Normal zone: 0 pages reserved
- [ 0.000000] Normal zone: 192512 pages, LIFO batch:31
- [ 0.000000] [bcm2709_smp_init_cpus] enter (94c0->f3003010)
- [ 0.000000] [bcm2709_smp_init_cpus] ncores=4
- [ 0.000000] PERCPU: Embedded 12 pages/cpu @aefaf000 s17292 r8192 d23668 u49152
- [ 0.000000] pcpu-alloc: s17292 r8192 d23668 u49152 alloc=12*4096
- [ 0.000000] pcpu-alloc: [0] 0 [0] 1 [0] 2 [0] 3
- [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 190820
- [ 0.000000] Kernel command line: root=/dev/ram0 rdinit=/init BOOT_IMAGE=/kernel.img usbcore.autosuspend=-1 dma.dmachans=0x7f35 bcm2708_fb.fbwidth=1824 bcm2708_fb.fbheight=984 bcm2709.boardrev=0xa21041 bcm2709.serial=0xb63a1502 smsc95xx.macaddr=B8:27:EB:3A:15:02 bcm2708_fb.fbswap=1 bcm2709.uart_clock=3000000 bcm2709.disk_led_gpio=47 bcm2709.disk_led_active_low=0 vc_mem.mem_base=0x3dc00000 vc_mem.mem_size=0x3f000000 boot=/dev/mmcblk0p1 disk=/dev/mmcblk0p2 quiet
- [ 0.000000] PID hash table entries: 4096 (order: 2, 16384 bytes)
- [ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
- [ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
- [ 0.000000] Memory: 744208K/770048K available (5459K kernel code, 202K rwdata, 1432K rodata, 2260K init, 396K bss, 17648K reserved, 8192K cma-reserved)
- [ 0.000000] Virtual kernel memory layout:
- [ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB)
- [ 0.000000] fixmap : 0xffc00000 - 0xfff00000 (3072 kB)
- [ 0.000000] vmalloc : 0xaf800000 - 0xff800000 (1280 MB)
- [ 0.000000] lowmem : 0x80000000 - 0xaf000000 ( 752 MB)
- [ 0.000000] modules : 0x7f000000 - 0x80000000 ( 16 MB)
- [ 0.000000] .text : 0x80008000 - 0x806c2ffc (6892 kB)
- [ 0.000000] .init : 0x806c3000 - 0x808f8000 (2260 kB)
- [ 0.000000] .data : 0x808f8000 - 0x8092a998 ( 203 kB)
- [ 0.000000] .bss : 0x8092d000 - 0x80990054 ( 397 kB)
- [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
- [ 0.000000] Hierarchical RCU implementation.
- [ 0.000000] Build-time adjustment of leaf fanout to 32.
- [ 0.000000] NR_IRQS:16 nr_irqs:16 16
- [ 0.000000] Architected cp15 timer(s) running at 19.20MHz (phys).
- [ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x46d987e47, max_idle_ns: 440795202767 ns
- [ 0.000010] sched_clock: 56 bits at 19MHz, resolution 52ns, wraps every 4398046511078ns
- [ 0.000028] Switching to timer-based delay loop, resolution 52ns
- [ 0.000256] Console: colour dummy device 80x30
- [ 0.000464] console [tty0] enabled
- [ 0.000490] Calibrating delay loop (skipped), value calculated using timer frequency.. 38.00 BogoMIPS (lpj=64000)
- [ 0.000511] pid_max: default: 32768 minimum: 301
- [ 0.000684] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes)
- [ 0.000702] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes)
- [ 0.001765] Disabling cpuset control group subsystem
- [ 0.001807] Initializing cgroup subsys io
- [ 0.001839] Initializing cgroup subsys memory
- [ 0.001886] Initializing cgroup subsys devices
- [ 0.001906] Initializing cgroup subsys freezer
- [ 0.001945] CPU: Testing write buffer coherency: ok
- [ 0.002550] CPU0: update cpu_capacity 1024
- [ 0.002570] CPU0: thread -1, cpu 0, socket 15, mpidr 80000f00
- [ 0.002583] [bcm2709_smp_prepare_cpus] enter
- [ 0.002674] Setting up static identity map for 0x8280 - 0x82b4
- [ 0.004912] [bcm2709_boot_secondary] cpu:1 started (0) 16
- [ 0.005203] [bcm2709_secondary_init] enter cpu:1
- [ 0.005254] CPU1: update cpu_capacity 1024
- [ 0.005261] CPU1: thread -1, cpu 1, socket 15, mpidr 80000f01
- [ 0.005799] [bcm2709_boot_secondary] cpu:2 started (0) 18
- [ 0.006030] [bcm2709_secondary_init] enter cpu:2
- [ 0.006059] CPU2: update cpu_capacity 1024
- [ 0.006067] CPU2: thread -1, cpu 2, socket 15, mpidr 80000f02
- [ 0.006627] [bcm2709_boot_secondary] cpu:3 started (0) 18
- [ 0.006838] [bcm2709_secondary_init] enter cpu:3
- [ 0.006867] CPU3: update cpu_capacity 1024
- [ 0.006874] CPU3: thread -1, cpu 3, socket 15, mpidr 80000f03
- [ 0.006960] Brought up 4 CPUs
- [ 0.006987] SMP: Total of 4 processors activated (153.00 BogoMIPS).
- [ 0.006996] CPU: All CPU(s) started in HYP mode.
- [ 0.007004] CPU: Virtualization extensions available.
- [ 0.007657] devtmpfs: initialized
- [ 0.019064] VFP support v0.3: implementor 41 architecture 2 part 30 variant 7 rev 5
- [ 0.019309] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 6370867519511994 ns
- [ 0.020059] pinctrl core: initialized pinctrl subsystem
- [ 0.020841] NET: Registered protocol family 16
- [ 0.026664] DMA: preallocated 4096 KiB pool for atomic coherent allocations
- [ 0.036791] cpuidle: using governor ladder
- [ 0.046819] cpuidle: using governor menu
- [ 0.052372] Serial: AMBA PL011 UART driver
- [ 0.052655] 3f201000.uart: ttyAMA0 at MMIO 0x3f201000 (irq = 87, base_baud = 0) is a PL011 rev2
- [ 0.053178] bcm2835-mbox 3f00b880.mailbox: mailbox enabled
- [ 0.106127] bcm2835-dma 3f007000.dma: DMA legacy API manager at f3007000, dmachans=0x1
- [ 0.106728] SCSI subsystem initialized
- [ 0.107208] usbcore: registered new interface driver usbfs
- [ 0.107317] usbcore: registered new interface driver hub
- [ 0.107438] usbcore: registered new device driver usb
- [ 0.110553] raspberrypi-firmware soc:firmware: Attached to firmware from 2016-06-20 18:18
- [ 0.137927] clocksource: Switched to clocksource arch_sys_counter
- [ 0.149497] NET: Registered protocol family 2
- [ 0.150445] TCP established hash table entries: 8192 (order: 3, 32768 bytes)
- [ 0.150581] TCP bind hash table entries: 8192 (order: 4, 65536 bytes)
- [ 0.150771] TCP: Hash tables configured (established 8192 bind 8192)
- [ 0.150886] UDP hash table entries: 512 (order: 2, 16384 bytes)
- [ 0.150949] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes)
- [ 0.151346] NET: Registered protocol family 1
- [ 0.151775] RPC: Registered named UNIX socket transport module.
- [ 0.151790] RPC: Registered udp transport module.
- [ 0.151800] RPC: Registered tcp transport module.
- [ 0.151809] RPC: Registered tcp NFSv4.1 backchannel transport module.
- [ 0.323710] futex hash table entries: 1024 (order: 4, 65536 bytes)
- [ 0.339714] squashfs: version 4.0 (2009/01/31) Phillip Lougher
- [ 0.341851] NFS: Registering the id_resolver key type
- [ 0.341928] Key type id_resolver registered
- [ 0.341940] Key type id_legacy registered
- [ 0.341972] nfs4filelayout_init: NFSv4 File Layout Driver Registering...
- [ 0.346380] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 252)
- [ 0.346409] io scheduler noop registered (default)
- [ 0.346429] io scheduler deadline registered
- [ 0.346478] io scheduler cfq registered
- [ 0.349293] BCM2708FB: allocated DMA memory ee800000
- [ 0.349334] BCM2708FB: allocated DMA channel 0 @ f3007000
- [ 0.378706] Console: switching to colour frame buffer device 228x61
- [ 1.273714] bcm2835-rng 3f104000.rng: hwrng registered
- [ 1.273911] vc-cma: Videocore CMA driver
- [ 1.273924] vc-cma: vc_cma_base = 0x00000000
- [ 1.273934] vc-cma: vc_cma_size = 0x00000000 (0 MiB)
- [ 1.273944] vc-cma: vc_cma_initial = 0x00000000 (0 MiB)
- [ 1.274200] vc-mem: phys_addr:0x00000000 mem_base=0x3dc00000 mem_size:0x3f000000(1008 MiB)
- [ 1.291572] brd: module loaded
- [ 1.291764] loop: module loaded
- [ 1.294854] nbd: registered device at major 43
- [ 1.304814] vchiq: vchiq_init_state: slot_zero = 0xae880000, is_master = 0
- [ 1.306676] usbcore: registered new interface driver rtsx_usb
- [ 1.306702] Loading iSCSI transport class v2.0-870.
- [ 1.307271] iscsi: registered transport (tcp)
- [ 1.307615] tun: Universal TUN/TAP device driver, 1.6
- [ 1.307628] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
- [ 1.308085] usbcore: registered new interface driver dm9601
- [ 1.308209] usbcore: registered new interface driver smsc95xx
- [ 1.308308] dwc_otg: version 3.00a 10-AUG-2012 (platform bus)
- [ 1.508661] Core Release: 2.80a
- [ 1.508679] Setting default values for core params
- [ 1.508717] Finished setting default values for core params
- [ 1.709120] Using Buffer DMA mode
- [ 1.709135] Periodic Transfer Interrupt Enhancement - disabled
- [ 1.709144] Multiprocessor Interrupt Enhancement - disabled
- [ 1.709155] OTG VER PARAM: 0, OTG VER FLAG: 0
- [ 1.709177] Dedicated Tx FIFOs mode
- [ 1.709556] WARN::dwc_otg_hcd_init:1047: FIQ DMA bounce buffers: virt = 0xae814000 dma = 0xee814000 len=9024
- [ 1.709596] FIQ FSM acceleration enabled for :
- [ 1.709596] Non-periodic Split Transactions
- [ 1.709596] Periodic Split Transactions
- [ 1.709596] High-Speed Isochronous Endpoints
- [ 1.709596] Interrupt/Control Split Transaction hack enabled
- [ 1.709622] dwc_otg: Microframe scheduler enabled
- [ 1.709685] WARN::hcd_init_fiq:413: FIQ on core 1 at 0x803d4d44
- [ 1.709702] WARN::hcd_init_fiq:414: FIQ ASM at 0x803d50a8 length 36
- [ 1.709719] WARN::hcd_init_fiq:439: MPHI regs_base at 0xb0682000
- [ 1.709800] dwc_otg 3f980000.usb: DWC OTG Controller
- [ 1.709851] dwc_otg 3f980000.usb: new USB bus registered, assigned bus number 1
- [ 1.709896] dwc_otg 3f980000.usb: irq 62, io mem 0x00000000
- [ 1.709948] Init: Port Power? op_state=1
- [ 1.709958] Init: Power Port (0)
- [ 1.710201] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
- [ 1.710220] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
- [ 1.710235] usb usb1: Product: DWC OTG Controller
- [ 1.710249] usb usb1: Manufacturer: Linux 4.4.13 dwc_otg_hcd
- [ 1.710263] usb usb1: SerialNumber: 3f980000.usb
- [ 1.711105] hub 1-0:1.0: USB hub found
- [ 1.711160] hub 1-0:1.0: 1 port detected
- [ 1.711644] dwc_otg: FIQ enabled
- [ 1.711656] dwc_otg: NAK holdoff enabled
- [ 1.711665] dwc_otg: FIQ split-transaction FSM enabled
- [ 1.711703] Module dwc_common_port init
- [ 1.711986] usbcore: registered new interface driver uas
- [ 1.712152] usbcore: registered new interface driver usb-storage
- [ 1.712414] mousedev: PS/2 mouse device common for all mice
- [ 1.712596] i2c /dev entries driver
- [ 1.713808] bcm2835-cpufreq: min=600000 max=900000
- [ 1.716363] sdhci: Secure Digital Host Controller Interface driver
- [ 1.716373] sdhci: Copyright(c) Pierre Ossman
- [ 1.716640] sdhost: log_buf @ ae813000 (ee813000)
- [ 1.781277] mmc0: sdhost-bcm2835 loaded - DMA enabled (>1)
- [ 1.781465] sdhci-pltfm: SDHCI platform and OF driver helper
- [ 1.781866] ledtrig-cpu: registered to indicate activity on CPUs
- [ 1.782029] hidraw: raw HID events driver (C) Jiri Kosina
- [ 1.783964] usbcore: registered new interface driver usbhid
- [ 1.783972] usbhid: USB HID core driver
- [ 1.785495] NET: Registered protocol family 10
- [ 1.801848] NET: Registered protocol family 17
- [ 1.801972] Key type dns_resolver registered
- [ 1.802408] Registering SWP/SWPB emulation handler
- [ 1.803040] vc-sm: Videocore shared memory driver
- [ 1.803055] [vc_sm_connected_init]: start
- [ 1.803512] [vc_sm_connected_init]: end - returning 0
- [ 1.803744] console [netcon0] enabled
- [ 1.803752] netconsole: network logging started
- [ 1.803777] of_cfs_init
- [ 1.803858] of_cfs_init: OK
- [ 1.807133] Freeing unused kernel memory: 2260K (806c3000 - 808f8000)
- [ 1.867452] mmc0: host does not support reading read-only switch, assuming write-enable
- [ 1.870885] mmc0: new high speed SDHC card at address aaaa
- [ 1.871534] mmcblk0: mmc0:aaaa SL08G 7.40 GiB
- [ 1.880309] mmcblk0: p1 p2
- [ 1.911406] Indeed it is in host mode hprt0 = 00021501
- [ 2.077997] usb 1-1: new high-speed USB device number 2 using dwc_otg
- [ 2.078204] Indeed it is in host mode hprt0 = 00001101
- [ 2.258298] usb 1-1: New USB device found, idVendor=0424, idProduct=9514
- [ 2.258320] usb 1-1: New USB device strings: Mfr=0, Product=0, SerialNumber=0
- [ 2.259033] hub 1-1:1.0: USB hub found
- [ 2.259129] hub 1-1:1.0: 5 ports detected
- [ 2.477447] EXT4-fs (mmcblk0p2): couldn't mount as ext3 due to feature incompatibilities
- [ 2.478001] EXT4-fs (mmcblk0p2): couldn't mount as ext2 due to feature incompatibilities
- [ 2.513618] EXT4-fs (mmcblk0p2): mounted filesystem with ordered data mode. Opts: (null)
- [ 2.537956] usb 1-1.1: new high-speed USB device number 3 using dwc_otg
- [ 2.631645] usb 1-1.1: New USB device found, idVendor=0424, idProduct=ec00
- [ 2.631670] usb 1-1.1: New USB device strings: Mfr=0, Product=0, SerialNumber=0
- [ 2.634731] smsc95xx v1.0.4
- [ 2.677755] smsc95xx 1-1.1:1.0 eth0: register 'smsc95xx' at usb-3f980000.usb-1.1, smsc95xx USB 2.0 Ethernet, b8:27:eb:3a:15:02
- [ 2.758020] usb 1-1.3: new high-speed USB device number 4 using dwc_otg
- [ 2.852281] usb 1-1.3: New USB device found, idVendor=7392, idProduct=a812
- [ 2.852304] usb 1-1.3: New USB device strings: Mfr=1, Product=2, SerialNumber=3
- [ 2.852315] usb 1-1.3: Product: Edimax AC600 USB
- [ 2.852324] usb 1-1.3: Manufacturer: Realtek
- [ 2.852334] usb 1-1.3: SerialNumber: 00e04c000001
- [ 2.898938] systemd[1]: System time before build time, advancing clock.
- [ 2.903094] random: systemd urandom read with 64 bits of entropy available
- [ 2.912756] systemd[1]: systemd 229 running in system mode. (-PAM -AUDIT -SELINUX -IMA -APPARMOR -SMACK -SYSVINIT -UTMP -LIBCRYPTSETUP -GCRYPT -GNUTLS -ACL -XZ -LZ4 -SECCOMP +BLKID -ELFUTILS +KMOD -IDN)
- [ 2.913325] systemd[1]: Detected architecture arm.
- [ 2.913544] systemd[1]: Running with unpopulated /etc.
- [ 2.913806] systemd[1]: Set hostname to <LibreELEC>.
- [ 2.913930] systemd[1]: Cannot open /etc/machine-id: No such file or directory
- [ 2.983478] systemd[1]: Populated /etc with preset unit settings.
- [ 3.082838] systemd[1]: Listening on Journal Socket (/dev/log).
- [ 3.083358] systemd[1]: Listening on Journal Socket.
- [ 3.083604] systemd[1]: Listening on udev Control Socket.
- [ 3.128730] systemd[1]: Created slice User and Session Slice.
- [ 3.129032] systemd[1]: Listening on udev Kernel Socket.
- [ 3.129288] systemd[1]: Listening on /dev/initctl Compatibility Named Pipe.
- [ 3.129608] systemd[1]: Started Dispatch Password Requests to Console Directory Watch.
- [ 3.129854] systemd[1]: Started Forward Password Requests to Wall Directory Watch.
- [ 3.129934] systemd[1]: Reached target Paths.
- [ 3.130376] systemd[1]: Created slice System Slice.
- [ 3.148569] systemd[1]: Starting Remount Root and Kernel File Systems...
- [ 3.151842] systemd[1]: Mounting Debug File System...
- [ 3.155686] systemd[1]: Starting Mounting swapfile...
- [ 3.159982] systemd[1]: Starting Show Version...
- [ 3.163578] systemd[1]: Starting Setup machine-id...
- [ 3.167103] systemd[1]: Mounting Temporary Directory...
- [ 3.171665] systemd[1]: Starting Create list of required static device nodes for the current kernel...
- [ 3.172566] systemd[1]: Reached target Slices.
- [ 3.175906] systemd[1]: Mounting POSIX Message Queue File System...
- [ 3.179753] systemd[1]: Mounting Variable Directory...
- [ 3.186012] systemd[1]: Mounting Configuration File System...
- [ 3.189810] systemd[1]: Starting Apply Kernel Variables...
- [ 3.197743] systemd[1]: Started Remount Root and Kernel File Systems.
- [ 3.199300] systemd[1]: Started Create list of required static device nodes for the current kernel.
- [ 3.203594] systemd[1]: Starting Create Static Device Nodes in /dev...
- [ 3.208227] systemd[1]: Starting udev Coldplug all Devices...
- [ 3.268306] systemd[1]: Mounted Configuration File System.
- [ 3.268826] systemd[1]: Mounted Variable Directory.
- [ 3.274325] systemd[1]: Started Apply Kernel Variables.
- [ 3.302804] systemd[1]: Mounted Debug File System.
- [ 3.303322] systemd[1]: Mounted POSIX Message Queue File System.
- [ 3.303812] systemd[1]: Mounted Temporary Directory.
- [ 3.324947] systemd[1]: Started Show Version.
- [ 3.328366] systemd[1]: systemd-tmpfiles-setup-dev.service: Main process exited, code=exited, status=1/FAILURE
- [ 3.330324] systemd[1]: Failed to start Create Static Device Nodes in /dev.
- [ 3.331646] systemd[1]: systemd-tmpfiles-setup-dev.service: Unit entered failed state.
- [ 3.331701] systemd[1]: systemd-tmpfiles-setup-dev.service: Failed with result 'exit-code'.
- [ 3.380259] systemd[1]: Started Setup machine-id.
- [ 3.413185] systemd[1]: Started Mounting swapfile.
- [ 3.524309] systemd[1]: Started udev Coldplug all Devices.
- [ 3.666922] systemd[1]: Reached target Swap.
- [ 3.681949] systemd[1]: Starting Journal Service...
- [ 3.682475] systemd[1]: Reached target Local File Systems (Pre).
- [ 3.682938] systemd[1]: Reached target Local File Systems.
- [ 3.686688] systemd[1]: Starting Setup Timezone data...
- [ 3.718511] systemd[1]: Started Setup Timezone data.
- [ 3.758123] systemd[1]: Started Journal Service.
- [ 3.826058] systemd-journald[215]: Received request to flush runtime journal from PID 1
- [ 4.258083] random: nonblocking pool is initialized
- [ 5.328755] Console: switching to colour dummy device 80x30
- [ 5.390217] gpiomem-bcm2835 3f200000.gpiomem: Initialised: Registers at 0x3f200000
- [ 5.405575] bcm2835-wdt 3f100000.watchdog: Broadcom BCM2835 watchdog timer
- [ 5.610653] cfg80211: World regulatory domain updated:
- [ 5.610680] cfg80211: DFS Master region: unset
- [ 5.610689] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time)
- [ 5.610701] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
- [ 5.610713] cfg80211: (2457000 KHz - 2482000 KHz @ 20000 KHz, 92000 KHz AUTO), (N/A, 2000 mBm), (N/A)
- [ 5.610723] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (N/A, 2000 mBm), (N/A)
- [ 5.610734] cfg80211: (5170000 KHz - 5250000 KHz @ 80000 KHz, 160000 KHz AUTO), (N/A, 2000 mBm), (N/A)
- [ 5.610746] cfg80211: (5250000 KHz - 5330000 KHz @ 80000 KHz, 160000 KHz AUTO), (N/A, 2000 mBm), (0 s)
- [ 5.610756] cfg80211: (5490000 KHz - 5730000 KHz @ 160000 KHz), (N/A, 2000 mBm), (0 s)
- [ 5.610766] cfg80211: (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 2000 mBm), (N/A)
- [ 5.610776] cfg80211: (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 0 mBm), (N/A)
- [ 5.873874] RTL871X: module init start
- [ 5.873901] RTL871X: rtl8821au v4.3.20_14803.20150724_beta
- [ 5.873909] RTL871X: build time: Jun 22 2016 16:42:23
- [ 6.028883] RTL871X: rtw_ndev_init(wlan0) if1 mac_addr=74:da:38:61:ae:ee
- [ 6.030679] usbcore: registered new interface driver rtl8821au
- [ 6.030697] RTL871X: module init ret=0
- [ 6.356484] smsc95xx 1-1.1:1.0 eth0: hardware isn't capable of remote wakeup
- [ 6.356702] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
- [ 6.868245] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
- [ 22.627987] usb 1-1.5: new full-speed USB device number 5 using dwc_otg
- [ 22.726599] usb 1-1.5: New USB device found, idVendor=046d, idProduct=c52b
- [ 22.726631] usb 1-1.5: New USB device strings: Mfr=1, Product=2, SerialNumber=0
- [ 22.726647] usb 1-1.5: Product: USB Receiver
- [ 22.726661] usb 1-1.5: Manufacturer: Logitech
- [ 22.747773] logitech-djreceiver 0003:046D:C52B.0003: hiddev0,hidraw0: USB HID v1.11 Device [Logitech USB Receiver] on usb-3f980000.usb-1.5/input2
- [ 22.859156] input: Logitech Anywhere MX as /devices/platform/soc/3f980000.usb/usb1/1-1/1-1.5/1-1.5:1.2/0003:046D:C52B.0003/0003:046D:1017.0004/input/input0
- [ 22.860053] logitech-hidpp-device 0003:046D:1017.0004: input,hidraw1: USB HID v1.11 Mouse [Logitech Anywhere MX] on usb-3f980000.usb-1.5:1
- [ 106.607952] usb 1-1.4: new high-speed USB device number 6 using dwc_otg
- [ 106.702841] usb 1-1.4: New USB device found, idVendor=0bda, idProduct=8176
- [ 106.702867] usb 1-1.4: New USB device strings: Mfr=1, Product=2, SerialNumber=3
- [ 106.702878] usb 1-1.4: Product: 802.11n WLAN Adapter
- [ 106.702888] usb 1-1.4: Manufacturer: Realtek
- [ 106.702898] usb 1-1.4: SerialNumber: 00e04c000001
- [ 106.757013] rtl8192cu driver version=v4.0.2_9000.20130911
- [ 106.757217]
- [ 106.757217] usb_endpoint_descriptor(0):
- [ 106.757229] bLength=7
- [ 106.757242] bDescriptorType=5
- [ 106.757250] bEndpointAddress=81
- [ 106.757256] wMaxPacketSize=200
- [ 106.757261] bInterval=0
- [ 106.757267] RT_usb_endpoint_is_bulk_in = 1
- [ 106.757275]
- [ 106.757275] usb_endpoint_descriptor(1):
- [ 106.757283] bLength=7
- [ 106.757289] bDescriptorType=5
- [ 106.757294] bEndpointAddress=2
- [ 106.757300] wMaxPacketSize=200
- [ 106.757306] bInterval=0
- [ 106.757312] RT_usb_endpoint_is_bulk_out = 2
- [ 106.757320]
- [ 106.757320] usb_endpoint_descriptor(2):
- [ 106.757328] bLength=7
- [ 106.757334] bDescriptorType=5
- [ 106.757339] bEndpointAddress=3
- [ 106.757347] wMaxPacketSize=200
- [ 106.757353] bInterval=0
- [ 106.757360] RT_usb_endpoint_is_bulk_out = 3
- [ 106.757366]
- [ 106.757366] usb_endpoint_descriptor(3):
- [ 106.757384] bLength=7
- [ 106.757390] bDescriptorType=5
- [ 106.757398] bEndpointAddress=84
- [ 106.757405] wMaxPacketSize=40
- [ 106.757410] bInterval=1
- [ 106.757417] RT_usb_endpoint_is_int_in = 4, Interval = 1
- [ 106.757426] nr_endpoint=4, in_num=2, out_num=2
- [ 106.757426]
- [ 106.757434] USB_SPEED_HIGH
- [ 106.757528] CHIP TYPE: RTL8188C_8192C
- [ 106.757580] register rtw_netdev_ops to netdev_ops
- [ 106.757878] Chip Version ID: VERSION_NORMAL_UMC_CHIP_88C_B_CUT.
- [ 106.757959] RF_Type is 3!!
- [ 106.758498] EEPROM type is E-FUSE
- [ 106.758517] ====> ReadAdapterInfo8192C
- [ 106.758706] Boot from EFUSE, Autoload OK !
- [ 106.895576] EEPROMVID = 0x0bda
- [ 106.895596] EEPROMPID = 0x8176
- [ 106.895604] EEPROMCustomerID : 0x00
- [ 106.895610] EEPROMSubCustomerID: 0x00
- [ 106.895617] RT_CustomerID: 0x00
- [ 106.895629] _ReadMACAddress MAC Address from EFUSE = XX:XX:XX:XX:XX:XX
- [ 106.895639] EEPROMRegulatory = 0x0
- [ 106.895646] _ReadBoardType(0)
- [ 106.895653] BT Coexistance = disable
- [ 106.895662] mlmepriv.ChannelPlan = 0x02
- [ 106.895671] _ReadPSSetting...bHWPwrPindetect(0)-bHWPowerdown(0) ,bSupportRemoteWakeup(0)
- [ 106.895678] ### PS params=> power_mgnt(0),usbss_enable(0) ###
- [ 106.895684] ### AntDivCfg(0)
- [ 106.895692] readAdapterInfo_8192CU(): REPLACEMENT = 1
- [ 106.895700] <==== ReadAdapterInfo8192C in 136 ms
- [ 106.896550] rtw_macaddr_cfg MAC Address = XX:XX:XX:XX:XX:XX
- [ 106.896568] bDriverStopped:1, bSurpriseRemoved:0, bup:0, hw_init_completed:0
- [ 106.898345] _rtw_drv_register_netdev, MAC Address (if1) = XX:XX:XX:XX:XX:XX
- [ 106.898554] usbcore: registered new interface driver rtl8192cu
- [ 106.899835] +871x_drv - drv_open, bup=0
- [ 106.904664] ===> FirmwareDownload91C() fw:Rtl819XFwImageArray_UMC_B
- [ 106.904691] FirmwareDownload92C accquire FW from embedded image
- [ 106.904701] fw_ver=v88, fw_subver=2, sig=0x88c0
- [ 106.948223] fw download ok!
- [ 106.948247] Set RF Chip ID to RF_6052 and RF type to 1T1R.
- [ 107.310519] IQK:Start!!!
- [ 107.320020] Path A IQK Success!!
- [ 107.326935] Path A IQK Success!!
- [ 107.333084] IQK: final_candidate is 0
- [ 107.333109] IQK: RegE94=104 RegE9C=12 RegEA4=f9 RegEAC=0 RegEB4=0 RegEBC=0 RegEC4=0 RegECC=0
- [ 107.333109] Path A IQ Calibration Success !
- [ 107.445723] pdmpriv->TxPowerTrackControl = 1
- [ 107.452390] rtl8192cu_hal_init in 553ms
- [ 107.463003] MAC Address = XX:XX:XX:XX:XX:XX
- [ 107.463230] -871x_drv - drv_open, bup=1
- [ 107.463402] IPv6: ADDRCONF(NETDEV_UP): wlan1: link is not ready
- [ 107.471965] [rtw_wx_set_pmkid] IW_PMKSA_FLUSH!
- [ 107.472007] set_mode = IW_MODE_INFRA
- [ 107.472208] =>rtw_wx_set_essid
- [ 107.472223] ssid=g�isQ�J�)ͺ����F|�T����vZ.c3�ɚ, len=32
- [ 107.472233] Set SSID under fw_state=0x00000008
- [ 107.472263] <=rtw_wx_set_essid, ret 0
- [ 107.473521] hw_var_set_opmode()-4236 mode = 2
- [ 107.501447] [rtw_wx_set_pmkid] IW_PMKSA_FLUSH!
- [ 108.820680] survey done event(2e) band:0 for wlan1
- [ 108.820729] rtw_select_and_join_from_scanned_queue: return _FAIL(candidate == NULL)
- [ 108.820738] try_to_join, but select scanning queue fail, to_roaming:0
- [ 112.326527] survey done event(1e) band:0 for wlan1
- [ 121.343986] survey done event(1b) band:0 for wlan1
- [ 145.696709] IQK:Start!!!
- [ 145.708908] Path A IQK Success!!
- [ 145.716929] Path A IQK Success!!
- [ 145.721783] IQK: final_candidate is 0
- [ 145.721804] IQK: RegE94=104 RegE9C=f RegEA4=f7 RegEAC=2 RegEB4=0 RegEBC=0 RegEC4=0 RegECC=0
- [ 145.721804] Path A IQ Calibration Success !
- [ 148.357877] survey done event(22) band:0 for wlan1
- [ 168.626233] usb 1-1.3: USB disconnect, device number 4
- [ 168.627067] RTL871X: rtw_cmd_thread: DriverStopped(False) SurpriseRemoved(True) break at line 564
- [ 168.638046] RTL871X: rtw_ndev_uninit(wlan0) if1
- [ 168.698367] RTL871X: rtw_dev_unload: driver not in IPS
- [ 170.704778] ###=> usb_read_port_complete => urb status(-71)
- [ 170.704869] ###=> usb_read_port_complete => urb status(-71)
- [ 170.704915] ###=> usb_read_port_complete => urb status(-71)
- [ 170.704961] ###=> usb_read_port_complete => urb status(-71)
- [ 170.705042] ###=> usb_read_port_complete => urb status(-71)
- [ 170.705053] [dvobj:a9d8c600][ERROR] continual_urb_error:5 > 4
- [ 170.705097] usb_read_port_complete()-1284: RX Warning! bDriverStopped(0) OR bSurpriseRemoved(1) bReadPortCancel(0)
- [ 170.705156] usb_read_port_complete()-1284: RX Warning! bDriverStopped(0) OR bSurpriseRemoved(1) bReadPortCancel(0)
- [ 170.705198] usb_read_port_complete()-1284: RX Warning! bDriverStopped(0) OR bSurpriseRemoved(1) bReadPortCancel(0)
- [ 170.930431] usb 1-1.4: USB disconnect, device number 6
- [ 170.930676] +rtw_dev_remove
- [ 170.930732] (2)871x_drv - drv_close, bup=1, hw_init_completed=1
- [ 170.930757] HW_VAR_BASIC_RATE: BrateCfg(0x15d)
- [ 170.930836] HW_VAR_BASIC_RATE: BrateCfg(0x15d)
- [ 170.930849] rtw_cmd_thread: DriverStopped(0) SurpriseRemoved(1) break at line 482
- [ 170.930857] -871x_drv - drv_close, bup=1
- [ 170.961398] rtw_pm_set_ips IPS_NONE
- [ 170.961430] rtw_sta_flush(wlan1)
- [ 170.961487] ===> rtw_dev_unload
- [ 170.961500] usb_read_port_cancel
- [ 170.961514] usb_write_port_cancel
- [ 170.961611] <=== rtw_dev_unload
- [ 170.961619] rtw_usb_if1_deinit, hw_init_completed=1
- [ 170.962123] free_recv_skb_queue not empty, 4
- [ 170.962188] =====> rtl8192c_free_hal_data =====
- [ 170.962204] <===== rtl8192c_free_hal_data =====
- [ 170.962249] -r871xu_dev_remove, done
- [ 172.664602] usb 1-1.2: new high-speed USB device number 7 using dwc_otg
- [ 172.759338] usb 1-1.2: New USB device found, idVendor=0bda, idProduct=8176
- [ 172.759361] usb 1-1.2: New USB device strings: Mfr=1, Product=2, SerialNumber=3
- [ 172.759371] usb 1-1.2: Product: 802.11n WLAN Adapter
- [ 172.759381] usb 1-1.2: Manufacturer: Realtek
- [ 172.759391] usb 1-1.2: SerialNumber: 00e04c000001
- [ 172.760325]
- [ 172.760325] usb_endpoint_descriptor(0):
- [ 172.760343] bLength=7
- [ 172.760350] bDescriptorType=5
- [ 172.760356] bEndpointAddress=81
- [ 172.760362] wMaxPacketSize=200
- [ 172.760367] bInterval=0
- [ 172.760373] RT_usb_endpoint_is_bulk_in = 1
- [ 172.760379]
- [ 172.760379] usb_endpoint_descriptor(1):
- [ 172.760387] bLength=7
- [ 172.760393] bDescriptorType=5
- [ 172.760415] bEndpointAddress=2
- [ 172.760421] wMaxPacketSize=200
- [ 172.760426] bInterval=0
- [ 172.760432] RT_usb_endpoint_is_bulk_out = 2
- [ 172.760438]
- [ 172.760438] usb_endpoint_descriptor(2):
- [ 172.760446] bLength=7
- [ 172.760451] bDescriptorType=5
- [ 172.760456] bEndpointAddress=3
- [ 172.760462] wMaxPacketSize=200
- [ 172.760467] bInterval=0
- [ 172.760472] RT_usb_endpoint_is_bulk_out = 3
- [ 172.760480]
- [ 172.760480] usb_endpoint_descriptor(3):
- [ 172.760488] bLength=7
- [ 172.760493] bDescriptorType=5
- [ 172.760499] bEndpointAddress=84
- [ 172.760504] wMaxPacketSize=40
- [ 172.760510] bInterval=1
- [ 172.760516] RT_usb_endpoint_is_int_in = 4, Interval = 1
- [ 172.760524] nr_endpoint=4, in_num=2, out_num=2
- [ 172.760524]
- [ 172.760531] USB_SPEED_HIGH
- [ 172.760573] CHIP TYPE: RTL8188C_8192C
- [ 172.760608] register rtw_netdev_ops to netdev_ops
- [ 172.760768] Chip Version ID: VERSION_NORMAL_UMC_CHIP_88C_B_CUT.
- [ 172.760781] RF_Type is 3!!
- [ 172.761106] EEPROM type is E-FUSE
- [ 172.761119] ====> ReadAdapterInfo8192C
- [ 172.761323] Boot from EFUSE, Autoload OK !
- [ 172.855871] EEPROMVID = 0x0bda
- [ 172.855893] EEPROMPID = 0x8176
- [ 172.855900] EEPROMCustomerID : 0x00
- [ 172.855906] EEPROMSubCustomerID: 0x00
- [ 172.855912] RT_CustomerID: 0x00
- [ 172.855923] _ReadMACAddress MAC Address from EFUSE = XX:XX:XX:XX:XX:XX
- [ 172.855933] EEPROMRegulatory = 0x0
- [ 172.855939] _ReadBoardType(0)
- [ 172.855946] BT Coexistance = disable
- [ 172.855953] mlmepriv.ChannelPlan = 0x02
- [ 172.855962] _ReadPSSetting...bHWPwrPindetect(0)-bHWPowerdown(0) ,bSupportRemoteWakeup(0)
- [ 172.855970] ### PS params=> power_mgnt(0),usbss_enable(0) ###
- [ 172.855976] ### AntDivCfg(0)
- [ 172.855982] readAdapterInfo_8192CU(): REPLACEMENT = 1
- [ 172.855991] <==== ReadAdapterInfo8192C in 96 ms
- [ 172.856876] rtw_macaddr_cfg MAC Address = XX:XX:XX:XX:XX:XX
- [ 172.856895] bDriverStopped:1, bSurpriseRemoved:0, bup:0, hw_init_completed:0
- [ 172.858464] _rtw_drv_register_netdev, MAC Address (if1) = XX:XX:XX:XX:XX:XX
- [ 172.860834] +871x_drv - drv_open, bup=0
- [ 172.864471] ===> FirmwareDownload91C() fw:Rtl819XFwImageArray_UMC_B
- [ 172.864494] FirmwareDownload92C accquire FW from embedded image
- [ 172.864503] fw_ver=v88, fw_subver=2, sig=0x88c0
- [ 172.887028] fw download ok!
- [ 172.887051] Set RF Chip ID to RF_6052 and RF type to 1T1R.
- [ 173.201770] IQK:Start!!!
- [ 173.208174] Path A IQK Success!!
- [ 173.212721] Path A IQK Success!!
- [ 173.215183] IQK: final_candidate is 0
- [ 173.215201] IQK: RegE94=104 RegE9C=10 RegEA4=f7 RegEAC=1 RegEB4=0 RegEBC=0 RegEC4=0 RegECC=0
- [ 173.215201] Path A IQ Calibration Success !
- [ 173.323286] pdmpriv->TxPowerTrackControl = 1
- [ 173.325731] rtl8192cu_hal_init in 466ms
- [ 173.333952] MAC Address = XX:XX:XX:XX:XX:XX
- [ 173.334174] -871x_drv - drv_open, bup=1
- [ 173.334441] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
- [ 173.340997] [rtw_wx_set_pmkid] IW_PMKSA_FLUSH!
- [ 173.341032] set_mode = IW_MODE_INFRA
- [ 173.341182] =>rtw_wx_set_essid
- [ 173.341196] ssid=p�>�A��g>~���k��8\*��;�2�<T��\, len=32
- [ 173.341270] Set SSID under fw_state=0x00000008
- [ 173.341297] <=rtw_wx_set_essid, ret 0
- [ 173.345180] hw_var_set_opmode()-4236 mode = 2
- [ 173.391420] [rtw_wx_set_pmkid] IW_PMKSA_FLUSH!
- [ 174.663456] survey done event(c) band:0 for wlan0
- [ 174.663502] rtw_select_and_join_from_scanned_queue: return _FAIL(candidate == NULL)
- [ 174.663512] try_to_join, but select scanning queue fail, to_roaming:0
- [ 178.329613] survey done event(d) band:0 for wlan0
- [ 187.343775] survey done event(d) band:0 for wlan0
- [ 199.106216] survey done event(10) band:0 for wlan0
- [ 199.110349] wpa_set_auth_algs, AUTH_ALG_OPEN_SYSTEM
- [ 199.110382] set_mode = IW_MODE_INFRA
- [ 199.110586]
- [ 199.110586] wpa_ie(length:22):
- [ 199.110609] 0x30 0x14 0x01 0x00 0x00 0x0f 0xac 0x04
- [ 199.110618] 0x01 0x00 0x00 0x0f 0xac 0x04 0x01 0x00
- [ 199.110628] 0x00 0x0f 0xac 0x02 0x00 0x00 0x00 0x00
- [ 199.111305] hw_var_set_opmode()-4236 mode = 2
- [ 199.111980] SetHwReg8192CU, 5132, RCR= 700060ca
- [ 199.112111] =>rtw_wx_set_essid
- [ 199.112123] ssid=Rogers32680, len=11
- [ 199.112152] Set SSID under fw_state=0x00000008
- [ 199.112179] [by_bssid:0][assoc_ssid:Rogers32680][to_roaming:0] new candidate: Rogers32680(00:fc:8d:49:8d:38, ch1) rssi:-72
- [ 199.112194] rtw_select_and_join_from_scanned_queue: candidate: Rogers32680(00:fc:8d:49:8d:38, ch:1)
- [ 199.112225] link to Artheros AP
- [ 199.112243] <=rtw_wx_set_essid, ret 0
- [ 199.112329] Set BSSID under fw_state=0x00000088
- [ 199.112443] start_join_set_ch_bw: ch=1, bwmode=0, ch_offset=0
- [ 199.232125] link to Artheros AP
- [ 199.241684] OnAuthClient
- [ 199.241737] network.SupportedRates[0]=82
- [ 199.241748] network.SupportedRates[1]=84
- [ 199.241757] network.SupportedRates[2]=8B
- [ 199.241766] network.SupportedRates[3]=96
- [ 199.241785] network.SupportedRates[4]=0C
- [ 199.241795] network.SupportedRates[5]=12
- [ 199.241825] network.SupportedRates[6]=18
- [ 199.241837] network.SupportedRates[7]=24
- [ 199.241846] network.SupportedRates[8]=30
- [ 199.241855] network.SupportedRates[9]=48
- [ 199.241864] network.SupportedRates[10]=60
- [ 199.241873] network.SupportedRates[11]=6C
- [ 199.241883] bssrate_len = 12
- [ 199.254425] OnAssocRsp
- [ 199.254476] report_join_res(10)
- [ 199.254487] rtw_joinbss_update_network
- [ 199.254500] +rtw_update_ht_cap()
- [ 199.254516] rtw_joinbss_update_stainfo
- [ 199.254673] HW_VAR_BASIC_RATE: BrateCfg(0x15d)
- [ 199.254952] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
- [ 199.256182] WMM(0): 0, a42b
- [ 199.256365] WMM(1): 0, a44f
- [ 199.256525] WMM(2): 0, 5e4322
- [ 199.256656] WMM(3): 0, 2f3222
- [ 199.256667] HTOnAssocRsp
- [ 199.262426] update raid entry, mask=0xfffff, arg=0xa0
- [ 199.264017] rtl8192c_set_FwJoinBssReport_cmd mstatus(1)
- [ 199.264981] SetFwRsvdPagePkt
- [ 199.265048] Set RSVD page location to Fw.
- [ 199.266169] =>mlmeext_joinbss_event_callback
- [ 199.272996]
- [ 199.272996] ~~~~stastakey:unicastkey
- [ 199.273376] ~~~~set sta key:groupkey
- [ 199.273397] ==> rtw_set_key algorithm(4),keyid(1),key_mask(0)
- [ 199.277002] SetHwReg8192CU, 5128, RCR= 700060ce
- [ 199.423142] rtl8192c_dm_RF_Saving(): RF_Save
- [ 202.107932] usb 1-1.4: new high-speed USB device number 8 using dwc_otg
- [ 202.202397] usb 1-1.4: New USB device found, idVendor=7392, idProduct=a812
- [ 202.202422] usb 1-1.4: New USB device strings: Mfr=1, Product=2, SerialNumber=3
- [ 202.202434] usb 1-1.4: Product: Edimax AC600 USB
- [ 202.202444] usb 1-1.4: Manufacturer: Realtek
- [ 202.202454] usb 1-1.4: SerialNumber: 00e04c000001
- [ 202.382071] RTL871X: rtw_ndev_init(wlan1) if1 mac_addr=74:da:38:61:ae:ee
- [ 202.821716] IPv6: ADDRCONF(NETDEV_UP): wlan1: link is not ready
- [ 210.236805] OnAction_back
- [ 210.236835] OnAction_back, action=0
- [ 210.236847] issue_action_BA, category=3, action=1, status=0
- [ 210.236926] Drop duplicate management frame with seq_num = 258.
- [ 221.496389] rtl8192c_dm_RF_Saving(): RF_Normal
- [ 222.772715] usb 1-1.5: USB disconnect, device number 5
- [ 225.509873] rtl8192c_dm_RF_Saving(): RF_Save
- [ 274.079825] ~~~~set sta key:groupkey
- [ 274.079858] ==> rtw_set_key algorithm(4),keyid(2),key_mask(0)
- [ 274.083194] SetHwReg8192CU, 5128, RCR= 700060ce
- [ 275.675769] rtl8192c_dm_RF_Saving(): RF_Normal
- [ 279.689144] rtw_issue_addbareq_cmd, p=0
- [ 279.691128] issue_action_BA, category=3, action=0, status=0
- [ 279.691161] BA_starting_seqctrl = 446 for TID=0
- [ 279.697748] OnAction_back
- [ 279.697783] OnAction_back, action=1
- [ 279.697797] agg_enable for TID=0
- [ 279.697825] Drop duplicate management frame with seq_num = 259.
- [ 289.723756] rtl8192c_dm_RF_Saving(): RF_Save
- yianniBox:~ # lsmod
- Module Size Used by
- 8812au 1500982 0
- 8192cu 581876 0
- cfg80211 229449 1 8812au
- bcm2835_wdt 2777 0
- bcm2835_gpiomem 2652 0
- yianniBox:~ # lsusb -v
- Bus 001 Device 005: ID 7392:a812 Edimax Technology Co., Ltd
- Device Descriptor:
- bLength 18
- bDescriptorType 1
- bcdUSB 2.10
- bDeviceClass 0
- bDeviceSubClass 0
- bDeviceProtocol 0
- bMaxPacketSize0 64
- idVendor 0x7392 Edimax Technology Co., Ltd
- idProduct 0xa812
- bcdDevice 2.00
- iManufacturer 1 Realtek
- iProduct 2 Edimax AC600 USB
- iSerial 3 00e04c000001
- bNumConfigurations 1
- Configuration Descriptor:
- bLength 9
- bDescriptorType 2
- wTotalLength 60
- bNumInterfaces 1
- bConfigurationValue 1
- iConfiguration 0
- bmAttributes 0xe0
- Self Powered
- Remote Wakeup
- MaxPower 500mA
- Interface Descriptor:
- bLength 9
- bDescriptorType 4
- bInterfaceNumber 0
- bAlternateSetting 0
- bNumEndpoints 6
- bInterfaceClass 255 Vendor Specific Class
- bInterfaceSubClass 255 Vendor Specific Subclass
- bInterfaceProtocol 255 Vendor Specific Protocol
- iInterface 2 Edimax AC600 USB
- Endpoint Descriptor:
- bLength 7
- bDescriptorType 5
- bEndpointAddress 0x84 EP 4 IN
- bmAttributes 2
- Transfer Type Bulk
- Synch Type None
- Usage Type Data
- wMaxPacketSize 0x0200 1x 512 bytes
- bInterval 0
- Endpoint Descriptor:
- bLength 7
- bDescriptorType 5
- bEndpointAddress 0x05 EP 5 OUT
- bmAttributes 2
- Transfer Type Bulk
- Synch Type None
- Usage Type Data
- wMaxPacketSize 0x0200 1x 512 bytes
- bInterval 0
- Endpoint Descriptor:
- bLength 7
- bDescriptorType 5
- bEndpointAddress 0x06 EP 6 OUT
- bmAttributes 2
- Transfer Type Bulk
- Synch Type None
- Usage Type Data
- wMaxPacketSize 0x0200 1x 512 bytes
- bInterval 0
- Endpoint Descriptor:
- bLength 7
- bDescriptorType 5
- bEndpointAddress 0x87 EP 7 IN
- bmAttributes 3
- Transfer Type Interrupt
- Synch Type None
- Usage Type Data
- wMaxPacketSize 0x0040 1x 64 bytes
- bInterval 3
- Endpoint Descriptor:
- bLength 7
- bDescriptorType 5
- bEndpointAddress 0x08 EP 8 OUT
- bmAttributes 2
- Transfer Type Bulk
- Synch Type None
- Usage Type Data
- wMaxPacketSize 0x0200 1x 512 bytes
- bInterval 0
- Endpoint Descriptor:
- bLength 7
- bDescriptorType 5
- bEndpointAddress 0x09 EP 9 OUT
- bmAttributes 2
- Transfer Type Bulk
- Synch Type None
- Usage Type Data
- wMaxPacketSize 0x0200 1x 512 bytes
- bInterval 0
- Binary Object Store Descriptor:
- bLength 5
- bDescriptorType 15
- wTotalLength 12
- bNumDeviceCaps 1
- USB 2.0 Extension Device Capability:
- bLength 7
- bDescriptorType 16
- bDevCapabilityType 2
- bmAttributes 0x00000002
- HIRD Link Power Management (LPM) Supported
- can't get debug descriptor: Resource temporarily unavailable
- Device Status: 0x0001
- Self Powered
- Bus 001 Device 004: ID 0bda:8176 Realtek Semiconductor Corp. RTL8188CUS 802.11n WLAN Adapter
- Device Descriptor:
- bLength 18
- bDescriptorType 1
- bcdUSB 2.00
- bDeviceClass 0
- bDeviceSubClass 0
- bDeviceProtocol 0
- bMaxPacketSize0 64
- idVendor 0x0bda Realtek Semiconductor Corp.
- idProduct 0x8176 RTL8188CUS 802.11n WLAN Adapter
- bcdDevice 2.00
- iManufacturer 1 Realtek
- iProduct 2 802.11n WLAN Adapter
- iSerial 3 00e04c000001
- bNumConfigurations 1
- Configuration Descriptor:
- bLength 9
- bDescriptorType 2
- wTotalLength 46
- bNumInterfaces 1
- bConfigurationValue 1
- iConfiguration 0
- bmAttributes 0x80
- (Bus Powered)
- MaxPower 500mA
- Interface Descriptor:
- bLength 9
- bDescriptorType 4
- bInterfaceNumber 0
- bAlternateSetting 0
- bNumEndpoints 4
- bInterfaceClass 255 Vendor Specific Class
- bInterfaceSubClass 255 Vendor Specific Subclass
- bInterfaceProtocol 255 Vendor Specific Protocol
- iInterface 0
- Endpoint Descriptor:
- bLength 7
- bDescriptorType 5
- bEndpointAddress 0x81 EP 1 IN
- bmAttributes 2
- Transfer Type Bulk
- Synch Type None
- Usage Type Data
- wMaxPacketSize 0x0200 1x 512 bytes
- bInterval 0
- Endpoint Descriptor:
- bLength 7
- bDescriptorType 5
- bEndpointAddress 0x02 EP 2 OUT
- bmAttributes 2
- Transfer Type Bulk
- Synch Type None
- Usage Type Data
- wMaxPacketSize 0x0200 1x 512 bytes
- bInterval 0
- Endpoint Descriptor:
- bLength 7
- bDescriptorType 5
- bEndpointAddress 0x03 EP 3 OUT
- bmAttributes 2
- Transfer Type Bulk
- Synch Type None
- Usage Type Data
- wMaxPacketSize 0x0200 1x 512 bytes
- bInterval 0
- Endpoint Descriptor:
- bLength 7
- bDescriptorType 5
- bEndpointAddress 0x84 EP 4 IN
- bmAttributes 3
- Transfer Type Interrupt
- Synch Type None
- Usage Type Data
- wMaxPacketSize 0x0040 1x 64 bytes
- bInterval 1
- Device Qualifier (for other device speed):
- bLength 10
- bDescriptorType 6
- bcdUSB 2.00
- bDeviceClass 0
- bDeviceSubClass 0
- bDeviceProtocol 0
- bMaxPacketSize0 64
- bNumConfigurations 1
- can't get debug descriptor: Resource temporarily unavailable
- Device Status: 0x0000
- (Bus Powered)
- Bus 001 Device 003: ID 0424:ec00 Standard Microsystems Corp. SMSC9512/9514 Fast Ethernet Adapter
- Device Descriptor:
- bLength 18
- bDescriptorType 1
- bcdUSB 2.00
- bDeviceClass 255 Vendor Specific Class
- bDeviceSubClass 0
- bDeviceProtocol 1
- bMaxPacketSize0 64
- idVendor 0x0424 Standard Microsystems Corp.
- idProduct 0xec00 SMSC9512/9514 Fast Ethernet Adapter
- bcdDevice 2.00
- iManufacturer 0
- iProduct 0
- iSerial 0
- bNumConfigurations 1
- Configuration Descriptor:
- bLength 9
- bDescriptorType 2
- wTotalLength 39
- bNumInterfaces 1
- bConfigurationValue 1
- iConfiguration 0
- bmAttributes 0xe0
- Self Powered
- Remote Wakeup
- MaxPower 2mA
- Interface Descriptor:
- bLength 9
- bDescriptorType 4
- bInterfaceNumber 0
- bAlternateSetting 0
- bNumEndpoints 3
- bInterfaceClass 255 Vendor Specific Class
- bInterfaceSubClass 0
- bInterfaceProtocol 255
- iInterface 0
- Endpoint Descriptor:
- bLength 7
- bDescriptorType 5
- bEndpointAddress 0x81 EP 1 IN
- bmAttributes 2
- Transfer Type Bulk
- Synch Type None
- Usage Type Data
- wMaxPacketSize 0x0200 1x 512 bytes
- bInterval 0
- Endpoint Descriptor:
- bLength 7
- bDescriptorType 5
- bEndpointAddress 0x02 EP 2 OUT
- bmAttributes 2
- Transfer Type Bulk
- Synch Type None
- Usage Type Data
- wMaxPacketSize 0x0200 1x 512 bytes
- bInterval 0
- Endpoint Descriptor:
- bLength 7
- bDescriptorType 5
- bEndpointAddress 0x83 EP 3 IN
- bmAttributes 3
- Transfer Type Interrupt
- Synch Type None
- Usage Type Data
- wMaxPacketSize 0x0010 1x 16 bytes
- bInterval 4
- Device Qualifier (for other device speed):
- bLength 10
- bDescriptorType 6
- bcdUSB 2.00
- bDeviceClass 255 Vendor Specific Class
- bDeviceSubClass 0
- bDeviceProtocol 1
- bMaxPacketSize0 64
- bNumConfigurations 1
- can't get debug descriptor: Resource temporarily unavailable
- Device Status: 0x0001
- Self Powered
- Bus 001 Device 002: ID 0424:9514 Standard Microsystems Corp. SMC9514 Hub
- Device Descriptor:
- bLength 18
- bDescriptorType 1
- bcdUSB 2.00
- bDeviceClass 9 Hub
- bDeviceSubClass 0
- bDeviceProtocol 2 TT per port
- bMaxPacketSize0 64
- idVendor 0x0424 Standard Microsystems Corp.
- idProduct 0x9514 SMC9514 Hub
- bcdDevice 2.00
- iManufacturer 0
- iProduct 0
- iSerial 0
- bNumConfigurations 1
- Configuration Descriptor:
- bLength 9
- bDescriptorType 2
- wTotalLength 41
- bNumInterfaces 1
- bConfigurationValue 1
- iConfiguration 0
- bmAttributes 0xe0
- Self Powered
- Remote Wakeup
- MaxPower 2mA
- Interface Descriptor:
- bLength 9
- bDescriptorType 4
- bInterfaceNumber 0
- bAlternateSetting 0
- bNumEndpoints 1
- bInterfaceClass 9 Hub
- bInterfaceSubClass 0
- bInterfaceProtocol 1 Single TT
- iInterface 0
- Endpoint Descriptor:
- bLength 7
- bDescriptorType 5
- bEndpointAddress 0x81 EP 1 IN
- bmAttributes 3
- Transfer Type Interrupt
- Synch Type None
- Usage Type Data
- wMaxPacketSize 0x0001 1x 1 bytes
- bInterval 12
- Interface Descriptor:
- bLength 9
- bDescriptorType 4
- bInterfaceNumber 0
- bAlternateSetting 1
- bNumEndpoints 1
- bInterfaceClass 9 Hub
- bInterfaceSubClass 0
- bInterfaceProtocol 2 TT per port
- iInterface 0
- Endpoint Descriptor:
- bLength 7
- bDescriptorType 5
- bEndpointAddress 0x81 EP 1 IN
- bmAttributes 3
- Transfer Type Interrupt
- Synch Type None
- Usage Type Data
- wMaxPacketSize 0x0001 1x 1 bytes
- bInterval 12
- Hub Descriptor:
- bLength 9
- bDescriptorType 41
- nNbrPorts 5
- wHubCharacteristic 0x000d
- Per-port power switching
- Compound device
- Per-port overcurrent protection
- TT think time 8 FS bits
- bPwrOn2PwrGood 50 * 2 milli seconds
- bHubContrCurrent 1 milli Ampere
- DeviceRemovable 0x02
- PortPwrCtrlMask 0xff
- Hub Port Status:
- Port 1: 0000.0503 highspeed power enable connect
- Port 2: 0000.0503 highspeed power enable connect
- Port 3: 0000.0100 power
- Port 4: 0000.0503 highspeed power enable connect
- Port 5: 0000.0100 power
- Device Qualifier (for other device speed):
- bLength 10
- bDescriptorType 6
- bcdUSB 2.00
- bDeviceClass 9 Hub
- bDeviceSubClass 0
- bDeviceProtocol 0 Full speed (or root) hub
- bMaxPacketSize0 64
- bNumConfigurations 1
- can't get debug descriptor: Resource temporarily unavailable
- Device Status: 0x0001
- Self Powered
- Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
- Device Descriptor:
- bLength 18
- bDescriptorType 1
- bcdUSB 2.00
- bDeviceClass 9 Hub
- bDeviceSubClass 0
- bDeviceProtocol 1 Single TT
- bMaxPacketSize0 64
- idVendor 0x1d6b Linux Foundation
- idProduct 0x0002 2.0 root hub
- bcdDevice 4.04
- iManufacturer 3 Linux 4.4.13 dwc_otg_hcd
- iProduct 2 DWC OTG Controller
- iSerial 1 3f980000.usb
- bNumConfigurations 1
- Configuration Descriptor:
- bLength 9
- bDescriptorType 2
- wTotalLength 25
- bNumInterfaces 1
- bConfigurationValue 1
- iConfiguration 0
- bmAttributes 0xe0
- Self Powered
- Remote Wakeup
- MaxPower 0mA
- Interface Descriptor:
- bLength 9
- bDescriptorType 4
- bInterfaceNumber 0
- bAlternateSetting 0
- bNumEndpoints 1
- bInterfaceClass 9 Hub
- bInterfaceSubClass 0
- bInterfaceProtocol 0 Full speed (or root) hub
- iInterface 0
- Endpoint Descriptor:
- bLength 7
- bDescriptorType 5
- bEndpointAddress 0x81 EP 1 IN
- bmAttributes 3
- Transfer Type Interrupt
- Synch Type None
- Usage Type Data
- wMaxPacketSize 0x0004 1x 4 bytes
- bInterval 12
- Hub Descriptor:
- bLength 9
- bDescriptorType 41
- nNbrPorts 1
- wHubCharacteristic 0x0008
- Ganged power switching
- Per-port overcurrent protection
- TT think time 8 FS bits
- bPwrOn2PwrGood 1 * 2 milli seconds
- bHubContrCurrent 0 milli Ampere
- DeviceRemovable 0x00
- PortPwrCtrlMask 0xff
- Hub Port Status:
- Port 1: 0000.0503 highspeed power enable connect
- can't get device qualifier: Resource temporarily unavailable
- can't get debug descriptor: Resource temporarily unavailable
- Device Status: 0x0001
- Self Powered
Add Comment
Please, Sign In to add comment