Advertisement
Not a member of Pastebin yet?
Sign Up,
it unlocks many cool features!
- U-Boot SPL 2013.04-dirty (Jun 02 2013 - 17:48:47)
- musb-hdrc: ConfigData=0xde (UTMI-8, dyn FIFOs, HB-ISO Rx, HB-ISO Tx, SoftConn)
- musb-hdrc: MHDRC RTL version 2.0
- musb-hdrc: setup fifo_mode 4
- musb-hdrc: 28/31 max ep, 16384/16384 memory
- USB Peripheral mode controller at 47401000 using PIO, IRQ 0
- musb-hdrc: ConfigData=0xde (UTMI-8, dyn FIFOs, HB-ISO Rx, HB-ISO Tx, SoftConn)
- musb-hdrc: MHDRC RTL version 2.0
- musb-hdrc: setup fifo_mode 4
- musb-hdrc: 28/31 max ep, 16384/16384 memory
- USB Host mode controller at 47401800 using PIO, IRQ 0
- OMAP SD/MMC: 0
- reading u-boot.img
- reading u-boot.img
- U-Boot 2013.04-dirty (Jun 02 2013 - 17:48:47)
- I2C: ready
- DRAM: 256 MiB
- WARNING: Caches not enabled
- NAND: No NAND device found!!!
- 0 MiB
- MMC: OMAP SD/MMC: 0, OMAP SD/MMC: 1
- *** Warning - readenv() failed, using default environment
- musb-hdrc: ConfigData=0xde (UTMI-8, dyn FIFOs, HB-ISO Rx, HB-ISO Tx, SoftConn)
- musb-hdrc: MHDRC RTL version 2.0
- musb-hdrc: setup fifo_mode 4
- musb-hdrc: 28/31 max ep, 16384/16384 memory
- USB Peripheral mode controller at 47401000 using PIO, IRQ 0
- musb-hdrc: ConfigData=0xde (UTMI-8, dyn FIFOs, HB-ISO Rx, HB-ISO Tx, SoftConn)
- musb-hdrc: MHDRC RTL version 2.0
- musb-hdrc: setup fifo_mode 4
- musb-hdrc: 28/31 max ep, 16384/16384 memory
- USB Host mode controller at 47401800 using PIO, IRQ 0
- Net: <ethaddr> not set. Validating first E-fuse MAC
- cpsw, usb_ether
- Hit any key to stop autoboot: 1 0
- gpio: pin 53 (gpio 53) value is 1
- mmc0 is current device
- gpio: pin 54 (gpio 54) value is 1
- SD/MMC found on device 0
- reading uEnv.txt
- 301 bytes read in 4 ms (73.2 KiB/s)
- Importing environment from mmc ...
- gpio: pin 55 (gpio 55) value is 1
- gpio: pin 56 (gpio 56) value is 1
- Running uenvcmd ...
- reading zImage
- 3246088 bytes read in 375 ms (8.3 MiB/s)
- reading /dtbs/am335x-bone.dtb
- 23382 bytes read in 10 ms (2.2 MiB/s)
- ## Flattened Device Tree blob at 80f80000
- Booting using the fdt blob at 0x80f80000
- Using Device Tree in place at 80f80000, end 80f88b55
- Starting kernel ...
- Uncompressing Linux... done, booting the kernel.
- [ 0.000000] Booting Linux on physical CPU 0x0
- [ 0.000000] Initializing cgroup subsys cpu
- [ 0.000000] Linux version 3.8.13-bone20 (voodoo@zeus) (gcc version 4.7.3 20130328 (prerelease) (crosstool-NG linaro-1.13.1-4.7-2013.04-20130415 - Linaro GCC 2013.04) ) #1 SMP Sun Jun 2 17:41:55 CDT 2013
- [ 0.000000] CPU: ARMv7 Processor [413fc082] revision 2 (ARMv7), cr=10c5387d
- [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
- [ 0.000000] Machine: Generic AM33XX (Flattened Device Tree), model: TI AM335x BeagleBone
- [ 0.000000] Memory policy: ECC disabled, Data cache writeback
- [ 0.000000] AM335X ES1.0 (neon )
- [ 0.000000] PERCPU: Embedded 9 pages/cpu @c0beb000 s14080 r8192 d14592 u36864
- [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 64768
- [ 0.000000] Kernel command line: console=ttyO0,115200n8 root=/dev/mmcblk0p2 ro rootfstype=ext4 rootwait fixrtc
- [ 0.000000] PID hash table entries: 1024 (order: 0, 4096 bytes)
- [ 0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
- [ 0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
- [ 0.000000] __ex_table already sorted, skipping sort
- [ 0.000000] allocated 524288 bytes of page_cgroup
- [ 0.000000] please try 'cgroup_disable=memory' option if you don't want memory cgroups
- [ 0.000000] Memory: 255MB = 255MB total
- [ 0.000000] Memory: 248128k/248128k available, 14016k reserved, 0K highmem
- [ 0.000000] Virtual kernel memory layout:
- [ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB)
- [ 0.000000] fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB)
- [ 0.000000] vmalloc : 0xd0800000 - 0xff000000 ( 744 MB)
- [ 0.000000] lowmem : 0xc0000000 - 0xd0000000 ( 256 MB)
- [ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB)
- [ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB)
- [ 0.000000] .text : 0xc0008000 - 0xc089c150 (8785 kB)
- [ 0.000000] .init : 0xc089d000 - 0xc08e5700 ( 290 kB)
- [ 0.000000] .data : 0xc08e6000 - 0xc0966770 ( 514 kB)
- [ 0.000000] .bss : 0xc0966770 - 0xc09dc7fc ( 473 kB)
- [ 0.000000] Hierarchical RCU implementation.
- [ 0.000000] RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=1.
- [ 0.000000] NR_IRQS:16 nr_irqs:16 16
- [ 0.000000] IRQ: Found an INTC at 0xfa200000 (revision 5.0) with 128 interrupts
- [ 0.000000] Total of 128 interrupts on 1 active controller
- [ 0.000000] OMAP clockevent source: GPTIMER1 at 24000000 Hz
- [ 0.000000] sched_clock: 32 bits at 24MHz, resolution 41ns, wraps every 178956ms
- [ 0.000000] OMAP clocksource: GPTIMER2 at 24000000 Hz
- [ 0.000000] Console: colour dummy device 80x30
- [ 0.000396] Calibrating delay loop... 363.67 BogoMIPS (lpj=354304)
- [ 0.017374] pid_max: default: 32768 minimum: 301
- [ 0.017618] Security Framework initialized
- [ 0.017716] Mount-cache hash table entries: 512
- [ 0.027378] Initializing cgroup subsys cpuacct
- [ 0.027419] Initializing cgroup subsys memory
- [ 0.027490] Initializing cgroup subsys blkio
- [ 0.027656] CPU: Testing write buffer coherency: ok
- [ 0.028287] CPU0: thread -1, cpu 0, socket -1, mpidr 0
- [ 0.028369] Setting up static identity map for 0x805f0eb0 - 0x805f0f08
- [ 0.030118] Brought up 1 CPUs
- [ 0.030144] SMP: Total of 1 processors activated (363.67 BogoMIPS).
- [ 0.031629] devtmpfs: initialized
- [ 0.096836] pinctrl core: initialized pinctrl subsystem
- [ 0.097086] rstctl core: initialized rstctl subsystem
- [ 0.097714] regulator-dummy: no parameters
- [ 0.098294] NET: Registered protocol family 16
- [ 0.099169] DMA: preallocated 256 KiB pool for atomic coherent allocations
- [ 0.109283] pinctrl-single 44e10800.pinmux: 142 pins at pa f9e10800 size 568
- [ 0.110097] platform 49000000.edma: alias fck already exists
- [ 0.110130] platform 49000000.edma: alias fck already exists
- [ 0.110156] platform 49000000.edma: alias fck already exists
- [ 0.111564] OMAP GPIO hardware version 0.1
- [ 0.121504] hw-breakpoint: debug architecture 0x4 unsupported.
- [ 0.123713] cpsw.0: No hwaddr in dt. Using 40:5f:c2:76:73:7d from efuse
- [ 0.123762] cpsw.1: No hwaddr in dt. Using 40:5f:c2:76:73:7e from efuse
- [ 0.137730] bio: create slab <bio-0> at 0
- [ 0.149475] edma-dma-engine edma-dma-engine.0: TI EDMA DMA engine driver
- [ 0.149973] vmmcsd_fixed: 3300 mV
- [ 0.152900] SCSI subsystem initialized
- [ 0.153319] usbcore: registered new interface driver usbfs
- [ 0.153443] usbcore: registered new interface driver hub
- [ 0.153787] usbcore: registered new device driver usb
- [ 0.155982] omap_i2c 44e0b000.i2c: bus 0 rev0.11 at 400 kHz
- [ 0.157638] input: tps65217_pwr_but as /devices/ocp.2/44e0b000.i2c/i2c-0/0-0024/input/input0
- [ 0.159518] DCDC1: at 1800 mV
- [ 0.160788] vdd_mpu: 925 <--> 1325 mV at 1125 mV
- [ 0.162008] vdd_core: 925 <--> 1150 mV at 1100 mV
- [ 0.163139] LDO1: at 1800 mV
- [ 0.164248] LDO2: at 3300 mV
- [ 0.165364] LDO3: 1800 <--> 3300 mV at 3300 mV
- [ 0.166585] LDO4: at 3300 mV
- [ 0.167617] tps65217 0-0024: TPS65217 ID 0x7 version 1.0
- [ 0.168508] omap_i2c 44e0b000.i2c: unable to select pin group
- [ 0.169318] omap_i2c 4819c000.i2c: bus 1 rev0.11 at 100 kHz
- [ 0.172106] omap_i2c 4819c000.i2c: unable to select pin group
- [ 0.172348] media: Linux media interface: v0.10
- [ 0.172455] Linux video capture interface: v2.00
- [ 0.173141] Advanced Linux Sound Architecture Driver Initialized.
- [ 0.174393] NetLabel: Initializing
- [ 0.174416] NetLabel: domain hash size = 128
- [ 0.174429] NetLabel: protocols = UNLABELED CIPSOv4
- [ 0.174565] NetLabel: unlabeled traffic allowed by default
- [ 0.174889] Switching to clocksource gp_timer
- [ 0.230825] NET: Registered protocol family 2
- [ 0.232070] TCP established hash table entries: 2048 (order: 2, 16384 bytes)
- [ 0.232163] TCP bind hash table entries: 2048 (order: 3, 40960 bytes)
- [ 0.232255] TCP: Hash tables configured (established 2048 bind 2048)
- [ 0.232360] TCP: reno registered
- [ 0.232389] UDP hash table entries: 256 (order: 1, 12288 bytes)
- [ 0.232434] UDP-Lite hash table entries: 256 (order: 1, 12288 bytes)
- [ 0.232866] NET: Registered protocol family 1
- [ 0.233635] RPC: Registered named UNIX socket transport module.
- [ 0.233657] RPC: Registered udp transport module.
- [ 0.233670] RPC: Registered tcp transport module.
- [ 0.233683] RPC: Registered tcp NFSv4.1 backchannel transport module.
- [ 0.234808] CPU PMU: probing PMU on CPU 0
- [ 0.234842] hw perfevents: enabled with ARMv7 Cortex-A8 PMU driver, 5 counters available
- [ 0.235382] omap2_mbox_probe: platform not supported
- [ 0.504861] VFS: Disk quotas dquot_6.5.2
- [ 0.505224] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
- [ 0.506539] NFS: Registering the id_resolver key type
- [ 0.506666] Key type id_resolver registered
- [ 0.506684] Key type id_legacy registered
- [ 0.506757] fuse init (API version 7.20)
- [ 0.507746] Btrfs loaded
- [ 0.507929] msgmni has been set to 484
- [ 0.511074] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 250)
- [ 0.511104] io scheduler noop registered
- [ 0.511119] io scheduler deadline registered
- [ 0.511173] io scheduler cfq registered (default)
- [ 0.512763] tps65217-bl tps65217-bl: no platform data provided
- [ 0.512808] tps65217-bl: probe of tps65217-bl failed with error -22
- [ 0.513795] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
- [ 0.516367] omap_uart 44e09000.serial: did not get pins for uart0 error: -19
- [ 0.516742] 44e09000.serial: ttyO0 at MMIO 0x44e09000 (irq = 88) is a OMAP UART0
- [ 1.230115] console [ttyO0] enabled
- [ 1.234832] [drm] Initialized drm 1.1.0 20060810
- [ 1.253556] brd: module loaded
- [ 1.263998] loop: module loaded
- [ 1.267485] at24 0-0050: 32768 byte 24c256 EEPROM, writable, 1 bytes/write
- [ 1.274796] at24 1-0054: 32768 byte 24c256 EEPROM, writable, 1 bytes/write
- [ 1.282090] at24 1-0055: 32768 byte 24c256 EEPROM, writable, 1 bytes/write
- [ 1.289379] at24 1-0056: 32768 byte 24c256 EEPROM, writable, 1 bytes/write
- [ 1.296668] at24 1-0057: 32768 byte 24c256 EEPROM, writable, 1 bytes/write
- [ 1.310722] bone-capemgr bone_capemgr.7: Baseboard: 'A335BONE,00A3,4511BB000450'
- [ 1.318565] bone-capemgr bone_capemgr.7: compatible-baseboard=ti,beaglebone
- [ 1.350115] bone-capemgr bone_capemgr.7: slot #0: 'BeagleBone DVI-D WITH AUDIO CAPE,00A1,Beagleboardtoys,BB-BONE-DVID-02'
- [ 1.391821] bone-capemgr bone_capemgr.7: slot #1: No cape found
- [ 1.428928] bone-capemgr bone_capemgr.7: slot #2: No cape found
- [ 1.466036] bone-capemgr bone_capemgr.7: slot #3: No cape found
- [ 1.472650] bone-capemgr bone_capemgr.7: initialized OK.
- [ 1.478293] bone-capemgr bone_capemgr.7: loader: before slot-0 BB-BONE-DVID-02:00A1 (prio 0)
- [ 1.487158] bone-capemgr bone_capemgr.7: loader: check slot-0 BB-BONE-DVID-02:00A1 (prio 0)
- [ 1.497979] OneNAND driver initializing
- [ 1.503428] usbcore: registered new interface driver cdc_ether
- [ 1.509676] usbcore: registered new interface driver rndis_host
- [ 1.515998] bone-capemgr bone_capemgr.7: loader: after slot-0 BB-BONE-DVID-02:00A1 (prio 0)
- [ 1.524890] usbcore: registered new interface driver cdc_ncm
- [ 1.530872] bone-capemgr bone_capemgr.7: slot #0: Requesting part number/version based 'BB-BONE-DVID-02-00A1.dtbo
- [ 1.542421] Initializing USB Mass Storage driver...
- [ 1.547724] usbcore: registered new interface driver usb-storage
- [ 1.554045] USB Mass Storage support registered.
- [ 1.558945] bone-capemgr bone_capemgr.7: slot #0: Requesting firmware 'BB-BONE-DVID-02-00A1.dtbo' for board-name 'BeagleBone DVI-D WITH AUDIO CAPE', version '00A1'
- [ 1.574407] musb-hdrc: version 6.0, ?dma?, otg (peripheral+host)
- [ 1.581634] musb-hdrc musb-hdrc.0.auto: pdev->id = 0
- [ 1.586922] musb-hdrc musb-hdrc.0.auto: drivers/usb/musb/musb_dsps.c:468 dsps_musb_init: OK
- [ 1.595958] musb-hdrc musb-hdrc.0.auto: *** mode=3
- [ 1.601036] musb-hdrc musb-hdrc.0.auto: *** power=250
- [ 1.607115] musb-hdrc musb-hdrc.1.auto: pdev->id = 1
- [ 1.612380] musb-hdrc musb-hdrc.1.auto: drivers/usb/musb/musb_dsps.c:468 dsps_musb_init: OK
- [ 1.621354] musb-hdrc musb-hdrc.1.auto: *** mode=1
- [ 1.626409] musb-hdrc musb-hdrc.1.auto: *** power=250
- [ 1.631727] musb-hdrc musb-hdrc.1.auto: MUSB HDRC host driver
- [ 1.638170] musb-hdrc musb-hdrc.1.auto: new USB bus registered, assigned bus number 1
- [ 1.646638] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
- [ 1.653784] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
- [ 1.661371] usb usb1: Product: MUSB HDRC host driver
- [ 1.666597] usb usb1: Manufacturer: Linux 3.8.13-bone20 musb-hcd
- [ 1.672909] usb usb1: SerialNumber: musb-hdrc.1.auto
- [ 1.679349] hub 1-0:1.0: USB hub found
- [ 1.683388] hub 1-0:1.0: 1 port detected
- [ 1.689104] mousedev: PS/2 mouse device common for all mice
- [ 1.697569] omap_rtc 44e3e000.rtc: rtc core: registered 44e3e000.rtc as rtc0
- [ 1.705113] 44e3e000.rtc: already running
- [ 1.709622] i2c /dev entries driver
- [ 1.714643] Driver for 1-wire Dallas network protocol.
- [ 1.721540] omap_wdt: OMAP Watchdog Timer Rev 0x01: initial timeout 60 sec
- [ 1.729117] cpuidle: using governor ladder
- [ 1.733457] cpuidle: using governor menu
- [ 1.738053] omap_hsmmc mmc.3: of_parse_phandle_with_args of 'reset' failed
- [ 1.745325] omap_hsmmc mmc.3: Failed to get rstctl; not using any
- [ 1.751767] omap_hsmmc mmc.3: unable to select pin group
- [ 1.757639] edma-dma-engine edma-dma-engine.0: allocated channel for 0:25
- [ 1.764899] edma-dma-engine edma-dma-engine.0: allocated channel for 0:24
- [ 1.772569] mmc.3 supply vmmc_aux not found, using dummy regulator
- [ 1.780728] omap_hsmmc mmc.3: pins are not configured from the driver
- [ 1.816290] pinctrl-single 44e10800.pinmux: pin 44e10854 already requested by 44e10800.pinmux; cannot claim for gpio-leds.6
- [ 1.828053] pinctrl-single 44e10800.pinmux: pin-21 (gpio-leds.6) status -22
- [ 1.835373] pinctrl-single 44e10800.pinmux: could not request pin 21 on device pinctrl-single
- [ 1.844384] leds-gpio gpio-leds.6: pins are not configured from the driver
- [ 1.852865] ledtrig-cpu: registered to indicate activity on CPUs
- [ 1.859733] edma-dma-engine edma-dma-engine.0: allocated channel for 0:36
- [ 1.867022] omap-sham 53100000.sham: hw accel on OMAP rev 4.3
- [ 1.875802] omap-aes 53500000.aes: OMAP AES hw accel rev: 3.2
- [ 1.882401] edma-dma-engine edma-dma-engine.0: allocated channel for 0:5
- [ 1.889629] edma-dma-engine edma-dma-engine.0: allocated channel for 0:6
- [ 1.897887] usbcore: registered new interface driver usbhid
- [ 1.903784] usbhid: USB HID core driver
- [ 1.910833] TCP: cubic registered
- [ 1.914663] NET: Registered protocol family 10
- [ 1.920912] NET: Registered protocol family 17
- [ 1.926067] Key type dns_resolver registered
- [ 1.930940] VFP support v0.3: implementor 41 architecture 3 part 30 variant c rev 3
- [ 1.939151] ThumbEE CPU extension supported.
- [ 1.943708] Registering SWP/SWPB emulation handler
- [ 1.949865] registered taskstats version 1
- [ 1.981872] mmc0: host does not support reading read-only switch. assuming write-enable.
- [ 1.995600] mmc0: new high speed SDHC card at address aaaa
- [ 2.002522] mmcblk0: mmc0:aaaa SU04G 3.69 GiB
- [ 2.007315] davinci_mdio 4a101000.mdio: davinci mdio revision 1.6
- [ 2.013733] davinci_mdio 4a101000.mdio: detected phy mask fffffffe
- [ 2.022581] libphy: 4a101000.mdio: probed
- [ 2.026979] davinci_mdio 4a101000.mdio: phy[0]: device 4a101000.mdio:00, driver SMSC LAN8710/LAN8720
- [ 2.036816] mmcblk0: p1 p2
- [ 2.041543] Detected MACID = 40:5f:c2:76:73:7d
- [ 2.046325] cpsw 4a100000.ethernet: NAPI disabled
- [ 2.053428] omap_rtc 44e3e000.rtc: setting system clock to 2000-01-01 00:00:44 UTC (946684844)
- [ 2.066711] ALSA device list:
- [ 2.069878] No soundcards found.
- [ 2.078870] EXT4-fs (mmcblk0p2): INFO: recovery required on readonly filesystem
- [ 2.086621] EXT4-fs (mmcblk0p2): write access will be enabled during recovery
- [ 3.201940] EXT4-fs (mmcblk0p2): recovery complete
- [ 3.216061] EXT4-fs (mmcblk0p2): mounted filesystem with ordered data mode. Opts: (null)
- [ 3.224654] VFS: Mounted root (ext4 filesystem) readonly on device 179:2.
- [ 3.234745] devtmpfs: mounted
- [ 3.238473] Freeing init memory: 288K
- [ 4.200877] init: ureadahead main process (79) terminated with status 5
- [ 6.241078] bone-capemgr bone_capemgr.7: failed to load firmware 'BB-BONE-DVID-02-00A1.dtbo'
- [ 6.250102] bone-capemgr bone_capemgr.7: loader: failed to load slot-0 BB-BONE-DVID-02:00A1 (prio 0)
- * Loading cpufreq kernel modules... [80G
- [74G[ OK ]
- * CPUFreq Utilities: Setting ondemand CPUFreq governor... [80G * CPU0... [80G
- [74G[ OK ]
- * Starting web server apache2 [80G apache2: Could not reliably determine the server's fully qualified domain name, using 127.0.1.1 for ServerName
- [74G[ OK ]
- Ubuntu 13.04 arm ttyO0
- arm login: ubuntu
- Password:
- The programs included with the Ubuntu system are free software;
- the exact distribution terms for each program are described in the
- individual files in /usr/share/doc/*/copyright.
- Ubuntu comes with ABSOLUTELY NO WARRANTY, to the extent permitted by
- applicable law.
- Welcome to Ubuntu 13.04 (GNU/Linux 3.8.13-bone20 armv7l)
- * Documentation: https://help.ubuntu.com/
- To run a command as administrator (user "root"), use "sudo <command>".
- See "man sudo_root" for details.
- ubuntu@arm:~$ uan name -a
- Linux arm 3.8.13-bone20 #1 SMP Sun Jun 2 17:41:55 CDT 2013 armv7l armv7l armv7l GNU/Linux
- ubuntu@arm:~$ cat /proc/cpuinfo
- processor : 0
- model name : ARMv7 Processor rev 2 (v7l)
- BogoMIPS : 181.83
- Features : swp half thumb fastmult vfp edsp thumbee neon vfpv3 tls
- CPU implementer : 0x41
- CPU architecture: 7
- CPU variant : 0x3
- CPU part : 0xc08
- CPU revision : 2
- Hardware : Generic AM33XX (Flattened Device Tree)
- Revision : 0000
- Serial : 0000000000000000
- ubuntu@arm:~$
Advertisement
Add Comment
Please, Sign In to add comment
Advertisement