Advertisement
Not a member of Pastebin yet?
Sign Up,
it unlocks many cool features!
- U-Boot SPL 2013.04-dirty (Jul 10 2013 - 14:02:53)
- timed out in wait_for_pin: I2C_STAT=0
- Could not probe the EEPROM; something fundamentally wrong on the I2C bus.
- Could not get board ID.
- Unknown board, assuming Beaglebone LT/Black.musb-hdrc: ConfigData=0xde (UTMI-8, dyn FIFOs, HB-ISO Rx, HB-ISO Tx, SoftConn)
- musb-hdrc: MHDRC RTL version 2.0
- musb-hdrc: setup fifo_mode 4
- musb-hdrc: 28/31 max ep, 16384/16384 memory
- USB Peripheral mode controller at 47401000 using PIO, IRQ 0
- musb-hdrc: ConfigData=0xde (UTMI-8, dyn FIFOs, HB-ISO Rx, HB-ISO Tx, SoftConn)
- musb-hdrc: MHDRC RTL version 2.0
- musb-hdrc: setup fifo_mode 4
- musb-hdrc: 28/31 max ep, 16384/16384 memory
- USB Host mode controller at 47401800 using PIO, IRQ 0
- OMAP SD/MMC: 0
- mmc_send_cmd : timeout: No status update
- reading u-boot.img
- reading u-boot.img
- U-Boot 2013.04-dirty (Jul 10 2013 - 14:02:53)
- I2C: ready
- DRAM: 512 MiB
- WARNING: Caches not enabled
- timed out in wait_for_pin: I2C_STAT=0
- Could not probe the EEPROM; something fundamentally wrong on the I2C bus.
- Could not get board ID.
- NAND: No NAND device found!!!
- 0 MiB
- MMC: OMAP SD/MMC: 0, OMAP SD/MMC: 1
- *** Warning - readenv() failed, using default environment
- musb-hdrc: ConfigData=0xde (UTMI-8, dyn FIFOs, HB-ISO Rx, HB-ISO Tx, SoftConn)
- musb-hdrc: MHDRC RTL version 2.0
- musb-hdrc: setup fifo_mode 4
- musb-hdrc: 28/31 max ep, 16384/16384 memory
- USB Peripheral mode controller at 47401000 using PIO, IRQ 0
- musb-hdrc: ConfigData=0xde (UTMI-8, dyn FIFOs, HB-ISO Rx, HB-ISO Tx, SoftConn)
- musb-hdrc: MHDRC RTL version 2.0
- musb-hdrc: setup fifo_mode 4
- musb-hdrc: 28/31 max ep, 16384/16384 memory
- USB Host mode controller at 47401800 using PIO, IRQ 0
- Net: <ethaddr> not set. Validating first E-fuse MAC
- cpsw, usb_ether
- Hit any key to stop autoboot: 0
- gpio: pin 53 (gpio 53) value is 1
- Card did not respond to voltage select!
- mmc0(part 0) is current device
- Card did not respond to voltage select!
- No micro SD card found, setting mmcdev to 1
- mmc_send_cmd : timeout: No status update
- mmc1(part 0) is current device
- mmc_send_cmd : timeout: No status update
- gpio: pin 54 (gpio 54) value is 1
- SD/MMC found on device 1
- reading uEnv.txt
- 26 bytes read in 3 ms (7.8 KiB/s)
- Loaded environment from uEnv.txt
- Importing environment from mmc ...
- gpio: pin 55 (gpio 55) value is 1
- 4385024 bytes read in 768 ms (5.4 MiB/s)
- gpio: pin 56 (gpio 56) value is 1
- 24808 bytes read in 54 ms (448.2 KiB/s)
- Booting from mmc ...
- ## Booting kernel from Legacy Image at 80007fc0 ...
- Image Name: Angstrom/3.8.13/beaglebone
- Image Type: ARM Linux Kernel Image (uncompressed)
- Data Size: 4384960 Bytes = 4.2 MiB
- Load Address: 80008000
- Entry Point: 80008000
- Verifying Checksum ... OK
- ## Flattened Device Tree blob at 80f80000
- Booting using the fdt blob at 0x80f80000
- XIP Kernel Image ... OK
- OK
- Using Device Tree in place at 80f80000, end 80f890e7
- Starting kernel ...
- Uncompressing Linux... done, booting the kernel.
- [ 1.156062] omap_i2c 44e0b000.i2c: controller timed out
- [ 1.156108] tps65217 0-0024: Failed to read INT reg
- [ 1.156127] tps65217 0-0024: Failed to probe pwr_but
- [ 2.156057] omap_i2c 44e0b000.i2c: controller timed out
- [ 3.159962] omap_i2c 44e0b000.i2c: controller timed out
- [ 3.192922] omap2_mbox_probe: platform not supported
- [ 4.262855] omap_i2c 44e0b000.i2c: controller timed out
- [ 5.272378] omap_i2c 44e0b000.i2c: controller timed out
- [ 6.786043] omap_i2c 44e0b000.i2c: controller timed out
- [ 7.797992] omap_i2c 44e0b000.i2c: controller timed out
- [ 9.311447] omap_i2c 44e0b000.i2c: controller timed out
- [ 10.323314] omap_i2c 44e0b000.i2c: controller timed out
- [ 11.836827] omap_i2c 44e0b000.i2c: controller timed out
- [ 12.848574] omap_i2c 44e0b000.i2c: controller timed out
- [ 14.362231] omap_i2c 44e0b000.i2c: controller timed out
- [ 15.373940] omap_i2c 44e0b000.i2c: controller timed out
- [ 16.887708] omap_i2c 44e0b000.i2c: controller timed out
- [ 17.899353] omap_i2c 44e0b000.i2c: controller timed out
- [ 19.413082] omap_i2c 44e0b000.i2c: controller timed out
- [ 20.424717] omap_i2c 44e0b000.i2c: controller timed out
- [ 21.938392] omap_i2c 44e0b000.i2c: controller timed out
- [ 22.950192] omap_i2c 44e0b000.i2c: controller timed out
- [ 24.463794] omap_i2c 44e0b000.i2c: controller timed out
- [ 25.475580] omap_i2c 44e0b000.i2c: controller timed out
- [ 26.989175] omap_i2c 44e0b000.i2c: controller timed out
- [ 28.000918] omap_i2c 44e0b000.i2c: controller timed out
- [ 28.514552] bone-capemgr bone_capemgr.8: Failed to scan baseboard eeprom
- [ 28.539327] omap_hsmmc mmc.4: of_parse_phandle_with_args of 'reset' failed
- [ 28.575599] pinctrl-single 44e10800.pinmux: pin 44e10854 already requested by 44e10800.pinmux; cannot claim for gpio-leds.7
- [ 28.587323] pinctrl-single 44e10800.pinmux: pin-21 (gpio-leds.7) status -22
- [ 28.594634] pinctrl-single 44e10800.pinmux: could not request pin 21 on device pinctrl-single
- [ 28.672354] cpufreq_cpu0: failed to scale voltage up: -22
- [ 28.678277] cpufreq_cpu0: failed to scale voltage up: -22
Advertisement
Add Comment
Please, Sign In to add comment
Advertisement