Diags commands

:-) menu -l
:-) help
EDK Boot Loader commands (help <command> for more info):

 "3dbli2bb2rcv"	Reverse Receiver test - Record LI - 3db down
 "3dbli2bb2rcv2"	Reverse Receiver test -  Playback RCVR/ Record MIC  - 3db down
 "3dbli2bb2spk"	Reverse Speaker test - Record  - 3db down
 "3dbli2bb2spk2"	Reverse Speaker test -  Playback - 3db down
 "aboutCB"	display conrolbit information on the screen
 "aboutdev"	display device information on the screen
 "accdet"	Get ACCDet pin status
 "accel"	Test accelermeter in fct &fatp station
 "accid"	Read Acc Identify
 "accsw"	--[on|off|auto]: Diagnostic Acc3V3
 "adc"		get the ADC value from the PMU
 "als"		[--raw|--iqc|--tilt|--ircal|--luxcal|--lux|--commit|--interrupt]ALS calibration and tests
 "alsprox"	[--ui|--samples|--proxcount|--interval|--gain]; Sample refrences number of samples taken, interval is the wait time in ms between samplesALS and PROX Logging test
 "amcss"	 :Run AudioDE
 "ap2hpi2s2ap"	Codec I2S Loopback Test - Playback/Record Codec
 "ap2hppcm2ap"	Codec PCM Loopback Test - Playback/Record Codec
 "ap2hppcm2ap2"	Codec PCM Loopback Test - Playback HP
 "ap2rcv"	AP to receiver or speaker or HP
 "audioinit"	- Initialize the codec
 "bat"		Read battery information
 "batdev"	Read or Write to battery
 "batdisconnect"	Disable battery power at the terminals.
 "batfwupdate"	Download firmware to battery
 "batgg"	Diag test to check FCC and Ra corruption
 "batqmax"	QMax Cell Test
 "batreadblock"	Read battery block

 "batSN"	Read battery SN
 "battool"	List the Battery information
 "batwriteblock"	Write battery block
 "bbinit"	power on baseband and check BB response
 "bboff"	use gpio single power donwn Baseband
 "bbon"		use gpio single power on Baseband
 "bbsnum"	Read the baseband chip-id serial number, SNUM
 "bl"		BackLight Test
 "blockdevice"	Show information about boot devices
 "BPC"		Switch to Uart to BB passthrough mode
 "bt"		check BT response and verify
 "bthostwake"	Test BT_HOST_WAKE line by checking PMU GPIO10
 "buck"		set the buck voltage value
 "button0"	Test buttons without menu key of the unit
 "buttont"	[--alt] Test buttons on the unit
 "camera"	camera command that can run canned tests.
 "camisp"	camera command that can run in seperat steps.
 "cat"		Print the contents of a file.
 "charge"	set charge for system
 "chipid"	 :Show ChipID
 "clcd"		[--id (--iqc)]
 "clkmon"	[signal/off]; Set Clock Test out pin to specified signal or switch it off
 "codec"	 -[r/w/a][reg][data]
 "compass"	Compass tests
 "confct"	[R G B]
 "crosstalk"	Test for high resistance between dock Rx and Tx lines
 "cvbs"		[get] external Video device
 "d2bb"		Enable dock uart directly to Baseband
 "dacff"	:write 0xffff to DAC's for 1 sec. output on HP/LO
 "debug"	Turns debugging on/off.
 "device"	Interfaces with a devices of the system.
 "dfufile"	Use dfu protocol to transfer file.
 "directory"	 dirdev [*match]; directory listing of dirdev. opt match a substring
 "DisCfg#"	Display CFG systemcfg
 "DisOpts"	Display OPTS systemcfg
 "displayPort"	Tests various DisplayPort functionalities - HotPlugDetect, EDID, BIST patterns, FrameBuffers
 "dumpmemmap"	Dumps memory map
 "duplexaudio"	Duplexes I2s/PCM format audio over an I2s interface specified (relative to the AP).
 "fg"		[STATION ID] 0/1/2/3; Write Control Bit
 "flin2rcv"	:Linein-Receiver, MicIn-LO passthrough
 "flin2rcvh"	:Linein-Receiver, MicIn-LO passthrough
 "flin2spk"	:Linein-Speaker, MicIn-LO passthrough
 "flin2spkh"	:Linein-Speaker, MicIn-LO passthrough
 "fm"		--[port [0|1]|portcfg [i2s|pcm]|mode [master|slave]|rec|pbk|passthrough|len [length]|analyse]
 "fwp"		Test FireWire Present
 "getnonce"	read all control bits
 "gpio"		Test button status of unit
 "gps"		Take the GPS in or out of Reset
 "grape"	 [--power(--on|--off)|--rawdata|--1v8(--on|--off)|--18v(--on|--off)        |--fwdl|--ver|--critical|--trailtest [--iqc]|--ninesquare|--digitest(--board|--grape|--open|--shorts)]
 "grapecs"	: Test SPI4_GRAPE_CS_L
 "gyro"		Gryoscope test
 "help"		[cmd]; Help on cmd or a list of all commands if cmd is ommited
 "hm2bb2hp"	:Audio test-WiredMic to BB to HeadPhone - Record
 "hm2bb2hp2"	:Audio test-WiredMic to BB to HeadPhone - Playback
 "HP"		Tool to init/reset Hightland Park as well as read/write it registers
 "HPct"		Highland Park CloseTalk Setup
 "HPft"		Highland Park FarTalk Setup
 "HPhpm"	Highland Park Audio test-HeadPhone Test:multi tone stereo 8kHz 16bit
 "HPloop"	Highland Park Audio loop back
 "hpm"		:Audio test-HeadPhone Test:multi tone
 "HPplay"	Highland Park Audio Playback from file
 "HPrec"	Highland Park Audio Record to file
 "hps"		:Audio test-HeadPhone Test:single tone
 "HPspr"	Highland Park Simultaneous Audio Playback and Record
 "HPspur"	Highland Park Simultaneous Playback and Record via arbitrary ports
 "i2c"		generic read/write to I2C device
 "i2cdevice"	generic read from I2C device by register
 "iis2mic"	Microphone test - Record
 "iis2mic2"	Microphone test -  Playback
 "iis2rcv"	Receiver test - Record
 "iis2rcv2"	Receiver test -  Playback
 "iis2spk"	Speaker test - Record
 "iis2spk2"	Speaker test -  Playback
 "im2hp"	:Audio test-INT mic hp passthrough
 "im2lo"	:Audio test-INT mic hp passthrough
 "im2rcv"	:Audio test-INT mic - receiver passthrough
 "im2spk"	:Audio test-INT mic spk passthrough
 "imei"		Print IMEI information
 "LCM"		 --on:Turn on the LCD interface
 --off:Turn off the LCD interface
 "legal"	Outputs the copyright for any libraries used by Diags.
 "li2bb2rcv"	Reverse Receiver test - Record LI
 "li2bb2rcv2"	Reverse Receiver test -  Playback RCVR/ Record MIC
 "li2bb2rcv3"	Reverse Receiver test -  Playback LO
 "li2bb2spk"	Reverse Speaker test - Record
 "li2bb2spk2"	Reverse Speaker test -  Playback
 "li2bt2hp"	BlueTooth Test - Playback/Record BlueTooth
 "li2bt2hp2"	BlueTooth Test - Playback HP
 "lilo"		:LineIn to LineOut/HP bypass
 "lin2rcv"	:Linein-Receiver passthrough
 "lin2spk"	:LineIn-Speaker passthrough
 "lipm"		:Audio Test-play recorded wave file
 "lirm"		:Audio test-recordd audio file
 "listclocks"	List frequency of PMGR clocks
 "loopaudio"	Loops I2s/PCM format audio over an I2s interface specified (relative to the AP). [DEPRECATED - use duplexaudio instead.]
 "memrw"	[r/w/o/a] [address] [value] Read/write/or/and from memory
 "menu"		: Navigate menu items in Display
 "micpm"	:Audio Test-play recorded wave file
 "micrm"	:Audio test-recordd audio file
 "mictest"	--[len[length]|passthreshold|override|dumpstart|print|stats]: Internal mic self test
 "mikey"	 Mikey Tests
 "mipi"		 on [lanes(1|2|4)] [bpp(2|4)] [freq] | off | enable | disable | sleep [on|off] | highspeed [on|off] | idle | file | backlight [on|off] | invert [on|off] | fill [hex] [hex] | power [on|off] | gamma [file] | write | longwrite | read | longread
 "mipitest"	[--ecc (--iqc)]
 "nandcsid"	 Read Nand Chip ID and detect ID mismatch
 "nandlayout"	 Verify the Nand layout is correct
 "nandsize"	 Nand testing
 "nandtiming"	 nandtiming write|read|get|set|restore|help [optional args]; See help for complete description
 "nanduid"	 Read Unique ID from each Nand die
 "OTASMS"	Test the OTA and SMS
 "pattern"	[--iqc [#]|--fatp [#]|--other [#] [n]:Test LCD display pattern[n]
 "playaudio"	Plays audio from the selected output(s).
 "pmuadc"	PMU ADC test
 "pmubutton"	pmu button test
 "pmustat"	[all|chipid|btn|vbus|chgr|gpio|misc|temp]
 "pmuswif"	Test pmu swi interface
 "pmutemp"	PMU TEMP test
 "prox"		 Return prox raw data
 "proxcal"	[--samples|--proxcount|--offset|--diode|--interval|--getpower|--stream|--getpower]PROX calibration test
 "quit"		Quit EBL
 "racb"		read all control bits
 "rb"		[STATION ID]; Read Control Bit
 "recordaudio"	Records I2S/PCM audio data from a specified I2S port (relative to the AP)
 "reset"	; Resets the whole system
 "routeaudio"	Sets up audio routing.
 "rstbb"	use bb_rst single reset Baseband
 "rtc"		Set or get the RTC from PMU
 "sdiospeed"	 targetspeed (Hz)
 "setu2sto"	Set u2s timeout in micro secs
 "setvol"	 - Sets volumes (run with no argument for help)
 "setvol"	 set Headphone/LineIn/LineOut
 "simdet"	Sim Tray and Card detect
 "sleep"	Set system to sleep state
 "sn"		Read/Write serial number
 "soldercheck"	Check that strategic SoC solder balls are grounded/soldered
 "strobe"	--[init|set_power <mode> <level>|set_mode <mode>|set_duration <us>|sw_sync|hw_sync|on|off
 "swif"		backlight test using SWIF
 "syscfg"	[init | add | print | list | type] <KEY> <value1> <value2> ...; System Config
 "tag"		Turns tagging of data on/off.
 "tat"		Send"AT+COPS=0" to BB after removing dummy cable
 "temp"		Return various temperatures by SerialIoBB from BB
 "testburnin"	 Bonfire low-level NAND burn-in
 "testCDMADDR"	CDMA DDR test
 "testmemory"	Run data and address patterns to exercise DRAM subsystem
 "u2g"		Switch to Uart to GPS passthrough mode
 "u2s"		 Switch to Uart to SDIO passthrough mode
 "u2u"		Switch to Uart to BT passthrough mode
 "uart"		Test the uart receive command
 "usbp"		Test USB Present
 "version"	Diag Version
 "vfct"		[R G B]
 "vibrator"	Vibrator Test
 "vof"		Video off
 "von"		Video on
 "wait"		[ms]; Wait ms milliseconds
 "wakeevent"	Select wake event for wakeup for PMU STANDBY or Hibernate mode
 "wakeoncall"	test wake on call by checking PMU GPIO2
 "wdmic"	:Audio test-HP mic passthrough
 "wifi"		: WiFi Full Self test
 "wlanhostwake"	Test the WLAN_HOST_WAKE line - PMU GPIO 7