U-Boot 1.1.3 (Jul 16 2010 - 11:25:10) (ALPHA)
SVN revision: 359
Target board: WRG-ND08

Board: Ralink APSoC DRAM:  32 MB
Flash: Bank 0, ID:000322a8, Size 4194304 (0x00400000)
============================================
Ralink UBoot Version: 3.3
--------------------------------------------
ASIC 3883_MP (MAC to MAC 100F MII Mode)
DRAM component: 256 Mbits SDR
DRAM bus: 16 bit
Total memory: 32 MBytes
Flash component: NOR Flash
Date:Jul 16 2010  Time:11:25:10
============================================
icache: sets:512, ways:4, linesz:32 ,total:65536
dcache: sets:256, ways:4, linesz:32 ,total:32768

 GPIO pin 24 reset to switch

Please choose the operation:
   1: Load system code to SDRAM via TFTP.
   2: Load system code then write to Flash via TFTP.
   3: Boot system code via Flash (default).
   4: Entr boot command line interface.
   7: Load Boot Loader code then write to Flash via Serial.
   9: Load Boot Loader code then write to Flash via TFTP.

You choosed 1
                                                                              0
1: System Load Linux to SDRAM via TFTP.
 Please Input new ones /or Ctrl-C to discard
        Input device IP (192.168.2.1) ==:192.168.2.1
        Input server IP (192.168.2.100) ==:192.168.2.100
        Input Linux Kernel filename (u2ram.bin) ==:u2ram.bin
1.set ge1 as normal mode
1.set ge1 as mii mode
enable turbo mii
Using Eth0 (10/100-M) device
TFTP from server 192.168.2.100; our IP address is 192.168.2.1
Filename 'u2ram.bin'.

*loading spam cut by me*

Starting kernel ...

[    0.000000] Linux version 4.4.14 (bracco@bracco-VirtualBox) (gcc version 5.3.0 (OpenWrt GCC 5.3.0 50019) ) #28 Fri Dec 23 14:54:13 UTC 2016
[    0.000000] SoC Type: Ralink RT3883 ver:1 eco:5
[    0.000000] bootconsole [early0] enabled
[    0.000000] CPU0 revision is: 0001974c (MIPS 74Kc)
[    0.000000] MIPS: machine is D-Link DIR-815 A1
[    0.000000] Determined physical RAM map:
[    0.000000]  memory: 02000000 @ 00000000 (usable)
[    0.000000] Initrd not found or empty - disabling initrd
[    0.000000] Zone ranges:
[    0.000000]   Normal   [mem 0x0000000000000000-0x0000000001ffffff]
[    0.000000] Movable zone start for each node
[    0.000000] Early memory node ranges
[    0.000000]   node   0: [mem 0x0000000000000000-0x0000000001ffffff]
[    0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x0000000001ffffff]
[    0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
[    0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 8128
[    0.000000] Kernel command line: console=ttyS0,57600 rootfstype=squashfs,jffs2
[    0.000000] PID hash table entries: 128 (order: -3, 512 bytes)
[    0.000000] Dentry cache hash table entries: 4096 (order: 2, 16384 bytes)
[    0.000000] Inode-cache hash table entries: 2048 (order: 1, 8192 bytes)
[    0.000000] Writing ErrCtl register=00000000
[    0.000000] Readback ErrCtl register=00000000
[    0.000000] Memory: 26240K/32768K available (2883K kernel code, 133K rwdata, 712K rodata, 2216K init, 195K bss, 6528K reserved, 0K cma-reserved)
[    0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[    0.000000] NR_IRQS:256
[    0.000000] CPU Clock: 500MHz
[    0.000000] clocksource: MIPS: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041786 ns
[    0.000012] sched_clock: 32 bits at 250MHz, resolution 4ns, wraps every 8589934590ns
[    0.015489] Calibrating delay loop... 249.44 BogoMIPS (lpj=1247232)
[    0.090663] pid_max: default: 32768 minimum: 301
[    0.100001] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.113027] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.134673] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[    0.154405] pinctrl core: initialized pinctrl subsystem
[    0.165607] NET: Registered protocol family 16
[    0.181573] rt3883-pci 10140000.pci: mode: PCIe
[    1.781292] PCI host bridge /pci@10140000/host-bridge ranges:
[    1.792626]  MEM 0x0000000020000000..0x000000002fffffff
[    1.802977]   IO 0x0000000010160000..0x000000001016ffff
[    1.828289] rt2880_gpio 10000600.gpio: registering 24 gpios
[    1.839373] rt2880_gpio 10000600.gpio: registering 24 irq handlers
[    1.851840] rt2880_gpio 10000638.gpio: registering 16 gpios
[    1.863999] PCI host bridge to bus 0000:00
[    1.872008] pci_bus 0000:00: root bus resource [mem 0x20000000-0x2fffffff]
[    1.885747] pci_bus 0000:00: root bus resource [io  0xffffffff]
[    1.897455] pci_bus 0000:00: root bus resource [??? 0x00000000 flags 0x0]
[    1.910948] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff]
[    1.927311] pci 0000:00:01.0: bridge configuration invalid ([bus 00-00]), reconfiguring
[    1.944041] pci 0000:00:01.0: BAR 8: assigned [mem 0x20000000-0x200fffff]
[    1.957474] pci 0000:00:01.0: BAR 1: assigned [mem 0x20100000-0x2010ffff]
[    1.970930] pci 0000:01:00.0: BAR 0: assigned [mem 0x20000000-0x2000ffff]
[    1.984416] pci 0000:00:01.0: PCI bridge to [bus 01]
[    1.994262] pci 0000:00:01.0:   bridge window [mem 0x20000000-0x200fffff]
[    2.007880] pci 0000:00:01.0: of_irq_parse_pci() failed with rc=-22
[    2.021652] clocksource: Switched to clocksource MIPS
[    2.033726] NET: Registered protocol family 2
[    2.043537] TCP established hash table entries: 1024 (order: 0, 4096 bytes)
[    2.057375] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
[    2.069935] TCP: Hash tables configured (established 1024 bind 1024)
[    2.082764] UDP hash table entries: 256 (order: 0, 4096 bytes)
[    2.094322] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[    2.107241] NET: Registered protocol family 1
[    5.198112] rt-timer 10000100.timer: maximum frequency is 3814Hz
[    5.211299] futex hash table entries: 256 (order: -1, 3072 bytes)
[    5.245915] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    5.257502] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[    5.281144] io scheduler noop registered
[    5.288919] io scheduler deadline registered (default)
[    5.299374] ralink-usb-phy usbphy: invalid resource
[    5.309968] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
[    5.324168] console [ttyS0] disabled
[    5.331174] 10000c00.uartlite: ttyS0 at MMIO 0x10000c00 (irq = 20, base_baud = 2500000) is a Palmchip BK-3103
[    5.350988] console [ttyS0] enabled
[    5.350988] console [ttyS0] enabled
[    5.364715] bootconsole [early0] disabled
[    5.364715] bootconsole [early0] disabled
[    5.382237] 1c000000.nor-flash: Found 1 x16 devices at 0x0 in 16-bit bank. Manufacturer ID 0x0000c2 Chip ID 0x0022a8
[    5.403332] Amd/Fujitsu Extended Query Table at 0x0040
[    5.413594]   Amd/Fujitsu Extended Query version 1.1.
[    5.423668] number of CFI chips: 1
[    5.434594] 6 ofpart partitions found on MTD device 1c000000.nor-flash
[    5.447715] Creating 6 MTD partitions on "1c000000.nor-flash":
[    5.459367] 0x000000000000-0x000000030000 : "uboot"
[    5.471549] 0x000000030000-0x000000034000 : "uboot-env"
[    5.484782] 0x000000034000-0x000000038000 : "factory"
[    5.497648] 0x000000038000-0x000000040000 : "nvram"
[    5.510130] 0x000000040000-0x000000050000 : "devdata"
[    5.523142] 0x000000050000-0x000000400000 : "firmware"
[    5.538339] 2 seama-fw partitions found on MTD device firmware
[    5.550086] 0x000000050040-0x000000190000 : "kernel"
[    5.562635] 0x000000190000-0x000000400000 : "rootfs"
[    5.575230] mtd: device 7 (rootfs) set to be root filesystem
[    5.586657] 1 squashfs-split partitions found on MTD device rootfs
[    5.599007] 0x0000003b0000-0x000000400000 : "rootfs_data"
[    5.615795] libphy: mdio: probed
[    5.624875] IP17xx: Found IP175D at mdio-bus:00
[    5.717889] mtk_soc_eth 10100000.ethernet: connected port 0 to PHY at mdio-bus:00 [uid=02430d80, driver=IC+ IP17xx]
[    5.739785] mtk_soc_eth 10100000.ethernet eth0: mediatek frame engine at 0xb0100000, irq 5
[    5.757152] rt2880_wdt 10000120.watchdog: Initialized
[    5.769224] NET: Registered protocol family 10
[    5.783922] NET: Registered protocol family 17
[    5.793038] bridge: automatic filtering via arp/ip/ip6tables has been deprecated. Update your scripts to load br_netfilter if you need this.
[    5.818226] 8021q: 802.1Q VLAN Support v1.8
[    5.856165] Freeing unused kernel memory: 2216K (803a6000 - 805d0000)
[    5.889161] init: Console is alive
[    5.896426] init: - watchdog -
[    5.948900] usbcore: registered new interface driver usbfs
[    5.960094] usbcore: registered new interface driver hub
[    5.970915] usbcore: registered new device driver usb
[    5.990384] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    6.006125] ehci-platform: EHCI generic platform driver
[    6.021856] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[    6.036449] ohci-platform: OHCI generic platform driver
[    6.058218] init: - preinit -
[    6.215562] 8021q: adding VLAN 0 to HW filter on device eth0
[    6.257849] random: procd urandom read with 9 bits of entropy available
Press the [f] key and hit [enter] to enter failsafe mode
Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level
[    7.711688] mtk_soc_eth 10100000.ethernet eth0: link up (100Mbps/Full duplex)
[    9.478409] procd: - early -
[    9.484565] procd: - watchdog -
[    9.711690] mtk_soc_eth 10100000.ethernet eth0: link down
[   10.089112] procd: - ubus -
[   10.149144] procd: - init -
Please press Enter to activate this console.
[   11.076980] ip6_tables: (C) 2000-2006 Netfilter Core Team
[   11.108728] Loading modules backported from Linux version wt-2016-05-12-0-g7a54796
[   11.123925] Backport generated by backports.git backports-20160216-0-ge3c56e4
[   11.145171] ip_tables: (C) 2000-2006 Netfilter Core Team
[   11.173077] nf_conntrack version 0.5.0 (444 buckets, 1776 max)
[   11.242848] xt_time: kernel timezone is -0000
[   11.352762] PPP generic driver version 2.4.2
[   11.365818] NET: Registered protocol family 24
[   11.419264] PCI: Enabling device 0000:01:00.0 (0000 -> 0002)
[   11.430931] rt2800pci 0000:01:00.0: failed to load eeprom property
[   11.443340] ieee80211 phy0: rt2x00lib_request_eeprom_file: Info - Loading EEPROM data from 'rt2x00pci_1_0.eeprom'.
[   11.464124] rt2800pci 0000:01:00.0: Direct firmware load for rt2x00pci_1_0.eeprom failed with error -2
[   11.482714] rt2800pci 0000:01:00.0: Falling back to user helper
[   11.602362] ieee80211 phy0: rt2x00_set_rt: Info - RT chipset 3071, rev 021c detected
[   11.617926] ieee80211 phy0: rt2x00_set_rf: Info - RF chipset 0008 detected
[   11.678525] ieee80211 phy1: rt2x00_set_rt: Info - RT chipset 3883, rev 0400 detected
[   11.694110] ieee80211 phy1: rt2x00_set_rf: Info - RF chipset 3853 detected
[   22.609531] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[   22.621291] 8021q: adding VLAN 0 to HW filter on device eth0
[   22.705398] device eth0.1 entered promiscuous mode
[   22.715114] device eth0 entered promiscuous mode
[   22.724811] mtk_soc_eth 10100000.ethernet eth0: link up (100Mbps/Full duplex)
[   22.788918] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[   22.833337] IPv6: ADDRCONF(NETDEV_UP): br-lan: link is not ready
[   22.845867] br-lan: port 1(eth0.1) entered forwarding state
[   22.857137] br-lan: port 1(eth0.1) entered forwarding state
[   22.962100] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready
[   24.851770] br-lan: port 1(eth0.1) entered forwarding state