API tools faq
paste
Advertisement
Guest User

Kernel Ka-Ro (3.16)

a guest
May 4th, 2015
504
0
Never
Add comment
Not a member of Pastebin yet? Sign Up, it unlocks many cool features!
text 13.88 KB | None | 0 0
raw download clone embed print report
  1. U-Boot 2013.07-00787-g36ed10c (Mar 24 2015 - 16:02:12)
  2.  
  3. CPU: Freescale i.MX6DL rev1.1 at 792 MHz
  4. Reset cause: POR
  5. Board: Ka-Ro TX6U-8010
  6. I2C: ready
  7. DRAM: 1 GiB
  8. VDDCORE set to 1421mV
  9. VDDSOC set to 1421mV
  10. NAND: 128 MiB
  11. MMC: FSL_SDHC: 0, FSL_SDHC: 1
  12. IPU HW Rev: 4
  13. Temperature: 56 C, calibration data 0x5814fa69
  14. CPU clock set to 792.000 MHz
  15. Baseboard: stk5-v3
  16. MAC addr from fuse: 00:0c:c6:7a:39:63
  17. Net: FEC
  18. Hit any key to stop autoboot: 0
  19.  
  20. Loading from nand0, offset 0x180000
  21. Image Name: Linux-3.16.0-00787-g1fb9d67
  22. Image Type: ARM Linux Kernel Image (uncompressed)
  23. Data Size: 4538088 Bytes = 4.3 MiB
  24. Load Address: 10008000
  25. Entry Point: 10008000
  26. ## Booting kernel from Legacy Image at 18000000 ...
  27. Image Name: Linux-3.16.0-00787-g1fb9d67
  28. Image Type: ARM Linux Kernel Image (uncompressed)
  29. Data Size: 4538088 Bytes = 4.3 MiB
  30. Load Address: 10008000
  31. Entry Point: 10008000
  32. Verifying Checksum ... OK
  33. ## Flattened Device Tree blob at 11000000
  34. Booting using the fdt blob at 0x11000000
  35. Loading Kernel Image ... OK
  36. Loading Device Tree to 4ef3d000, end 4ef4996d ... OK
  37.  
  38. Starting kernel ...
  39.  
  40. Disabling LCD
  41. Uncompressing Linux... done, booting the kernel.
  42. Booting Linux on physical CPU 0x0
  43. Linux version 3.16.0-00787-g1fb9d67 (armsdk@debian) (gcc version 4.7.2 (GCC) ) #1 SMP PREEMPT Tue Mar 24 14:50:36 CET 2015
  44. CPU: ARMv7 Processor [412fc09a] revision 10 (ARMv7), cr=10c5387d
  45. CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
  46. Machine model: Ka-Ro electronics TX6U-801x/-803x Module
  47. cma: CMA: reserved 320 MiB at 3a000000
  48. Memory policy: Data cache writealloc
  49. On node 0 totalpages: 262144
  50. free_area_init_node: node 0, pgdat 80877ec0, node_mem_map bf757000
  51. Normal zone: 2048 pages used for memmap
  52. Normal zone: 0 pages reserved
  53. Normal zone: 262144 pages, LIFO batch:31
  54. PERCPU: Embedded 7 pages/cpu @bf727000 s7808 r8192 d12672 u32768
  55. pcpu-alloc: s7808 r8192 d12672 u32768 alloc=8*4096
  56. pcpu-alloc: [0] 0 [0] 1
  57. Built 1 zonelists in Zone order, mobility grouping on. Total pages: 260096
  58. Kernel command line: init=/linuxrc console=ttymxc0,115200 ro debug panic=1 ubi.mtd=3 root=ubi0:rootfs rootfstype=ubifs rootwait rw mtdparts=gpmi-nand:1m@128k(u-boot),384k(env),7m(linux),121728k(rootfs),128k(dtb),512k(bbt)ro rootflags=sync
  59. PID hash table entries: 4096 (order: 2, 16384 bytes)
  60. Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
  61. Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
  62. Memory: 701920K/1048576K available (6087K kernel code, 219K rwdata, 2100K rodata, 235K init, 447K bss, 346656K reserved, 0K highmem)
  63. Virtual kernel memory layout:
  64. vector : 0xffff0000 - 0xffff1000 ( 4 kB)
  65. fixmap : 0xffc00000 - 0xffe00000 (2048 kB)
  66. vmalloc : 0xc0800000 - 0xff000000 (1000 MB)
  67. lowmem : 0x80000000 - 0xc0000000 (1024 MB)
  68. pkmap : 0x7fe00000 - 0x80000000 ( 2 MB)
  69. modules : 0x7f000000 - 0x7fe00000 ( 14 MB)
  70. .text : 0x80008000 - 0x80806fa8 (8188 kB)
  71. .init : 0x80807000 - 0x80841e80 ( 236 kB)
  72. .data : 0x80842000 - 0x80878f60 ( 220 kB)
  73. .bss : 0x80878f6c - 0x808e8d74 ( 448 kB)
  74. SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
  75. Preemptible hierarchical RCU implementation.
  76. RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=2.
  77. RCU: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2
  78. NR_IRQS:16 nr_irqs:16 16
  79. L2C-310 erratum 769419 enabled
  80. L2C-310 enabling early BRESP for Cortex-A9
  81. L2C-310 full line of zeros enabled for Cortex-A9
  82. L2C-310 ID prefetch enabled, offset 1 lines
  83. L2C-310 dynamic clock gating enabled, standby mode enabled
  84. L2C-310 cache controller enabled, 16 ways, 512 kB
  85. L2C-310: CACHE_ID 0x410000c8, AUX_CTRL 0x76050001
  86. Switching to timer-based delay loop
  87. sched_clock: 32 bits at 66MHz, resolution 15ns, wraps every 65075262448ns
  88. Console: colour dummy device 80x30
  89. Calibrating delay loop (skipped), value calculated using timer frequency.. 132.00 BogoMIPS (lpj=660000)
  90. pid_max: default: 32768 minimum: 301
  91. Mount-cache hash table entries: 2048 (order: 1, 8192 bytes)
  92. Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes)
  93. CPU: Testing write buffer coherency: ok
  94. CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
  95. Setting up static identity map for 0x105c6b50 - 0x105c6ba8
  96. CPU1: Booted secondary processor
  97. CPU1: thread -1, cpu 1, socket 0, mpidr 80000001
  98. Brought up 2 CPUs
  99. SMP: Total of 2 processors activated.
  100. CPU: All CPU(s) started in SVC mode.
  101. devtmpfs: initialized
  102. VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4
  103. pinctrl core: initialized pinctrl subsystem
  104. regulator-dummy: no parameters
  105. NET: Registered protocol family 16
  106. DMA: preallocated 256 KiB pool for atomic coherent allocations
  107. cpuidle: using governor ladder
  108. cpuidle: using governor menu
  109. CPU identified as i.MX6DL, silicon rev 1.1
  110. Use WDOG1 as reset source
  111. vdd1p1: 800 <--> 1375 mV at 1100 mV
  112. vdd3p0: 2800 <--> 3150 mV at 3000 mV
  113. vdd2p5: 2000 <--> 2750 mV at 2400 mV
  114. vddarm: 725 <--> 1450 mV at 1150 mV
  115. vddpu: 725 <--> 1450 mV at 1150 mV
  116. vddsoc: 725 <--> 1450 mV at 1200 mV
  117. imx6dl-pinctrl 20e0000.iomuxc: initialized IMX pinctrl driver
  118. mxs-dma 110000.dma-apbh: initialized
  119. 3V3_ETN: 3300 mV
  120. 2V5: 2500 mV
  121. 3V3: 3300 mV
  122. LCD0 POWER: 3300 mV
  123. LCD1 POWER: 3300 mV
  124. usbh1_vbus: 5000 mV
  125. SCSI subsystem initialized
  126. libata version 3.00 loaded.
  127. usbcore: registered new interface driver usbfs
  128. usbcore: registered new interface driver hub
  129. usbcore: registered new device driver usb
  130. i2c i2c-0: IMX I2C adapter registered
  131. i2c i2c-2: IMX I2C adapter registered
  132. Linux video capture interface: v2.00
  133. pps_core: LinuxPPS API ver. 1 registered
  134. pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
  135. PTP clock support registered
  136. imx-ipuv3 2400000.ipu: IPU DMFC NORMAL mode: 1(0~1), 5B(4,5), 5F(6,7)
  137. Advanced Linux Sound Architecture Driver Initialized.
  138. cfg80211: Calling CRDA to update world regulatory domain
  139. Switched to clocksource mxc_timer1
  140. NET: Registered protocol family 2
  141. TCP established hash table entries: 8192 (order: 3, 32768 bytes)
  142. TCP bind hash table entries: 8192 (order: 4, 65536 bytes)
  143. TCP: Hash tables configured (established 8192 bind 8192)
  144. TCP: reno registered
  145. UDP hash table entries: 512 (order: 2, 16384 bytes)
  146. UDP-Lite hash table entries: 512 (order: 2, 16384 bytes)
  147. NET: Registered protocol family 1
  148. RPC: Registered named UNIX socket transport module.
  149. RPC: Registered udp transport module.
  150. RPC: Registered tcp transport module.
  151. RPC: Registered tcp NFSv4.1 backchannel transport module.
  152. PCI: CLS 0 bytes, default 64
  153. futex hash table entries: 512 (order: 3, 32768 bytes)
  154. NFS: Registering the id_resolver key type
  155. Key type id_resolver registered
  156. Key type id_legacy registered
  157. fuse init (API version 7.23)
  158. msgmni has been set to 2010
  159. io scheduler noop registered
  160. io scheduler deadline registered
  161. io scheduler cfq registered (default)
  162. imx-weim 21b8000.weim: Driver registered.
  163. mxc_sdc_fb fb@2: register mxc display driver lcd
  164. Console: switching to colour frame buffer device 80x30
  165. imx-sdma 20ec000.sdma: loaded firmware 1.1
  166. imx-sdma 20ec000.sdma: initialized
  167. Serial: IMX driver
  168. 2020000.serial: ttymxc0 at MMIO 0x2020000 (irq = 58, base_baud = 5000000) is a IMX
  169. console [ttymxc0] enabled
  170. 21e8000.serial: ttymxc1 at MMIO 0x21e8000 (irq = 59, base_baud = 5000000) is a IMX
  171. 21ec000.serial: ttymxc2 at MMIO 0x21ec000 (irq = 60, base_baud = 5000000) is a IMX
  172. [drm] Initialized drm 1.1.0 20060810
  173. [drm] Initialized vivante 1.0.0 20120216 on minor 0
  174. brd: module loaded
  175. loop: module loaded
  176. nand: device found, Manufacturer ID: 0xec, Chip ID: 0xf1
  177. nand: Samsung NAND 128MiB 3,3V 8-bit
  178. nand: 128MiB, SLC, page size: 2048, OOB size: 64
  179. Bad block table found at page 65472, version 0x01
  180. Bad block table found at page 65408, version 0x01
  181. 6 cmdlinepart partitions found on MTD device gpmi-nand
  182. Creating 6 MTD partitions on "gpmi-nand":
  183. 0x000000020000-0x000000120000 : "u-boot"
  184. 0x000000120000-0x000000180000 : "env"
  185. 0x000000180000-0x000000880000 : "linux"
  186. 0x000000880000-0x000007f60000 : "rootfs"
  187. 0x000007f60000-0x000007f80000 : "dtb"
  188. 0x000007f80000-0x000008000000 : "bbt"
  189. gpmi-nand 112000.gpmi-nand: driver registered.
  190. spi_imx 2008000.ecspi: probed
  191. vcan: Virtual CAN interface driver
  192. CAN device driver interface
  193. 2090000.flexcan supply xceiver not found, using dummy regulator
  194. flexcan 2090000.flexcan: device registered (reg_base=c09d0000, irq=142)
  195. 2094000.flexcan supply xceiver not found, using dummy regulator
  196. flexcan 2094000.flexcan: device registered (reg_base=c09d8000, irq=143)
  197. libphy: fec_enet_mii_bus: probed
  198. fec 2188000.ethernet eth0: registered PHC device 0
  199. ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
  200. ehci-pci: EHCI PCI platform driver
  201. usbcore: registered new interface driver usb-storage
  202. usbcore: registered new interface driver ums-datafab
  203. usbcore: registered new interface driver ums-realtek
  204. usbcore: registered new interface driver ums-sddr09
  205. usbcore: registered new interface driver ums-sddr55
  206. ci_hdrc ci_hdrc.1: EHCI Host Controller
  207. ci_hdrc ci_hdrc.1: new USB bus registered, assigned bus number 1
  208. ci_hdrc ci_hdrc.1: USB 2.0 started, EHCI 1.00
  209. usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
  210. usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
  211. usb usb1: Product: EHCI Host Controller
  212. usb usb1: Manufacturer: Linux 3.16.0-00787-g1fb9d67 ehci_hcd
  213. usb usb1: SerialNumber: ci_hdrc.1
  214. hub 1-0:1.0: USB hub found
  215. hub 1-0:1.0: 1 port detected
  216. input: 20b8000.kpp as /devices/soc0/soc/2000000.aips-bus/20b8000.kpp/input/input0
  217. usbcore: registered new interface driver usbtouchscreen
  218. input: TSC2007 Touchscreen as /devices/soc0/soc/2100000.aips-bus/21a8000.i2c/i2c-2/2-0048/input/input1
  219. rtc-ds1307 0-0068: rtc core: registered ds1339 as rtc0
  220. snvs_rtc 20cc034.snvs-rtc-lp: rtc core: registered 20cc034.snvs-rtc-lp as rtc1
  221. i2c /dev entries driver
  222. mxc_v4l2_output v4l2_out: V4L2 device registered as video16
  223. mxc_v4l2_output v4l2_out: V4L2 device registered as video17
  224. imx2-wdt 20bc000.wdog: timeout 60 sec (nowayout=0)
  225. sdhci: Secure Digital Host Controller Interface driver
  226. sdhci: Copyright(c) Pierre Ossman
  227. sdhci-pltfm: SDHCI platform and OF driver helper
  228. mmc0: no vqmmc regulator found
  229. mmc0: no vmmc regulator found
  230. mmc0: SDHCI controller on 2190000.usdhc [2190000.usdhc] using ADMA
  231. mmc1: no vqmmc regulator found
  232. mmc1: no vmmc regulator found
  233. mmc1: SDHCI controller on 2194000.usdhc [2194000.usdhc] using ADMA
  234. galcore: clk_get vg clock failed, disable vg!
  235. Galcore version 5.0.11.25762
  236. mxc_vpu 2040000.vpu: VPU initialized
  237. usbcore: registered new interface driver usbhid
  238. usbhid: USB HID core driver
  239. sgtl5000 2-000a: sgtl5000 revision 0x11
  240. 2-000a: 1200 mV normal
  241. sgtl5000 2-000a: Using internal LDO instead of VDDD
  242. imx-sgtl5000 sound: sgtl5000 <-> 2028000.ssi mapping ok
  243. TCP: cubic registered
  244. NET: Registered protocol family 17
  245. can: controller area network core (rev 20120528 abi 9)
  246. NET: Registered protocol family 29
  247. can: raw protocol (rev 20120528)
  248. can: broadcast manager protocol (rev 20120528 t)
  249. Key type dns_resolver registered
  250. failed to disable 1.2 GHz OPP
  251. Registering SWP/SWPB emulation handler
  252. UBI: default fastmap pool size: 45
  253. UBI: default fastmap WL pool size: 25
  254. UBI: attaching mtd3 to ubi0
  255. UBI: scanning is finished
  256. UBI: attached mtd3 (name "rootfs", size 118 MiB) to ubi0
  257. UBI: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
  258. UBI: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
  259. UBI: VID header offset: 2048 (aligned 2048), data offset: 4096
  260. UBI: good PEBs: 951, bad PEBs: 0, corrupted PEBs: 0
  261. UBI: user volume: 1, internal volumes: 1, max. volumes count: 128
  262. UBI: max/mean erase counter: 2/0, WL threshold: 4096, image sequence number: 1784703008
  263. UBI: available PEBs: 0, total reserved PEBs: 951, PEBs reserved for bad PEB handling: 20
  264. UBI: background thread "ubi_bgt0d" started, PID 95
  265. input: gpio-keys as /devices/soc0/gpio-keys/input/input2
  266. random: nonblocking pool is initialized
  267. rtc-ds1307 0-0068: setting system clock to 2015-05-04 04:54:05 UTC (1430715245)
  268. ALSA device list:
  269. #0: sgtl5000-audio
  270. UBIFS: parse sync
  271. UBIFS: background thread "ubifs_bgt0_0" started, PID 96
  272. UBIFS: recovery needed
  273. UBI error: __wl_get_peb: no free eraseblocks
  274. UBIFS: recovery completed
  275. UBIFS: mounted UBI device 0, volume 0, name "rootfs"
  276. UBIFS: LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
  277. UBIFS: FS size: 116056064 bytes (110 MiB, 914 LEBs), journal size 9023488 bytes (8 MiB, 72 LEBs)
  278. UBIFS: reserved for root: 0 bytes (0 KiB)
  279. UBIFS: media format: w4/r0 (latest is w4/r0), UUID 8281AE5E-F936-4B86-AF32-36D197330B9A, small LPT model
  280. VFS: Mounted root (ubifs filesystem) on device 0:13.
  281. devtmpfs: mounted
  282. Freeing unused kernel memory: 232K (80807000 - 80841000)
  283. Failed to execute /linuxrc (error -2). Attempting defaults...
  284. INIT: version 2.88 booting
  285. Starting udev
  286. udevd[121]: starting version 182
  287. UBI error: ubi_open_volume: cannot open device 0, volume 0, error -16
  288. INIT: Entering runlevel: 5
  289. Configuring network interfaces... fec 2188000.ethernet eth0: Freescale FEC PHY driver [SMSC LAN8710/LAN8720] (mii_bus:phy_addr=2188000.ethernet:00, irq=-1)
  290. udhcpc (v1.22.1) started
  291. Sending discover...
  292. fec 2188000.ethernet eth0: Link is Up - 100Mbps/Full - flow control rx/tx
  293. Sending discover...
  294. Sending select for 10.1.1.97...
  295. Lease of 10.1.1.97 obtained, lease time 691200
  296. /etc/udhcpc.d/50default: Adding DNS 10.1.1.1
  297. done.
  298. Starting system message bus: dbus.
  299. Starting OpenBSD Secure Shell server: sshd
  300. done.
  301. Starting rpcbind daemon...rpcbind: cannot create socket for udp6
  302. rpcbind: cannot create socket for tcp6
  303. done.
  304. starting statd: done
  305. modprobe: can't change directory to '3.16.0-00787-g1fb9d67': No such file or directory
  306. NFS daemon support not enabled in kernel
  307. Starting ntpd: done
  308. Starting ftp server proftpd... done.
  309. Starting syslogd/klogd: done
  310. Running local boot scripts (/etc/rc.local).
  311.  
  312. Poky (Yocto Project Reference Distro) 1.7.2 imx6qsabresd /dev/ttymxc0
  313.  
  314. imx6qsabresd login:
Advertisement
Add Comment
Please, Sign In to add comment
Advertisement
Public Pastes
Advertisement
We use cookies for various purposes including analytics. By continuing to use Pastebin, you agree to our use of cookies as described in the Cookies Policy.  OK, I Understand
Not a member of Pastebin yet?
Sign Up, it unlocks many cool features!