API tools faq
paste
Advertisement
Guest User

TP-Link_TL-WR710N_openwrt-bootlog.txt

a guest
Jul 1st, 2014
744
0
Never
Add comment
Not a member of Pastebin yet? Sign Up, it unlocks many cool features!
text 10.55 KB | None | 0 0
raw download clone embed print report
  1.  
  2. U-Boot 1.1.4 (Apr 19 2013 - 15:56:20)
  3.  
  4. AP121 (ar9330) U-boot
  5.  
  6. DRAM: 32 MB
  7. led turning on for 1s...
  8. id read 0x100000ff
  9. flash size 8388608, sector count = 128
  10. Flash: 8 MB
  11. Using default environment
  12.  
  13. In: serial
  14. Out: serial
  15. Err: serial
  16. Net: ag7240_enet_initialize...
  17. No valid address in Flash. Using fixed address
  18. No valid address in Flash. Using fixed address
  19. : cfg1 0x5 cfg2 0x7114
  20. eth0: 00:03:7f:ab:cd:ef
  21. ag7240_phy_setup
  22. eth0 up
  23. : cfg1 0xf cfg2 0x7214
  24. eth1: 00:03:7f:ab:cd:ef
  25. athrs26_reg_init_lan
  26. ATHRS26: resetting s26
  27. ATHRS26: s26 reset done
  28. ag7240_phy_setup
  29. eth1 up
  30. eth0, eth1
  31. Autobooting in 1 seconds
  32. ## Booting image at 9f020000 ...
  33. Uncompressing Kernel Image ... OK
  34.  
  35. Starting kernel ...
  36.  
  37. [ 0.000000] Linux version 3.10.44 (openwrt@gb-14) (gcc version 4.8.3 (OpenWrt/Linaro GCC 4.8-2014.04 r41391) ) #1 Mon Jun 30 05:39:05 UTC 2014
  38. [ 0.000000] bootconsole [early0] enabled
  39. [ 0.000000] CPU revision is: 00019374 (MIPS 24Kc)
  40. [ 0.000000] SoC: Atheros AR9330 rev 1
  41. [ 0.000000] Clocks: CPU:400.000MHz, DDR:400.000MHz, AHB:200.000MHz, Ref:25.000MHz
  42. [ 0.000000] Determined physical RAM map:
  43. [ 0.000000] memory: 02000000 @ 00000000 (usable)
  44. [ 0.000000] Initrd not found or empty - disabling initrd
  45. [ 0.000000] Zone ranges:
  46. [ 0.000000] Normal [mem 0x00000000-0x01ffffff]
  47. [ 0.000000] Movable zone start for each node
  48. [ 0.000000] Early memory node ranges
  49. [ 0.000000] node 0: [mem 0x00000000-0x01ffffff]
  50. [ 0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
  51. [ 0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
  52. [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 8128
  53. [ 0.000000] Kernel command line: board=TL-WR710N console=ttyATH0,115200 rootfstype=squashfs,jffs2 noinitrd
  54. [ 0.000000] PID hash table entries: 128 (order: -3, 512 bytes)
  55. [ 0.000000] Dentry cache hash table entries: 4096 (order: 2, 16384 bytes)
  56. [ 0.000000] Inode-cache hash table entries: 2048 (order: 1, 8192 bytes)
  57. [ 0.000000] Writing ErrCtl register=00000000
  58. [ 0.000000] Readback ErrCtl register=00000000
  59. [ 0.000000] Memory: 28588k/32768k available (2384k kernel code, 4180k reserved, 622k data, 256k init, 0k highmem)
  60. [ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
  61. [ 0.000000] NR_IRQS:51
  62. [ 0.000000] Calibrating delay loop... 265.42 BogoMIPS (lpj=1327104)
  63. [ 0.080000] pid_max: default: 32768 minimum: 301
  64. [ 0.080000] Mount-cache hash table entries: 512
  65. [ 0.090000] NET: Registered protocol family 16
  66. [ 0.100000] MIPS: machine is TP-LINK TL-WR710N v1
  67. [ 0.550000] bio: create slab <bio-0> at 0
  68. [ 0.560000] Switching to clocksource MIPS
  69. [ 0.560000] NET: Registered protocol family 2
  70. [ 0.570000] TCP established hash table entries: 512 (order: 0, 4096 bytes)
  71. [ 0.570000] TCP bind hash table entries: 512 (order: -1, 2048 bytes)
  72. [ 0.570000] TCP: Hash tables configured (established 512 bind 512)
  73. [ 0.580000] TCP: reno registered
  74. [ 0.580000] UDP hash table entries: 256 (order: 0, 4096 bytes)
  75. [ 0.590000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
  76. [ 0.600000] NET: Registered protocol family 1
  77. [ 0.620000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
  78. [ 0.620000] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
  79. [ 0.630000] msgmni has been set to 55
  80. [ 0.640000] io scheduler noop registered
  81. [ 0.640000] io scheduler deadline registered (default)
  82. [ 0.650000] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled
  83. [ 0.660000] ar933x-uart: ttyATH0 at MMIO 0x18020000 (irq = 11) is a AR933X UART
  84. [ 0.670000] console [ttyATH0] enabled, bootconsole disabled
  85. [ 0.670000] console [ttyATH0] enabled, bootconsole disabled
  86. [ 0.680000] ath79-spi ath79-spi: master is unqueued, this is deprecated
  87. [ 0.690000] m25p80 spi0.0: found s25fl064k, expected m25p80
  88. [ 0.690000] m25p80 spi0.0: s25fl064k (8192 Kbytes)
  89. [ 0.700000] 5 tp-link partitions found on MTD device spi0.0
  90. [ 0.700000] Creating 5 MTD partitions on "spi0.0":
  91. [ 0.710000] 0x000000000000-0x000000020000 : "u-boot"
  92. [ 0.710000] 0x000000020000-0x00000012c460 : "kernel"
  93. [ 0.720000] mtd: partition "kernel" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
  94. [ 0.730000] 0x00000012c460-0x0000007f0000 : "rootfs"
  95. [ 0.730000] mtd: partition "rootfs" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
  96. [ 0.750000] mtd: device 2 (rootfs) set to be root filesystem
  97. [ 0.750000] 1 squashfs-split partitions found on MTD device rootfs
  98. [ 0.760000] 0x000000300000-0x0000007f0000 : "rootfs_data"
  99. [ 0.770000] 0x0000007f0000-0x000000800000 : "art"
  100. [ 0.770000] 0x000000020000-0x0000007f0000 : "firmware"
  101. [ 0.790000] libphy: ag71xx_mdio: probed
  102. [ 1.340000] ag71xx ag71xx.0: connected to PHY at ag71xx-mdio.1:04 [uid=004dd041, driver=Generic PHY]
  103. [ 1.350000] eth0: Atheros AG71xx at 0xb9000000, irq 4, mode:MII
  104. [ 1.910000] ag71xx-mdio.1: Found an AR7240/AR9330 built-in switch
  105. [ 2.940000] eth1: Atheros AG71xx at 0xba000000, irq 5, mode:GMII
  106. [ 2.940000] TCP: cubic registered
  107. [ 2.950000] NET: Registered protocol family 17
  108. [ 2.950000] Bridge firewalling registered
  109. [ 2.950000] 8021q: 802.1Q VLAN Support v1.8
  110. [ 2.970000] VFS: Mounted root (squashfs filesystem) readonly on device 31:2.
  111. [ 2.970000] Freeing unused kernel memory: 256K (80350000 - 80390000)
  112. procd: Console is alive
  113. procd: - watchdog -
  114. [ 5.770000] usbcore: registered new interface driver usbfs
  115. [ 5.770000] usbcore: registered new interface driver hub
  116. [ 5.780000] usbcore: registered new device driver usb
  117. [ 5.790000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
  118. [ 5.800000] ehci-platform: EHCI generic platform driver
  119. [ 5.800000] ehci-platform ehci-platform: EHCI Host Controller
  120. [ 5.810000] ehci-platform ehci-platform: new USB bus registered, assigned bus number 1
  121. [ 5.820000] ehci-platform ehci-platform: irq 3, io mem 0x1b000000
  122. [ 5.840000] ehci-platform ehci-platform: USB 2.0 started, EHCI 1.00
  123. [ 5.840000] hub 1-0:1.0: USB hub found
  124. [ 5.840000] hub 1-0:1.0: 1 port detected
  125. [ 5.850000] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
  126. procd: - preinit -
  127. Press the [f] key and hit [enter] to enter failsafe mode
  128. Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level
  129. [ 8.010000] eth1: link up (1000Mbps/Full duplex)
  130. jffs2 is ready
  131. jffs2 is ready
  132. [ 10.730000] jffs2: notice: (332) jffs2_build_xattr_subsystem: complete building xattr subsystem, 1 of xdatum (0 unchecked, 0 orphan) and 14 of xref (0 dead, 2 orphan) found.
  133. switching to overlay
  134. [ 10.760000] eth1: link down
  135. procd: - early -
  136. procd: - watchdog -
  137. procd: - ubus -
  138. procd: - init -
  139. Please press Enter to activate this console.
  140. [ 12.370000] NET: Registered protocol family 10
  141. [ 12.390000] nf_conntrack version 0.5.0 (450 buckets, 1800 max)
  142. [ 12.400000] ip6_tables: (C) 2000-2006 Netfilter Core Team
  143. [ 12.420000] Loading modules backported from Linux version master-2014-05-22-0-gf2032ea
  144. [ 12.420000] Backport generated by backports.git backports-20140320-37-g5c33da0
  145. [ 12.430000] ip_tables: (C) 2000-2006 Netfilter Core Team
  146. [ 12.480000] xt_time: kernel timezone is -0000
  147. [ 12.520000] cfg80211: Calling CRDA to update world regulatory domain
  148. [ 12.520000] cfg80211: World regulatory domain updated:
  149. [ 12.530000] cfg80211: DFS Master region: unset
  150. [ 12.530000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time)
  151. [ 12.540000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
  152. [ 12.550000] cfg80211: (2457000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
  153. [ 12.560000] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (N/A, 2000 mBm), (N/A)
  154. [ 12.560000] cfg80211: (5170000 KHz - 5250000 KHz @ 80000 KHz), (N/A, 2000 mBm), (N/A)
  155. [ 12.570000] cfg80211: (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 2000 mBm), (N/A)
  156. [ 12.580000] cfg80211: (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 0 mBm), (N/A)
  157. [ 12.660000] PPP generic driver version 2.4.2
  158. [ 12.680000] NET: Registered protocol family 24
  159. [ 12.760000] cfg80211: Calling CRDA for country: US
  160. [ 12.770000] cfg80211: Regulatory domain changed to country: US
  161. [ 12.770000] cfg80211: DFS Master region: FCC
  162. [ 12.770000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time)
  163. [ 12.780000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 3000 mBm), (N/A)
  164. [ 12.790000] cfg80211: (5170000 KHz - 5250000 KHz @ 80000 KHz), (N/A, 1700 mBm), (N/A)
  165. [ 12.800000] cfg80211: (5250000 KHz - 5330000 KHz @ 80000 KHz), (N/A, 2300 mBm), (0 s)
  166. [ 12.810000] cfg80211: (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 3000 mBm), (N/A)
  167. [ 12.820000] cfg80211: (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 4000 mBm), (N/A)
  168. [ 12.820000] ieee80211 phy0: Atheros AR9330 Rev:1 mem=0xb8100000, irq=2
  169. procd: - init complete -
  170. [ 22.260000] IPv6: ADDRCONF(NETDEV_UP): eth1: link is not ready
  171. [ 22.260000] device eth1 entered promiscuous mode
  172. [ 22.270000] IPv6: ADDRCONF(NETDEV_UP): br-lan: link is not ready
  173. [ 22.290000] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
  174. [ 22.860000] eth1: link up (1000Mbps/Full duplex)
  175. [ 22.860000] br-lan: port 1(eth1) entered forwarding state
  176. [ 22.870000] br-lan: port 1(eth1) entered forwarding state
  177. [ 22.870000] IPv6: ADDRCONF(NETDEV_CHANGE): eth1: link becomes ready
  178. [ 22.890000] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready
  179. [ 24.870000] br-lan: port 1(eth1) entered forwarding state
  180.  
  181.  
  182.  
  183. BusyBox v1.22.1 (2014-06-30 05:25:35 UTC) built-in shell (ash)
  184. Enter 'help' for a list of built-in commands.
  185.  
  186. _______ ________ __
  187. | |.-----.-----.-----.| | | |.----.| |_
  188. | - || _ | -__| || | | || _|| _|
  189. |_______|| __|_____|__|__||________||__| |____|
  190. |__| W I R E L E S S F R E E D O M
  191. -----------------------------------------------------
  192. BARRIER BREAKER (Bleeding Edge, r41391)
  193. -----------------------------------------------------
  194. * 1/2 oz Galliano Pour all ingredients into
  195. * 4 oz cold Coffee an irish coffee mug filled
  196. * 1 1/2 oz Dark Rum with crushed ice. Stir.
  197. * 2 tsp. Creme de Cacao
  198. -----------------------------------------------------
  199. root@OpenWrt:/#
  200. root@OpenWrt:/#
Advertisement
Add Comment
Please, Sign In to add comment
Advertisement
Public Pastes
Advertisement
We use cookies for various purposes including analytics. By continuing to use Pastebin, you agree to our use of cookies as described in the Cookies Policy.  OK, I Understand
Not a member of Pastebin yet?
Sign Up, it unlocks many cool features!