Advertisement
Not a member of Pastebin yet?
Sign Up,
it unlocks many cool features!
- U-Boot 2012.07-svn13437 [Standard IPQ806X.LN,r40858] (Feb 04 2016 - 14:16:32)
- smem ram ptable found: ver: 0 len: 5
- DRAM: 491 MiB
- NAND: ipq_nand: unknown NAND device manufacturer: 0 device: 0
- ipq_nand: failed to identify device
- SF: we have a match, call probe
- SF: Detected W25Q128 with page size 64 KiB, total 16 MiB
- ipq_spi: page_size: 0x100, sector_size: 0x10000, size: 0x1000000
- 16 MiB
- MMC:
- *** Warning - bad CRC, using default environment
- PCI0 Link Intialized
- PCI1 Link Intialized
- In: serial
- Out: serial
- Err: serial
- Net: No ART partition found
- MAC1 addr:0:3:7f:ba:db:1
- S17c athrs17_init_switch done.
- WJL: athrs17_reg_init() reg-0x30=0x80000700.1.
- WJL: athrs17_reg_init() reg-0x30=0x80000401.2.
- WJL: athrs17_reg_init: PAD config after SOFT_RESET.
- WJL: athrs17_reg_init: 0x0000007c=0x00001080.1.
- WJL: athrs17_reg_init: 0x00000094=0x00001080.2.
- athrs17_reg_init: complete
- S17c init done (WJL-07-10-1829, uboot task - internal loopback)
- MAC2 addr:0:3:7f:ba:db:2
- eth0
- Warning: eth0 MAC addresses don't match:
- Address in SROM is 00:03:7f:ba:db:01
- Address in environment is 00:aa:bb:cc:dd:ee
- , eth1
- Hit any key to stop autoboot: 1 0
- MMC Device 0 not found
- MMC Device 0 not found
- Loading from nand1, offset 0x320200
- Image Name: Linux-3.4.103
- Image Type: ARM Linux Kernel Image (uncompressed)
- Data Size: 1884744 Bytes = 1.8 MiB
- Load Address: 41508000
- Entry Point: 41508000
- Automatic boot of image at addr 0x44000000 ...
- Image Name: Linux-3.4.103
- Image Type: ARM Linux Kernel Image (uncompressed)
- Data Size: 1884744 Bytes = 1.8 MiB
- Load Address: 41508000
- Entry Point: 41508000
- Verifying Checksum ... OK
- Loading Kernel Image ... OK
- OK
- device nand1 <nand1>, # parts = 1
- #: name size offset mask_flags
- 0: ART 0x00040000 0x00fc0000 0
- active partition: nand1,0 - (ART) 0x00040000 @ 0x00fc0000
- defaults:
- mtdids : none
- mtdparts: none
- Setting up atags for msm partition: ART
- Using machid 0x1260 from environment
- Starting kernel ...
- [ 0.000000] Booting Linux on physical CPU 0
- [ 0.000000] Linux version 3.4.103 (root@localhost.localdomain) (gcc version 4.6.3 20120201 (prerelease) (Linaro GCC 4.6-2012.02) ) #329 SMP PREEMPT Thu Feb 4 14:45:57 HKT 2016
- [ 0.000000] CPU: ARMv7 Processor [512f04d0] revision 0 (ARMv7), cr=10c5387d
- [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, PIPT instruction cache
- [ 0.000000] Machine: Qualcomm Atheros AP148 reference board
- [ 0.000000] Partition (from atag) ART -- Offset:fc Size:4
- [ 0.000000] msm_reserve_memory: 0x44000000, 0x600000
- [ 0.000000] msm_reserve_memory: 0x44600000, 0x200000
- [ 0.000000] memory pool 3 (start 5fc00000 size 400000) initialized
- [ 0.000000] Memory policy: ECC disabled, Data cache writealloc
- [ 0.000000] smem_find(137, 80): wrong size 72
- [ 0.000000] socinfo_init: v6, id=202, ver=2.0, raw_id=2064, raw_ver=2064, hw_plat=0, hw_plat_ver=65536
- [ 0.000000] accessory_chip=0 hw_plat_subtype=0
- [ 0.000000] PERCPU: Embedded 8 pages/cpu @c0c7d000 s10816 r8192 d13760 u32768
- [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 121642
- [ 0.000000] Kernel command line: console=ttyHSL1,115200n8 root=mtd:rootfs rootfstype=squashfs
- [ 0.000000] PID hash table entries: 2048 (order: 1, 8192 bytes)
- [ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
- [ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
- [ 0.000000] Memory: 43MB 436MB = 479MB total
- [ 0.000000] Memory: 477212k/489500k available, 13284k reserved, 0K highmem
- [ 0.000000] Virtual kernel memory layout:
- [ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB)
- [ 0.000000] fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB)
- [ 0.000000] vmalloc : 0xdf000000 - 0xff000000 ( 512 MB)
- [ 0.000000] lowmem : 0xc0000000 - 0xdeb00000 ( 491 MB)
- [ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB)
- [ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB)
- [ 0.000000] .text : 0xc0008000 - 0xc051c000 (5200 kB)
- [ 0.000000] .init : 0xc0600000 - 0xc0702a40 (1035 kB)
- [ 0.000000] .data : 0xc0704000 - 0xc07a5e48 ( 648 kB)
- [ 0.000000] .bss : 0xc07a5e6c - 0xc08790d0 ( 845 kB)
- [ 0.000000] SLUB: Genslabs=11, HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
- [ 0.000000] Preemptible hierarchical RCU implementation.
- [ 0.000000] NR_IRQS:1689
- [ 0.000000] sched_clock: 32 bits at 32kHz, resolution 31240ns, wraps every 134175798ms
- [ 0.000000] Console: colour dummy device 80x30
- [ 0.150452] Calibrating delay using timer specific routine.. 12.55 BogoMIPS (lpj=62799)
- [ 0.150484] pid_max: default: 32768 minimum: 301
- [ 0.150921] Mount-cache hash table entries: 512
- [ 0.152389] CPU: Testing write buffer coherency: ok
- [ 0.152608] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
- [ 0.152639] hw perfevents: enabled with ARMv7 Krait PMU driver, 5 counters available
- [ 0.152733] Setting up static identity map for 0x418a61f8 - 0x418a6280
- [ 0.155014] CPU1: Booted secondary processor
- [ 0.155107] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001
- [ 0.155201] Brought up 2 CPUs
- [ 0.155201] SMP: Total of 2 processors activated (25.11 BogoMIPS).
- [ 0.171727] dummy:
- [ 0.172414] NET: Registered protocol family 16
- [ 0.173195] AXI: msm_bus_fabric_init_driver(): msm_bus_fabric_init_driver
- [ 0.175507] meminfo_init: smem ram ptable found: ver: 0 len: 5
- [ 0.175538] Found 1 memory banks grouped into 8 memory regions
- [ 0.175820] gpiochip_add: registered GPIOs 0 to 151 on device: msmgpio
- [ 0.176632] smem_find(137, 80): wrong size 72
- [ 0.176663] socinfo_init: v6, id=202, ver=2.0, raw_id=2064, raw_ver=2064, hw_plat=0, hw_plat_ver=65536
- [ 0.176663] accessory_chip=0 hw_plat_subtype=0
- [ 0.176694] msm_rpm_init: RPM firmware 3.0.16777342
- [ 0.184442] clk_tbl_nss - loaded
- [ 0.211558] hw-breakpoint: found 5 (+1 reserved) breakpoint and 4 watchpoint registers.
- [ 0.211558] hw-breakpoint: maximum watchpoint size is 8 bytes.
- [ 0.211965] msm_dmov_memcpy_init: Success
- [ 0.219587] sps:BAM 0x12244000 enabled: ver:0x5, number of pipes:20
- [ 0.219618] sps:BAM 0x12244000 is registered.
- [ 0.219868] sps:sps is ready.
- [ 0.260918] msm_pcie_setup: link initialized
- [ 0.261324] PCI host bridge to bus 0000:00
- [ 0.261324] pci_bus 0000:00: root bus resource [mem 0x08000000-0x0fefffff]
- [ 0.261855] PCI: bus0: Fast back to back transfers disabled
- [ 0.261855] pci 0000:00:00.0: bridge configuration invalid ([bus 00-00]), reconfiguring
- [ 0.262699] PCI: bus1: Fast back to back transfers disabled
- [ 0.301030] msm_pcie_setup: link initialized
- [ 0.301405] PCI host bridge to bus 0000:02
- [ 0.301405] pci_bus 0000:02: root bus resource [mem 0x2e000000-0x31efffff]
- [ 0.301874] PCI: bus2: Fast back to back transfers disabled
- [ 0.301905] pci 0000:02:00.0: bridge configuration invalid ([bus 00-00]), reconfiguring
- [ 0.302624] PCI: bus3: Fast back to back transfers disabled
- [ 0.421368] msm_pcie_setup: link initialization failed
- [ 0.421587] pci 0000:02:00.0: BAR 8: assigned [mem 0x2e000000-0x2e1fffff]
- [ 0.421618] pci 0000:03:00.0: BAR 0: assigned [mem 0x2e000000-0x2e1fffff 64bit]
- [ 0.421649] pci 0000:02:00.0: PCI bridge to [bus 03-03]
- [ 0.421680] pci 0000:02:00.0: bridge window [mem 0x2e000000-0x2e1fffff]
- [ 0.421743] PCI: enabling device 0000:02:00.0 (0140 -> 0143)
- [ 0.421805] pci 0000:00:00.0: BAR 8: assigned [mem 0x08000000-0x081fffff]
- [ 0.421805] pci 0000:01:00.0: BAR 0: assigned [mem 0x08000000-0x081fffff 64bit]
- [ 0.421868] pci 0000:00:00.0: PCI bridge to [bus 01-01]
- [ 0.421899] pci 0000:00:00.0: bridge window [mem 0x08000000-0x081fffff]
- [ 0.421930] PCI: enabling device 0000:00:00.0 (0140 -> 0143)
- [ 0.445454] bio: create slab <bio-0> at 0
- [ 0.447422] SCSI subsystem initialized
- [ 0.449265] spi_qsd spi_qsd.5: master is unqueued, this is deprecated
- [ 0.451733] spi_qsd spi_qsd.6: master is unqueued, this is deprecated
- [ 0.455607] Switching to clocksource gp_timer
- [ 0.477413] NET: Registered protocol family 2
- [ 0.487129] IP route cache hash table entries: 4096 (order: 2, 16384 bytes)
- [ 0.487753] TCP established hash table entries: 16384 (order: 5, 131072 bytes)
- [ 0.487941] TCP bind hash table entries: 16384 (order: 5, 131072 bytes)
- [ 0.488128] TCP: Hash tables configured (established 16384 bind 16384)
- [ 0.488159] TCP: reno registered
- [ 0.488159] UDP hash table entries: 256 (order: 1, 8192 bytes)
- [ 0.488191] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
- [ 0.488628] NET: Registered protocol family 1
- [ 0.489971] Detected 5 counters on the L2CC PMU.
- [ 0.491002] smd: register irq failed on wcnss_a11
- [ 0.491034] smd: deregistering IRQs
- [ 0.491065] SMD: smd_core_platform_init() failed
- [ 0.491815] Partition(from smem) SBL1 -- Offset:0 Size:20000
- [ 0.491846] Partition(from smem) MIBIB -- Offset:20000 Size:20000
- [ 0.491846] Partition(from smem) SBL2 -- Offset:40000 Size:40000
- [ 0.491877] Partition(from smem) SBL3 -- Offset:80000 Size:80000
- [ 0.491877] Partition(from smem) DDRCONFIG -- Offset:100000 Size:10000
- [ 0.491908] Partition(from smem) SSD -- Offset:110000 Size:10000
- [ 0.491908] Partition(from smem) TZ -- Offset:120000 Size:80000
- [ 0.491940] Partition(from smem) RPM -- Offset:1a0000 Size:80000
- [ 0.491971] Partition(from smem) APPSBL -- Offset:220000 Size:80000
- [ 0.491971] Partition(from smem) APPSBLENV -- Offset:2a0000 Size:40000
- [ 0.492002] Partition(from smem) kernel -- Offset:320000 Size:200000
- [ 0.492033] Partition(from smem) rootfs -- Offset:520000 Size:a60000
- [ 0.492033] get_bootconfig_partition: magic not found
- [ 0.507154] acpuclk-ipq806x acpuclk-ipq806x: SPEED BIN: 0
- [ 0.507154] acpuclk-ipq806x acpuclk-ipq806x: ACPU PVS: 1
- [ 0.513776] acpuclk-ipq806x acpuclk-ipq806x: CPU0: 6 frequencies supported
- [ 0.513808] acpuclk-ipq806x acpuclk-ipq806x: CPU1: 6 frequencies supported
- [ 0.515338] msm_rpm_log_probe: OK
- [ 0.533801] squashfs: version 4.0 (2009/01/31) Phillip Lougher
- [ 0.534864] fuse init (API version 7.18)
- [ 0.536144] msgmni has been set to 932
- [ 0.538206] io scheduler noop registered
- [ 0.538206] io scheduler deadline registered (default)
- [ 0.540018] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
- [ 0.543392] msm_serial_hs.0: ttyHS0 at MMIO 0x12490000 (irq = 227) is a MSM HS UART
- [ 0.544048] msm_serial_hs module loaded
- [ 0.544236] msm_serial_hsl: detected port #1
- [ 0.544361] msm_serial_hsl.1: ttyHSL1 at MMIO 0x16340000 (irq = 184) is a MSM
- [ 0.544798] msm_serial_hsl: console setup on port #1
- [ 1.315432] console [ttyHSL1] enabled
- [ 1.319587] msm_serial_hsl: driver initialized
- [ 1.341049] brd: module loaded
- [ 1.350984] loop: module loaded
- [ 1.357731] ahci ahci.0: forcing PORTS_IMPL to 0x1
- [ 1.361543] ahci ahci.0: AHCI 0001.0300 32 slots 1 ports 6 Gbps 0x1 impl platform mode
- [ 1.369447] ahci ahci.0: flags: ncq sntf pm led clo only pmp pio slum part ccc apst
- [ 1.378600] scsi0 : ahci_platform
- [ 1.381568] ata1: SATA max UDMA/133 mmio [mem 0x29000000-0x2900017f] port 0x100 irq 241
- [ 1.391565] Register flash device: flash0, major=200
- [ 1.397656] m25p80 spi5.0: found w25q128, expected s25fl512s
- [ 1.402280] m25p80 spi5.0: w25q128 (16384 Kbytes)
- [ 1.407653] Creating 13 MTD partitions on "m25p80":
- [ 1.411840] 0x000000fc0000-0x000001000000 : "ART"
- [ 1.418650] 0x000000000000-0x000000020000 : "SBL1"
- [ 1.424148] 0x000000020000-0x000000040000 : "MIBIB"
- [ 1.429803] 0x000000040000-0x000000080000 : "SBL2"
- [ 1.435270] 0x000000080000-0x000000100000 : "SBL3"
- [ 1.440830] 0x000000100000-0x000000110000 : "DDRCONFIG"
- [ 1.446797] 0x000000110000-0x000000120000 : "SSD"
- [ 1.452264] 0x000000120000-0x0000001a0000 : "TZ"
- [ 1.458044] 0x0000001a0000-0x000000220000 : "RPM"
- [ 1.464261] 0x000000220000-0x0000002a0000 : "APPSBL"
- [ 1.470790] 0x0000002a0000-0x0000002e0000 : "APPSBLENV"
- [ 1.477600] 0x000000320000-0x000000520000 : "kernel"
- [ 1.484067] 0x000000520000-0x000000f80000 : "rootfs"
- [ 1.490627] mtd: partition "rootfs" set to be root filesystem
- [ 1.495938] mtd: partition "rootfs_data" created automatically, ofs=EA0000, len=E0000
- [ 1.503248] 0x000000ea0000-0x000000f80000 : "rootfs_data"
- [ 1.511340] bonding: Ethernet Channel Bonding Driver: v3.7.1 (April 27, 2011)
- [ 1.562699] GPIO Bitbanged MDIO: probed
- [ 1.566198] PPP generic driver version 2.4.2
- [ 1.570384] NET: Registered protocol family 24
- [ 1.575476] ipq-dwc3 ipq-dwc3.0: unable to read platform data num of dbm eps
- [ 1.684879] ipq-dwc3 ipq-dwc3.1: unable to read platform data num of dbm eps
- [ 1.735707] ata1: SATA link down (SStatus 0 SControl 300)
- [ 1.804686] cpuidle: using governor ladder
- [ 1.807841] cpuidle: using governor menu
- [ 1.816963] Mirror/redirect action on
- [ 1.819587] u32 classifier
- [ 1.822274] Actions configured
- [ 1.825741] Netfilter messages via NETLINK v0.30.
- [ 1.830396] nf_conntrack version 0.5.0 (7456 buckets, 51200 max)
- [ 1.837675] ctnetlink v0.93: registering with nfnetlink.
- [ 1.842767] ip_tables: (C) 2000-2006 Netfilter Core Team
- [ 1.848109] TCP: cubic registered
- [ 1.852389] NET: Registered protocol family 10
- [ 1.858606] ip6_tables: (C) 2000-2006 Netfilter Core Team
- [ 1.863323] IPv6 over IPv4 tunneling driver
- [ 1.870977] NET: Registered protocol family 17
- [ 1.874476] NET: Registered protocol family 15
- [ 1.879162] Bridge firewalling registered
- [ 1.882849] Ebtables v2.0 registered
- [ 1.886504] 8021q: 802.1Q VLAN Support v1.8
- [ 1.890690] VFP support v0.3: implementor 51 architecture 64 part 4d variant 2 rev 0
- [ 1.898562] Registering SWP/SWPB emulation handler
- [ 1.903030] clock_late_init: Removing enables held for handed-off clocks
- [ 1.918338] ipq_nss_get_mac_addr: MAC[0]: ff:ff:ff:ff:ff:ff
- [ 1.922992] ipq_nss_get_mac_addr: MAC[1]: ff:ff:ff:ff:ff:ff
- [ 1.928709] ipq_nss_get_mac_addr: MAC[3]: ff:ff:ff:ff:ff:ff
- [ 1.934176] no pmic restart interrupt specified
- [ 1.940143] msm_cache_dump_probe: could not register L2 buffer ret = -22.
- [ 1.947766] input: gpio-keys as /devices/platform/gpio-keys/input/\FF[ 1.963636] VFS: Mounted root (squashfs filesystem) readonly on device 31:12.
- [ 1.970384] Freeing init memory: 1032K
- starting pid 826, tty '': '/etc/init.d/rcS'
- [ 3.400968] ssdk_plat_init start
- [ 3.508497] Register QCA PHY driver
- [ 3.746610] qca-ssdk module init succeeded!
- [ 3.911496] **********************************************************
- [ 3.916838] * Driver :NSS GMAC Driver for RTL v(3.72a)
- [ 3.922180] * Version :1.0
- [ 3.925054] * Copyright :Copyright (c) 2013-2014 The Linux Foundation. All rights reserved.
- [ 3.933395] **********************************************************mdio bus 'gpio-0' OK.
- [ 6.475070] Initialized NSS GMAC2 interface eth0: (base = 0x37400000, irq = 258, PhyId = 0, PollLink = 0)
- [ 6.483723] mdio bus 'gpio-0' OK.
- [ 6.486879] GMAC1(de1d64c0) Invalid MAC@ - using 1e:1f:20:21:22:23PHY gpio-0:04 attach OK
- [ 6.509497] nss_gmac_probe: Program RGMII Tx delay.....
- [ 6.515276] eth%d MII_PHYSID1 - 0x004d
- [ 6.518213] eth%d MII_PHYSID2 - 0xd036
- [ 6.524336] Initialized NSS GMAC1 interface eth1: (base = 0x37200000, irq = 255, PhyId = 4, PollLink = 1)
- [ 6.534645] mdio bus 'gpio-0' OK.
- [ 6.536925] GMAC0(de1d7cc0) Invalid MAC@ - using 8e:8f:90:91:92:93Initialized NSS GMAC0 interface eth2: (base = 0x37000000, irq = 252, PhyId = 32, PollLink = 0)
- [ 6.975413] nss_driver - fw of size 354304 bytes copied to load addr: 40000000, nss_id : 0
- [ 7.005185] nss_driver - Turbo Support 1
- [ 7.013120] bf0f72ed: NSS Shaping is enabled, handler id: 0
- [ 7.053639] nss_driver - fw of size 5392 bytes copied to load addr: 40800000, nss_id : 1
- [ 7.074601] Error - Duplicate Interface CB Registered for interface 75
- [ 7.080131] Error - Duplicate Interface CB Registered for interface 78
- [ 7.102155] Enabling NSS RPS
- [ 7.128553] nss_macsec init success
- [ 7.281880] button_hotplug: module license 'unspecified' taints kernel.
- [ 7.287503] Disabling lock debugging due to kernel taint
- [ 7.295251] Button Hotplug driver version 0.4.1
- [ 7.565791] ECM init
- [ 7.587691] ECM init complete
- [ 7.829709] usbcore: registered new interface driver usbfs
- [ 7.835676] usbcore: registered new interface driver hub
- [ 7.842549] usbcore: registered new device driver usb
- [ 7.974945] xhci-hcd xhci-hcd.0: xHCI Host Controller
- [ 7.979037] xhci-hcd xhci-hcd.0: new USB bus registered, assigned bus number 1
- [ 7.986285] xhci-hcd xhci-hcd.0: irq 142, io mem 0x11000000
- [ 7.995657] hub 1-0:1.0: USB hub found
- [ 7.998375] hub 1-0:1.0: 1 port detected
- [ 8.002436] xhci-hcd xhci-hcd.0: xHCI Host Controller
- [ 8.007372] xhci-hcd xhci-hcd.0: new USB bus registered, assigned bus number 2
- [ 8.015182] hub 2-0:1.0: USB hub found
- [ 8.018275] hub 2-0:1.0: 1 port detected
- [ 8.022399] xhci-hcd xhci-hcd.1: xHCI Host Controller
- [ 8.027241] xhci-hcd xhci-hcd.1: new USB bus registered, assigned bus number 3
- [ 8.034489] xhci-hcd xhci-hcd.1: irq 237, io mem 0x10000000
- [ 8.040674] hub 3-0:1.0: USB hub found
- [ 8.043705] hub 3-0:1.0: 1 port detected
- [ 8.049671] xhci-hcd xhci-hcd.1: xHCI Host Controller
- [ 8.053701] xhci-hcd xhci-hcd.1: new USB bus registered, assigned bus number 4
- [ 8.061543] hub 4-0:1.0: USB hub found
- [ 8.064636] hub 4-0:1.0: 1 port detected
- [ 8.075538] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
- [ 8.081162] msm_hsusb_host msm_hsusb_host: unable to find transceiver
- [ 8.095313] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
- [ 8.203623] Initializing USB Mass Storage driver...
- [ 8.209528] usbcore: registered new interface driver usb-storage
- [ 8.214495] USB Mass Storage support registered.
- [ 8.489315] Tuxera NTFS driver 3015.1.29 [Flags: R/W MODULE].
- [ 8.635988] Tuxera FAT 12/16/32 driver version 3014.9.10 [Flags: R/W MODULE].
- [ 8.672352] Tuxera HFS+ driver 3014.7.28
- [ 8.800624] Tuxera exFAT driver version 3014.9.10 [Flags: R/W MODULE].
- [ 8.926398] dns_init
- [ 8.927553] domain_name:tplinkmodem.net
- /dev/mem opened.
- Memory mapped at address 0x401c5000.
- Value at address 0x801020 (0x401c5020): 0x1C0
- Written 0x1C0; readback 0x1C0
- /dev/mem opened.
- Memory mapped at address 0x40261000.
- Value at address 0x801420 (0x40261420): 0x3C3
- Written 0x3C3; readback 0x3C3
- Please press Enter to activate this console. [ dm_readFile ] 2042: can not open xml file /var/tmp/pc/reduced_data_model.xml!, about to open file /etc/reduced_data_model.xml
- /bin/sh: can't create /proc/tplink/eth_vlan: nonexistent directory
- ddns_ud> start enable = 0, server: , auth: , request
- SSDK Init OK!
- operate done.
- SSDK Init OK!
- operate done.
- SSDK Init OK!
- operate done.
- SSDK Init OK!
- operate done.
- SSDK Init OK!
- operate done.
- SSDK Init OK!
- operate done.
- SSDK Init OK!
- operate done.
- SSDK Init OK!
- operate done.
- SSDK Init OK!
- operate done.
- SSDK Init OK!
- operate done.
- SSDK Init OK!
- operate done.
- SSDK Init OK!
- operate done.
- SSDK Init OK!
- operate done.
- SSDK Init OK!
- operate done.
- SSDK Init OK!
- operate done.
- SSDK Init OK!
- operate done.
- SSDK Init OK!
- operate done.
- SSDK Init OK!
- operate done.
- SSDK Init OK!
- operate done.
- SSDK Init OK!
- operate done.
- SSDK Init OK!
- operate done.
- SSDK Init OK!
- operate done.
- SSDK Init OK!
- operate done.
- SSDK Init OK!
- operate done.
- SSDK Init OK!
- operate done.
- SSDK Init OK!
- operate done.
- SSDK Init OK!
- operate done.
- SSDK Init OK!
- operate done.
- SSDK Init OK!
- operate done.
- SSDK Init OK!
- operate done.
- SSDK Init OK!
- operate done.
- SSDK Init OK!
- operate done.
- SSDK Init OK!
- operate done.
- SSDK Init OK!
- operate done.
- SSDK Init OK!
- operate done.
- SSDK Init OK!
- operate done.
- SSDK Init OK!
- operate done.
- SSDK Init OK!
- operate done.
- SSDK Init OK!
- operate done.
- ioctl: No such device
- [ 14.024773] device eth0.2 entered promiscuous mode
- [ 14.028647] device eth0 entered promiscuous mode
- [ 14.033239] br0: port 1(eth0.2) entered forwarding state
- [ 14.038456] br0: port 1(eth0.2) entered forwarding state
- [ 14.051421] device eth0.3 entered promiscuous mode
- [ 14.055263] br0: port 2(eth0.3) entered forwarding state
- [ 14.060512] br0: port 2(eth0.3) entered forwarding state
- [ 14.073133] device eth0.4 entered promiscuous mode
- [ 14.077007] br0: port 3(eth0.4) entered forwarding state
- [ 14.082193] br0: port 3(eth0.4) entered forwarding state
- [ 14.094689] device eth0.5 entered promiscuous mode
- [ 14.098656] br0: port 4(eth0.5) entered forwarding state
- [ 14.103748] br0: port 4(eth0.5) entered forwarding state
- *********cal_data_2g*******
- 202f612a0000000016000000
- *********cal_data_end*******
- *********cal_data_5g*******
- 202ffd2d0000000000161616
- *********cal_data_end*******
- [ 14.665635] ath_hal: 0.9.17.1 (AR5416, AR9380, WRITE_EEPROM, 11D)
- [ 14.697375] ath_spectral: Version 2.0.0
- [ 14.697407] Copyright (c) 2005-2009 Atheros Communications, Inc. All Rights Reserved
- [ 14.707997] SPECTRAL module built on Nov 5 2015 15:58:04
- [ 14.718775] ath_tx99: Version 2.0
- [ 14.718775] Copyright (c) 2010 Atheros Communications, Inc, All Rights Reserved
- [ 14.732989] ath_dfs: Version 2.0.0
- [ 14.732989] Copyright (c) 2005-2006 Atheros Communications, Inc. All Rights Reserved
- [ 14.747828] ath_rate_atheros: Copyright (c) 2001-2005 Atheros Communications, Inc, All Rights Reserved
- [ 14.999500] ath_dev: Copyright (c) 2001-2007 Atheros Communications, Inc, All Rights Reserved
- [ 16.235895] ath_pci: (Atheros/multi-bss)
- [ 16.238894] ath_pci_probe
- [ 16.241487] PCI device id is 0040 :0040
- [ 16.245298] PCI: enabling device 0000:01:00.0 (0140 -> 0142)
- [ 16.251202] ath_pci 0000:01:00.0: ath DEBUG: sc=0xdd913a00
- [ 16.256419]
- [ 16.256419] ol_ath_pci_configure : num_desired MSI set to 0
- [ 16.263542]
- [ 16.263542] Using PCI Legacy Interrupt
- [ 16.268853] chip_id 9 chip_revision 1
- [ 16.273133]
- [ 16.273133] address 4008f8 data db6c7c30
- [ 16.279162]
- [ 16.279162] address 401e90 data db6c7c34
- [ 16.285754]
- [ 16.285754] address 401e94 data db6c7c38
- [ 16.292377]
- [ 16.292377] address 401eb0 data db6c7c3c
- [ 16.299000]
- [ 16.299000] address 400900 data db6c7c3c
- [ 16.305654]
- [ 16.305654] CLOCK PLL skipped
- [ 16.309215] HIF_PCIDeviceProbed: setting the target pll frac ffffffff intval ffffffff
- [ 16.317057] HIF_PCIDeviceProbed: no frac provided, skipping pre-configuring PLL
- [ 16.324336] HIF_PCIDeviceProbed: ar900b_20_targ_clk is not provided, skipping pre-configuring PLL
- [ 16.336394]
- [ 16.336394] address 4008cc data db6c7c3c
- [ 16.343017] __ol_ath_attach: ath_attach TODO
- [ 16.346266] __ol_ath_attach 1755 host_enable 0 nss_nwifi_offload 0
- [ 16.352421] __ol_ath_attach: dev name wifi0
- [ 16.356607] ol_ath_set_default_tgt_config : AC Minfree buffer allocation through module param (umac.ko)
- [ 16.365948] OL_ACBKMinfree : 0
- [ 16.369072] OL_ACBEMinfree : 0
- [ 16.372196] OL_ACVIMinfree : 0
- [ 16.375320] OL_ACVOMinfree : 0
- [ 16.378475] ol_ath_attach() BMI inited.
- [ 16.382411] ol_ath_attach() BMI Get Target Info.
- [ 16.386941] ol_ath_attach() TARGET TYPE: 9 Vers 0x1000000
- [ 16.392252]
- [ 16.392252] CE WAR Disabled
- [ 16.396751] NUM_DEV=1 FWMODE=0x2 FWSUBMODE=0x0 FWBR_BUF 0
- [ 16.402218] ol_ath_attach() configure Target .
- [ 16.406560]
- [ 16.406560] Target Version is 1000000
- [ 16.411621]
- [ 16.411621] Flash Download Address c0000
- [ 16.417275] ol_transfer_bin_file: flash data file defined
- [ 16.422649] Cal location [0]: 00000000
- [ 16.426460]
- [ 16.426460] Wifi0 Select OFFSET 1000
- [ 16.450421] qc98xx_verify_checksum: flash checksum passed: 0x2a61
- [ 16.455482] ol_transfer_bin_file 2935: Download Flash data len 12064
- [ 16.462074] Board extended Data download address: 0x0
- [ 16.487191]
- [ 16.487222] Board data initialized
- [ 16.491190] Flash download ADDRESS 0xc0000
- [ 16.495220]
- [ 16.495220] Selecting OTP binary for CHIP Version 1
- [ 16.576038]
- [ 16.576038] First OTP send param 8000
- [ 16.583536] ol_ath_download_firmware :First OTP download and Execute is good return param 38912
- [ 16.591408]
- [ 16.591408] ##Board Id 6
- [ 16.595376]
- [ 16.595376] ##CHIP Id 1
- [ 16.599437]
- [ 16.599437] BOARDDATA DOWNLOAD TO address c0000
- [ 16.837300] ol_transfer_bin_file: Board data file: AR900B/hw.2/boardData_AR900B_CUS240_2GMipiHigh_v2_006.bin ARXXXX v=0x1
- [ 16.863917] Board extended Data download address: 0x0
- [ 16.888409] ol_ath_download_firmware: Using 0x1234 for the remainder of init
- [ 16.894407]
- [ 16.894439] Selecting OTP binary for CHIP Version 1
- [ 16.949671]
- [ 16.949703] Second otp download Param 10000
- [ 16.965417] ol_ath_download_firmware : OTP download and Execute is good
- [ 16.971290]
- [ 16.971290] FIRMWARE : Beeliner CHIP Version 1
- [ 16.995470] ol_swap_seg_alloc: Successfully allocated memory for SWAP size=131072
- [ 17.022149] Swap: bytes_left to copy: fw:16; dma_page:24579
- [ 17.026710] Swap: wrong length read:0
- [ 17.030334] ol_swap_wlan_memory_expansion: Swap total_bytes copied: 106493 Target address 417968
- [ 17.039331] scn=d9f804c0 target_write_addr=417968 seg_info=de041f10
- [ 17.045704] ol_transfer_swap_struct:Code swap structure successfully downloaded for bin type =2
- [ 17.054389] bin_filename=AR900B/hw.2/athwlan.bin swap_filename=/lib/firmware/AR900B/hw.2/athwlan.codeswap.bin
- open DNS error: No such file or directory
- [ oal_sys_getOldTZInfo ] 394: Open TZ file error!
- [ 18.746266] ol_ath_attach() Download FW.
- [ 18.749297] ol_ath_attach() HT Create .
- [ 18.753077] ol_ath_attach() HIF Claim.
- [ 18.756919] ol_ath_attach() BMI Done.
- [ 18.760574] ol_ath_attach() WMI attached. wmi_handle da250000
- [ 18.766385] +HWT
- [ 18.771009] CE_recv_buf_enqueue 809 Populate last entry 512 for CE 5
- [ 18.776319] CE_recv_buf_enqueue 818 CE 5 wi 511 dest_ptr 0x5b346040 nbytes 0 recv_ctxt 0xda015480
- [ 18.785567] Target:db3c2000 HTC Service:0x0001, ULpipe:0 DLpipe:1 id:0 Ready
- [ 18.792221] -HWT
- [ 18.794033]
- [ 18.794033] <=== cfg max peer id 1056 ====>
- [ 18.799812] Target:db3c2000 HTC Service:0x0300, ULpipe:4 DLpipe:5 id:1 Ready
- [ 18.806779] HTC Service:0x0300 ep:1 TX flow control disabled
- [ 18.813933] CE_pkt_dl_len_set CE 4 Pkt download length 64
- [ 18.819556] ol_txrx_pdev_attach: 1424 tx desc's allocated ; range starts from d9ad0000
- [ 18.826866] Target:db3c2000 HTC Service:0x0100, ULpipe:3 DLpipe:2 id:2 Ready
- [ 18.833489] HTC Service:0x0100 ep:2 TX flow control disabled
- [ 18.839893] wmi_service_ready_event_rx: WMI UNIFIED SERVICE READY event
- [ 18.845860] num_rf_chain : 00000004
- [ 18.849328] ht_cap_info: : 0000085b
- [ 18.852827] vht_cap_info : 339b79b2
- [ 18.856294] vht_supp_mcs : 0000ffea
- [ 18.859762] ol_ath_service_ready_event: tt_support: 1
- [ 18.864792] Peer Caching Enabled ; num_peers = 528, num_active_peers = 66 num_tids = 132, num_vdevs = 16
- [ 18.874258] idx 0 req 1 num_units 0 num_unit_info 2 unit size 1208 actual units 529
- [ 18.882505] idx 1 req 2 num_units 1 num_unit_info 4 unit size 256 actual units 67
- [ 18.889784] idx 2 req 3 num_units 1 num_unit_info 4 unit size 1024 actual units 67
- [ 18.897500] idx 3 req 4 num_units 1 num_unit_info 4 unit size 4096 actual units 67
- [ 18.905342] idx 4 req 6 num_units 35 num_unit_info 0 unit size 3072 actual units 35
- [ 18.913058] idx 5 req 7 num_units 1 num_unit_info 0 unit size 6144 actual units 1
- [ 18.920649] idx 6 req 5 num_units 0 num_unit_info 2 unit size 2080 actual units 529
- [ 18.929084] chunk 0 len 639032 requested ,ptr 0x5a900000
- [ 18.933895] chunk 1 len 17152 requested ,ptr 0x5b740000
- [ 18.939300] chunk 2 len 68608 requested ,ptr 0x5a880000
- [ 18.944642] chunk 3 len 274432 requested ,ptr 0x5aa00000
- [ 18.950140] chunk 4 len 107520 requested ,ptr 0x5a8a0000
- [ 18.955607] chunk 5 len 6144 requested ,ptr 0x5cac2000
- [ 18.960918] chunk 6 len 1100320 requested ,ptr 0x5a400000
- [ 19.044204] wmi_ready_event_rx: WMI UNIFIED READY event
- [ 19.048609] ol_ath_connect_htc() WMI is ready
- [ 19.052920] ol_ath_set_host_app_area TODO
- [ 19.057013] target uses HTT version 2.1; host uses 2.1
- [ 19.066073] ol_ath_attach() connect HTC.
- [ 19.069040] ol_regdmn_start: reg-domain param: regdmn=0, countryName=, wModeSelect=FFFFFFFF, netBand=FFFFFFFF, extendedChanMode=0.
- [ 19.080787] ol_regdmn_init_channels: !avail mode 0x680c (0x2) flags 0x2150
- [ 19.087660] ol_regdmn_init_channels: !avail mode 0x680c (0x1) flags 0x140
- [ 19.094407] ol_regdmn_init_channels: !avail mode 0x680c (0x20) flags 0xd0
- [ 19.101249] ol_regdmn_init_channels: !avail mode 0x680c (0x40) flags 0x150
- [ 19.108059] ol_regdmn_init_channels: !avail mode 0x680c (0x1000) flags 0x10100
- [ 19.115245] ol_regdmn_init_channels: !avail mode 0x680c (0x8000) flags 0x20100
- [ 19.122461] ol_regdmn_init_channels: !avail mode 0x680c (0x10000) flags 0x40100
- [ 19.129740] ol_regdmn_init_channels: !avail mode 0x680c (0x20000) flags 0x100100
- [ 19.137144] ol_regdmn_init_channels: !avail mode 0x680c (0x40000) flags 0x200100
- [ 19.144486] ol_regdmn_init_channels: !avail mode 0x680c (0x80000) flags 0x400100
- [ 19.151890] ol_regdmn_init_channels: !avail mode 0x680c (0x100000) flags 0x800100
- [ 19.159418] ol_ath_phyerr_attach: called
- [ 19.163292] OL Resmgr Init-ed
- [ 19.166229] ieee80211_bsteering_attach: Band steering initialized
- [ 19.172258] ol_if_spectral_setup
- [ 19.175476] SPECTRAL : get_capability not registered
- [ 19.180443] HAL_CAP_PHYDIAG : Capable
- [ 19.184067] SPECTRAL : Need to fix the capablity check for RADAR (spectral_attach : 231)
- [ 19.192158] SPECTRAL : get_capability not registered
- [ 19.197157] HAL_CAP_RADAR : Capable
- [ 19.200718] SPECTRAL : Need to fix the capablity check for SPECTRAL
- [ 19.200718] (spectral_attach : 236)
- [ 19.210590] SPECTRAL : get_capability not registered
- [ 19.215495] HAL_CAP_SPECTRAL_SCAN : Capable
- [ 19.220868] SPECTRAL : get_tsf64 not registered
- [ 19.224367] spectral_init_netlink 65 NULL SKB
- [ 19.228709] Green-AP : Green-AP : Attached
- [ 19.228741]
- [ 19.234270] Green-AP : Attached
- [ 19.237394] rate power table override is only supported for AR98XX
- [ 19.243580] ol_ath_smart_ant_attach: Hardware doest not support Smart Antenna.
- [ 19.250796] ieee80211com_init_netlink: 3223: Wifipos 1st Netlink socket created:db5fd800
- [ 19.258887] ol_if_dfs_setup: called
- [ 19.262386] ol_if_dfs_attach: called; ptr=d9545984, radar_info=db6c7be0
- [ 19.269228] ol_ath_rtt_meas_report_attach: called
- [ 19.273820] ol_ath_attach() UMAC attach .
- [ 19.277819] ol_if_dfs_configure: called
- [ 19.281568] ol_if_dfs_configure: FCC domain
- [ 19.285754] ol_if_dfs_disable: called
- [ 19.289472] ol_ath_attach: Calling ol_if_dfs_configure
- [ 19.294501]
- [ 19.294501] BURSTING enabled by default
- [ 19.300031] osif_wrap_attach:400 osif wrap attached
- [ 19.304779] osif_wrap_devt_init:361 osif wrap dev table init done
- [ 19.310840] Wrap Attached: Wrap_com =db5fc800 ic->ic_wrap_com=db5fc800 &wrap_com->wc_devt=db5fc800
- [ 19.319962] __ol_ath_attach: init tx/rx TODO
- [ 19.324179] __ol_ath_attach: needed_headroom reservation 44
- [ 19.332646] ol_ath_thermal_mitigation_attach: ++
- [ 19.336269] ol_ath_thermal_mitigation_attach: --
- [ 19.340893] ath_pci_probe
- [ 19.343455] PCI device id is 0040 :0040
- [ 19.347297] PCI: enabling device 0000:03:00.0 (0140 -> 0142)
- [ 19.353077] ath_pci 0000:03:00.0: ath DEBUG: sc=0xdb5fdc00
- [ 19.358388]
- [ 19.358388] ol_ath_pci_configure : num_desired MSI set to 0
- [ 19.365510]
- [ 19.365510] Using PCI Legacy Interrupt
- [ 19.370852] chip_id 9 chip_revision 1
- [ 19.374757]
- [ 19.374757] address 4008f8 data db6c7c30
- [ 19.381193]
- [ 19.381193] address 401e90 data db6c7c34
- [ 19.387785]
- [ 19.387785] address 401e94 data db6c7c38
- [ 19.394376]
- [ 19.394376] address 401eb0 data db6c7c3c
- [ 19.400968]
- [ 19.400968] address 400900 data db6c7c3c
- [ 19.407560]
- [ 19.407560] CLOCK PLL skipped
- [ 19.411152] HIF_PCIDeviceProbed: setting the target pll frac ffffffff intval ffffffff
- [ 19.420181] HIF_PCIDeviceProbed: no frac provided, skipping pre-configuring PLL
- [ 19.426491] HIF_PCIDeviceProbed: ar900b_20_targ_clk is not provided, skipping pre-configuring PLL
- [ 19.435332]
- [ 19.435332] address 4008cc data db6c7c3c
- [ 19.442924] __ol_ath_attach: ath_attach TODO
- [ 19.446204] __ol_ath_attach 1755 host_enable 0 nss_nwifi_offload 0
- [ 19.452358] __ol_ath_attach: dev name wifi1
- [ 19.456544] ol_ath_set_default_tgt_config : AC Minfree buffer allocation through module param (umac.ko)
- [ 19.465948] OL_ACBKMinfree : 0
- [ 19.469009] OL_ACBEMinfree : 0
- [ 19.472133] OL_ACVIMinfree : 0
- [ 19.475320] OL_ACVOMinfree : 0
- [ 19.478412] ol_ath_attach() BMI inited.
- [ 19.482318] ol_ath_attach() BMI Get Target Info.
- [ 19.486816] ol_ath_attach() TARGET TYPE: 9 Vers 0x1000000
- [ 19.492189]
- [ 19.492189] CE WAR Disabled
- [ 19.496688] NUM_DEV=1 FWMODE=0x2 FWSUBMODE=0x0 FWBR_BUF 0
- [ 19.502124] ol_ath_attach() configure Target .
- [ 19.506435]
- [ 19.506435] Target Version is 1000000
- [ 19.511558]
- [ 19.511558] Flash Download Address c0000
- [ 19.517213] ol_transfer_bin_file: flash data file defined
- [ 19.522586] Cal location [1]: 00004000
- [ 19.526398]
- [ 19.526398] Wifi1 Select OFFSET 5000
- [ 19.550390] qc98xx_verify_checksum: flash checksum passed: 0x2dfd
- [ 19.555451] ol_transfer_bin_file 2935: Download Flash data len 12064
- [ 19.562011] Board extended Data download address: 0x0
- [ 19.587035]
- [ 19.587066] Board data initialized
- [ 19.591034] Flash download ADDRESS 0xc0000
- [ 19.595064]
- [ 19.595064] Selecting OTP binary for CHIP Version 1
- [ 19.649828]
- [ 19.649828] First OTP send param 8000
- [ 19.657325] ol_ath_download_firmware :First OTP download and Execute is good return param 36864
- [ 19.665260]
- [ 19.665260] ##Board Id 4
- [ 19.669165]
- [ 19.669165] ##CHIP Id 1
- [ 19.673133]
- [ 19.673133] BOARDDATA DOWNLOAD TO address c0000
- [ 19.679256] ol_transfer_bin_file: Board data file: AR900B/hw.2/boardData_AR900B_CUS238_5GMipiHigh_v2_004.bin ARXXXX v=0x1
- [ 19.706904] Board extended Data download address: 0x0
- [ 19.731271] ol_ath_download_firmware: Using 0x1234 for the remainder of init
- [ 19.737332]
- [ 19.737332] Selecting OTP binary for CHIP Version 1
- [ 19.762511] [wifi0] FWLOG: [19263] WAL_DBGID_TX_AC_BUFFER_SET ( 0x3, 0x1e, 0x518, 0x518, 0x0 )
- [ 19.770071] [wifi0] FWLOG: [19263] WAL_DBGID_TX_AC_BUFFER_SET ( 0x12, 0x1e, 0x518, 0x518, 0x0 )
- [ 19.778787] [wifi0] FWLOG: [19263] WAL_DBGID_TX_AC_BUFFER_SET ( 0x45, 0x1e, 0x518, 0x518, 0x0 )
- [ 19.787441] [wifi0] FWLOG: [19263] WAL_DBGID_TX_AC_BUFFER_SET ( 0x67, 0x1e, 0x518, 0x518, 0x0 )
- [ 19.806872]
- [ 19.806872] Second otp download Param 10000
- [ 19.822617] ol_ath_download_firmware : OTP download and Execute is good
- [ 19.828303]
- [ 19.828303] FIRMWARE : Beeliner CHIP Version 1
- [ 19.851421] ol_swap_seg_alloc: Successfully allocated memory for SWAP size=131072
- [ 19.876257] Swap: bytes_left to copy: fw:16; dma_page:24579
- [ 19.880849] Swap: wrong length read:0
- [ 19.884473] ol_swap_wlan_memory_expansion: Swap total_bytes copied: 106493 Target address 417968
- [ 19.895470] scn=d95c04c0 target_write_addr=417968 seg_info=de2a2310
- [ 19.900905] ol_transfer_swap_struct:Code swap structure successfully downloaded for bin type =2
- [ 19.909809] bin_filename=AR900B/hw.2/athwlan.bin swap_filename=/lib/firmware/AR900B/hw.2/athwlan.codeswap.bin
- [ 21.025616] ol_ath_attach() Download FW.
- [ 21.028647] ol_ath_attach() HT Create .
- [ 21.032427] ol_ath_attach() HIF Claim.
- [ 21.036301] ol_ath_attach() BMI Done.
- [ 21.039893] ol_ath_attach() WMI attached. wmi_handle da040000
- [ 21.045735] +HWT
- [ 21.050171] CE_recv_buf_enqueue 809 Populate last entry 512 for CE 5
- [ 21.055482] CE_recv_buf_enqueue 818 CE 5 wi 511 dest_ptr 0x5a0aa040 nbytes 0 recv_ctxt 0xdba5c0c0
- [ 21.064761] Target:db3c4800 HTC Service:0x0001, ULpipe:0 DLpipe:1 id:0 Ready
- [ 21.071415] -HWT
- [ 21.073320]
- [ 21.073320] <=== cfg max peer id 1056 ====>
- [ 21.078975] Target:db3c4800 HTC Service:0x0300, ULpipe:4 DLpipe:5 id:1 Ready
- [ 21.085910] HTC Service:0x0300 ep:1 TX flow control disabled
- [ 21.093127] CE_pkt_dl_len_set CE 4 Pkt download length 64
- [ 21.097532] ol_txrx_pdev_attach: 1424 tx desc's allocated ; range starts from d88b0000
- [ 21.105654] Target:db3c4800 HTC Service:0x0100, ULpipe:3 DLpipe:2 id:2 Ready
- [ 21.112433] HTC Service:0x0100 ep:2 TX flow control disabled
- [ 21.118900] wmi_service_ready_event_rx: WMI UNIFIED SERVICE READY event
- [ 21.124835] num_rf_chain : 00000004
- [ 21.128272] ht_cap_info: : 0000085b
- [ 21.131771] vht_cap_info : 339b79b2
- [ 21.135238] vht_supp_mcs : 0000ffea
- [ 21.138706] ol_ath_service_ready_event: tt_support: 1
- [ 21.143736] Peer Caching Enabled ; num_peers = 528, num_active_peers = 66 num_tids = 132, num_vdevs = 16
- [ 21.153202] idx 0 req 1 num_units 0 num_unit_info 2 unit size 1208 actual units 529
- [ 21.161449] idx 1 req 2 num_units 1 num_unit_info 4 unit size 256 actual units 67
- [ 21.168666] idx 2 req 3 num_units 1 num_unit_info 4 unit size 1024 actual units 67
- [ 21.176444] idx 3 req 4 num_units 1 num_unit_info 4 unit size 4096 actual units 67
- [ 21.184286] idx 4 req 6 num_units 35 num_unit_info 0 unit size 3072 actual units 35
- [ 21.191971] idx 5 req 7 num_units 1 num_unit_info 0 unit size 6144 actual units 1
- [ 21.199562] idx 6 req 5 num_units 0 num_unit_info 2 unit size 2080 actual units 529
- [ 21.207997] chunk 0 len 639032 requested ,ptr 0x59e00000
- [ 21.212839] chunk 1 len 17152 requested ,ptr 0x5a590000
- [ 21.218275] chunk 2 len 68608 requested ,ptr 0x59f00000
- [ 21.223586] chunk 3 len 274432 requested ,ptr 0x59f80000
- [ 21.229084] chunk 4 len 107520 requested ,ptr 0x59f20000
- [ 21.234520] chunk 5 len 6144 requested ,ptr 0x5a5ce000
- [ 21.239862] chunk 6 len 1100320 requested ,ptr 0x59800000
- [ 21.321149] wmi_ready_event_rx: WMI UNIFIED READY event
- [ 21.325585] ol_ath_connect_htc() WMI is ready
- [ 21.329865] ol_ath_set_host_app_area TODO
- [ 21.333895] target uses HTT version 2.1; host uses 2.1
- [ 21.344048] ol_ath_attach() connect HTC.
- [ 21.347079] ol_regdmn_start: reg-domain param: regdmn=0, countryName=, wModeSelect=FFFFFFFF, netBand=FFFFFFFF, extendedChanMode=0.
- [ 21.358856] ol_regdmn_init_channels: !avail mode 0x1f9001 (0x2) flags 0x2150
- [ 21.365854] ol_regdmn_init_channels: !avail mode 0x1f9001 (0x4) flags 0xa0
- [ 21.372664] ol_regdmn_init_channels: !avail mode 0x1f9001 (0x8) flags 0xc0
- [ 21.379537] ol_regdmn_init_channels: !avail mode 0x1f9001 (0x20) flags 0xd0
- [ 21.386472] ol_regdmn_init_channels: !avail mode 0x1f9001 (0x40) flags 0x150
- [ 21.393502] ol_regdmn_init_channels: !avail mode 0x1f9001 (0x800) flags 0x10080
- [ 21.400781] ol_regdmn_init_channels: !avail mode 0x1f9001 (0x2000) flags 0x20080
- [ 21.408153] ol_regdmn_init_channels: !avail mode 0x1f9001 (0x4000) flags 0x40080
- [ 21.415588] Add VHT80 channel: 5210
- [ 21.419056] Add VHT80 channel: 5290
- [ 21.422461] Add VHT80 channel: 5530
- [ 21.425960] Add VHT80 channel: 5610
- [ 21.429428] Add VHT80 channel: 5690
- [ 21.432895] Add VHT80 channel: 5775
- [ 21.436394] Skipping VHT80 channel 5825
- [ 21.440487] ol_ath_phyerr_attach: called
- [ 21.444173] OL Resmgr Init-ed
- [ 21.448328] ieee80211_bsteering_attach: Band steering initialized
- [ 21.453420] ol_if_spectral_setup
- [ 21.456638] SPECTRAL : get_capability not registered
- [ 21.461574] HAL_CAP_PHYDIAG : Capable
- [ 21.465229] SPECTRAL : Need to fix the capablity check for RADAR (spectral_attach : 231)
- [ 21.473352] SPECTRAL : get_capability not registered
- [ 21.478256] HAL_CAP_RADAR : Capable
- [ 21.481880] SPECTRAL : Need to fix the capablity check for SPECTRAL
- [ 21.481880] (spectral_attach : 236)
- [ 21.491721] SPECTRAL : get_capability not registered
- [ 21.496657] HAL_CAP_SPECTRAL_SCAN : Capable
- [ 21.500812] SPECTRAL : get_tsf64 not registered
- [ 21.505310] spectral_init_netlink 65 NULL SKB
- [ 21.509684] Green-AP : Green-AP : Attached
- [ 21.509684]
- [ 21.515245] Green-AP : Attached
- [ 21.518369] rate power table override is only supported for AR98XX
- [ 21.524554] ol_ath_smart_ant_attach: Hardware doest not support Smart Antenna.
- [ 21.531740] ieee80211com_init_netlink: Socket already created db5fd800
- [ 21.538269] ol_if_dfs_setup: called
- [ 21.541861] ol_if_dfs_attach: called; ptr=d8ac5984, radar_info=db6c7be0
- [ 21.548609] ol_ath_rtt_meas_report_attach: called
- [ 21.553452] ol_ath_attach() UMAC attach .
- [ 21.557200] ol_if_dfs_configure: called
- [ 21.560980] ol_if_dfs_configure: FCC domain
- [ 21.565135] ol_if_dfs_disable: called
- [ 21.568853] ol_ath_attach: Calling ol_if_dfs_configure
- [ 21.573883]
- [ 21.573883] BURSTING enabled by default
- [ 21.579412] osif_wrap_attach:400 osif wrap attached
- [ 21.584161] osif_wrap_devt_init:361 osif wrap dev table init done
- [ 21.590253] Wrap Attached: Wrap_com =db602c00 ic->ic_wrap_com=db602c00 &wrap_com->wc_devt=db602c00
- [ 21.599343] __ol_ath_attach: init tx/rx TODO
- [ 21.603592] __ol_ath_attach: needed_headroom reservation 44
- [ 21.612027] ol_ath_thermal_mitigation_attach: ++
- [ 21.615682] ol_ath_thermal_mitigation_attach: --
- /bin/sh: update_smp_affinity: Permission denied
- [ 21.770009] set TXBF_SND_PERIOD: value 100 wmi_status 0
- [ 21.974289] ath_ioctl: SIOC80211IFCREATE CALLED
- [ 21.977881] wmi_unified_vdev_create_send: ID = 0 Type = 1, Subtype = 0 VAP Addr = 50:c7:bf:08:60:e7:
- [ 21.987503] __ieee80211_smart_ant_init: Smart Antenna functions are not registered !!!
- [ 21.995064] Enabling SG bit for the vap ath0 features 4000
- [ 22.000562] Enabling TSO bit for the vap ath0 features 4000
- [ 22.006123] Enabling LRO bit for the vap ath0 features 4000
- [ 22.011777] VAP device ath0 created osifp: (db3c6cc0) os_if: (db438000)
- ath0
- [ 22.029147] su bfee 1 mu bfee 0 su bfer 1 mu bfer 0 impl bf 0 sounding dim 3
- [ 22.041518] [wifi1] FWLOG: [21552] WAL_DBGID_TX_AC_BUFFER_SET ( 0x3, 0x1e, 0x518, 0x518, 0x0 )
- [ 22.049078] [wifi1] ath_ioctl: SIOC80211IFCREATE CALLED
- [ 22.049609] wmi_unified_vdev_create_send: ID = 1 Type = 2, Subtype = 0 VAP Addr = 52:c7:bf:08:60:e7:
- [ 22.049703] wmi_unified_set_psmode:set psmode=1
- [ 22.050015] __ieee80211_smart_ant_init: Smart Antenna functions are not registered !!!
- [ 22.050015] Enabling SG bit for the vap ath1 features 4000
- [ 22.050046] Enabling TSO bit for the vap ath1 features 4000
- [ 22.050046] Enabling LRO bit for the vap ath1 features 4000
- [ 22.050046] VAP device ath1 created osifp: (db5944c0) os_if: (d844c000)
- ath1
- [ 22.099625] FWLOG: [21552] WAL_DBGID_TX_AC_BUFFER_SET ( wmi_unified_set_psmode:set psmode=0
- [ 22.103373] wmi_unified_set_psmode:set psmode=0
- [ 22.107247] wmi_unified_set_psmode:set psmode=0
- [ 22.107278] wmi_unified_set_psmode:set psmode=0
- [ 22.114839] su bfee 1 mu bfee 0 su bfer 1 mu bfer 0 impl bf 0 sounding dim 3
- [ 22.121930] ath_ioctl: SIOC80211IFCREATE CALLED
- [ 22.121961] wmi_unified_vdev_create_send: ID = 2 Type = 1, Subtype = 0 VAP Addr = 62:c7:bf:08:60:e7:
- [ 22.122305] __ieee80211_smart_ant_init: Smart Antenna functions are not registered !!!
- [ 22.122336] Enabling SG bit for the vap ath2 features 4000
- [ 22.122336] Enabling TSO bit for the vap ath2 features 4000
- [ 22.122336] Enabling LRO bit for the vap ath2 features 4000
- [ 22.122336] VAP device ath2 created osifp: (db595cc0) os_if: (da230000)
- ath2
- [ 22.174414] 0x12, 0x1e, 0x518, 0x518, su bfee 1 mu bfee 0 su bfer 1 mu bfer 0 impl bf 0 sounding dim 3
- [ 22.183692] 0x0 )
- [ 22.185567] [wifi1] FWLOG: [21552] WAL_DBGID_TX_AC_BUFFER_SET ( 0x45
- [ 22.191596] DES SSID SET=TP-LINK_60E7
- [ 22.195845] , 0x1e, 0x518, 0x518, 0x0 )
- [ 22.199625] [wifi1] FWLOG: [21552] WAL_DBGID_TX_AC_BUFFER_SET ( [ol_ath_iw_setcountry][1660] *p=44, *(p+1)=45
- [ 22.203280] isCountryCodeValid: EEPROM regdomain 0x0
- [ 22.203311] ol_regdmn_init_channels: !avail mode 0x680c (0x2) flags 0x2150
- [ 22.203311] ol_regdmn_init_channels: !avail mode 0x680c (0x1) flags 0x140
- [ 22.203342] ol_regdmn_init_channels: !avail mode 0x680c (0x20) flags 0xd0
- [ 22.203342] ol_regdmn_init_channels: !avail mode 0x680c (0x40) flags 0x150
- [ 22.203342] ol_regdmn_init_channels: !avail mode 0x680c (0x1000) flags 0x10100
- [ 22.203342] ol_regdmn_init_channels: !avail mode 0x680c (0x8000) flags 0x20100
- [ 22.203373] ol_regdmn_init_channels: !avail mode 0x680c (0x10000) flags 0x40100
- [ 22.203373] ol_regdmn_init_channels: !avail mode 0x680c (0x20000) flags 0x100100
- [ 22.203373] ol_regdmn_init_channels: !avail mode 0x680c (0x40000) flags 0x200100
- [ 22.203373] ol_regdmn_init_channels: !avail mode 0x680c (0x80000) flags 0x400100
- [ 22.203373] ol_regdmn_init_channels: !avail mode 0x680c (0x100000) flags 0x800100
- [ 22.214589] Set freq vap 0 stop send + db438000
- [ 22.214589] OL vap_stop +
- [ 22.214620] wmi_unified_vdev_stop_send for vap 0 (da250000)
- [ 22.214620] OL vap_stop -
- [ 22.214714] Set freq vap 0 stop send -db438000
- [ 22.313245] STOPPED EVENT for vap 0 (da250000)
- [ 22.316994] Set wait done --db438000
- [ 22.316994] Set freq vap 0 stop send + d844c000
- [ 22.317057] Set freq vap 0 stop send -d844c000
- [ 22.329803] 0x67, 0x1e, 0x518, 0x518, 0x0 )
- [ 22.339831] Set wait done --d844c000
- [ 22.342361] Set freq vap 0 stop send + da230000
- [ 22.347047] OL vap_stop +
- [ 22.349484] wmi_unified_vdev_stop_send for vap 2 (da250000)
- [ 22.355014] OL vap_stop -
- [ 22.355045] STOPPED EVENT for vap 2 (da250000)
- [ 22.362168] Set freq vap 0 stop send -da230000
- [ 22.396626] Set wait done --da230000
- [ 22.422836] ME Pool succesfully initialized vaddr - d7f00000 paddr - 0
- [ 22.422836] num_elems = 10424 buf_size - 64 pool_size = 708832
- [ 22.434208] Enable MCAST_TO_UCAST
- [ 22.452889] WARNING: Fragmentation with HT mode NOT ALLOWED!!
- Error for wireless request "Set Fragmentation Threshold" (8B24) :
- SET failed on device ath0 ; Invalid argument.
- [ 22.477600] Setting Max Stations:64
- [ 22.511121]
- [ 22.511121] DES SSID SET=TP-LINK_Guest_60E7
- [ 22.543142] ol_tx_me_init:Already Enabled!!
- [ 22.546485] Enable MCAST_TO_UCAST
- [ 22.561074] WARNING: Fragmentation with HT mode NOT ALLOWED!!
- Error for wireless request "Set Fragmentation Threshold" (8B24) :
- SET failed on device ath2 ; Invalid argument.
- [ 22.585504] Setting Max Stations:64
- Reading topology file /var/Wireless/2_4G_topology.conf ...
- 022.881: Reading radio configuration file /var/Wireless/2_4G_80211g.ap_radio ...
- 022.881: Reading bss configuration file /var/Wireless/ath0.ap_bss ...
- [ 23.025648] ieee80211_ioctl_siwmode: imr.ifm_active=131712, new mode=3, valid=1
- Using interface ath0 with hwaddr 50:c7:bf:08:60:e7 and ssid 'TP-LINK_60E7'
- [ 23.084817]
- [ 23.084817] DES SSID SET=TP-LINK_60E7
- 023.094: upnp_wps_device_init called
- l2_packet_receive - recvfrom: Network is down
- [ 23.641424] device ath0 entered promiscuous mode
- atheros_wireless_event_receive:Malformed netlink message: len=1008 left=512 plen=992
- 512 extr[ 23.648734] device ath1 entered promiscuous mode
- a bytes in the end of netlink message
- atheros_wireless_event_receive:Malformed netlink message: len=10[ 23.661387] device ath2 entered promiscuous mode
- 08 left=512 plen=992
- 512 extra bytes in the end of netlink message
- atheros_wireless_event_receive:Malformed netlink message: len=1008 left=512 plen=992
- 512 extra bytes in the end of netlink message
- *********cal_data_2g*******
- 202f612a0000000016000000
- *********cal_data_end*******
- *********cal_data_5g*******
- 202ffd2d0000000000161616
- *********cal_data_end*******
- /bin/sh: update_smp_affinity: Permission denied
- atheros_wireless_event_receive:Malformed netlink message: len=1000 left=512 plen=984
- 512 extra bytes in the end of netlink message
- [ 23.756638] set TXBF_SND_PERIOD: value 100 wmi_status 0
- [ 23.763761] [wifi0] FWLOG: [23409] WAL_DBGID_SECURITY_ENCR_EN ( 0x60e7 )
- [ 23.769415] [wifi0] FWLOG: [23409] WAL_DBGID_SECURITY_MCAST_KEY_SET ( 0x1 )
- atheros_wireless_event_receive:Malformed netlink message: len=1004 left=512 plen=988
- 512 extr[ 23.782942] ath_ioctl: SIOC80211IFCREATE CALLED
- a bytes in the end of netlink message
- [ 23.791252] wmi_unified_vdev_create_send: ID = 0 Type = 1, Subtype = 0 VAP Addr = 50:c7:bf:08:60:e9:
- [ 23.804029] __ieee80211_smart_ant_init: Smart Antenna functions are not registered !!!
- [ 23.811715] Enabling SG bit for the vap ath5 features 4000
- [ 23.817463] Enabling TSO bit for the vap ath5 features 4000
- [ 23.822836] Enabling LRO bit for the vap ath5 features 4000
- [ 23.828491] VAP device ath5 created osifp: (d86a3cc0) os_if: (d86cc000)
- ath5
- atheros_wireless_event_receive:Malformed netlink message: len=1000 left=512 plen=984
- 512 extr[ 23.844361] ath_ioctl: SIOC80211IFCREATE CALLED
- a bytes in the end of netlink message
- [ 23.853202] wmi_unified_vdev_create_send: ID = 1 Type = 2, Subtype = 0 VAP Addr = 52:c7:bf:08:60:e9:
- [ 23.865760] wmi_unified_set_psmode:set psmode=1
- [ 23.870415] __ieee80211_smart_ant_init: Smart Antenna functions are not registered !!!
- [ 23.878131] Enabling SG bit for the vap ath6 features 4000
- [ 23.883661] Enabling TSO bit for the vap ath6 features 4000
- [ 23.889378] Enabling LRO bit for the vap ath6 features 4000
- [ 23.894939] VAP device ath6 created osifp: (d86a6cc0) os_if: (d8484000)
- ath6
- atheros_wireless_event_receive:Malformed netlink message: len=1000 left=512 plen=984
- 512 extr[ 23.908559] wmi_unified_set_psmode:set psmode=0
- a bytes in the end of net[ 23.916994] wmi_unified_set_psmode:set psmode=0
- link message
- [ 23.927491] wmi_unified_set_psmode:set psmode=0
- [ 23.931021] wmi_unified_set_psmode:set psmode=0
- [ 23.938925] ath_ioctl: SIOC80211IFCREATE CALLED
- [ 23.942455] wmi_unified_vdev_create_send: ID = 2 Type = 1, Subtype = 0 VAP Addr = 62:c7:bf:08:60:e9:
- [ 23.951952] __ieee80211_smart_ant_init: Smart Antenna functions are not registered !!!
- [ 23.959575] Enabling SG bit for the vap ath7 features 4000
- [ 23.965073] Enabling TSO bit for the vap ath7 features 4000
- [ 23.970759] Enabling LRO bit for the vap ath7 features 4000
- [ 23.976413] VAP device ath7 created osifp: (d86a34c0) os_if: (d84a8000)
- ath7
- atheros_wireless_event_receive:Malformed netlink message: len=1000 left=512 plen=984
- 512 extr[ 23.992127]
- [ 23.992127] DES SSID SET=TP-LINK_60E7_5G
- a bytes in the end of netlink message
- atheros_wireless_event_receive:Malformed netlink message: len=1004 left=512 plen=988
- 512 extr[ 24.011090] [ol_ath_iw_setcountry][1660] *p=44, *(p+1)=45
- [ 24.019462] isCountryCodeValid: EEPROM regdomain 0x0
- [ 24.024367] ol_regdmn_init_channels: !avail mode 0x1f9001 (0x2) flags 0x2150
- a bytes in the end of netlink message
- [ 24.031521] ol_regdmn_init_channels: !avail mode 0x1f9001 (0x4) flags 0xa0
- [ 24.041674] ol_regdmn_init_channels: !avail mode 0x1f9001 (0x8) flags 0xc0
- [ 24.048578] ol_regdmn_init_channels: !avail mode 0x1f9001 (0x20) flags 0xd0
- [ 24.055420] ol_regdmn_init_channels: !avail mode 0x1f9001 (0x40) flags 0x150
- [ 24.062480] ol_regdmn_init_channels: !avail mode 0x1f9001 (0x800) flags 0x10080
- [ 24.069759] ol_regdmn_init_channels: !avail mode 0x1f9001 (0x2000) flags 0x20080
- [ 24.077163] ol_regdmn_init_channels: !avail mode 0x1f9001 (0x4000) flags 0x40080
- [ 24.084536] Add VHT80 channel: 5210
- [ 24.088003] Add VHT80 channel: 5290
- [ 24.091471] Add VHT80 channel: 5530
- [ 24.094939] Add VHT80 channel: 5610
- [ 24.098437] Skipping VHT80 channel 5660
- [ 24.102218] Skipping VHT80 channel 5680
- [ 24.106091] Skipping VHT80 channel 5700
- atheros_wireless_event_receive:Malformed netlink message: len=1004 left=512 plen=988
- 512 extra bytes in the end of netlink message
- [ 24.121680] Set freq vap 0 stop send + d86cc000
- [ 24.129115] OL vap_stop +
- [ 24.131677] wmi_unified_vdev_stop_send for vap 0 (da040000)
- [ 24.137300] OL vap_stop -
- [ 24.137363] STOPPED EVENT for vap 0 (da040000)
- [ 24.144329] Set freq vap 0 stop send -d86cc000
- [ 24.176632] Set wait done --d86cc000
- [ 24.179162] Set freq vap 0 stop send + d8484000
- [ 24.183723] Set freq vap 0 stop send -d8484000
- [ 24.216651] Set wait done --d8484000
- [ 24.219181] Set freq vap 0 stop send + d84a8000
- [ 24.223680] OL vap_stop +
- [ 24.226304] wmi_unified_vdev_stop_send for vap 2 (da040000)
- [ 24.231833] OL vap_stop -
- [ 24.234489] STOPPED EVENT for vap 2 (da040000)
- [ 24.234489] Set freq vap 0 stop send -d84a8000
- [ 24.256638] Set wait done --d84a8000
- [ 24.282724] ME Pool succesfully initialized vaddr - d8200000 paddr - 0
- [ 24.282724] num_elems = 10424 buf_size - 64 pool_size = 708832
- [ 24.294095] Enable MCAST_TO_UCAST
- [ 24.312839] WARNING: Fragmentation with HT mode NOT ALLOWED!!
- Error for wireless request "Set Fragmentation Threshold" (8B24) :
- SET failed on device ath5 ; Invalid argument.
- [ 24.340674] Setting Max Stations:64
- [ 24.374445]
- [ 24.374445] DES SSID SET=TP-LINK_Guest_60E7_5G
- [ 24.407372] ol_tx_me_init:Already Enabled!!
- [ 24.410527] Enable MCAST_TO_UCAST
- [ 24.425304] WARNING: Fragmentation with HT mode NOT ALLOWED!!
- Error for wireless request "Set Fragmentation Threshold" (8B24) :
- SET failed on device ath7 ; Invalid argument.
- [ 24.450015] Setting Max Stations:64
- Reading topology file /var/Wireless/5G_topology.conf ...
- 024.492: Reading radio configuration file /var/Wireless/5G_80211g.ap_radio ...
- 024.493: Reading bss configuration file /var/Wireless/ath5.ap_bss ...
- [ 24.575663] ieee80211_ioctl_siwmode: imr.ifm_active=66176, new mode=3, valid=1
- Using interface ath5 with hwaddr 50:c7:bf:08:60:e9 and ssid 'TP-LINK_60E7_5G'
- [ 24.634676]
- [ 24.634676] DES SSID SET=TP-LINK_60E7_5G
- 024.644: upnp_wps_device_init called
- l2_packet_receive - recvfrom: Network is down
- starting pid 1024, tty '': '/sbin/getty -L ttyHSL1 115200 vt100'
- [ 25.041205] [wifi1] FWLOG: [24955] WAL_DBGID_SECURITY_ENCR_EN ( 0x60e9 )
- [ 25.046860] [wifi1] FWLOG: [24955] WAL_DBGID_SECURITY_MCAST_KEY_SET ( 0x1 )
- Archer VR2600v login: [ 25.504342] device ath5 entered promiscuous mode
- atheros_wireless_event_receive:Malformed netlink message: len=1008 left=512 plen=992
- 512 extr[ 25.511715] device ath6 entered promiscuous mode
- a bytes in the end of netlink message
- atheros_wireless_event_re[ 25.524835] device ath7 entered promiscuous mode
- ceive:Malformed netlink message: len=1008 left=512 plen=992
- 512 extra bytes in the end of netlink message
- atheros_wireless_event_receive:Malformed netlink message: len=1008 left=512 plen=992
- 512 extra bytes in the end of netlink message
- atheros_wireless_event_receive:Malformed netlink message: len=1008 left=512 plen=992
- 512 extra bytes in the end of netlink message
- atheros_wireless_event_receive:Malformed netlink message: len=1008 left=512 plen=992
- 512 extra bytes in the end of netlink message
- atheros_wireless_event_receive:Malformed netlink message: len=1008 left=512 plen=992
- 512 extra bytes in the end of netlink message
- sendto: No such file or directory
- pid 1023 send 2030 error
- sendto: No such file or directory
- pid 1023 send 2004 error
- iptables: Bad rule (does a matching rule exist in that chain?).
- radvd starting
- [setBusinessSocks : 131] g_sockvoiceapp = -1
- [ getPidFromPidFile ] 112: Cann't open file: /var/run/zebra.pid.
- [ getPidFromPidFile ] 112: Cann't open file: /var/run/ripd.pid.
- [ 27.975320]
- [ 27.975320] tplink_deaccelerate_all OK.
- iptables: Bad rule (does a matching rule exist in that chain?).
- [ 27.996532]
- [ 27.996532] tplink_deaccelerate_all OK.
- iptables: Bad rule (does a matching rule exist in that chain?)[ 28.009621]
- [ 28.009621] tplink_deaccelerate_all OK.
- .
- Archer VR2600v login: iptables: Bad rule (does a matching rule exist in that chain?).
- ip6tables: Bad rule (does a matching rule exist in that chain?).
- /home/newdev/AC2600/linux_qca_AC2600/build/../apps/private/voip/src/common/voip_comm.c:497 ether.dst=8e164851c142
- /home/newdev/AC2600/linux_qca_AC2600/build/../apps/private/voip/src/common/voip_comm.c:500 ether.proto=dd01
- /home/newdev/AC2600/linux_qca_AC2600/build/../apps/private/voip/src/common/voip_comm.c:497 ether.dst=8e164851c142
- /home/newdev/AC2600/linux_qca_AC2600/build/../apps/private/voip/src/common/voip_comm.c:500 ether.proto=dd03
- /home/newdev/AC2600/linux_qca_AC2600/build/../apps/private/voip/src/common/voip_comm.c:1083 [0;31mrecv ack thread start[0m
- /home/newdev/AC2600/linux_qca_AC2600/build/../apps/private/voip/src/common/voip_comm.c:497 ether.dst=8e164851c142
- /home/newdev/AC2600/linux_qca_AC2600/build/../apps/private/voip/src/common/voip_comm.c:500 ether.proto=dd02
- [ rsl_setStorageServiceObj ] 1394: mountFlag is 3,We start usb server
- killall: minidlnad: no process killed
- Archer VR2600v login: adminiptables: Bad rule (does a matching rule exist in that chain?).
- iptables: Bad rule (does a matching rule exist in that chain?).
- ip6tables: Bad rule (does a matching rule exist in that chain?).
- [ 32.397719] kcg 333 :GPL NetUSB up!
- [ 32.434489] kc 90 : run_telnetDBGDServer start
- [ 32.438238] kc 227 : init_DebugD end
- [ 32.441830] INFO17ED: NetUSB 1.02.67, 00030467 : May 15 2015 16:22:12
- [ 32.448422] INFO17EF: 7437: Archer VR2600v :Archer VR2600v
- [ 32.453795] INFO17F0: AUTH ISOC
- [ 32.457044] INFO17F1: filterAudio
- [ 32.460668] usbcore: registered new interface driver KC NetUSB General Driver
- [ 32.469665] INFO0145: init proc : PAGE_SIZE 4096
- [ 32.469665] INFO16E1: infomap bf799bc4
- [ 32.469665] INFO16E4: sleep to wait br0 to wake up
- [ 32.482193] INFO15B4: tcpConnector() started... : br0
- SSDK Init OK!
- operate done.
- SSDK Init OK!
- operate done.
- SSDK Init OK!
- operate done.
- SSDK Init OK!
- operate done.
- SSDK Init OK!
- operate done.
- SSDK Init OK!
- operate done.
- SSDK Init OK!
- operate done.
- Enable forwarding
- Password: [ 32.589784] Erase from 0xf90000 with 0x1f5e bytes, mtd->erasesize 0x10000
- [ 32.595813] .
- [ 32.597094] erase successed!
- [ 32.599968]
- [ 32.601437] Write to flash:0xf90000, len is 0x1f5e
- [ 32.945204] Erase from 0xf90000 with 0x1f5e bytes, mtd->erasesize 0x10000
- [ 32.951171] .
- [ 32.952514] erase successed!
- [ 32.955388]
- [ 32.956919] Write to flash:0xf90000, len is 0x1f5e
- [ 33.304467] Erase from 0xf90000 with 0x1f5e bytes, mtd->erasesize 0x10000
- [ 33.310434] .
- [ 33.311777] erase successed!
- [ 33.314651]
- [ 33.316151] Write to flash:0xf90000, len is 0x1f5e
- [ 33.669790] Erase from 0xf90000 with 0x1f5e bytes, mtd->erasesize 0x10000
- [ 33.675726] .
- [ 33.677100] erase successed!
- [ 33.679975]
- [ 33.681443] Write to flash:0xf90000, len is 0x1f5e
- [ 34.034051] Erase from 0xf90000 with 0x1f5e bytes, mtd->erasesize 0x10000
- [ 34.040018] .
- [ 34.041362] erase successed!
- [ 34.044236]
- [ 34.045735] Write to flash:0xf90000, len is 0x1f5e
- [ 34.392564] Erase from 0xf90000 with 0x1f5e bytes, mtd->erasesize 0x10000
- [ 34.398531] .
- [ 34.399875] erase successed!
- [ 34.402780]
- [ 34.404248] Write to flash:0xf90000, len is 0x1f5e
- firm version:1.1.0 0.8.0 v004f.0 Build 160215 Rel.30334n
- hard version:Archer VR2600v v1 00000000
- firm version:1.1.0 0.8.0 v004f.0 Build 160215 Rel.30334n
- hard version:Archer VR2600v v1 00000000
Advertisement
Add Comment
Please, Sign In to add comment
Advertisement