Advertisement
Not a member of Pastebin yet?
Sign Up,
it unlocks many cool features!
- picocom /dev/ttyUSB1 -b 57600
- picocom v1.7
- port is : /dev/ttyUSB1
- flowcontrol : none
- baudrate is : 57600
- parity is : none
- databits are : 8
- escape is : C-a
- local echo is : no
- noinit is : no
- noreset is : no
- nolock is : no
- send_cmd is : sz -vv
- receive_cmd is : rz -vv
- imap is :
- omap is :
- emap is : crcrlf,delbs,
- Terminal ready
- (SAP)old_avapi:AV_IO_CTL_STOP
- audio_hw_set_treble error
- audio_hw_set_bass error
- system_if_usb_select_device, val: 1
- (SAP)old_avapi:AV_IO_SET_EQUALIZER
- line_ctl_disable
- ap head used=0x006721f8, free=0x0198de08
- os head used=0x0022b098, free=0x015d4f68
- (SAP)old_avapi:AV_IO_CTL_STOP
- audio_hw_set_treble error
- audio_hw_set_bass error
- system_if_usb_select_device, val: 1
- (SAP)old_avapi:AV_IO_SET_EQUALIZER
- line_ctl_disable
- the acin not exist
- the vbus not exist
- vbus_io_proc old usb is devctl = 0x00
- NOTIFY: USB_REMOVE_HARDWARE
- Disable USB Phy!
- (SAP)old_avapi:AV_IO_CTL_STOP
- lg_system_main out
- IPL: Serial ok Time:Mar 30 2015 15:04:57
- X00000004
- 00000001
- IPL: Sdram initted ...
- IPL: Starting SPL ...
- IPL: Freq:1F78A400
- IPL: Jump to SPL
- X-Boot: Getting boot sel keys ...
- X-Boot: SPL Build time: Mar 11 2015 16:51:53
- ***new hw
- X-Boot: Tcu has been inited ...
- nfdrv_init
- nfdrv_init finish
- X-Boot: Getting boot message ...
- 00000020 000000F0 00000140 X-Boot: boot_normal
- X-Boot: Load kernel from ihfs ...
- X-Boot: Load done.
- OS START...
- System Build Time:May 30 2016 09:36:49
- Hardware Version: HW_VERSION_V02.
- pmu_init
- pmu_set_dcdc2 read reg[0]=0x1c, level=1425
- pmu_set_dcdc2 write reg[0]=0x1d, level=725
- pmu_charging 0
- x3k_audio_hw
- FTL_Init
- nfdrv_init
- nfdrv_init finish
- iic0_lock create
- dev:25 fs_type:1 init success
- dev:24 fs_type:2 init success
- (OS:I)sd0_hotplug[173]: MMC0 Card Insert!
- (OS:I)mmc_core[98]: init------card---
- (OS:I)mmc_protocol[200]: SD_card found------
- (OS:I)mmc_protocol[141]: card_info: sd_20=1 block_len=512 block_num=124735488 rate=24000000 mode=1
- (OS:I)mmc_protocol[389]: 4 bit bus width
- (OS:I)mmc_core[116]: init------card--ok-
- dev->size:0x00000001
- dev:0 fs_type:4 init success
- lcd except debug open.
- init udc sys.
- USB Mass Storage Driver Build on May 30 2016 09:36:52 :
- Max lun: 1.
- Transfer Buffer Size: 128KB.
- DMA Enable.
- jz_musb_init start
- REG_CPM_CPCCR: 0x03633310
- REG_CPM_USBCDR: 0x00000000
- REG_CPM_USBPCR: 0x429921b5
- REG_CPM_USBRDT: 0x02000096
- jz_musb_init end
- REG_CPM_CPCCR: 0x03633310
- REG_CPM_USBCDR: 0x00000000
- REG_CPM_USBPCR: 0x439921ff
- REG_CPM_USBRDT: 0x0200013c
- phy reset end
- REG_CPM_CPCCR: 0x03633310
- REG_CPM_USBCDR: 0x00000000
- REG_CPM_USBPCR: 0x439921ff
- REG_CPM_USBRDT: 0x0200013c
- USB Driver Build on May 30 2016 09:36:51
- USB info list:
- Version: 2.0
- Config data: 0x12 ( HBRxE SoftConE )
- Total 5 RxEP, 5 TxEP.
- Total 6 DMA Channels, 2048 bytes RAM.
- lg_system_main in
- ap head used=0x0000a848, free=0x01ff57b8
- os head used=0x0018d4a0, free=0x01672b60
- audio_hw_set_treble error
- audio_hw_set_bass error
- system_if_usb_select_device, val: 1
- (SAP)old_avapi:AV_IO_SET_EQUALIZER
- line_ctl_disable
- (SAP)old_avapi:AV_IO_CTL_STOP
- lg_system_main out
Advertisement
Add Comment
Please, Sign In to add comment
Advertisement