Advertisement
Not a member of Pastebin yet?
Sign Up,
it unlocks many cool features!
- ROM VER: 1.0.3
- CFG 01
- Readü
- ROM VER: 1.0.3
- CFG 01
- Read EEPROMX
- X
- U-Boot 2010.03 (May 16 2012 - 05:51:08)
- Board: ARV4518PW
- SoC: Danube/Twinpass/Vinax-VE V1.5, DDR Speed 166 MHz, CPU Speed 333 MHz
- DRAM: 64 MB
- Flash: 4 MB
- Net:
- searching for rtl8306 switch ... found
- lq_cpe_eth
- Hit any key to stop autoboot: 0
- ## Booting kernel from Legacy Image at b0020000 ...
- Image Name: MIPS OpenWrt Linux-3.3.8
- Created: 2013-04-16 9:33:55 UTC
- Image Type: MIPS Linux Kernel Image (lzma compressed)
- Data Size: 965373 Bytes = 942.7 kB
- Load Address: 80002000
- Entry Point: 80002000
- Verifying Checksum ... OK
- Uncompressing Kernel Image ... OK
- Starting kernel ...
- [ 0.000000] Linux version 3.3.8 (berto@debian) (gcc version 4.6.3 20120201 (p
- rerelease) (Linaro GCC 4.6-2012.02) ) #1 Tue Apr 16 11:33:45 CEST 2013
- [ 0.000000] SoC: Danube rev 1.5
- [ 0.000000] bootconsole [early0] enabled
- [ 0.000000] CPU revision is: 00019641 (MIPS 24KEc)
- [ 0.000000] Determined physical RAM map:
- [ 0.000000] memory: 04000000 @ 00000000 (usable)
- [ 0.000000] Initrd not found or empty - disabling initrd
- [ 0.000000] Zone PFN ranges:
- [ 0.000000] Normal 0x00000000 -> 0x00004000
- [ 0.000000] Movable zone start PFN for each node
- [ 0.000000] Early memory PFN ranges
- [ 0.000000] 0: 0x00000000 -> 0x00004000
- [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pag
- es: 16256
- [ 0.000000] Kernel command line: console=ttyLTQ1,115200 rootfstype=squashfs,j
- ffs2 machtype=ARV4518PW
- [ 0.000000] PID hash table entries: 256 (order: -2, 1024 bytes)
- [ 0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
- [ 0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
- [ 0.000000] Primary instruction cache 16kB, VIPT, 4-way, linesize 32 bytes.
- [ 0.000000] Primary data cache 16kB, 4-way, VIPT, no aliases, linesize 32 byt
- es
- [ 0.000000] Writing ErrCtl register=00017d68
- [ 0.000000] Readback ErrCtl register=00017d68
- [ 0.000000] Memory: 61868k/65536k available (2272k kernel code, 3668k reserve
- d, 389k data, 172k init, 0k highmem)
- [ 0.000000] NR_IRQS:256
- [ 0.000000] CPU Clock: 333MHz
- [ 0.000000] Calibrating delay loop... 221.18 BogoMIPS (lpj=442368)
- [ 0.036000] pid_max: default: 32768 minimum: 301
- [ 0.040000] Mount-cache hash table entries: 512
- [ 0.048000] NET: Registered protocol family 16
- [ 0.056000] gpiochip_add: registered GPIOs 0 to 15 on device: ltq_gpio
- [ 0.060000] gpiochip_add: registered GPIOs 16 to 31 on device: ltq_gpio
- [ 0.064000] MIPS: machine is ARV4518PW - SMC7908A-ISP, Airties WAV-221
- [ 0.068000] gpiochip_add: registered GPIOs 100 to 115 on device: ltq_ebu
- [ 0.108000] bio: create slab <bio-0> at 0
- [ 0.116000] PCI host bridge to bus 0000:00
- [ 0.120000] pci_bus 0000:00: root bus resource [mem 0x18000000-0x19ffffff]
- [ 0.124000] pci_bus 0000:00: root bus resource [io 0x1ae00000-0x1affffff]
- [ 0.128000] pci 0000:00:0e.0: BAR 0: assigned [mem 0x18000000-0x1800ffff]
- [ 0.132000] pci 0000:00:0e.0: SLOT:14 PIN:1 IRQ:30
- [ 0.136000] Switching to clocksource MIPS
- [ 0.144000] NET: Registered protocol family 2
- [ 0.152000] IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
- [ 0.156000] TCP established hash table entries: 2048 (order: 2, 16384 bytes)
- [ 0.164000] TCP bind hash table entries: 2048 (order: 1, 8192 bytes)
- [ 0.172000] TCP: Hash tables configured (established 2048 bind 2048)
- [ 0.176000] TCP reno registered
- [ 0.180000] UDP hash table entries: 256 (order: 0, 4096 bytes)
- [ 0.188000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
- [ 0.192000] NET: Registered protocol family 1
- [ 0.200000] gptu: totally 6 16-bit timers/counters
- [ 0.204000] gptu: misc_register on minor 63
- [ 0.208000] gptu: succeeded to request irq 126
- [ 0.212000] gptu: succeeded to request irq 127
- [ 0.216000] gptu: succeeded to request irq 128
- [ 0.220000] gptu: succeeded to request irq 129
- [ 0.224000] gptu: succeeded to request irq 130
- [ 0.232000] gptu: succeeded to request irq 131
- [ 0.240000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
- [ 0.244000] JFFS2 version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY
- ) (c) 2001-2006 Red Hat, Inc.
- [ 0.256000] msgmni has been set to 120
- [ 0.260000] io scheduler noop registered
- [ 0.264000] io scheduler deadline registered (default)
- [ 0.268000] ltq_asc.1: ttyLTQ1 at MMIO 0x1e100c00 (irq = 112) is a ltq_asc
- [ 0.276000] console [ttyLTQ1] enabled, bootconsole disabled
- [ 0.276000] console [ttyLTQ1] enabled, bootconsole disabled
- [ 0.292000] ltq_nor: Found 1 x16 devices at 0x0 in 16-bit bank. Manufacturer
- ID 0x0000c2 Chip ID 0x0022a8
- [ 0.300000] Amd/Fujitsu Extended Query Table at 0x0040
- [ 0.304000] Amd/Fujitsu Extended Query version 1.1.
- [ 0.308000] number of CFI chips: 1
- [ 0.312000] Creating 4 MTD partitions on "ltq_nor":
- [ 0.316000] 0x000000000000-0x000000010000 : "uboot"
- [ 0.324000] 0x000000010000-0x000000020000 : "uboot_env"
- [ 0.332000] 0x000000020000-0x0000003f0000 : "linux"
- [ 0.340000] found squashfs behind kernel
- [ 0.340000] Creating 2 MTD partitions on "ltq_nor":
- [ 0.344000] 0x000000020000-0x00000010bb3d : "kernel"
- [ 0.352000] mtd: partition "kernel" must either start or end on erase block b
- oundary or be smaller than an erase block -- forcing read-only
- [ 0.364000] 0x00000010bb3d-0x0000003f0000 : "rootfs"
- [ 0.368000] mtd: partition "rootfs" must either start or end on erase block b
- oundary or be smaller than an erase block -- forcing read-only
- [ 0.384000] mtd: partition "rootfs" set to be root filesystem
- [ 0.388000] mtd: partition "rootfs_data" created automatically, ofs=3C0000, l
- en=30000
- [ 0.396000] 0x0000003c0000-0x0000003f0000 : "rootfs_data"
- [ 0.404000] 0x0000003f0000-0x000000400000 : "board_config"
- [ 0.416000] etop: invalid MAC, using random
- [ 0.432000] ltq_mii: probed
- [ 0.464000] Registering RTL8306SD switch with Chip ID: 0x5988, version: 0x000
- 0
- [ 0.468000] eth0: attached PHY [Realtek RTL8306S] (phy_addr=ltq_etop-fffffff:
- 00, irq=-1)
- [ 0.492000] TCP cubic registered
- [ 0.492000] NET: Registered protocol family 17
- [ 0.496000] 8021q: 802.1Q VLAN Support v[ 0.516000] VFS: Mounted root (squ
- ashfs filesystem) readonly on device 31:4.
- [ 0.524000] Freeing unused kernel memory: 172k freed
- - preinit -
- Press the [f] key and hit [enter] to enter failsafe mode
- - regular preinit -
- jffs2 not ready yet; using ramdisk
- - init -
- Please press Enter to activate this console. [ 9.776000] Compat-drivers backp
- ort release: compat-drivers-2012-09-04-2-gddac993
- [ 9.784000] Backport based on wireless-testing.git master-2012-09-07
- [ 9.788000] compat.git: wireless-testing.git
- [ 9.828000] cfg80211: Calling CRDA to update world regulatory domain
- [ 9.832000] cfg80211: World regulatory domain updated:
- [ 9.836000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gai
- n, max_eirp)
- [ 9.844000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 20
- 00 mBm)
- [ 9.852000] cfg80211: (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 20
- 00 mBm)
- [ 9.860000] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 20
- 00 mBm)
- [ 9.868000] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 20
- 00 mBm)
- [ 9.876000] cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 20
- 00 mBm)
- [ 10.776000] usbcore: registered new interface driver usbfs
- [ 10.780000] usbcore: registered new interface driver hub
- [ 10.788000] usbcore: registered new device driver usb
- [ 11.596000] PCI: Enabling device 0000:00:0e.0 (0000 -> 0002)
- [ 11.600000] ath5k 0000:00:0e.0: registered as 'phy0'
- [ 12.620000] ath5k: phy0: unable to init EEPROM
- [ 12.624000] ath5k: probe of 0000:00:0e.0 failed with error -5
- [ 13.272000] usbcore: registered new interface driver rt2500usb
- [ 13.424000] usbcore: registered new interface driver rt73usb
- [ 13.452000] usbcore: registered new interface driver rtl8187
- [ 13.512000] usbcore: registered new interface driver rt2800usb
- [ 13.540000] NET: Registered protocol family 8
- [ 13.544000] NET: Registered protocol family 20
- [ 13.588000] Button Hotplug driver version 0.4.1
- [ 13.632000] PPP generic driver version 2.4.2
- [ 14.076000] ip_tables: (C) 2000-2006 Netfilter Core Team
- [ 14.400000] NET: Registered protocol family 24
- [ 14.424000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
- [ 14.460000] nf_conntrack version 0.5.0 (969 buckets, 3876 max)
- [ 14.788000] IFX MEI Version 5.00.00
- [ 14.932000]
- [ 14.932000] Infineon CPE API Driver version: DSL CPE API V3.24.4.4
- [ 14.968000] ATM (A1) firmware version 1.0.19
- [ 14.972000] ifxmips_atm: ATM init succeed
- [ 15.004000] dwc_otg: version 2.60a 22-NOV-2006
- [ 15.612000] DWC_otg: Using DMA mode
- [ 15.612000] dwc_otg dwc_otg.0: DWC OTG Controller
- [ 15.616000] dwc_otg dwc_otg.0: new USB bus registered, assigned bus number 1
- [ 15.624000] dwc_otg dwc_otg.0: irq 62, io mem 0xffffffffbe101000
- [ 15.632000] DWC_otg: Init: Port Power? op_state=1
- [ 15.636000] DWC_otg: Init: Power Port (0)
- [ 15.640000] hub 1-0:1.0: USB hub found
- [ 15.644000] hub 1-0:1.0: 1 port detected
- [ 15.672000] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
- [ 15.796000] DISCONNECTED PORT
- [ 15.800000] uhci_hcd: USB Universal Host Controller Interface driver
- [ 15.956000] gpio-keys-polled gpio-keys-polled: unable to claim gpio 30, err=-
- 16
- [ 15.964000] gpio-keys-polled: probe of gpio-keys-polled failed with error -16
- [ 22.776000] device eth0 entered promiscuous mode
- [ 22.780000] br-lan: port 1(eth0) entered forwarding state
- [ 22.784000] br-lan: port 1(eth0) entered forwarding state
- [ 24.788000] br-lan: port 1(eth0) entered forwarding state
- BusyBox v1.19.4 (2013-04-16 01:21:14 CEST) built-in shell (ash)
- Enter 'help' for a list of built-in commands.
- _______ ________ __
- | |.-----.-----.-----.| | | |.----.| |_
- | - || _ | -__| || | | || _|| _|
- |_______|| __|_____|__|__||________||__| |____|
- |__| W I R E L E S S F R E E D O M
- -----------------------------------------------------
- ATTITUDE ADJUSTMENT (Attitude Adjustment, r36088)
- -----------------------------------------------------
- * 1/4 oz Vodka Pour all ingredients into mixing
- * 1/4 oz Gin tin with ice, strain into glass.
- * 1/4 oz Amaretto
- * 1/4 oz Triple sec
- * 1/4 oz Peach schnapps
- * 1/4 oz Sour mix
- * 1 splash Cranberry juice
- -----------------------------------------------------
Advertisement
Add Comment
Please, Sign In to add comment
Advertisement