API tools faq
paste
Advertisement
Guest User

Asus RT-AC51U - OpenWRT Boot process rootfs - Francis

a guest
Sep 27th, 2015
406
0
Never
Add comment
Not a member of Pastebin yet? Sign Up, it unlocks many cool features!
text 7.81 KB | None | 0 0
raw download clone embed print report
  1. U-Boot 1.1.3 (Nov 7 2013 - 17:33:35)
  2.  
  3. RT-AC51U bootloader version: 1.0.0.0
  4. Board: Ralink APSoC DRAM: 64 MB
  5. ASUS RT-AC51U gpio init : wps / reset pin
  6. enable ephy clock...done. rf reg 29 = 5
  7. SSC enabled. swing=5000, upperbound=0
  8. ******************************
  9. Software System Reset Occurred
  10. ******************************
  11. Ralink SPI flash driver, SPI clock: 48MHz
  12. spi device id: ef 40 18 0 0 (40180000)
  13. find flash: W25Q128FV
  14. raspi_read: from:30000 len:1000
  15. Maximum malloc length: 1024 KBytes
  16. mem_malloc_start/brk/end: 0x83eaf000/83eb1000/83fb0000
  17. *** Warning - bad CRC, using default environment
  18.  
  19. ============================================
  20. Ralink UBoot Version: 4.1.1.0
  21. --------------------------------------------
  22. ASIC 7620_MP (Port5<->None)
  23. DRAM component: 512 Mbits DDR, width 16
  24. DRAM bus: 16 bit
  25. Total memory: 64 MBytes
  26. Flash component: SPI Flash
  27. Date:Nov 7 2013 Time:17:33:35
  28. ============================================
  29. icache: sets:512, ways:4, linesz:32 ,total:65536
  30. dcache: sets:256, ways:4, linesz:32 ,total:32768
  31.  
  32. Please choose the operation:
  33. 0: Load System code then write to Flash via Serial.
  34. 1: Load System code to SDRAM via TFTP.
  35. 2: Load System code then write to Flash via TFTP.
  36. 3: Boot System code via Flash (default).
  37. 4: Entr boot command line interface.
  38. 5: Load Boot Loader code to SDRAM via Serial.
  39. 7: Load Boot Loader code then write to Flash via Serial.
  40. 8: Load Boot Loader code to SDRAM via TFTP.
  41. 9: Load Boot Loader code then write to Flash via TFTP.
  42. 0
  43.  
  44. 3: System Boot System code via Flash.
  45. raspi_read: from:4018a len:4
  46.  
  47. RT-AC51U bootloader version: 1.0.0.0
  48. raspi_read: from:40004 len:6
  49. MAC Address: 1C:B7:2C:7B:42:70
  50. raspi_read: from:40004 len:6
  51.  
  52. ## Checking 1st firmware at bc050000 ...
  53. raspi_read: from:50000 len:40
  54. Image Name:
  55. Image Type: MIPS Linux Kernel Image (lzma compressed)
  56. Data Size: 3095762 Bytes = 3 MB
  57. Load Address: 80000000
  58. Entry Point: 8000c150
  59. raspi_read: from:50040 len:2f3cd2
  60. Verifying Checksum ... OK
  61. Uncompressing Kernel Image ... OK
  62. ## Giving linux ramsize: 67108864 (64 MB)
  63.  
  64. Starting kernel ...
  65.  
  66. [ 0.000000] Linux version 3.18.21 (vico@Vico-OpenWRT) (gcc version 4.8.3 (OpenWrt/Linaro GCC 4.8-2014.04 r46832) ) #1 Sun Sep 27 12:53:50 CEST 2015
  67. [ 0.000000] Board has DDR2
  68. [ 0.000000] Analog PMU set to hw control
  69. [ 0.000000] Digital PMU set to hw control
  70. [ 0.000000] SoC Type: MediaTek MT7620A ver:2 eco:6
  71. [ 0.000000] bootconsole [early0] enabled
  72. [ 0.000000] CPU0 revision is: 00019650 (MIPS 24KEc)
  73. [ 0.000000] MIPS: machine is Ralink MT7620A evaluation board
  74. [ 0.000000] Determined physical RAM map:
  75. [ 0.000000] memory: 04000000 @ 00000000 (usable)
  76. [ 0.000000] Initrd not found or empty - disabling initrd
  77. [ 0.000000] Initmem setup node 0 [mem 0x00000000-0x03ffffff]
  78. [ 0.000000] Kernel command line: console=ttyS0,57600 rootfstype=squashfs,jffs2
  79. [ 0.000000] PID hash table entries: 256 (order: -2, 1024 bytes)
  80. [ 0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
  81. [ 0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
  82. [ 0.000000] Writing ErrCtl register=0004f7f0
  83. [ 0.000000] Readback ErrCtl register=0004f7f0
  84. [ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
  85. [ 0.000000] NR_IRQS:256
  86. [ 0.000000] CPU Clock: 580MHz
  87. [ 0.000000] systick: running - mult: 214748, shift: 32
  88. [ 0.000000] Calibrating delay loop... 383.38 BogoMIPS (lpj=1916928)
  89. [ 0.060000] pid_max: default: 32768 minimum: 301
  90. [ 0.060000] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
  91. [ 0.070000] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
  92. [ 0.070000] pinctrl core: initialized pinctrl subsystem
  93. [ 0.080000] NET: Registered protocol family 16
  94. [ 0.340000] PCI host bridge /pcie@10140000 ranges:
  95. [ 0.340000] MEM 0x0000000020000000..0x000000002fffffff
  96. [ 0.350000] IO 0x0000000010160000..0x000000001016ffff
  97. [ 0.360000] rt2880_gpio 10000600.gpio: registering 24 gpios
  98. [ 0.370000] rt2880_gpio 10000600.gpio: registering 24 irq handlers
  99. [ 0.370000] PCI host bridge to bus 0000:00
  100. [ 0.380000] pci_bus 0000:00: root bus resource [mem 0x20000000-0x2fffffff]
  101. [ 0.380000] pci_bus 0000:00: root bus resource [io 0xffffffff]
  102. [ 0.390000] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff]
  103. [ 0.390000] pci 0000:00:00.0: BAR 0: no space for [mem size 0x80000000]
  104. [ 0.400000] pci 0000:00:00.0: BAR 0: failed to assign [mem size 0x80000000]
  105. [ 0.400000] pci 0000:00:00.0: BAR 8: assigned [mem 0x20000000-0x201fffff]
  106. [ 0.410000] pci 0000:00:00.0: BAR 1: assigned [mem 0x20200000-0x2020ffff]
  107. [ 0.410000] pci 0000:01:00.0: BAR 0: assigned [mem 0x20000000-0x200fffff]
  108. [ 0.420000] pci 0000:01:00.1: BAR 0: assigned [mem 0x20100000-0x201fffff]
  109. [ 0.420000] pci 0000:00:00.0: PCI bridge to [bus 01]
  110. [ 0.430000] pci 0000:00:00.0: bridge window [mem 0x20000000-0x201fffff]
  111. [ 0.430000] pci 0000:00:00.0: card - bus=0x0, slot = 0x0 irq=0
  112. [ 0.440000] pci 0000:01:00.0: card - bus=0x1, slot = 0x0 irq=4
  113. [ 0.440000] pci 0000:01:00.1: card - bus=0x1, slot = 0x0 irq=4
  114. [ 0.450000] Switched to clocksource systick
  115. [ 0.450000] NET: Registered protocol family 2
  116. [ 0.460000] TCP established hash table entries: 1024 (order: 0, 4096 bytes)
  117. [ 0.460000] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
  118. [ 0.470000] TCP: Hash tables configured (established 1024 bind 1024)
  119. [ 0.470000] TCP: reno registered
  120. [ 0.480000] UDP hash table entries: 256 (order: 0, 4096 bytes)
  121. [ 0.480000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
  122. [ 0.490000] NET: Registered protocol family 1
  123. [ 0.490000] rt-timer 10000100.timer: maximum frequency is 2441Hz
  124. [ 0.500000] futex hash table entries: 256 (order: -1, 3072 bytes)
  125. [ 0.530000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
  126. [ 0.530000] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
  127. [ 0.540000] msgmni has been set to 119
  128. [ 0.550000] io scheduler noop registered
  129. [ 0.550000] io scheduler deadline registered (default)
  130. [ 0.560000] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
  131. [ 0.570000] console [ttyS0] disabled
  132. [ 0.570000] 10000c00.uartlite: ttyS0 at MMIO 0x10000c00 (irq = 20, base_baud = 2500000) is a 16550A
  133. [ 0.660000] console [ttyS0] enabled
  134. [ 0.670000] bootconsole [early0] disabled
  135. [ 0.670000] bootconsole [early0] disabled
  136. [ 0.690000] spi spi32766.0: setup: requested speed is too low 1000000 Hz
  137. [ 0.710000] spi-rt2880 10000b00.spi: can't setup spi32766.0, status -22
  138. [ 0.720000] spi_master spi32766: spi_device register error /palmbus@10000000/spi@b00/m25p80@0
  139. [ 0.740000] gsw: setting port4 to ephy mode
  140. [ 0.750000] ralink_soc_eth 10100000.ethernet eth0 (uninitialized): port 0 link up (100Mbps/Full duplex)
  141. [ 0.750000] ralink_soc_eth 10100000.ethernet eth0 (uninitialized): port 1 link up (100Mbps/Full duplex)
  142. [ 0.790000] ralink_soc_eth 10100000.ethernet: generated random MAC address aa:c4:18:64:b0:62
  143. [ 0.800000] ralink_soc_eth 10100000.ethernet: loaded mt7620 driver
  144. [ 0.820000] ralink_soc_eth 10100000.ethernet eth0: ralink at 0xb0100000, irq 5
  145. [ 0.830000] rt2880_wdt 10000120.watchdog: Initialized
  146. [ 0.840000] TCP: cubic registered
  147. [ 0.850000] NET: Registered protocol family 10
  148. [ 0.860000] NET: Registered protocol family 17
  149. [ 0.870000] bridge: automatic filtering via arp/ip/ip6tables has been deprecated. Update your scripts to load br_netfilter if you need this.
  150. [ 0.900000] 8021q: 802.1Q VLAN Support v1.8
  151. [ 0.910000] Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(0,0)
  152. [ 0.910000] ---[ end Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(0,0)
Advertisement
Add Comment
Please, Sign In to add comment
Advertisement
Public Pastes
Advertisement
We use cookies for various purposes including analytics. By continuing to use Pastebin, you agree to our use of cookies as described in the Cookies Policy.  OK, I Understand
Not a member of Pastebin yet?
Sign Up, it unlocks many cool features!