Advertisement
Not a member of Pastebin yet?
Sign Up,
it unlocks many cool features!
- [ 0.000000] Linux version 4.4.3 (christopher@Ubuntu-xw4600) (gcc version 5.3.0 (OpenWrt GCC 5.3.0 r48886) ) #2 Thu Mar 3 18:41:40 UTC 2016
- [ 0.000000] SoC: xRX200 rev 1.2
- [ 0.000000] bootconsole [early0] enabled
- [ 0.000000] CPU0 revision is: 00019556 (MIPS 34Kc)
- [ 0.000000] MIPS: machine is BTHOMEHUBV5A - BT Home Hub 5A
- [ 0.000000] Determined physical RAM map:
- [ 0.000000] memory: 08000000 @ 00000000 (usable)
- [ 0.000000] Initrd not found or empty - disabling initrd
- [ 0.000000] Zone ranges:
- [ 0.000000] Normal [mem 0x0000000000000000-0x0000000007ffffff]
- [ 0.000000] Movable zone start for each node
- [ 0.000000] Early memory node ranges
- [ 0.000000] node 0: [mem 0x0000000000000000-0x0000000007ffffff]
- [ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x0000000007ffffff]
- [ 0.000000] On node 0 totalpages: 32768
- [ 0.000000] free_area_init_node: node 0, pgdat 804da390, node_mem_map 81009240
- [ 0.000000] Normal zone: 256 pages used for memmap
- [ 0.000000] Normal zone: 0 pages reserved
- [ 0.000000] Normal zone: 32768 pages, LIFO batch:7
- [ 0.000000] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
- [ 0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
- [ 0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
- [ 0.000000] pcpu-alloc: [0] 0
- [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 32512
- [ 0.000000] Kernel command line: console=ttyLTQ0,115200 init=/etc/preinit
- [ 0.000000] PID hash table entries: 512 (order: -1, 2048 bytes)
- [ 0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
- [ 0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
- [ 0.000000] Writing ErrCtl register=00028880
- [ 0.000000] Readback ErrCtl register=00028880
- [ 0.000000] Memory: 124328K/131072K available (3776K kernel code, 167K rwdata, 1144K rodata, 208K init, 211K bss, 6744K reserved, 0K cma-reserved)
- [ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
- [ 0.000000] NR_IRQS:256
- [ 0.000000] CPU Clock: 500MHz
- [ 0.000000] clocksource: MIPS: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041786 ns
- [ 0.000011] sched_clock: 32 bits at 250MHz, resolution 4ns, wraps every 8589934590ns
- [ 0.007855] Calibrating delay loop... 332.54 BogoMIPS (lpj=665088)
- [ 0.042317] pid_max: default: 32768 minimum: 301
- [ 0.047152] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
- [ 0.053724] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
- [ 0.066635] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns
- [ 0.076413] pinctrl core: initialized pinctrl subsystem
- [ 0.082239] NET: Registered protocol family 16
- [ 0.091294] pinctrl-xway 1e100b10.pinmux: Init done
- [ 0.096785] dma-xway 1e104100.dma: Init done - hw rev: 7, ports: 7, channels: 28
- [ 0.206773] dcdc-xrx200 1f106a00.dcdc: Core Voltage : 1016 mV
- [ 0.221806] PCI host bridge /fpi@10000000/pci@E105400 ranges:
- [ 0.227445] MEM 0x0000000018000000..0x0000000019ffffff
- [ 0.232701] IO 0x000000001ae00000..0x000000001affffff
- [ 0.356151] ath9k,eeprom ath9k_eep: failed to load eeprom address
- [ 0.376065] usbcore: registered new interface driver usbfs
- [ 0.381544] usbcore: registered new interface driver hub
- [ 0.386905] usbcore: registered new device driver usb
- [ 0.392303] PCI host bridge to bus 0000:00
- [ 0.396293] pci_bus 0000:00: root bus resource [mem 0x18000000-0x19ffffff]
- [ 0.403202] pci_bus 0000:00: root bus resource [io 0xffffffff]
- [ 0.409195] pci_bus 0000:00: root bus resource [??? 0x00000000 flags 0x0]
- [ 0.416047] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff]
- [ 0.424099] pci 0000:00:0e.0: [168c:ff1d] type 00 class 0x020000
- [ 0.424168] pci 0000:00:0e.0: reg 0x10: [mem 0x00000000-0x0000ffff]
- [ 0.424568] pci_bus 0000:00: busn_res: [bus 00-ff] end is updated to 00
- [ 0.424611] pci 0000:00:0e.0: BAR 0: assigned [mem 0x18000000-0x1800ffff]
- [ 0.431448] PCI host bridge to bus 0000:01
- [ 0.435441] pci_bus 0000:01: root bus resource [mem 0x1c000000-0x1cffffff]
- [ 0.442356] pci_bus 0000:01: root bus resource [io 0x1d800000-0x1d8fffff]
- [ 0.449301] pci_bus 0000:01: root bus resource [??? 0x00000000 flags 0x0]
- [ 0.456156] pci_bus 0000:01: No busn resource found for root bus, will use [bus 01-ff]
- [ 0.464183] pci 0000:01:00.0: [1bef:0011] type 01 class 0x060000
- [ 0.464217] ifx_pcie_rc_class_early_fixup: fixed pcie host bridge to pci-pci bridge
- [ 0.481948] pci 0000:01:00.0: PME# supported from D0 D3hot
- [ 0.482252] pci 0000:01:00.0: bridge configuration invalid ([bus 02-00]), reconfiguring
- [ 0.490367] pci 0000:02:00.0: [168c:003c] type 00 class 0x028000
- [ 0.490453] pci 0000:02:00.0: reg 0x10: [mem 0x00000000-0x001fffff 64bit]
- [ 0.490522] pci 0000:02:00.0: reg 0x30: [mem 0x00000000-0x0000ffff pref]
- [ 0.490623] pci 0000:02:00.0: supports D1 D2
- [ 0.490905] pci_bus 0000:02: busn_res: [bus 02-ff] end is updated to 02
- [ 0.490943] pci_bus 0000:01: busn_res: [bus 01-ff] end is updated to 02
- [ 0.490997] pci 0000:01:00.0: BAR 8: assigned [mem 0x1c000000-0x1c1fffff]
- [ 0.497671] pci 0000:01:00.0: BAR 9: assigned [mem 0x1c200000-0x1c2fffff pref]
- [ 0.504942] pci 0000:02:00.0: BAR 0: assigned [mem 0x1c000000-0x1c1fffff 64bit]
- [ 0.512338] pci 0000:02:00.0: BAR 6: assigned [mem 0x1c200000-0x1c20ffff pref]
- [ 0.519603] pci 0000:01:00.0: PCI bridge to [bus 02]
- [ 0.524636] pci 0000:01:00.0: bridge window [mem 0x1c000000-0x1c1fffff]
- [ 0.531492] pci 0000:01:00.0: bridge window [mem 0x1c200000-0x1c2fffff pref]
- [ 0.538856] ifx_pcie_bios_map_irq port 0 dev 0000:01:00.0 slot 0 pin 1
- [ 0.545466] ifx_pcie_bios_map_irq dev 0000:01:00.0 irq 144 assigned
- [ 0.551809] ifx_pcie_bios_map_irq port 0 dev 0000:02:00.0 slot 0 pin 1
- [ 0.558476] ifx_pcie_bios_map_irq dev 0000:02:00.0 irq 144 assigned
- [ 0.565784] clocksource: Switched to clocksource MIPS
- [ 0.572322] NET: Registered protocol family 2
- [ 0.577440] TCP established hash table entries: 1024 (order: 0, 4096 bytes)
- [ 0.584333] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
- [ 0.590711] TCP: Hash tables configured (established 1024 bind 1024)
- [ 0.597218] UDP hash table entries: 256 (order: 0, 4096 bytes)
- [ 0.603066] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
- [ 0.609632] NET: Registered protocol family 1
- [ 0.614001] PCI: CLS 0 bytes, default 32
- [ 0.614402] gptu: totally 6 16-bit timers/counters
- [ 0.619224] gptu: misc_register on minor 63
- [ 0.623336] gptu: succeeded to request irq 126
- [ 0.627828] gptu: succeeded to request irq 127
- [ 0.632342] gptu: succeeded to request irq 128
- [ 0.636856] gptu: succeeded to request irq 129
- [ 0.641369] gptu: succeeded to request irq 130
- [ 0.645885] gptu: succeeded to request irq 131
- [ 0.651262] phy-xrx200 gphy-xrx200: requesting lantiq/vr9_phy11g_a2x.bin
- [ 0.658586] phy-xrx200 gphy-xrx200: booting GPHY0 firmware at 7960000
- [ 0.664908] phy-xrx200 gphy-xrx200: booting GPHY1 firmware at 7960000
- [ 0.772406] futex hash table entries: 256 (order: -1, 3072 bytes)
- [ 0.804787] squashfs: version 4.0 (2009/01/31) Phillip Lougher
- [ 0.810534] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
- [ 0.823817] io scheduler noop registered
- [ 0.827649] io scheduler deadline registered (default)
- [ 0.833490] 1e100c00.serial: ttyLTQ0 at MMIO 0x1e100c00 (irq = 112, base_baud = 0) is a lantiq,asc
- [ 0.842390] console [ttyLTQ0] enabled
- [ 0.849716] bootconsole [early0] disabled
- [ 0.861207] nand: device found, Manufacturer ID: 0x01, Chip ID: 0xf1
- [ 0.866104] nand: AMD/Spansion S34ML01G1
- [ 0.870023] nand: 128 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64
- [ 0.877670] Scanning device for bad blocks
- [ 1.029854] 5 ofpart partitions found on MTD device 14000000.nand-parts
- [ 1.035034] Creating 5 MTD partitions on "14000000.nand-parts":
- [ 1.040956] 0x000000000000-0x000000040000 : "u-boot"
- [ 1.047672] 0x000000040000-0x000000080000 : "uboot-env"
- [ 1.053505] 0x000000080000-0x0000000a0000 : "caldata"
- [ 1.059267] 0x0000000a0000-0x0000002a0000 : "kernel"
- [ 1.064864] 0x0000002a0000-0x000008000000 : "ubi"
- [ 1.173102] libphy: lantiq,xrx200-mdio: probed
- [ 1.246516] eth0: attached PHY [Lantiq XWAY PEF7071] (phy_addr=0:00, irq=-1)
- [ 1.314489] eth0: attached PHY [Lantiq XWAY PEF7071] (phy_addr=0:01, irq=-1)
- [ 1.382475] eth0: attached PHY [Lantiq XWAY VR9 GPHY 11G v1.4] (phy_addr=0:11, irq=-1)
- [ 1.450474] eth0: attached PHY [Lantiq XWAY VR9 GPHY 11G v1.4] (phy_addr=0:13, irq=-1)
- [ 1.522499] eth1: attached PHY [Lantiq XWAY PEF7071] (phy_addr=0:05, irq=-1)
- [ 1.529382] wdt 1f8803f0.watchdog: Init done
- [ 1.535939] NET: Registered protocol family 10
- [ 1.545083] NET: Registered protocol family 17
- [ 1.548245] bridge: automatic filtering via arp/ip/ip6tables has been deprecated. Update your scripts to load br_netfilter if you need this.
- [ 1.560753] 8021q: 802.1Q VLAN Support v1.8
- [ 1.569010] ath9k,eeprom ath9k_eep: pci slot: 14
- [ 1.572203] pci 0000:00:0e.0: fixup device configuration
- [ 1.579128] pci 0000:00:0e.0: fixup info: [168c:002d] revision 01 class 0x028000
- [ 1.585114] ath9k,eeprom ath9k_eep: loaded ath9k eeprom
- [ 1.594238] UBI: auto-attach mtd4
- [ 1.595925] ubi0: attaching mtd4
- [ 2.234792] ubi0: scanning is finished
- [ 2.276252] ubi0: attached mtd4 (name "ubi", size 125 MiB)
- [ 2.280341] ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 129024 bytes
- [ 2.287183] ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 512
- [ 2.293883] ubi0: VID header offset: 512 (aligned 512), data offset: 2048
- [ 2.300671] ubi0: good PEBs: 1003, bad PEBs: 0, corrupted PEBs: 0
- [ 2.306765] ubi0: user volume: 1, internal volumes: 1, max. volumes count: 128
- [ 2.314002] ubi0: max/mean erase counter: 8/5, WL threshold: 4096, image sequence number: 926466262
- [ 2.323045] ubi0: available PEBs: 0, total reserved PEBs: 1003, PEBs reserved for bad PEB handling: 20
- [ 2.332537] ubi0: background thread "ubi_bgt0d" started, PID 309
- [ 2.444545] UBIFS (ubi0:0): background thread "ubifs_bgt0_0" started, PID 311
- [ 2.550734] UBIFS (ubi0:0): recovery needed
- [ 2.889181] UBIFS (ubi0:0): recovery completed
- [ 2.892317] UBIFS (ubi0:0): UBIFS: mounted UBI device 0, volume 0, name "rootfs"
- [ 2.899609] UBIFS (ubi0:0): LEB size: 129024 bytes (126 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
- [ 2.909518] UBIFS (ubi0:0): FS size: 124895232 bytes (119 MiB, 968 LEBs), journal size 9033728 bytes (8 MiB, 71 LEBs)
- [ 2.920130] UBIFS (ubi0:0): reserved for root: 0 bytes (0 KiB)
- [ 2.925970] UBIFS (ubi0:0): media format: w4/r0 (latest is w4/r0), UUID CE6D1A07-5244-4583-A9C2-4DF772DF74A1, small LPT model
- [ 2.938914] VFS: Mounted root (ubifs filesystem) on device 0:11.
- [ 2.944170] Freeing unused kernel memory: 208K (804fc000 - 80530000)
- [ 3.295328] init: Console is alive
- [ 3.297563] init: - watchdog -
- [ 3.807791] dwc2 1e101000.ifxhcd: requested GPIO 495
- [ 3.811388] dwc2 1e101000.ifxhcd: Configuration mismatch. Forcing host mode
- [ 4.673962] dwc2 1e101000.ifxhcd: DWC OTG Controller
- [ 4.677528] dwc2 1e101000.ifxhcd: new USB bus registered, assigned bus number 1
- [ 4.684871] dwc2 1e101000.ifxhcd: irq 62, io mem 0x00000000
- [ 4.690394] dwc2 1e101000.ifxhcd: Hardware does not support descriptor DMA mode -
- [ 4.697835] dwc2 1e101000.ifxhcd: falling back to buffer DMA mode.
- [ 4.705204] hub 1-0:1.0: USB hub found
- [ 4.708240] hub 1-0:1.0: 1 port detected
- [ 5.319457] init: - preinit -
- [ 5.610925] random: procd urandom read with 19 bits of entropy available
- [ 6.329926] eth0: port 1 got link
- [ 8.749526] mount_root: mounting /dev/root
- [ 8.766927] procd: - early -
- [ 8.768506] procd: - watchdog -
- [ 9.343813] procd: - ubus -
- [ 10.366583] procd: - init -
- [ 11.155778] IFXOS, Version 1.5.19 (c) Copyright 2009, Lantiq Deutschland GmbH
- [ 11.187964] NET: Registered protocol family 8
- [ 11.190923] NET: Registered protocol family 20
- [ 11.216129] PPP generic driver version 2.4.2
- [ 11.233237] ip6_tables: (C) 2000-2006 Netfilter Core Team
- [ 11.339589] Lantiq (VRX) DSL CPE MEI driver, version 1.4.8.5, (c) 2013 Lantiq Deutschland GmbH
- [ 11.339589]
- [ 11.339589] Lantiq CPE API Driver version: DSL CPE API V4.16.6.3
- [ 11.445665]
- [ 11.445665] Predefined debug level: 3
- [ 11.454516] Loading modules backported from Linux version v4.4-rc5-1913-gc8fdf68
- [ 11.460524] Backport generated by backports.git backports-20151218-0-g2f58d9d
- [ 12.151085] PCI: Enabling device 0000:01:00.0 (0000 -> 0002)
- [ 12.155419] PCI: Enabling device 0000:02:00.0 (0000 -> 0002)
- [ 12.161505] ath10k_pci 0000:02:00.0: pci irq legacy interrupts 0 irq_mode 0 reset_mode 0
- [ 12.579815] ath10k_pci 0000:02:00.0: qca988x hw2.0 target 0x4100016c chip_id 0x043202ff sub 0000:0000
- [ 12.587670] ath10k_pci 0000:02:00.0: kconfig debug 0 debugfs 1 tracing 0 dfs 1 testmode 1
- [ 12.603394] ath10k_pci 0000:02:00.0: firmware ver 10.2.4.97 api 5 features no-p2p crc32 f91e34f2
- [ 12.651008] ath10k_pci 0000:02:00.0: Direct firmware load for ath10k/QCA988X/hw2.0/board-2.bin failed with error -2
- [ 12.660055] ath10k_pci 0000:02:00.0: Falling back to user helper
- [ 12.717298] firmware ath10k!QCA988X!hw2.0!board-2.bin: firmware_loading_store: map pages failed
- [ 12.726650] ath10k_pci 0000:02:00.0: board_file api 1 bmi_id N/A crc32 bebc7c08
- [ 13.812850] ath10k_pci 0000:02:00.0: htt-ver 2.1 wmi-op 5 htt-op 2 cal file max-sta 128 raw 0 hwcrypto 1
- [ 13.909287] ath: EEPROM regdomain: 0x833a
- [ 13.909310] ath: EEPROM indicates we should expect a country code
- [ 13.909330] ath: doing EEPROM country->regdmn map search
- [ 13.909345] ath: country maps to regdmn code: 0x37
- [ 13.909358] ath: Country alpha2 being used: GB
- [ 13.909369] ath: Regpair used: 0x37
- [ 14.209663] ip_tables: (C) 2000-2006 Netfilter Core Team
- [ 14.228414] Infineon Technologies DEU driver version 2.0.0
- [ 14.234176] IFX DEU DES initialized (multiblock).
- [ 14.238388] IFX DEU AES initialized (multiblock).
- [ 14.242548] IFX DEU ARC4 initialized (multiblock).
- [ 14.247183] IFX DEU SHA1 initialized.
- [ 14.250790] IFX DEU MD5 initialized.
- [ 14.254516] IFX DEU SHA1_HMAC initialized.
- [ 14.258502] IFX DEU MD5_HMAC initialized.
- [ 14.301901] nf_conntrack version 0.5.0 (1945 buckets, 7780 max)
- [ 14.329251] NET: Registered protocol family 24
- [ 14.353379] xt_time: kernel timezone is -0000
- [ 14.463124] PCI: Enabling device 0000:00:0e.0 (0000 -> 0002)
- [ 14.473162] ath: phy1: Ignoring endianness difference in EEPROM magic bytes.
- [ 14.480585] ath: EEPROM regdomain: 0x833a
- [ 14.480603] ath: EEPROM indicates we should expect a country code
- [ 14.480624] ath: doing EEPROM country->regdmn map search
- [ 14.480638] ath: country maps to regdmn code: 0x37
- [ 14.480651] ath: Country alpha2 being used: GB
- [ 14.480662] ath: Regpair used: 0x37
- [ 14.497378] ieee80211 phy1: Selected rate control algorithm 'minstrel_ht'
- [ 14.500618] ieee80211 phy1: Atheros AR9287 Rev:2 mem=0xb8000000, irq=30
- [ 18.689843] PTM 1.0.27 PTM (E1) firmware version 0.30
- [ 18.693706] ifxmips_ptm: PTM init succeed
- [ 23.496680] device eth0.1 entered promiscuous mode
- [ 23.500235] device eth0 entered promiscuous mode
- [ 23.517054] br-lan: port 1(eth0.1) entered forwarding state
- [ 23.521284] br-lan: port 1(eth0.1) entered forwarding state
- [ 23.586143] IPv6: ADDRCONF(NETDEV_UP): ptm0: link is not ready
- [ 23.609192] IPv6: ADDRCONF(NETDEV_UP): ptm0.101: link is not ready
- [ 25.521794] br-lan: port 1(eth0.1) entered forwarding state
- [ 32.087270] random: nonblocking pool is initialized
- [ 58.889472] enter showtime
- [ 58.890846] IPv6: ADDRCONF(NETDEV_CHANGE): ptm0: link becomes ready
- [ 58.902090] enter showtime
- [ 58.917916] IPv6: ADDRCONF(NETDEV_CHANGE): ptm0.101: link becomes ready
- [ 60.690912] pppoe-wan: renamed from ppp0
- [ 89.111032] pppoe-wan: renamed from ppp0
- [24193.984976] IPv6: ADDRCONF(NETDEV_UP): wlan1: link is not ready
- [24193.997756] device wlan1 entered promiscuous mode
- [24194.077748] IPv6: ADDRCONF(NETDEV_CHANGE): wlan1: link becomes ready
- [24194.082927] br-lan: port 2(wlan1) entered forwarding state
- [24194.088273] br-lan: port 2(wlan1) entered forwarding state
- [24196.090522] br-lan: port 2(wlan1) entered forwarding state
- [24200.206985] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
- [24200.221277] device wlan0 entered promiscuous mode
- [24200.544465] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
- [24200.549703] br-lan: port 3(wlan0) entered forwarding state
- [24200.555050] br-lan: port 3(wlan0) entered forwarding state
- [24202.558382] br-lan: port 3(wlan0) entered forwarding state
Advertisement
Add Comment
Please, Sign In to add comment
Advertisement