Advertisement
Not a member of Pastebin yet?
Sign Up,
it unlocks many cool features!
- [ 0.883804] ata1: SATA max UDMA/133 mmio [mem 0x01c18000-0x01c18fff] port 0x100 irq 23
- [ 0.892313] CAN device driver interface
- [ 0.898543] sun4i-emac 1c0b000.ethernet: eth0: at e00b2000, IRQ 18 MAC: 12:34:56:78:99:aa
- [ 0.907123] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
- [ 0.913648] ehci-platform: EHCI generic platform driver
- [ 0.919155] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
- [ 0.925347] ohci-platform: OHCI generic platform driver
- [ 0.931990] sunxi-rtc 1c20d00.rtc: rtc core: registered rtc-sunxi as rtc0
- [ 0.938826] sunxi-rtc 1c20d00.rtc: RTC enabled
- [ 0.943348] i2c /dev entries driver
- [ 0.947766] axp20x 0-0034: AXP20x variant AXP209 found
- [ 0.960259] input: axp20x-pek as /devices/platform/soc@01c00000/1c2ac00.i2c/i2c-0/0-0034/axp20x-pek/input/input0
- [ 0.970630] axp20x-regulator axp20x-regulator: regulators node not found
- [ 0.979874] axp20x 0-0034: AXP20X driver loaded
- [ 0.985107] sunxi-wdt 1c20c90.watchdog: Watchdog enabled (timeout=16 sec, nowayout=0)
- [ 0.993594] sunxi-mmc 1c0f000.mmc: No vqmmc regulator found
- [ 0.999565] sunxi-mmc 1c0f000.mmc: Got CD GPIO
- [ 1.037040] sunxi-mmc 1c0f000.mmc: base:0xe00bc000 irq:19
- [ 1.043267] sun4i-ss 1c15000.crypto-engine: no reset control found
- [ 1.049608] sun4i-ss 1c15000.crypto-engine: Die ID 7
- [ 1.056189] usbcore: registered new interface driver usbhid
- [ 1.061820] usbhid: USB HID core driver
- [ 1.066474] NET: Registered protocol family 17
- [ 1.070979] can: controller area network core (rev 20120528 abi 9)
- [ 1.077266] NET: Registered protocol family 29
- [ 1.081715] can: raw protocol (rev 20120528)
- [ 1.085986] can: broadcast manager protocol (rev 20120528 t)
- [ 1.091671] can: netlink gateway (rev 20130117) max_hops=1
- [ 1.097506] Key type dns_resolver registered
- [ 1.102761] Registering SWP/SWPB emulation handler
- [ 1.111934] libphy: sun4i_mii_bus: probed
- [ 1.144209] mmc0: host does not support reading read-only switch, assuming write-enable
- [ 1.152573] ehci-platform 1c14000.usb: EHCI Host Controller
- [ 1.158232] ehci-platform 1c14000.usb: new USB bus registered, assigned bus number 1
- [ 1.166113] ehci-platform 1c14000.usb: irq 20, io mem 0x01c14000
- [ 1.172320] mmc0: new high speed SDHC card at address 1234
- [ 1.178383] mmcblk0: mmc0:1234 SA16G 14.6 GiB
- [ 1.184596] mmcblk0: p1 p2 p3
- [ 1.188606] ehci-platform 1c14000.usb: USB 2.0 started, EHCI 1.00
- [ 1.195552] hub 1-0:1.0: USB hub found
- [ 1.199416] hub 1-0:1.0: 1 port detected
- [ 1.204017] ehci-platform 1c1c000.usb: EHCI Host Controller
- [ 1.209677] ehci-platform 1c1c000.usb: new USB bus registered, assigned bus number 2
- [ 1.217580] ehci-platform 1c1c000.usb: irq 24, io mem 0x01c1c000
- [ 1.236884] ehci-platform 1c1c000.usb: USB 2.0 started, EHCI 1.00
- [ 1.243794] hub 2-0:1.0: USB hub found
- [ 1.247631] hub 2-0:1.0: 1 port detected
- [ 1.252193] ohci-platform 1c14400.usb: Generic Platform OHCI controller
- [ 1.258888] ohci-platform 1c14400.usb: new USB bus registered, assigned bus number 3
- [ 1.266759] ohci-platform 1c14400.usb: irq 21, io mem 0x01c14400
- [ 1.286894] ata1: SATA link down (SStatus 0 SControl 300)
- [ 1.331677] hub 3-0:1.0: USB hub found
- [ 1.335467] hub 3-0:1.0: 1 port detected
- [ 1.340112] ohci-platform 1c1c400.usb: Generic Platform OHCI controller
- [ 1.346749] ohci-platform 1c1c400.usb: new USB bus registered, assigned bus number 4
- [ 1.354670] ohci-platform 1c1c400.usb: irq 25, io mem 0x01c1c400
- [ 1.421657] hub 4-0:1.0: USB hub found
- [ 1.425443] hub 4-0:1.0: 1 port detected
- [ 1.429961] sunxi-rtc 1c20d00.rtc: setting system clock to 2010-01-01 00:18:11 UTC (1262305091)
- [ 1.444537] sun4i-emac 1c0b000.ethernet eth0: could not find the PHY
- [ 1.450997] sun4i-emac 1c0b000.ethernet eth0: cannot probe MDIO bus
- [ 1.457295] IP-Config: Failed to open eth0
- [ 1.461388] IP-Config: Device `eth0' not found
Advertisement
Add Comment
Please, Sign In to add comment
Advertisement