Marvell>> ?
?       - alias for 'help'
SatR    - Sample At Reset sub-system

amp_boot- amp_boot - boot an AMP group

amp_config- Fully config an AMP group

amp_printenv- amp_printenv - print only AMP env variables

amp_verify- Verfiy AMP configuration

base    - print or set address offset
bdinfo  - print Board Info structure
bios    - BIOS command to set the DB configuration.

boot    - boot default, i.e., run 'bootcmd'
bootd   - boot default, i.e., run 'bootcmd'
bootelf - Boot from an ELF image in memory
bootm   - boot application image from memory
bootp   - boot image via network using BOOTP/TFTP protocol
bootvx  - Boot vxWorks from an ELF image
bubt    - bubt  - Burn an image on the Boot Nand Flash.

chpart  - change active partition
cmp     - memory compare
coninfo - print console devices and information
cp      - memory copy
crc32   - checksum calculation
date    - get/set/reset date & time
ddrPhyRead- ddrPhyRead - Read DDR PHY register

ddrPhyWrite- ddrPhyWrite - Write DDR PHY register

devinfo - devinfo handling commands
dhcp    - boot image via network using DHCP/TFTP protocol
diskboot- diskboot- boot from IDE device

dma     - dma   - Perform DMA using the XOR engine

echo    - echo args to console
editenv - edit environment variable
eeprom  - EEPROM sub-system
env     - environment handling commands
exit    - exit script
ext2load- load binary file from a Ext2 filesystem
ext2ls  - list files in a directory (default /)
false   - do nothing, unsuccessfully
fatinfo - print information about filesystem
fatload - load binary file from a dos filesystem
fatls   - list files in a directory (default /)
fsinfo  - print information about filesystems
fsload  - load binary file from a filesystem image
go      - start application at address 'addr'
help    - print command description/usage
i2c     - I2C sub-system
ide     - ide     - IDE sub-system

iminfo  - print header information for application image
imxtract- extract a part of a multi-image
ir      - ir    - reading and changing MV internal register values.

itest   - return true/false on integer compare
loadb   - load binary file over serial line (kermit mode)
loads   - load S-Record file over serial line
loadx   - load binary file over serial line (xmodem mode)
loady   - load binary file over serial line (ymodem mode)
loop    - infinite loop on address range
ls      - list files in a directory (default /)
map     - map   - Diasplay address decode windows

md      - memory display
me      - me    - PCI master enable

mfg     - mfg   - Diagnostic tools for MFG

mm      - memory modify (auto-incrementing address)
mmc     - MMC sub system
mmcinfo - display MMC info
mp      - mp    - map PCI BAR

mtdparts- define flash/nand partitions
mtest   - simple RAM read/write test
mw      - memory write (fill)
nand    - NAND sub-system
nboot   - boot from NAND device
nfs     - boot image via network using NFS protocol
nm      - memory modify (constant address)
pci     - list and access PCI Configuration Space
pciePhyRead- phyRead    - Read PCI-E Phy register

pciePhyWrite- pciePhyWrite      - Write PCI-E Phy register

phyRead - phyRead       - Read Phy register

phyWrite- phyWrite      - Write Phy register

ping    - send ICMP ECHO_REQUEST to network host
printenv- print environment variables
pxe     - commands to get and boot from pxe files
rcvr    - rcvr  - Satrt recovery process (Distress Beacon with TFTP server)

reset   - Perform RESET of the CPU
resetenv- resetenv      - earse environment sector to reset all variables to default.

run     - run commands in an environment variable
saveenv - save environment variables to persistent storage
scsi    - SCSI sub-system
scsiboot- boot from SCSI device
se      - se    - PCI Slave enable

senv    - senv handling commands
setdevinfo- set devinfo variables
setenv  - set environment variables
setsenv - set senv variables
sf      - SPI flash sub-system
sg      - sg    - scanning the PHYs status

showvar - print local hushshell variables
sleep   - delay execution for some time
source  - run script from memory
sp      - sp    - Scan PCI Interface [bus].

sspi    - SPI utility command
stage_boot- command to load script/image from different devices
        example: stage_boot hd_img pxe
switchCountersRead- switchCntPrint      - Read switch port counters.

switchPhyRegRead- - Read switch register

switchPhyRegWrite- - Write switch register

switchRegRead- switchRegRead    - Read switch register

switchRegWrite- switchRegWrite  - Write switch register

temp    - temp  - Display the device temprature.

tempCmd0- tempCmd - This command allocated for monitor extintion

tempCmd1- tempCmd - This command allocated for monitor extintion

tempCmd2- tempCmd - This command allocated for monitor extintion

tempCmd3- tempCmd - This command allocated for monitor extintion

test    - minimal test like /bin/sh
tftpboot- boot image via network using TFTP protocol
training- training      - prints the results of the DDR3 Training.

true    - do nothing, successfully
ts_report- ts_report    - report touch screen cooridate

ts_test - ts_test       - test touch screen

ubi     - ubi commands
ubifsload- load file from an UBIFS filesystem
ubifsls - list files in a directory
ubifsmount- mount UBIFS volume
ubifsumount- unmount UBIFS volume
usb     - USB sub-system
usbboot - boot from USB device
version - print monitor, compiler and linker version
warmRst - warmRst       - Warn Reset AXP card over PEX.

whoAmI  - - reading CPU ID