Advertisement
Not a member of Pastebin yet?
Sign Up,
it unlocks many cool features!
- mint@mint ~ $ sudo smartctl -a /dev/sda
- smartctl 6.5 2016-01-24 r4214 [x86_64-linux-4.4.0-53-generic] (local build)
- Copyright (C) 2002-16, Bruce Allen, Christian Franke, www.smartmontools.org
- === START OF INFORMATION SECTION ===
- Device Model: TOSHIBA MK5055GSXN
- Serial Number: Z928S0WVS
- LU WWN Device Id: 5 000039 23598071b
- Firmware Version: GC002M
- User Capacity: 500,107,862,016 bytes [500 GB]
- Sector Size: 512 bytes logical/physical
- Device is: Not in smartctl database [for details use: -P showall]
- ATA Version is: ATA8-ACS (minor revision not indicated)
- SATA Version is: SATA 2.6, 3.0 Gb/s
- Local Time is: Sat Feb 25 20:45:09 2017 UTC
- SMART support is: Available - device has SMART capability.
- SMART support is: Enabled
- === START OF READ SMART DATA SECTION ===
- SMART overall-health self-assessment test result: PASSED
- General SMART Values:
- Offline data collection status: (0x00) Offline data collection activity
- was never started.
- Auto Offline Data Collection: Disabled.
- Self-test execution status: ( 0) The previous self-test routine completed
- without error or no self-test has ever
- been run.
- Total time to complete Offline
- data collection: ( 120) seconds.
- Offline data collection
- capabilities: (0x5b) SMART execute Offline immediate.
- Auto Offline data collection on/off support.
- Suspend Offline collection upon new
- command.
- Offline surface scan supported.
- Self-test supported.
- No Conveyance Self-test supported.
- Selective Self-test supported.
- SMART capabilities: (0x0003) Saves SMART data before entering
- power-saving mode.
- Supports SMART auto save timer.
- Error logging capability: (0x01) Error logging supported.
- General Purpose Logging supported.
- Short self-test routine
- recommended polling time: ( 2) minutes.
- Extended self-test routine
- recommended polling time: ( 194) minutes.
- SCT capabilities: (0x0039) SCT Status supported.
- SCT Error Recovery Control supported.
- SCT Feature Control supported.
- SCT Data Table supported.
- SMART Attributes Data Structure revision number: 16
- Vendor Specific SMART Attributes with Thresholds:
- ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
- 1 Raw_Read_Error_Rate 0x000b 100 100 050 Pre-fail Always - 0
- 2 Throughput_Performance 0x0005 100 100 050 Pre-fail Offline - 0
- 3 Spin_Up_Time 0x0027 100 100 001 Pre-fail Always - 1323
- 4 Start_Stop_Count 0x0032 100 100 000 Old_age Always - 7050
- 5 Reallocated_Sector_Ct 0x0033 100 100 050 Pre-fail Always - 1
- 7 Seek_Error_Rate 0x000b 100 100 050 Pre-fail Always - 0
- 8 Seek_Time_Performance 0x0005 100 100 050 Pre-fail Offline - 0
- 9 Power_On_Hours 0x0032 058 058 000 Old_age Always - 17026
- 10 Spin_Retry_Count 0x0033 240 100 030 Pre-fail Always - 0
- 12 Power_Cycle_Count 0x0032 100 100 000 Old_age Always - 6985
- 191 G-Sense_Error_Rate 0x0032 100 100 000 Old_age Always - 1121
- 192 Power-Off_Retract_Count 0x0032 100 100 000 Old_age Always - 285
- 193 Load_Cycle_Count 0x0032 091 091 000 Old_age Always - 96184
- 194 Temperature_Celsius 0x0022 100 100 000 Old_age Always - 36 (Min/Max 4/56)
- 196 Reallocated_Event_Count 0x0032 100 100 000 Old_age Always - 1
- 197 Current_Pending_Sector 0x0032 100 100 000 Old_age Always - 1
- 198 Offline_Uncorrectable 0x0030 100 100 000 Old_age Offline - 0
- 199 UDMA_CRC_Error_Count 0x0032 200 253 000 Old_age Always - 0
- 220 Disk_Shift 0x0002 100 100 000 Old_age Always - 8245
- 222 Loaded_Hours 0x0032 064 064 000 Old_age Always - 14630
- 223 Load_Retry_Count 0x0032 100 100 000 Old_age Always - 0
- 224 Load_Friction 0x0022 100 100 000 Old_age Always - 0
- 226 Load-in_Time 0x0026 100 100 000 Old_age Always - 352
- 240 Head_Flying_Hours 0x0001 100 100 001 Pre-fail Offline - 0
- SMART Error Log Version: 1
- ATA Error Count: 2547 (device log contains only the most recent five errors)
- CR = Command Register [HEX]
- FR = Features Register [HEX]
- SC = Sector Count Register [HEX]
- SN = Sector Number Register [HEX]
- CL = Cylinder Low Register [HEX]
- CH = Cylinder High Register [HEX]
- DH = Device/Head Register [HEX]
- DC = Device Command Register [HEX]
- ER = Error register [HEX]
- ST = Status register [HEX]
- Powered_Up_Time is measured from power on, and printed as
- DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
- SS=sec, and sss=millisec. It "wraps" after 49.710 days.
- Error 2547 occurred at disk power-on lifetime: 16864 hours (702 days + 16 hours)
- When the command that caused the error occurred, the device was active or idle.
- After command completion occurred, registers were:
- ER ST SC SN CL CH DH
- -- -- -- -- -- -- --
- 40 41 a2 68 9a 19 60 Error: UNC at LBA = 0x00199a68 = 1677928
- Commands leading to the command that caused the error were:
- CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
- -- -- -- -- -- -- -- -- ---------------- --------------------
- 60 08 a0 68 9a 19 40 00 00:06:45.618 READ FPDMA QUEUED
- ec 00 00 00 00 00 00 00 00:06:44.932 IDENTIFY DEVICE
- ef 02 00 00 00 00 40 00 00:06:44.823 SET FEATURES [Enable write cache]
- ef 03 45 00 00 00 40 00 00:06:44.716 SET FEATURES [Set transfer mode]
- c6 00 10 00 00 00 40 00 00:06:44.612 SET MULTIPLE MODE
- Error 2546 occurred at disk power-on lifetime: 16864 hours (702 days + 16 hours)
- When the command that caused the error occurred, the device was active or idle.
- After command completion occurred, registers were:
- ER ST SC SN CL CH DH
- -- -- -- -- -- -- --
- 40 41 5a 68 9a 19 60 Error: UNC at LBA = 0x00199a68 = 1677928
- Commands leading to the command that caused the error were:
- CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
- -- -- -- -- -- -- -- -- ---------------- --------------------
- 60 08 58 68 9a 19 40 00 00:04:42.362 READ FPDMA QUEUED
- 2f 00 01 10 00 00 40 00 00:04:42.362 READ LOG EXT
- 60 08 48 68 9a 19 40 00 00:04:38.340 READ FPDMA QUEUED
- 2f 00 01 10 00 00 40 00 00:04:38.339 READ LOG EXT
- 60 08 38 68 9a 19 40 00 00:04:34.318 READ FPDMA QUEUED
- Error 2545 occurred at disk power-on lifetime: 16864 hours (702 days + 16 hours)
- When the command that caused the error occurred, the device was active or idle.
- After command completion occurred, registers were:
- ER ST SC SN CL CH DH
- -- -- -- -- -- -- --
- 40 41 4a 68 9a 19 60 Error: UNC at LBA = 0x00199a68 = 1677928
- Commands leading to the command that caused the error were:
- CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
- -- -- -- -- -- -- -- -- ---------------- --------------------
- 60 08 48 68 9a 19 40 00 00:04:38.340 READ FPDMA QUEUED
- 2f 00 01 10 00 00 40 00 00:04:38.339 READ LOG EXT
- 60 08 38 68 9a 19 40 00 00:04:34.318 READ FPDMA QUEUED
- 2f 00 01 10 00 00 40 00 00:04:34.317 READ LOG EXT
- 60 08 28 68 9a 19 40 00 00:04:30.295 READ FPDMA QUEUED
- Error 2544 occurred at disk power-on lifetime: 16864 hours (702 days + 16 hours)
- When the command that caused the error occurred, the device was active or idle.
- After command completion occurred, registers were:
- ER ST SC SN CL CH DH
- -- -- -- -- -- -- --
- 40 41 3a 68 9a 19 60 Error: UNC at LBA = 0x00199a68 = 1677928
- Commands leading to the command that caused the error were:
- CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
- -- -- -- -- -- -- -- -- ---------------- --------------------
- 60 08 38 68 9a 19 40 00 00:04:34.318 READ FPDMA QUEUED
- 2f 00 01 10 00 00 40 00 00:04:34.317 READ LOG EXT
- 60 08 28 68 9a 19 40 00 00:04:30.295 READ FPDMA QUEUED
- 2f 00 01 10 00 00 40 00 00:04:30.295 READ LOG EXT
- 60 08 18 68 9a 19 40 00 00:04:26.273 READ FPDMA QUEUED
- Error 2543 occurred at disk power-on lifetime: 16864 hours (702 days + 16 hours)
- When the command that caused the error occurred, the device was active or idle.
- After command completion occurred, registers were:
- ER ST SC SN CL CH DH
- -- -- -- -- -- -- --
- 40 41 2a 68 9a 19 60 Error: UNC at LBA = 0x00199a68 = 1677928
- Commands leading to the command that caused the error were:
- CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
- -- -- -- -- -- -- -- -- ---------------- --------------------
- 60 08 28 68 9a 19 40 00 00:04:30.295 READ FPDMA QUEUED
- 2f 00 01 10 00 00 40 00 00:04:30.295 READ LOG EXT
- 60 08 18 68 9a 19 40 00 00:04:26.273 READ FPDMA QUEUED
- 2f 00 01 10 00 00 40 00 00:04:26.273 READ LOG EXT
- 60 08 08 68 9a 19 40 00 00:04:22.251 READ FPDMA QUEUED
- SMART Self-test log structure revision number 1
- No self-tests have been logged. [To run self-tests, use: smartctl -t]
- SMART Selective self-test log data structure revision number 1
- SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
- 1 0 0 Not_testing
- 2 0 0 Not_testing
- 3 0 0 Not_testing
- 4 0 0 Not_testing
- 5 0 0 Not_testing
- Selective self-test flags (0x0):
- After scanning selected spans, do NOT read-scan remainder of disk.
- If Selective self-test is pending on power-up, resume after 0 minute delay.
- mint@mint ~ $
Advertisement
Add Comment
Please, Sign In to add comment
Advertisement