Linux version 2.6.35.3-1129-g691c08a (bulkin@bulkin-desktop) (gcc version 4.5.2 (Sourcery G++ Lite 2011.03-41) ) #485 PREEMPT Thu Oct 25 14:22:54 MSK 2012
CPU: ARMv7 Processor [412fc085] revision 5 (ARMv7), cr=10c53c7f
CPU: VIPT nonaliasing data cache, VIPT nonaliasing instruction cache
Machine: Freescale MX53 LOCO Board
Memory policy: ECC disabled, Data cache writeback
On node 0 totalpages: 57344
free_area_init_node: node 0, pgdat 8051be4c, node_mem_map 80549000
  DMA zone: 192 pages used for memmap
  DMA zone: 0 pages reserved
  DMA zone: 24384 pages, LIFO batch:3
  Normal zone: 256 pages used for memmap
  Normal zone: 32512 pages, LIFO batch:7
Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 56896
Kernel command line: noinitrd console=ttymxc0,115200 video=mxcdi0fb:RGB888,SK-800x480-LVDS video=mxcdi1fb:RGB888,SK-800x480-LVDS di0_primary ldb=di0 root=/dev/nfs nfsroot=192.168.0.2:/home/bulkin/share,nolock,rsize=1024,wsize=1024 ip=192.168.0.136:192.168.0.2:192.168.0.2:255.255.255.0
PID hash table entries: 1024 (order: 0, 4096 bytes)
Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
Memory: 224MB = 224MB total
Memory: 221976k/221976k available, 7400k reserved, 0K highmem
Virtual kernel memory layout:
    vector  : 0xffff0000 - 0xffff1000   (   4 kB)
    fixmap  : 0xfff00000 - 0xfffe0000   ( 896 kB)
    DMA     : 0xf9e00000 - 0xffe00000   (  96 MB)
    vmalloc : 0x8e800000 - 0xf4000000   (1624 MB)
    lowmem  : 0x80000000 - 0x8e000000   ( 224 MB)
    pkmap   : 0x7fe00000 - 0x80000000   (   2 MB)
    modules : 0x7f000000 - 0x7fe00000   (  14 MB)
      .init : 0x80008000 - 0x80029000   ( 132 kB)
      .text : 0x80029000 - 0x804b3000   (4648 kB)
      .data : 0x804d4000 - 0x8051ccc0   ( 292 kB)
SLUB: Genslabs=11, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
Hierarchical RCU implementation.
	RCU-based detection of stalled CPUs is disabled.
	Verbose stalled-CPUs detection is disabled.
NR_IRQS:368
MXC GPIO hardware
MXC IRQ initialized
MXC_Early serial console at MMIO 0x53fbc000 (options '115200')
bootconsole [ttymxc0] enabled
Console: colour dummy device 80x30
Calibrating delay loop... 799.53 BogoMIPS (lpj=3997696)
pid_max: default: 32768 minimum: 301
Mount-cache hash table entries: 512
CPU: Testing write buffer coherency: ok
regulator: core version 0.5
regulator: dummy:
NET: Registered protocol family 16
i.MX IRAM pool: 128 KB@0x8e840000
IRAM READY
CPU is i.MX53 Revision 2.1
Using SDMA I.API
MXC DMA API initialized
IMX usb wakeup probe
the wakeup pdata is 0x804e15a8
IMX usb wakeup probe
the wakeup pdata is 0x804e165c
bio: create slab <bio-0> at 0
SCSI subsystem initialized
libata version 3.00 loaded.
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
IPU DMFC NORMAL mode: 1(0~1), 5B(4,5), 5F(6,7)
Advanced Linux Sound Architecture Driver Version 1.0.23.
Switching to clocksource mxc_timer1
NET: Registered protocol family 2
IP route cache hash table entries: 2048 (order: 1, 8192 bytes)
TCP established hash table entries: 8192 (order: 4, 65536 bytes)
TCP bind hash table entries: 8192 (order: 3, 32768 bytes)
TCP: Hash tables configured (established 8192 bind 8192)
TCP reno registered
UDP hash table entries: 256 (order: 0, 4096 bytes)
UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
NET: Registered protocol family 1
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
RPC: Registered tcp NFSv4.1 backchannel transport module.
LPMode driver module loaded
Static Power Management for Freescale i.MX5
PM driver module loaded
sdram autogating driver module loaded
Bus freq driver module loaded
DI0 is primary
mxc_dvfs_core_probe
regulator: get() with no identifier
mxc_dvfs_core_probe: failed to get gp regulator
DVFS driver module loaded
i.MXC CPU frequency driver
regulator: get() with no identifier
mxc_cpufreq_driver_init: failed to get gp regulator
DVFS PER driver module loaded
msgmni has been set to 433
alg: No test for stdrng (krng)
cryptodev: driver loaded.
io scheduler noop registered
io scheduler deadline registered
io scheduler cfq registered (default)
regulator: get() with no identifier
mxc_ipu mxc_ipu: Channel already disabled 9
mxc_ipu mxc_ipu: Channel already uninitialized 9
Console: switching to colour frame buffer device 100x30
mxc_ipu mxc_ipu: Channel already disabled 7
mxc_ipu mxc_ipu: Channel already uninitialized 7
mxc_ipu mxc_ipu: Channel already disabled 10
mxc_ipu mxc_ipu: Channel already uninitialized 10
Serial: MXC Internal UART driver
mxcintuart.0: ttymxc0 at MMIO 0x53fbc000 (irq = 31) is a Freescale i.MX
console [ttymxc0] enabled, bootconsole disabled
mxcintuart.1: ttymxc1 at MMIO 0x53fc0000 (irq = 32) is a Freescale i.MX
mxcintuart.2: ttymxc2 at MMIO 0x5000c000 (irq = 33) is a Freescale i.MX
mxcintuart.3: ttymxc3 at MMIO 0x53ff0000 (irq = 13) is a Freescale i.MX
mxcintuart.4: ttymxc4 at MMIO 0x63f90000 (irq = 86) is a Freescale i.MX
loop: module loaded
NO SATA device is found, relase resource!
MXC MTD nand Driver 3.0
NAND device: Manufacturer ID: 0xec, Chip ID: 0xda (Samsung NAND 256MiB 3,3V 8-bit)
Bad block table found at page 131008, version 0x01
Bad block table found at page 130944, version 0x01
nand_read_bbt: Bad block at 0x000000040000
nand_read_bbt: Bad block at 0x0000029e0000
nand_read_bbt: Bad block at 0x000002f80000
nand_read_bbt: Bad block at 0x000003b60000
nand_read_bbt: Bad block at 0x0000046e0000
nand_read_bbt: Bad block at 0x0000052a0000
nand_read_bbt: Bad block at 0x000005640000
nand_read_bbt: Bad block at 0x000005d20000
nand_read_bbt: Bad block at 0x0000064e0000
nand_read_bbt: Bad block at 0x000007f00000
nand_read_bbt: Bad block at 0x000008100000
nand_read_bbt: Bad block at 0x000009060000
nand_read_bbt: Bad block at 0x000009b20000
nand_read_bbt: Bad block at 0x00000cb60000
RedBoot partition parsing not available
Creating 2 MTD partitions on "NAND 256MiB 3,3V 8-bit":
0x000000000000-0x000002000000 : "bootloader and kernel"
0x000002000000-0x000010000000 : "nand.rootfs"
vcan: Virtual CAN interface driver
FEC Ethernet Driver
fec_enet_mii_bus: probed
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
fsl-ehci fsl-ehci.0: Freescale On-Chip EHCI Host Controller
fsl-ehci fsl-ehci.0: new USB bus registered, assigned bus number 1
fsl-ehci fsl-ehci.0: irq 18, io base 0x53f80000
fsl-ehci fsl-ehci.0: USB 2.0 started, EHCI 1.00
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 1 port detected
fsl-ehci fsl-ehci.1: Freescale On-Chip EHCI Host Controller
fsl-ehci fsl-ehci.1: new USB bus registered, assigned bus number 2
fsl-ehci fsl-ehci.1: irq 14, io base 0x53f80200
fsl-ehci fsl-ehci.1: USB 2.0 started, EHCI 1.00
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 1 port detected
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
mice: PS/2 mouse device common for all mice
spi0.0 supply vcc not found, using dummy regulator
ads7846 spi0.0: touchscreen, irq 137
input: ADS7843 Touchscreen as /devices/platform/spi_gpio.0/spi0.0/input/input0
spi1.0 supply vcc not found, using dummy regulator
ads7846 spi1.0: touchscreen, irq 131
input: ADS7843 Touchscreen as /devices/platform/spi_gpio.1/spi1.0/input/input1
rtc-ds1307 1-0068: SET TIME!
rtc-ds1307 1-0068: SET TIME!
rtc-ds1307 1-0068: SET TIME!
rtc-ds1307 1-0068: SET TIME!
rtc-ds1307 1-0068: SET TIME!
usb 2-1: new high speed USB device using fsl-ehci and address 2
rtc-ds1307 1-0068: SET TIME!
rtc-ds1307: probe of 1-0068 failed with error -5
mxc_rtc mxc_rtc.0: rtc core: registered mxc_rtc as rtc0
i2c /dev entries driver
Linux video capture interface: v2.00
1-003c supply DA9052_LDO9 not found, using dummy regulator
1-003c supply DA9052_LDO7 not found, using dummy regulator
mxc_v4l2_output mxc_v4l2_output.0: Registered device video1
uvcvideo: Found UVC 1.00 device <unnamed> (046d:0817)
input: UVC Camera (046d:0817) as /devices/platform/fsl-ehci.1/usb2/2-1/2-1:1.0/input/input2
usbcore: registered new interface driver uvcvideo
USB Video Class driver (v0.1.0)
MXC WatchDog Driver 2.0
MXC Watchdog # 0 Timer: initial timeout 60 sec
VPU initialized
mxc_asrc registered
gpu mmu enabled
mxsdhci: MXC Secure Digital Host Controller Interface driver
mxsdhci: MXC SDHCI Controller Driver.
mmc0: SDHCI detect irq 135 irq 1 INTERNAL DMA
mxsdhci: MXC SDHCI Controller Driver.
mmc1: SDHCI detect irq 129 irq 2 INTERNAL DMA
usbcore: registered new interface driver usbhid
usbhid: USB HID core driver
No device for DAI tlv320aic23
No device for DAI imx-ssi-1-0
No device for DAI imx-ssi-1-1
No device for DAI imx-ssi-2-0
No device for DAI imx-ssi-2-1
AIC23 Audio Codec 0.1
DMA Sound Buffer Allocated: Playback UseIram=1 ext_ram=0 buf->addr=f8016000 buf->area=8e856000 size=24576
DMA Sound Buffer Allocated: Capture  UseIram=1 ext_ram=1 buf->addr=7d200000 buf->area=fa8ac000 size=24576
asoc: tlv320aic23 <-> imx-ssi-2-0 mapping ok
tlv320aic23_write cannot write 117 to register R0
tlv320aic23_write cannot write 117 to register R1
ALSA device list:
  #0: imx-3stack (tlv320aic23)
TCP cubic registered
NET: Registered protocol family 17
can: controller area network core (rev 20090105 abi 8)
NET: Registered protocol family 29
can: raw protocol (rev 20090105)
can: broadcast manager protocol (rev 20090105 t)
VFP support v0.3: implementor 41 architecture 3 part 30 variant c rev 2
mxc_rtc mxc_rtc.0: setting system clock to 1970-01-01 03:44:40 UTC (13480)
eth0: Freescale FEC PHY driver [Generic PHY] (mii_bus:phy_addr=0:00, irq=-1)
IP-Config: Complete:
     device=eth0, addr=192.168.0.136, mask=255.255.255.0, gw=192.168.0.2,
     host=192.168.0.136, domain=, nis-domain=(none),
     bootserver=192.168.0.2, rootserver=192.168.0.2, rootpath=
Looking up port of RPC 100003/2 on 192.168.0.2
PHY: 0:00 - Link is Up - 100/Full
Looking up port of RPC 100005/1 on 192.168.0.2
VFS: Mounted root (nfs filesystem) on device 0:11.
Freeing init memory: 132K