Advertisement
Not a member of Pastebin yet?
Sign Up,
it unlocks many cool features!
- iw phy
- Wiphy phy0
- max # scan SSIDs: 4
- max scan IEs length: 2257 bytes
- Retry short limit: 7
- Retry long limit: 4
- Coverage class: 0 (up to 0m)
- Device supports RSN-IBSS.
- Device supports AP-side u-APSD.
- Device supports T-DLS.
- Supported Ciphers:
- * WEP40 (00-0f-ac:1)
- * WEP104 (00-0f-ac:5)
- * TKIP (00-0f-ac:2)
- * CCMP (00-0f-ac:4)
- * 00-0f-ac:10
- * GCMP (00-0f-ac:8)
- * 00-0f-ac:9
- * CMAC (00-0f-ac:6)
- * 00-0f-ac:13
- * 00-0f-ac:11
- * 00-0f-ac:12
- Available Antennas: TX 0x1 RX 0x3
- Configured Antennas: TX 0x1 RX 0x3
- Supported interface modes:
- * IBSS
- * managed
- * AP
- * AP/VLAN
- * WDS
- * monitor
- * mesh point
- * P2P-client
- * P2P-GO
- * Unknown mode (11)
- Band 1:
- Capabilities: 0x11ce
- HT20/HT40
- SM Power Save disabled
- RX HT40 SGI
- TX STBC
- RX STBC 1-stream
- Max AMSDU length: 3839 bytes
- DSSS/CCK HT40
- Maximum RX AMPDU length 65535 bytes (exponent: 0x003)
- Minimum RX AMPDU time spacing: 8 usec (0x06)
- HT RX MCS rate indexes supported: 0-15
- TX unequal modulation not supported
- HT TX Max spatial streams: 1
- HT TX MCS rate indexes supported may differ
- Bitrates (non-HT):
- * 1.0 Mbps
- * 2.0 Mbps (short preamble supported)
- * 5.5 Mbps (short preamble supported)
- * 11.0 Mbps (short preamble supported)
- * 6.0 Mbps
- * 9.0 Mbps
- * 12.0 Mbps
- * 18.0 Mbps
- * 24.0 Mbps
- * 36.0 Mbps
- * 48.0 Mbps
- * 54.0 Mbps
- Frequencies:
- * 2412 MHz [1] (16.0 dBm)
- * 2417 MHz [2] (16.0 dBm)
- * 2422 MHz [3] (16.0 dBm)
- * 2427 MHz [4] (16.0 dBm)
- * 2432 MHz [5] (16.0 dBm)
- * 2437 MHz [6] (16.0 dBm)
- * 2442 MHz [7] (16.0 dBm)
- * 2447 MHz [8] (16.0 dBm)
- * 2452 MHz [9] (16.0 dBm)
- * 2457 MHz [10] (16.0 dBm)
- * 2462 MHz [11] (15.0 dBm)
- * 2467 MHz [12] (16.0 dBm)
- * 2472 MHz [13] (16.0 dBm)
- * 2484 MHz [14] (17.0 dBm) (no IR)
- Supported commands:
- * new_interface
- * set_interface
- * new_key
- * start_ap
- * new_station
- * new_mpath
- * set_mesh_config
- * set_bss
- * authenticate
- * associate
- * deauthenticate
- * disassociate
- * join_ibss
- * join_mesh
- * remain_on_channel
- * set_tx_bitrate_mask
- * frame
- * frame_wait_cancel
- * set_wiphy_netns
- * set_channel
- * set_wds_peer
- * tdls_mgmt
- * tdls_oper
- * probe_client
- * set_noack_map
- * register_beacons
- * start_p2p_device
- * set_mcast_rate
- * channel_switch
- * Unknown command (104)
- * connect
- * disconnect
- Supported TX frame types:
- * IBSS: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
- * managed: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
- * AP: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
- * AP/VLAN: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
- * mesh point: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
- * P2P-client: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
- * P2P-GO: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
- * P2P-device: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
- Supported RX frame types:
- * IBSS: 0x40 0xb0 0xc0 0xd0
- * managed: 0x40 0xd0
- * AP: 0x00 0x20 0x40 0xa0 0xb0 0xc0 0xd0
- * AP/VLAN: 0x00 0x20 0x40 0xa0 0xb0 0xc0 0xd0
- * mesh point: 0xb0 0xc0 0xd0
- * P2P-client: 0x40 0xd0
- * P2P-GO: 0x00 0x20 0x40 0xa0 0xb0 0xc0 0xd0
- * P2P-device: 0x40 0xd0
- software interface modes (can always be added):
- * AP/VLAN
- * monitor
- valid interface combinations:
- * #{ managed } <= 2048, #{ AP, mesh point } <= 8, #{ P2P-client, P2P-GO } <= 1,
- total <= 2048, #channels <= 1, STA/AP BI must match
- * #{ WDS } <= 2048,
- total <= 2048, #channels <= 1, STA/AP BI must match
- HT Capability overrides:
- * MCS: ff ff ff ff ff ff ff ff ff ff
- * maximum A-MSDU length
- * supported channel width
- * short GI for 40 MHz
- * max A-MPDU length exponent
- * min MPDU start spacing
- Device supports TX status socket option.
- Device supports HT-IBSS.
- Device supports SAE with AUTHENTICATE command
- Device supports low priority scan.
- Device supports scan flush.
- Device supports AP scan.
- Device supports per-vif TX power setting
- P2P GO supports CT window setting
- Driver supports a userspace MPM
- Device supports active monitor (which will ACK incoming frames)
- Driver/device bandwidth changes during BSS lifetime (AP/GO mode)
Advertisement
Add Comment
Please, Sign In to add comment
Advertisement