<6>[    0.000000] Booting Linux on physical CPU 0
<6>[    0.000000] Initializing cgroup subsys cpu
<4>[    0.000000] CPU: ARMv6-compatible processor [410fb767] revision 7 (ARMv7), cr=00c5387d
<4>[    0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT nonaliasing instruction cache
<4>[    0.000000] Machine: BCM2708
<6>[    0.000000] cma: CMA: reserved 16 MiB at 0f000000
<4>[    0.000000] Memory policy: ECC disabled, Data cache writeback
<7>[    0.000000] On node 0 totalpages: 65536
<7>[    0.000000] free_area_init_node: node 0, pgdat c053d894, node_mem_map c05e7000
<7>[    0.000000]   Normal zone: 512 pages used for memmap
<7>[    0.000000]   Normal zone: 0 pages reserved
<7>[    0.000000]   Normal zone: 65024 pages, LIFO batch:15
<7>[    0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
<7>[    0.000000] pcpu-alloc: [0] 0
<4>[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 65024

<6>[    0.000000] PID hash table entries: 1024 (order: 0, 4096 bytes)
<6>[    0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
<6>[    0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
<6>[    0.000000] Memory: 256MB = 256MB total
<5>[    0.000000] Memory: 237384k/237384k available, 24760k reserved, 0K highmem
<5>[    0.000000] Virtual kernel memory layout:
<5>[    0.000000]     vector  : 0xffff0000 - 0xffff1000   (   4 kB)
<5>[    0.000000]     fixmap  : 0xfff00000 - 0xfffe0000   ( 896 kB)
<6>[    0.000000] NR_IRQS:330
<6>[    0.000000] sched_clock: 32 bits at 1000kHz, resolution 1000ns, wraps every 4294967ms
<6>[    0.000000] Console: colour dummy device 80x30
<6>[    0.000000] console [tty1] enabled
<6>[    0.000728] Calibrating delay loop... 996.14 BogoMIPS (lpj=4980736)
<6>[    0.040093] pid_max: default: 32768 minimum: 301
<6>[    0.040317] Mount-cache hash table entries: 512
<6>[    0.040864] Initializing cgroup subsys cpuacct
<6>[    0.040902] Initializing cgroup subsys devices
<6>[    0.040923] Initializing cgroup subsys freezer
<6>[    0.040943] Initializing cgroup subsys blkio
<6>[    0.041005] CPU: Testing write buffer coherency: ok
<6>[    0.041237] hw perfevents: enabled with v6 PMU driver, 3 counters available
<6>[    0.041338] Setting up static identity map for 0x39e698 - 0x39e6f4
<6>[    0.042327] devtmpfs: initialized
<6>[    0.049228] NET: Registered protocol family 16
<6>[    0.054526] DMA: preallocated 4096 KiB pool for atomic coherent allocations
<4>[    0.055267] bcm2708.uart_clock = 0
<6>[    0.056204] hw-breakpoint: found 6 breakpoint and 1 watchpoint registers.
<6>[    0.056247] hw-breakpoint: maximum watchpoint size is 4 bytes.
<6>[    0.056272] mailbox: Broadcom VideoCore Mailbox driver
<6>[    0.056340] bcm2708_vcio: mailbox at f200b880
<6>[    0.056410] bcm_power: Broadcom power driver
<4>[    0.056436] bcm_power_open() -> 0
<4>[    0.056452] bcm_power_request(0, 8)
<4>[    0.557028] bcm_mailbox_read -> 00000080, 0
<4>[    0.557061] bcm_power_request -> 0
<6>[    0.557079] Serial: AMBA PL011 UART driver
<6>[    0.557184] dev:f1: ttyAMA0 at MMIO 0x20201000 (irq = 83) is a PL011 rev3
<6>[    0.881346] console [ttyAMA0] enabled
<6>[    0.898877] bio: create slab <bio-0> at 0
<5>[    0.903546] SCSI subsystem initialized
<6>[    0.907449] usbcore: registered new interface driver usbfs
<6>[    0.913057] usbcore: registered new interface driver hub
<6>[    0.918534] usbcore: registered new device driver usb
<6>[    0.924503] Switching to clocksource stc
<5>[    0.928578] FS-Cache: Loaded
<6>[    0.931631] CacheFiles: Loaded
<6>[    0.942151] NET: Registered protocol family 2
<6>[    0.947101] TCP established hash table entries: 8192 (order: 4, 65536 bytes)
<6>[    0.954391] TCP bind hash table entries: 8192 (order: 3, 32768 bytes)
<6>[    0.960943] TCP: Hash tables configured (established 8192 bind 8192)
<6>[    0.967329] TCP: reno registered
<6>[    0.970584] UDP hash table entries: 256 (order: 0, 4096 bytes)
<6>[    0.976434] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
<6>[    0.982909] NET: Registered protocol family 1
<6>[    0.987619] RPC: Registered named UNIX socket transport module.
<6>[    0.993616] RPC: Registered udp transport module.
<6>[    0.998324] RPC: Registered tcp transport module.
<6>[    1.003045] RPC: Registered tcp NFSv4.1 backchannel transport module.
<6>[    1.009942] bcm2708_dma: DMA manager at f2007000
<6>[    1.014629] bcm2708_gpio: bcm2708_gpio_probe c0517d98
<4>[    1.020009] vc-mem: phys_addr:0x00000000 mem_base=0x1ec00000 mem_size:0x20000000(512 MiB)
<6>[    1.028904] audit: initializing netlink socket (disabled)
<5>[    1.034356] type=2000 audit(0.880:1): initialized
<5>[    1.121410] VFS: Disk quotas dquot_6.5.2
<4>[    1.125409] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
<5>[    1.132297] FS-Cache: Netfs 'nfs' registered for caching
<5>[    1.137870] NFS: Registering the id_resolver key type
<5>[    1.143067] Key type id_resolver registered
<5>[    1.147260] Key type id_legacy registered
<6>[    1.151528] msgmni has been set to 495
<6>[    1.156399] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 252)
<6>[    1.164076] io scheduler noop registered
<6>[    1.168015] io scheduler deadline registered
<6>[    1.172371] io scheduler cfq registered (default)
<6>[    1.198709] Console: switching to colour frame buffer device 234x66
<6>[    1.218027] kgdb: Registered I/O driver kgdboc.
<6>[    1.223127] vc-cma: Videocore CMA driver
<6>[    1.227114] vc-cma: vc_cma_base      = 0x00000000
<6>[    1.231909] vc-cma: vc_cma_size      = 0x00000000 (0 MiB)
<6>[    1.237370] vc-cma: vc_cma_initial   = 0x00000000 (0 MiB)
<6>[    1.249096] brd: module loaded
<6>[    1.255629] loop: module loaded
<6>[    1.259162] vchiq: vchiq_init_state: slot_zero = 0xcf000000, is_master = 0
<6>[    1.266746] Loading iSCSI transport class v2.0-870.
<6>[    1.272454] usbcore: registered new interface driver smsc95xx
<6>[    1.278334] dwc_otg: version 3.00a 10-AUG-2012 (platform bus)
<4>[    1.489238] Core Release: 2.80a
<4>[    1.492435] Setting default values for core params
<4>[    1.497294] Finished setting default values for core params
<4>[    1.707963] Using Buffer DMA mode
<4>[    1.711355] Periodic Transfer Interrupt Enhancement - disabled
<4>[    1.717249] Multiprocessor Interrupt Enhancement - disabled
<4>[    1.722896] OTG VER PARAM: 0, OTG VER FLAG: 0
<4>[    1.727303] Dedicated Tx FIFOs mode
<7>[    1.731430] dwc_otg: Microframe scheduler enabled
<6>[    1.731675] dwc_otg bcm2708_usb: DWC OTG Controller
<6>[    1.736657] dwc_otg bcm2708_usb: new USB bus registered, assigned bus number 1
<6>[    1.744047] dwc_otg bcm2708_usb: irq 32, io mem 0x00000000
<4>[    1.749666] Init: Port Power? op_state=1
<4>[    1.753632] Init: Power Port (0)
<6>[    1.756956] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
<6>[    1.763845] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
<6>[    1.771163] usb usb1: Product: DWC OTG Controller
<6>[    1.775918] usb usb1: Manufacturer: Linux 3.6.11+ dwc_otg_hcd
<6>[    1.781788] usb usb1: SerialNumber: bcm2708_usb
<6>[    1.786888] hub 1-0:1.0: USB hub found
<6>[    1.790746] hub 1-0:1.0: 1 port detected
<7>[    1.798055] dwc_otg: FIQ enabled
<7>[    1.798067] dwc_otg: NAK holdoff enabled
<7>[    1.798073] dwc_otg: FIQ split fix enabled
<7>[    1.798085] Module dwc_common_port init
<6>[    1.798240] Initializing USB Mass Storage driver...
<6>[    1.806418] usbcore: registered new interface driver usb-storage
<6>[    1.815541] USB Mass Storage support registered.
<6>[    1.823319] usbcore: registered new interface driver libusual
<6>[    1.832367] mousedev: PS/2 mouse device common for all mice
<6>[    1.841468] bcm2835-cpufreq: min=1000000 max=1000000 cur=1000000
<6>[    1.850688] bcm2835-cpufreq: switching to governor powersave
<6>[    1.859421] bcm2835-cpufreq: switching to governor powersave
<6>[    1.868128] cpuidle: using governor ladder
<6>[    1.875266] cpuidle: using governor menu
<6>[    1.882282] sdhci: Secure Digital Host Controller Interface driver
<6>[    1.891570] sdhci: Copyright(c) Pierre Ossman
<4>[    1.899066] sdhci: Enable low-latency mode
<6>[    1.948615] mmc0: SDHCI controller on BCM2708_Arasan [platform] using platform's DMA
<6>[    1.959631] mmc0: BCM2708 SDHC host at 0x20300000 DMA 2 IRQ 77
<6>[    1.970718] sdhci-pltfm: SDHCI platform and OF driver helper
<6>[    1.985023] usbcore: registered new interface driver usbhid
<4>[    1.993863] Indeed it is in host mode hprt0 = 00021501
<6>[    2.004186] usbhid: USB HID core driver
<6>[    2.028579] TCP: cubic registered
<6>[    2.038483] Initializing XFRM netlink socket
<6>[    2.045774] NET: Registered protocol family 17
<5>[    2.078619] Key type dns_resolver registered
<6>[    2.108715] VFP support v0.3: implementor 41 architecture 1 part 20 variant b rev 5
<6>[    2.128997] registered taskstats version 1
<6>[    2.150483] mmc0: read SD Status register (SSR) after 4 attempts
<4>[    2.164760] mmc0: SD Status: Invalid Allocation Unit size.
<6>[    2.175140] mmc0: new SD card at address e624
<6>[    2.183113] mmcblk0: mmc0:e624 SD256 241 MiB
<6>[    2.192198]  mmcblk0: p1 p2
<6>[    2.278510] usb 1-1: new high-speed USB device number 2 using dwc_otg
<4>[    2.288217] Indeed it is in host mode hprt0 = 00001101
<6>[    2.488950] usb 1-1: New USB device found, idVendor=0424, idProduct=9512
<6>[    2.498920] usb 1-1: New USB device strings: Mfr=0, Product=0, SerialNumber=0
<6>[    2.509858] hub 1-1:1.0: USB hub found
<6>[    2.516949] hub 1-1:1.0: 3 ports detected
<6>[    2.798601] usb 1-1.1: new high-speed USB device number 3 using dwc_otg
<6>[    2.908880] usb 1-1.1: New USB device found, idVendor=0424, idProduct=ec00
<6>[    2.919019] usb 1-1.1: New USB device strings: Mfr=0, Product=0, SerialNumber=0
<6>[    2.932177] smsc95xx v1.0.4
<6>[    3.002791] smsc95xx 1-1.1:1.0: eth0: register 'smsc95xx' at usb-bcm2708_usb-1.1, smsc95xx Uc
<6>[    3.108635] usb 1-1.2: new high-speed USB device number 4 using dwc_otg
<6>[    3.218956] usb 1-1.2: New USB device found, idVendor=0424, idProduct=2514
<6>[    3.229331] usb 1-1.2: New USB device strings: Mfr=0, Product=0, SerialNumber=0
<6>[    3.241327] hub 1-1.2:1.0: USB hub found
<6>[    3.249032] hub 1-1.2:1.0: 4 ports detected
<6>[    3.528588] usb 1-1.2.2: new low-speed USB device number 5 using dwc_otg
<6>[    3.693702] usb 1-1.2.2: New USB device found, idVendor=413c, idProduct=2107
<6>[    3.704126] usb 1-1.2.2: New USB device strings: Mfr=1, Product=2, SerialNumber=0
<6>[    3.714960] usb 1-1.2.2: Product: Dell USB Entry Keyboard
<6>[    3.723656] usb 1-1.2.2: Manufacturer: Dell
<6>[    3.751277] input: Dell Dell USB Entry Keyboard as /devices/platform/bcm2708_usb/usb1/1-1/1-0
<6>[    3.766657] hid-generic 0003:413C:2107.0001: input,hidraw0: USB HID v1.10 Keyboard [Dell Del0
<6>[    4.714382] smsc95xx 1-1.1:1.0: eth0: link up, 100Mbps, full-duplex, lpa 0xCDE1
<5>[    4.738484] Sending DHCP requests ., OK
<4>[    4.792426] IP-Config: Got DHCP answer from 0.0.0.0, my address is 10.177.70.88
<6>[    4.803705] IP-Config: Complete:
<6>[    4.810534]      device=eth0, addr=10.177.70.88, mask=255.255.254.0, gw=10.177.70.1
<6>[    4.821771]      host=10.177.70.88, domain=cam.broadcom.com, nis-domain=(none)
<6>[    4.832575]      bootserver=0.0.0.0, rootserver=10.177.71.57, rootpath=
<6>[    4.858743] VFS: Mounted root (nfs filesystem) on device 0:12.
<6>[    4.869352] devtmpfs: mounted
<6>[    4.876342] Freeing init memory: 128K
<30>[    7.505408] udevd[154]: starting version 175
<7>[    9.055368] Registered led device: led0
<6>[   30.364719] bcm2835-cpufreq: switching to governor ondemand
<6>[   30.364739] bcm2835-cpufreq: switching to governor ondemand
<6>[ 1844.896807] Bluetooth: Core ver 2.16
<6>[ 1844.898897] NET: Registered protocol family 31
<6>[ 1844.898941] Bluetooth: HCI device and connection manager initialized
<6>[ 1844.898952] Bluetooth: HCI socket layer initialized
<6>[ 1844.898958] Bluetooth: L2CAP socket layer initialized
<6>[ 1844.898999] Bluetooth: SCO socket layer initialized
<6>[ 1845.017325] Bluetooth: RFCOMM TTY layer initialized
<6>[ 1845.017357] Bluetooth: RFCOMM socket layer initialized
<6>[ 1845.017366] Bluetooth: RFCOMM ver 1.11
<4>[17013.296896] ERROR::handle_hc_chhltd_intr_dma:2574: handle_hc_chhltd_intr_dma: Channel 6, DMA1
<5>[17024.229527] nfs: server 10.177.71.57 not responding, still trying
<5>[17059.541002] nfs: server 10.177.71.57 not responding, still trying
<6>[17085.850079] SysRq : DEBUG