Texas Instruments X-Loader 1.4.4ss (Apr 13 2010 - 22:36:28)
Beagle Rev C1/C2/C3
Reading boot sector
Loading u-boot.bin from mmc


U-Boot 2010.03 (Jun 06 2010 - 10:00:15)

OMAP3530-GP ES3.1, CPU-OPP2, L3-165MHz, Max clock-600Mhz
OMAP3 Beagle board + LPDDR/NAND
I2C:   ready
DRAM:  256 MB
NAND:  256 MiB
In:    serial
Out:   serial
Err:   serial

Probing for expansion boards, if none are connected you'll see a harmless I2C error.

timed out in wait_for_pin: I2C_STAT=0
I2C read: I/O error
Unrecognized expansion board: 0
Beagle Rev C1/C2/C3
Die ID #32e6002400000000040365f80d017022
Hit any key to stop autoboot:  0
mmc1 is available
The user button is currently pressed.
reading user.scr

** Unable to read "user.scr" from mmc 1:1 **
reading uImage

3194800 bytes read
reading ramdisk.gz

** Unable to read "ramdisk.gz" from mmc 1:1 **
Booting from mmc ...
## Booting kernel from Legacy Image at 80200000 ...
   Image Name:   Angstrom/2.6.32/beagleboard
   Image Type:   ARM Linux Kernel Image (uncompressed)
   Data Size:    3194736 Bytes =  3 MB
   Load Address: 80008000
   Entry Point:  80008000
   Verifying Checksum ... OK
   Loading Kernel Image ... OK
OK

Starting kernel ...

Uncompressing Linux.........................................................................................
............................................................................................................
............ done, booting the kernel.
[    0.000000] Linux version 2.6.32 (koen@dominion) (gcc version 4.3.3 (GCC) ) #1 PREEMPT Mon May 3 22:40:09
 CEST 2010
[    0.000000] CPU: ARMv7 Processor [411fc083] revision 3 (ARMv7), cr=10c53c7f
[    0.000000] CPU: VIPT nonaliasing data cache, VIPT nonaliasing instruction cache
[    0.000000] Machine: OMAP3 Beagle Board
[    0.000000] Memory policy: ECC disabled, Data cache writeback
[    0.000000] OMAP3430/3530 ES3.1 (l2cache iva sgx neon isp )
[    0.000000] SRAM: Mapped pa 0x40200000 to va 0xfe400000 size: 0x100000
[    0.000000] Reserving 12582912 bytes SDRAM for VRAM
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 65024
[    0.000000] Kernel command line: console=ttyS2,115200n8 mpurate=600 buddy=unknown vram=12M omapfb.mode=dv
i:640x480MR-16@60 omapdss.def_disp=dvi root=/dev/mmcblk0p2 rw rootfstype=ext3 rootwait
[    0.000000] Beagle expansionboard: unknown
[    0.000000] PID hash table entries: 1024 (order: 0, 4096 bytes)
[    0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
[    0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
[    0.000000] Memory: 128MB 128MB = 256MB total
[    0.000000] Memory: 240384KB available (5892K code, 676K data, 208K init, 0K highmem)
[    0.000000] Hierarchical RCU implementation.
[    0.000000] NR_IRQS:402
[    0.000000] Clocking rate (Crystal/Core/MPU): 26.0/332/500 MHz
[    0.000000] Reprogramming SDRC clock to 332000000 Hz
[    0.000000] GPMC revision 5.0
[    0.000000] IRQ: Found an INTC at 0xfa200000 (revision 4.0) with 96 interrupts
[    0.000000] Total of 96 interrupts on 1 active controller
[    0.000000] OMAP GPIO hardware version 2.5
[    0.000000] OMAP clockevent source: GPTIMER12 at 32768 Hz
[    0.000000] Console: colour dummy device 80x30
[    0.000000] Calibrating delay loop... 475.76 BogoMIPS (lpj=1855488)
[    0.000000] Mount-cache hash table entries: 512
[    0.000000] CPU: Testing write buffer coherency: ok
[    0.000000] tmpfs: No value for mount option 'mode'
[    0.000000] devtmpfs: initialized
[    0.000000] regulator: core version 0.5
[    0.000000] NET: Registered protocol family 16
[    0.000000] Found NAND on CS0
[    0.000000] Registering NAND on CS0
[    0.000000] Unable to get DVI reset GPIO
[    0.000000] Target VDD1 OPP = 5, VDD2 OPP = 2
[    0.000000] omap3evmdc: Driver registration complete
[   13.604980] OMAP DMA hardware revision 4.0
[   13.614013] bio: create slab <bio-0> at 0
[   13.615600] SCSI subsystem initialized
[   13.617401] usbcore: registered new interface driver usbfs
[   13.617584] usbcore: registered new interface driver hub
[   13.617797] usbcore: registered new device driver usb
[   13.618255] i2c_omap i2c_omap.1: bus 1 rev3.12 at 2600 kHz
[   13.621490] twl4030: PIH (irq 7) chaining IRQs 368..375
[   13.621520] twl4030: power (irq 373) chaining IRQs 376..383
[   13.621887] twl4030: gpio (irq 368) chaining IRQs 384..401
[   13.623596] regulator: VUSB1V5: 1500 mV normal standby
[   13.623901] regulator: VUSB1V8: 1800 mV normal standby
[   13.624206] regulator: VUSB3V1: 3100 mV normal standby
[   13.628417] twl4030_usb twl4030_usb: Initialized TWL4030 USB module
[   13.628967] regulator: VMMC1: 1850 <--> 3150 mV normal standby
[   13.629302] regulator: VDAC: 1800 mV normal standby
[   13.629638] regulator: VPLL2: 1800 mV normal standby
[   13.629943] regulator: VSIM: 1800 <--> 3000 mV normal standby
[   13.641296] i2c_omap i2c_omap.2: bus 2 rev3.12 at 400 kHz
[   13.656158] i2c_omap i2c_omap.3: bus 3 rev3.12 at 100 kHz
[   13.657714] Switching to clocksource 32k_counter
[   13.670227] musb_hdrc: version 6.0, musb-dma, otg (peripheral+host), debug=0
[   13.670562] musb_hdrc: USB OTG mode controller at fa0ab000 using DMA, IRQ 92
[   13.670593] musb_hdrc musb_hdrc: MUSB HDRC host driver
[   13.670745] musb_hdrc musb_hdrc: new USB bus registered, assigned bus number 1
[   13.670928] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[   13.670928] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[   13.670959] usb usb1: Product: MUSB HDRC host driver
[   13.670989] usb usb1: Manufacturer: Linux 2.6.32 musb-hcd
[   13.670989] usb usb1: SerialNumber: musb_hdrc
[   13.671752] hub 1-0:1.0: USB hub found
[   13.671813] hub 1-0:1.0: 1 port detected
[   13.673217] NET: Registered protocol family 2
[   13.673583] IP route cache hash table entries: 2048 (order: 1, 8192 bytes)
[   13.674255] TCP established hash table entries: 8192 (order: 4, 65536 bytes)
[   13.674499] TCP bind hash table entries: 8192 (order: 3, 32768 bytes)
[   13.674652] TCP: Hash tables configured (established 8192 bind 8192)
[   13.674682] TCP reno registered
[   13.674682] UDP hash table entries: 256 (order: 0, 4096 bytes)
[   13.674713] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[   13.675018] NET: Registered protocol family 1
[   13.675567] RPC: Registered udp transport module.
[   13.675598] RPC: Registered tcp transport module.
[   13.675598] RPC: Registered tcp NFSv4.1 backchannel transport module.
[   13.676788] omap-iommu omap-iommu.0: isp registered
[   13.676940] OMAP35x  Linux PSP version 03.00.00.05 (OMAP3EVM)
[   13.678924] VFS: Disk quotas dquot_6.5.2
[   13.679077] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[   13.680419] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[   13.681579] JFFS2 version 2.2. (NAND) (SUMMARY)  �© 2001-2006 Red Hat, Inc.
[   13.682617] msgmni has been set to 470
[   13.687957] alg: No test for stdrng (krng)
[   13.688323] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 254)
[   13.688354] io scheduler noop registered
[   13.688354] io scheduler deadline registered
[   13.688568] io scheduler cfq registered (default)
[   13.751770] OMAP DSS rev 2.0
[   13.751831] OMAP DISPC rev 3.0
[   13.751922] OMAP VENC rev 2
[   13.752227] OMAP DSI rev 1.0
[   14.092834] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
[   14.113464] serial8250.0: ttyS0 at MMIO 0x4806a000 (irq = 72) is a ST16654
[   14.133117] serial8250.1: ttyS1 at MMIO 0x4806c000 (irq = 73) is a ST16654
[   14.152770] serial8250.2: ttyS2 at MMIO 0x49020000 (irq = 74) is a ST16654
[   14.703552] console [ttyS2] enabled
[   14.716003] brd: module loaded
[   14.723541] loop: module loaded
[   14.728088] omap2-nand driver initializing
[   14.732574] NAND device: Manufacturer ID: 0x2c, Chip ID: 0xba (Micron NAND 256MiB 1,8V 16-bit)
[   14.741821] cmdlinepart partition parsing not available
[   14.747131] Creating 5 MTD partitions on "omap2-nand":
[   14.752349] 0x000000000000-0x000000080000 : "X-Loader"
[   14.758972] 0x000000080000-0x000000260000 : "U-Boot"
[   14.765686] 0x000000260000-0x000000280000 : "U-Boot Env"
[   14.772033] 0x000000280000-0x000000680000 : "Kernel"
[   14.779571] 0x000000680000-0x000010000000 : "File System"
[   14.887329] usbcore: registered new interface driver catc
[   14.892822] catc: v2.8:CATC EL1210A NetMate USB Ethernet driver
[   14.898895] usbcore: registered new interface driver kaweth
[   14.904541] pegasus: v0.6.14 (2006/09/27), Pegasus/Pegasus II USB Ethernet driver
[   14.912200] usbcore: registered new interface driver pegasus
[   14.917938] rtl8150: v0.6.2 (2004/08/27):rtl8150 based usb-ethernet driver
[   14.924987] usbcore: registered new interface driver rtl8150
[   14.930816] usbcore: registered new interface driver asix
[   14.936401] usbcore: registered new interface driver cdc_ether
[   14.942413] usbcore: registered new interface driver cdc_eem
[   14.948242] usbcore: registered new interface driver dm9601
[   14.953979] usbcore: registered new interface driver smsc95xx
[   14.959899] usbcore: registered new interface driver gl620a
[   14.965667] usbcore: registered new interface driver net1080
[   14.971496] usbcore: registered new interface driver plusb
[   14.977111] usbcore: registered new interface driver rndis_host
[   14.983215] usbcore: registered new interface driver cdc_subset
[   14.989318] usbcore: registered new interface driver zaurus
[   14.995086] usbcore: registered new interface driver MOSCHIP usb-ethernet driver
[   15.003387] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[   15.010345] ehci-omap ehci-omap.0: OMAP-EHCI Host Controller
[   15.016418] ehci-omap ehci-omap.0: new USB bus registered, assigned bus number 2
[   15.024108] ehci-omap ehci-omap.0: irq 77, io mem 0x48064800
[   15.040679] ehci-omap ehci-omap.0: USB 2.0 started, EHCI 1.00
[   15.046600] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002
[   15.053497] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[   15.060791] usb usb2: Product: OMAP-EHCI Host Controller
[   15.066162] usb usb2: Manufacturer: Linux 2.6.32 ehci_hcd
[   15.071624] usb usb2: SerialNumber: ehci-omap.0
[   15.077056] hub 2-0:1.0: USB hub found
[   15.080902] hub 2-0:1.0: 3 ports detected
[   15.111145] Initializing USB Mass Storage driver...
[   15.116241] usbcore: registered new interface driver usb-storage
[   15.122344] USB Mass Storage support registered.
[   15.127532] mice: PS/2 mouse device common for all mice
[   15.133300] input: gpio-keys as /devices/platform/gpio-keys/input/input0
[   15.141357] input: twl4030_pwrbutton as /devices/platform/i2c_omap.1/i2c-1/1-0049/twl4030_pwrbutton/input
/input1
[   15.152221] i2c /dev entries driver
[   15.156524] Linux video capture interface: v2.00
[   15.161560] omap-iommu omap-iommu.0: isp: version 1.1
[   15.168457] vpfe_init
[   15.171417] OMAP Watchdog Timer Rev 0x31: initial timeout 60 sec
[   15.283203] mmci-omap-hs mmci-omap-hs.1: err -16 configuring card detect
[   15.290313] Registered led device: beagleboard::usr0
[   15.295532] Registered led device: beagleboard::usr1
[   15.301300] Registered led device: beagleboard::pmu_stat
[   15.308776] usbcore: registered new interface driver usbhid
[   15.314453] usbhid: USB HID core driver
[   15.318542] Advanced Linux Sound Architecture Driver Version 1.0.21.
[   15.325622] usbcore: registered new interface driver snd-usb-audio
[   15.416748] No device for DAI omap-mcbsp-dai-0
[   15.421203] No device for DAI omap-mcbsp-dai-1
[   15.425720] No device for DAI omap-mcbsp-dai-2
[   15.430206] No device for DAI omap-mcbsp-dai-3
[   15.434722] No device for DAI omap-mcbsp-dai-4
[   15.439208] OMAP3 Beagle SoC init
[   15.444335] asoc: twl4030 <-> omap-mcbsp-dai-0 mapping ok
[   15.457611] ALSA device list:
[   15.460601]   #0: omap3beagle (twl4030)
[   15.464630] oprofile: using arm/armv7
[   15.468597] TCP cubic registered
[   15.471893] NET: Registered protocol family 17
[   15.476409] NET: Registered protocol family 15
[   15.481048] lib80211: common routines for IEEE802.11 drivers
[   15.486816] ThumbEE CPU extension supported.
[   15.491119] Power Management for TI OMAP3.
[   15.496582] Switched to new clocking rate (Crystal/Core/MPU): 26.0/166/600 MHz
[   15.503906] IVA2 clocking rate: 430 MHz
[   15.689086] SmartReflex driver initialized
[   15.703521] VFP support v0.3: implementor 41 architecture 3 part 30 variant c rev 1
[   15.712371] registered taskstats version 1
[   15.718048] fbcvt: 640x480@60: CVT Name - .307M3-R
[   15.739349] Console: switching to colour frame buffer device 80x30
[   15.753997] regulator_init_complete: incomplete constraints, leaving VDAC on
[   15.761535] omap_vout omap_vout: probed for an unknown device
[...........5] Waiting for root device /dev/mmcblk0p2...