Advertisement
Not a member of Pastebin yet?
Sign Up,
it unlocks many cool features!
- CFE version 1.0.37-106.17-1 for BCM96328 (32bit,SP,BE)
- Build Date: 2010-06-28 15:35:56 (wander@broadcom-eu)
- Copyright (C) 2000-2009 Broadcom Corporation.
- HS Serial flash device: name MX25L128, id 0xc218 size 16384KB
- Total Flash size: 16384K with 4096 sectors
- Chip ID: BCM6328B0, MIPS: 320MHz, DDR: 320MHz, Bus: 160MHz
- Main Thread: TP0
- Memory Test Passed
- Total Memory: 67108864 bytes (64MB)
- Boot Address: 0xb8000000
- Board IP address : 192.168.1.1:ffffff00
- Host IP address : 192.168.1.100
- Gateway IP address :
- Run from flash/host (f/h) : f
- Default host run file name : vmlinux
- Default host flash file name : bcm963xx_fs_kernel
- Boot delay (0-9 seconds) : 1
- Board Id (0-7) : 96328avng
- Number of MAC Addresses (1-32) : 10
- Base MAC Address : 50:67:f0:df:a4:78
- PSI Size (1-64) KBytes : 24
- Enable Backup PSI [0|1] : 1
- System Log Size (0-256) KBytes : 16
- Main Thread Number [0|1] : 0
- Serial Number :
- Voice Board Configuration (0-11) :
- *** Press any key to stop auto run (1 seconds) ***
- Auto run second count down: 0
- Booting from only image (0xb8010000) ...
- Code Address: 0x80010000, Entry Address: 0x80014230
- Decompression OK!
- Entry at 0x80014230
- Closing network.
- Disabling Switch ports.
- Flushing Receive Buffers...
- 0 buffers found.
- Closing DMA Channels.
- Starting program at 0x80014230
- Linux version 2.6.30 (lijf@KZ-RDDVM-UBUNTU) (gcc version 4.4.2 (Buildroot 2010.02-git) ) #33 Mon Jun 20 20:58:37 CST 2011
- HS Serial flash device: name MX25L128, id 0xc218 size 16384KB
- 96328avng prom init
- CPU revision is: 0002a075 (Broadcom4350)
- Determined physical RAM map:
- memory: 03f00000 @ 00000000 (usable)
- Zone PFN ranges:
- DMA 0x00000000 -> 0x00001000
- Normal 0x00001000 -> 0x00003f00
- Movable zone start PFN for each node
- early_node_map[1] active PFN ranges
- 0: 0x00000000 -> 0x00003f00
- On node 0 totalpages: 16128
- free_area_init_node: node 0, pgdat 803811c0, node_mem_map 81000000
- DMA zone: 32 pages used for memmap
- DMA zone: 0 pages reserved
- DMA zone: 4064 pages, LIFO batch:0
- Normal zone: 94 pages used for memmap
- Normal zone: 11938 pages, LIFO batch:1
- Built 1 zonelists in Zone order, mobility grouping on. Total pages: 16002
- Kernel command line: root=31:0 ro noinitrd console=ttyS0,115200
- wait instruction: enabled
- Primary instruction cache 32kB, VIPT, 4-way, linesize 16 bytes.
- Primary data cache 32kB, 2-way, VIPT, cache aliases, linesize 16 bytes
- RCU-based detection of stalled CPUs is enabled.
- NR_IRQS:128
- PID hash table entries: 256 (order: 8, 1024 bytes)
- console [ttyS0] enabled
- Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
- Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
- Memory: 59980k/64512k available (2725k kernel code, 4512k reserved, 803k data, 124k init, 0k highmem)
- Calibrating delay loop... 319.48 BogoMIPS (lpj=159744)
- Mount-cache hash table entries: 512
- net_namespace: 816 bytes
- NET: Registered protocol family 16
- Total Flash size: 16384K with 4096 sectors
- registering PCI controller with io_map_base unset
- registering PCI controller with io_map_base unset
- bio: create slab <bio-0> at 0
- SCSI subsystem initialized
- usbcore: registered new interface driver usbfs
- usbcore: registered new interface driver hub
- usbcore: registered new device driver usb
- pci 0000:00:09.0: reg 10 32bit mmio: [0x10002600-0x100026ff]
- pci 0000:00:0a.0: reg 10 32bit mmio: [0x10002500-0x100025ff]
- pci 0000:01:00.0: PME# supported from D0 D3hot
- pci 0000:01:00.0: PME# disabled
- pci 0000:02:00.0: reg 10 64bit mmio: [0x000000-0x003fff]
- pci 0000:02:00.0: supports D1 D2
- pci 0000:01:00.0: PCI bridge, secondary bus 0000:02
- pci 0000:01:00.0: IO window: disabled
- pci 0000:01:00.0: MEM window: 0x10f00000-0x10ffffff
- pci 0000:01:00.0: PREFETCH window: disabled
- PCI: Enabling device 0000:01:00.0 (0000 -> 0002)
- PCI: Setting latency timer of device 0000:01:00.0 to 64
- BLOG v2.1 Initialized
- NET: Registered protocol family 8
- NET: Registered protocol family 20
- NET: Registered protocol family 2
- IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
- TCP established hash table entries: 2048 (order: 2, 16384 bytes)
- TCP bind hash table entries: 2048 (order: 1, 8192 bytes)
- TCP: Hash tables configured (established 2048 bind 2048)
- TCP reno registered
- NET: Registered protocol family 1
- squashfs: version 4.0 (2009/01/31) Phillip Lougher
- squashfs: version 4.0 with LZMA457 ported by BRCM
- fuse init (API version 7.11)
- msgmni has been set to 117
- io scheduler noop registered
- io scheduler deadline registered (default)
- pcieport-driver 0000:01:00.0: device [14e4:6328] has invalid IRQ; check vendor BIOS
- PCI: Setting latency timer of device 0000:01:00.0 to 64
- Driver 'sd' needs updating - please use bus_type methods
- Driver 'sr' needs updating - please use bus_type methods
- PPP generic driver version 2.4.2
- PPP Deflate Compression module registered
- PPP BSD Compression module registered
- NET: Registered protocol family 24
- bcm963xx_mtd driver v1.0
- File system address: 0xb8010100
- ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
- PCI: Enabling device 0000:00:0a.0 (0000 -> 0002)
- PCI: Setting latency timer of device 0000:00:0a.0 to 64
- ehci_hcd 0000:00:0a.0: EHCI Host Controller
- ehci_hcd 0000:00:0a.0: new USB bus registered, assigned bus number 1
- ehci_hcd 0000:00:0a.0: Enabling legacy PCI PM
- ehci_hcd 0000:00:0a.0: irq 50, io mem 0x10002500
- ehci_hcd 0000:00:0a.0: USB f.f started, EHCI 1.00
- usb usb1: configuration #1 chosen from 1 choice
- hub 1-0:1.0: USB hub found
- hub 1-0:1.0: 1 port detected
- ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
- PCI: Enabling device 0000:00:09.0 (0000 -> 0002)
- PCI: Setting latency timer of device 0000:00:09.0 to 64
- ohci_hcd 0000:00:09.0: OHCI Host Controller
- ohci_hcd 0000:00:09.0: new USB bus registered, assigned bus number 2
- ohci_hcd 0000:00:09.0: irq 49, io mem 0x10002600
- usb usb2: configuration #1 chosen from 1 choice
- hub 2-0:1.0: USB hub found
- hub 2-0:1.0: 1 port detected
- usbcore: registered new interface driver usblp
- Initializing USB Mass Storage driver...
- usbcore: registered new interface driver usb-storage
- USB Mass Storage support registered.
- brcmboard: brcm_board_init entry
- Serial: BCM63XX driver $Revision: 3.00 $
- ttyS0 at MMIO 0xb0000100 (irq = 36) is a BCM63XX
- ttyS1 at MMIO 0xb0000120 (irq = 47) is a BCM63XX
- bcmxtmrt: Broadcom BCM6328B0 ATM/PTM Network Device v0.3 Jun 20 2011 19:08:37
- Broadcom Logger v0.1 Sep 28 2010 17:12:39
- Mirror/redirect action on
- u32 classifier
- input device check on
- Actions configured
- TCP cubic registered
- Initializing XFRM netlink socket
- NET: Registered protocol family 17
- NET: Registered protocol family 15
- Initializing MCPD Module
- Ebtables v2.0 registered
- ebt_time registered
- ebt_ftos registered
- ebt_wmm_mark registered
- 802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
- All bugs added by David S. Miller <davem@redhat.com>
- VFS: Mounted root (squashfs filesystem) readonly on device 31:0.
- Freeing unused kernel memory: 124k freed
- init started: BusyBox v1.00 (2011.06.13-13:29+0000) multi-call binary
- BusyBox v1.00 (2011.06.13-13:29+0000) Built-in shell (ash)
- Enter 'help' for a list of built-in commands.
- -sh: can't access tty; job control turned off
- Loading drivers and kernel modules...
- CT_HOTPLUG_MONITOR
- pktflow: module license 'Proprietary' taints kernel.
- Disabling lock debugging due to kernel taint
- Broadcom Packet Flow Cache Char Driver v2.1 Jun 11 2010 15:27:43 Registered<242>
- NBUFF v1.0 Initialized
- Broadcom Packet Flow Cache learning via BLOG enabled.
- Created Proc FS /procfs/fcache
- Broadcom Packet Flow Cache registered with netdev chain
- Constructed Broadcom Packet Flow Cache v2.1 Jun 11 2010 15:27:42
- bcmxtmcfg: bcmxtmcfg_init entry
- adsl: adsl_init entry
- Broadcom BCM6328B0 Ethernet Network Device v0.1 Sep 28 2010 17:12:45
- ETH Init: 180 tx BDs at 0xa3960000
- ETH Init: 400 rx BDs at 0xa3a41000
- ETH Init: 400 rx BDs at 0xa3b4e000
- ######## ethsw_init_table:95 ####### switch_port_phyid[0]=1
- ######## ethsw_init_table:95 ####### switch_port_phyid[1]=2
- ######## ethsw_init_table:95 ####### switch_port_phyid[2]=3
- ######## ethsw_init_table:95 ####### switch_port_phyid[3]=4
- ######## ethsw_init_table:95 ####### switch_port_phyid[4]=24
- /proc/buffer16 created
- dgasp: kerSysRegisterDyingGaspHandler: bcmsw registered
- ===== Found Interface name mapping Fail: use default mapping =====
- eth0: MAC Address: 50:67:F0:DF:A4:79
- eth1: MAC Address: 50:67:F0:DF:A4:78
- eth2: MAC Address: 50:67:F0:DF:A4:7A
- eth3: MAC Address: 50:67:F0:DF:A4:7B
- xxxx: MAC Address: 50:67:F0:DF:A4:78
- xxxx Link UP 1000 mbps full duplex
- message received before monitor task is initialized kerSysSendtoMonitorTask
- PCI: Enabling device 0000:02:00.0 (0000 -> 0002)
- PCI: Setting latency timer of device 0000:02:00.0 to 64
- wl:srom not detected,using main memory mapped srom info(wombo board)
- wl:loading /etc/wlan/bcm4313_map.bin
- wl0: Broadcom BCM4313 802.11 Wireless Controller 5.60.120.3.cpe4.06L02.0
- dgasp: kerSysRegisterDyingGaspHandler: wl0 registered
- p8021ag: p8021ag_init entry
- Broadcom 802.1Q VLAN Interface, v0.1
- usbcore: registered new interface driver usbserial
- USB Serial support registered for generic
- usbcore: registered new interface driver usbserial_generic
- usbserial: USB Serial Driver core
- USB Serial support registered for GSM modem (1-port)
- usbcore: registered new interface driver option
- option: v0.7.2:USB Driver for GSM modems
- ===== Comtrend Release Version A731-406CTL-C01_R04 =====
- device eth0 entered promiscuous mode
- ######## bcm63xx_enet_open:1011 ####### dev->base_addr=0 phyport:0 0
- device eth1 entered promiscuous mode
- ######## bcm63xx_enet_open:1011 ####### dev->base_addr=1 phyport:0 1
- device eth2 entered promiscuous mode
- ######## bcm63xx_enet_open:1011 ####### dev->base_addr=2 phyport:1 2
- device eth3 entered promiscuous mode
- ######## bcm63xx_enet_open:1011 ####### dev->base_addr=3 phyport:2 3
- device wl0 entered promiscuous mode
- WLmngr Daemon is running
- optarg=0 shmId=0
- wlevt_init@107: opened loopback socket 4
- wlevt is ready for new msg...
- br0: port 5(wl0) entering forwarding state
- BcmAdsl_Initialize=0xC019F108, g_pFnNotifyCallback=0xC01D0854
- pSdramPHY=0xA3FFFFF8, 0x8E772 0xD6ADBEEF
- AdslCoreSharedMemInit: shareMemAvailable=491424
- AdslCoreHwReset: AdslOemDataAddr = 0xA3F69564
- Version Number of EOC:406CTL-C01_R04
- dgasp: kerSysRegisterDyingGaspHandler: dsl0 registered
- XTM Init: 400 rx BDs at 0xa2fe2000
- XTM Init: 100 rx BDs at 0xa31de400
- monitor task is initialized pid= 408
- CT_ATCPOLL:error:18.555:getAvailableUsbDongleList:134:Can't open proc file /var/donglemap2
- iptables v1.4.0: can't initialize iptables table `filter': iptables who? (do you need to insmod?)
- Perhaps iptables or your kernel needs to be upgraded.
- iptables v1.4.0: can't initialize iptables table `mangle': iptables who? (do you need to insmod?)
- Perhaps iptables or your kernel needs to be upgraded.
- device wl0 left promiscuous mode
- br0: port 5(wl0) entering disabled state
- device wl0 entered promiscuous mode
- br0: port 5(wl0) entering forwarding state
- wl0.1 (): not using net_device_ops yet
- wl0.2 (): not using net_device_ops yet
- wl0.3 (): not using net_device_ops yet
- br0: port 5(wl0) entering disabled state
- There is no Predefined DevicePin in CFE
- WPS Device PIN = 62327145
- Setting SSID: "Comtrend_A478"
- Setting SSID: "wl0_Guest1"
- Setting SSID: "wl0_Guest2"
- Setting SSID: "wl0_Guest3"
- Chanspec set to 0x2b01
- wlctl: Unsupported
- device wl0 left promiscuous mode
- br0: port 5(wl0) entering disabled state
- device wl0 entered promiscuous mode
- br0: port 5(wl0) entering forwarding state
- Reaped 796
- UPnP daemon is ready to run
- ssk:error:23.240:checkDongleState:190:Wan link(3G) went from up->down, send event msg
- ssk:error:23.241:checkDongleState:220:3G WAN not configured
- /etc/delay_run: 9: m: not found
- eth1 Link UP 100 mbps full duplex
- br0: port 2(eth1) entering forwarding state
- BCM96328 Broadband Router
- Login: root
- Password:
Advertisement
Add Comment
Please, Sign In to add comment
Advertisement