load-log

U-Boot 2009.08 (Apr 29 2012 - 07:16:04)


CPU:   Freescale i.MX53 family 2.1V at 800 MHz

mx53 pll1: 800MHz

mx53 pll2: 600MHz

mx53 pll3: 432MHz

mx53 pll4: 455MHz

ipg clock     : 60000000Hz

ipg per clock : 50000000Hz

uart clock    : 100000000Hz

cspi clock    : 108000000Hz

ahb clock     : 120000000Hz

axi_a clock   : 300000000Hz

axi_b clock   : 200000000Hz

emi_slow clock: 200000000Hz

ddr clock     : 300000000Hz

esdhc1 clock  : 120000000Hz

esdhc2 clock  : 120000000Hz

esdhc3 clock  : 120000000Hz

esdhc4 clock  : 120000000Hz

nfc clock     : 33333333Hz

Board: POR]

Boot Device: NAND

DRAM:  256 MB

NAND:  Manufacturer      : Samsung (0xec)

Device Code       : 0xda

Cell Technology   : SLC

Chip Size         : 256 MiB

Pages per Block   : 64

Page Geometry     : 2048+64

ECC Strength      : 4 bits

ECC Size          : 512 B

Data Setup Time   : 20 ns

Data Hold Time    : 10 ns

Address Setup Time: 20 ns

GPMI Sample Delay : 6 ns

tREA              : Unknown

tRLOH             : Unknown

tRHOH             : Unknown

Description       : K9F2G08U0A

Bad block table found at page 131008, version 0x01

Bad block table found at page 130944, version 0x01

nand_read_bbt: Bad block at 0x0000018a0000

nand_read_bbt: Bad block at 0x000005c00000

nand_read_bbt: Bad block at 0x000008be0000

nand_read_bbt: Bad block at 0x00000a1a0000

nand_read_bbt: Bad block at 0x00000bca0000

nand_read_bbt: Bad block at 0x00000c8a0000

256 MiB

MMC:   FSL_ESDHC: 0

In:    serial

Out:   serial

Err:   serial

Net:   FEC0 [PRIME]

Hit any key to stop autoboot:  3  2  1  0

Loading file "uImage" from mmc device 0:1 (xxa1)

2127832 bytes read

## Booting kernel from Legacy Image at 70800000 ...

   Image Name:   Linux-3.0.66

   Image Type:   ARM Linux Kernel Image (uncompressed)

   Data Size:    2127768 Bytes =  2 MB

   Load Address: 70008000

   Entry Point:  70008000

   Verifying Checksum ... OK

   Loading Kernel Image ... OK

OK


Starting kernel ...


Uncompressing Linux... done, booting the kernel.
[    0.000000] Initializing cgroup subsys cpuset
[    0.000000] Initializing cgroup subsys cpu
[    0.000000] Linux version 3.0.66 (nis@jane) (gcc version 4.6.3 (Gentoo 4.6.3 p1.3, pie-0.5.2) ) #5 Sat Feb 23 19:02:56 OMST 2013
[    0.000000] CPU: ARMv7 Processor [412fc085] revision 5 (ARMv7), cr=10c53c7d
[    0.000000] CPU: VIPT nonaliasing data cache, VIPT aliasing instruction cache
[    0.000000] Machine: Freescale MX53 LOCO Board
[    0.000000] Memory policy: ECC disabled, Data cache writeback
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 65024
[    0.000000] Kernel command line: console=ttymxc0,115200 root=/dev/mmcblk0p1 rw rootwait
[    0.000000] PID hash table entries: 1024 (order: 0, 4096 bytes)
[    0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
[    0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
[    0.000000] Memory: 256MB = 256MB total
[    0.000000] Memory: 255212k/255212k available, 6932k reserved, 0K highmem
[    0.000000] Virtual kernel memory layout:
[    0.000000]     vector  : 0xffff0000 - 0xffff1000   (   4 kB)
[    0.000000]     fixmap  : 0xfff00000 - 0xfffe0000   ( 896 kB)
[    0.000000]     DMA     : 0xffc00000 - 0xffe00000   (   2 MB)
[    0.000000]     vmalloc : 0xd0800000 - 0xf4000000   ( 568 MB)
[    0.000000]     lowmem  : 0xc0000000 - 0xd0000000   ( 256 MB)
[    0.000000]     modules : 0xbf000000 - 0xc0000000   (  16 MB)
[    0.000000]       .init : 0xc0008000 - 0xc0029000   ( 132 kB)
[    0.000000]       .text : 0xc0029000 - 0xc03e9e64   (3844 kB)
[    0.000000]       .data : 0xc03ea000 - 0xc0407728   ( 118 kB)
[    0.000000]        .bss : 0xc040774c - 0xc0489b48   ( 521 kB)
[    0.000000] SLUB: Genslabs=11, HWalign=64, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[    0.000000] NR_IRQS:368 nr_irqs:368 368
[    0.000000] TrustZone Interrupt Controller (TZIC) initialized
[    0.000000] MXC GPIO hardware
[    0.000000] CPU identified as i.MX53, silicon rev 2.1
[    0.000000] sched_clock: 32 bits at 60MHz, resolution 16ns, wraps every 71582ms
[    0.000000] Console: colour dummy device 80x30
[    0.000155] Calibrating delay loop... 795.44 BogoMIPS (lpj=3977216)
[    0.040120] pid_max: default: 32768 minimum: 301
[    0.040259] Security Framework initialized
[    0.040326] Mount-cache hash table entries: 512
[    0.040696] Initializing cgroup subsys cpuacct
[    0.040721] Initializing cgroup subsys freezer
[    0.040761] CPU: Testing write buffer coherency: ok
[    0.040980] hw perfevents: enabled with ARMv7 Cortex-A8 PMU driver, 5 counters available
[    0.041783] devtmpfs: initialized
[    0.042207] kworker/u:0 used greatest stack depth: 6904 bytes left
[    0.047901] NET: Registered protocol family 16
[    0.048676] kworker/u:0 used greatest stack depth: 6728 bytes left
[    0.061688] hw-breakpoint: debug architecture 0x4 unsupported.
[    0.064742] kworker/u:0 used greatest stack depth: 6576 bytes left
[    0.075814] bio: create slab <bio-0> at 0
[    0.077520] SCSI subsystem initialized
[    0.078709] pps_core: LinuxPPS API ver. 1 registered
[    0.078722] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[    0.078918] PTP clock support registered
[    0.081193] Switching to clocksource mxc_timer1
[    0.090291] Switched to NOHz mode on CPU #0
[    0.111820] NetWinder Floating Point Emulator V0.97 (extended precision)
[    0.192425] VFS: Disk quotas dquot_6.5.2
[    0.192810] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[    0.195499] NTFS driver 2.1.30 [Flags: R/W].
[    0.196667] msgmni has been set to 498
[    0.198443] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 251)
[    0.198463] io scheduler noop registered
[    0.198471] io scheduler deadline registered
[    0.198535] io scheduler cfq registered (default)
[    0.200007] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
[    0.202487] Serial: IMX driver
[    0.202667] imx-uart.0: ttymxc0 at MMIO 0x53fbc000 (irq = 31) is a IMX
[    0.560769] console [ttymxc0] enabled
[    0.565789] [drm] Initialized drm 1.1.0 20060810
[    0.573969] mousedev: PS/2 mouse device common for all mice
[    0.580892] cpuidle: using governor ladder
[    0.585227] cpuidle: using governor menu
[    0.589350] sdhci: Secure Digital Host Controller Interface driver
[    0.595568] sdhci: Copyright(c) Pierre Ossman
[    0.600450] mmc0: SDHCI controller on platform [sdhci-esdhc-imx.0] using DMA
[    0.608069] mmc1: SDHCI controller on platform [sdhci-esdhc-imx.2] using DMA
[    0.615390] ThumbEE CPU extension supported.
[    0.620781] drivers/rtc/hctosys.c: unable to open rtc device (rtc0)
[    0.727020] Waiting for root device /dev/mmcblk0p1...
[    0.880227] mmc0: new high speed SD card at address 0260
[    0.886192] mmcblk0: mmc0:0260 SD02G 1.88 GiB
[    0.892490]  mmcblk0: p1 p2
[    1.015420] EXT2-fs (mmcblk0p1): warning: mounting unchecked fs, running e2fsck is recommended
[    1.029072] VFS: Mounted root (ext2 filesystem) on device 179:1.
[    1.037996] devtmpfs: mounted
[    1.041070] Freeing init memory: 132K

INIT: version 2.88 booting

[    1.675453] kbd_mode used greatest stack depth: 6152 bytes left
[    1.709741] loadkeys used greatest stack depth: 5488 bytes left
[    1.716887] init-early.sh used greatest stack depth: 5200 bytes left

   OpenRC 0.11.8 is starting up Gentoo Linux (armv7l)

 * Mounting /proc ...
 [ ok ]
 * Mounting /run ...
 * /run/openrc: creating directory
 * /run/lock: creating directory
 * /run/lock: correcting owner
 * Caching service dependencies ...
Service `netmount' needs non existent service `net'
Service `pydoc-3.2' needs non existent service `net'
Service `sshd' needs non existent service `net'
 [ ok ]
 * Caching service dependencies ...
Service `netmount' needs non existent service `net'
Service `pydoc-3.2' needs non existent service `net'
Service `sshd' needs non existent service `net'
 [ ok ]
 * Clock skew detected with `/etc/init.d'
 * Adjusting mtime of `/run/openrc/deptree' to Fri Feb  8 12:30:42 2013
 * /dev is already mounted
 * Mounting /dev/pts ...
 [ ok ]
 * Mounting /dev/shm ...
 [ ok ]
/etc/init.d/dmesg: line 14:   561 Illegal instruction     dmesg -n$dmesg_level
 * ERROR: dmesg failed to start
 * Mounting /sys ...
 [ ok ]
 * Mounting debug filesystem ...
 [ ok ]
 * Mounting cgroup filesystem ...
 [ ok ]
FATAL: Module unix not found.
 * Cannot load the unix domain socket module
 * Starting udev ...
udevd[638]: error getting socket: Address family not supported by protocol


error initializing udev control socketudevd[638]: error initializing udev control socket

 * start-stop-daemon: failed to start `/sbin/udevd'
 * Failed to start udev
 [ !! ]
 * ERROR: udev failed to start
 * WARNING: clock skew detected!
 * Setting system clock using the hardware clock [UTC] ...
hwclock: Cannot access the Hardware Clock via any known method.
hwclock: Use the --debug option to see the details of our search for an access method.
 * Failed to set the system clock
 [ !! ]
 * Autoloaded 0 module(s)
 * Checking local filesystems  ...
 [ ok ]
 * Remounting filesystems ...
 [ ok ]
 * Updating /etc/mtab ...
 [ ok ]
 * Activating swap devices ...
 [ ok ]
 * Mounting local filesystems ...
 [ ok ]
 * Configuring kernel parameters ...
/etc/init.d/sysctl: line 18:   816 Illegal instruction     sysctl -e -p "${conf}" > /dev/null
 * Some errors were encountered:  
 [ !! ]
 * ERROR: sysctl failed to start
 * /var/lock does not point to /run/lock.
 * Setting /var/lock to point to /run/lock.
 * /var/run does not point to /run.
 * Setting /var/run to point to /run.
 * Creating user login records ...
 [ ok ]
 * Cleaning /var/run ...
 [ ok ]
 * Wiping /tmp directory ...
/etc/init.d/bootmisc: line 17:   870 Illegal instruction     find . -maxdepth 1 ! -name . ! -name lost+found ! -name quota.user ! -name aquota.user ! -name quota.group ! -name aquota.group ! -name journal -exec rm -rf -- {} +
 [ ok ]
/etc/init.d/bootmisc: line 91:   877 Illegal instruction     dmesg > /var/log/dmesg
/etc/init.d/dmesg: line 14:   894 Illegal instruction     dmesg -n$dmesg_level
 * ERROR: dmesg failed to start
 * Setting hostname to localhost ...
 [ ok ]
 * Setting terminal encoding [UTF-8] ...
 [ ok ]
 * Setting keyboard mode [UTF-8] ...
 [ ok ]
 * Loading key mappings [us] ...
 [ ok ]
 * Bringing up interface lo
 *   Caching network module dependencies
 *   127.0.0.1/8 ...
 [ ok ]
 *   Adding routes
 *     127.0.0.0/8 via 127.0.0.1 ...
 [ ok ]
 * Mounting misc binary format filesystem ...
 [ ok ]
 * Loading custom binary format handlers ...
 [ ok ]
 * Activating additional swap space ...
 [ ok ]
 * setting up tmpfiles.d entries ...
 [ ok ]
FATAL: Module unix not found.
 * Cannot load the unix domain socket module
 * Starting udev ...
udevd[1226]: error getting socket: Address family not supported by protocol


error initializing udev control socketudevd[1226]: error initializing udev control socket

 * start-stop-daemon: failed to start `/sbin/udevd'
 * Failed to start udev
 [ !! ]
 * ERROR: udev failed to start
 * Initializing random number generator ...
 [ ok ]
/etc/init.d/urandom: line 15:  1258 Illegal instruction     dd if=/dev/urandom of="$urandom_seed" count=${psz} 2> /dev/null

INIT: Entering runlevel: 3

 * WARNING: clock skew detected!
 * Configuring kernel parameters ...
/etc/init.d/sysctl: line 18:  1284 Illegal instruction     sysctl -e -p "${conf}" > /dev/null
 * Some errors were encountered:  
 [ !! ]
 * ERROR: sysctl failed to start
/etc/init.d/dmesg: line 14:  1303 Illegal instruction     dmesg -n$dmesg_level
 * ERROR: dmesg failed to start
 * ERROR: netmount needs service(s) net
 * Doing udev cleanups
 * Starting local
 [ ok ]
FATAL: Module unix not found.
 * Cannot load the unix domain socket module
 * Starting udev ...
udevd[1390]: error getting socket: Address family not supported by protocol


error initializing udev control socketudevd[1390]: error initializing udev control socket

 * start-stop-daemon: failed to start `/sbin/udevd'
 * Failed to start udev
 [ !! ]
 * ERROR: udev failed to start




This is localhost.O (Linux armv7l 3.0.66) 00:00:16



localhost login: