-- AT91bootstrap Project 3.0 --
-- AT91SAM9M10-EK
-- Compiled: Dec 17 2010 17:24:43 --
-I- Setting: MCK = 133MHz
-I- I cache enabled.
-I- Init DDRAM
-I- Init NAND Flash
-I- Nandflash ID is 0x9510DAEC
-I- Nandflash driver initialized
-I- Size of the whole device in bytes : 0x10000000
-I- Size in bytes of one single block of a device : 0x20000
-I- Number of blocks in the entire device : 0x800
-I- Size of the data area of a page in bytes : 0x800
-I- Number of pages in the entire device : 0x40
-I- Bus width : 8
-I- Copy "" (262144 bytes) from NAND 0x00020000 to 0x73f00000
-I- Jump to 0x73f00000


U-Boot 2010.09 (Nov 19 2010 - 23:40:06)

DRAM:  64 MiB
## Unknown FLASH on Bank 1 - Size = 0x00000000 = 0 MB
Flash: 0 Bytes
NAND:  256 MiB
*** Warning - bad CRC or NAND, using default environment

In:    serial
Out:   serial
Err:   serial
Net:   macb0
Hit any key to stop autoboot:  0

NAND read: device 0 offset 0x80000, size 0x790000
Skipping bad block 0x00100000
Skipping bad block 0x00520000
 7929856 bytes read: OK
## Booting kernel from Legacy Image at 70400000 ...
   Image Name:   Linux Kernel Image
   Image Type:   ARM Linux Kernel Image (gzip compressed)
   Data Size:    2454784 Bytes = 2.3 MiB
   Load Address: 70008000
   Entry Point:  70008000
   Verifying Checksum ... OK
   Uncompressing Kernel Image ... OK

Starting kernel ...

Linux version 2.6.36-rc6 (user@debian) (gcc version 4.2.0 20070413 (prerelease) (CodeSourcery Sourcery G++ Lite 2007q1-10)) #407 Sun Jan 16 20:00:23 EST 201
1
CPU: ARM926EJ-S [41069265] revision 5 (ARMv5TEJ), cr=00053177
CPU: VIVT data cache, VIVT instruction cache
Machine: SK-AT91SAM9G45/M10-XC6SLX
Ignoring unrecognised tag 0x54410009
Memory policy: ECC disabled, Data cache writeback
Clocks: CPU 400 MHz, master 133 MHz, main 12.000 MHz
Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 16256
Kernel command line: console=ttyS0,115200 ubi.mtd=1 root=ubi0:nandfs rw rootfstype=ubifs
PID hash table entries: 256 (order: -2, 1024 bytes)
Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
Memory: 64MB = 64MB total
Memory: 60024k/60024k available, 5512k reserved, 0K highmem
Virtual kernel memory layout:
    vector  : 0xffff0000 - 0xffff1000   (   4 kB)
    fixmap  : 0xfff00000 - 0xfffe0000   ( 896 kB)
    DMA     : 0xffa00000 - 0xffe00000   (   4 MB)
    vmalloc : 0xc4800000 - 0xfee00000   ( 934 MB)
    lowmem  : 0xc0000000 - 0xc4000000   (  64 MB)
    modules : 0xbf000000 - 0xc0000000   (  16 MB)
      .init : 0xc0008000 - 0xc002a000   ( 136 kB)
      .text : 0xc002a000 - 0xc0472000   (4384 kB)
      .data : 0xc0490000 - 0xc04b67e0   ( 154 kB)
Hierarchical RCU implementation.
        Verbose stalled-CPUs detection is disabled.
NR_IRQS:192
AT91: 160 gpio irqs in 5 banks
Console: colour dummy device 80x30
console [ttyS0] enabled
Calibrating delay loop... 199.47 BogoMIPS (lpj=997376)
pid_max: default: 32768 minimum: 301
Mount-cache hash table entries: 512
CPU: Testing write buffer coherency: ok
NET: Registered protocol family 16
bio: create slab <bio-0> at 0
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
i2c-gpio i2c-gpio.0: using pins 52 (SDA) and 53 (SCL)
Advanced Linux Sound Architecture Driver Version 1.0.23.
cfg80211: Calling CRDA to update world regulatory domain
Switching to clocksource pit
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 2048 (order: 2, 16384 bytes)
TCP bind hash table entries: 2048 (order: 1, 8192 bytes)
TCP: Hash tables configured (established 2048 bind 2048)
TCP reno registered
UDP hash table entries: 256 (order: 0, 4096 bytes)
UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
NET: Registered protocol family 1
msgmni has been set to 117
io scheduler noop registered (default)
atmel_lcdfb atmel_lcdfb.0: backlight control is not available
atmel_lcdfb atmel_lcdfb.0: 255KiB frame buffer at 73900000 (mapped at ffa00000)
Console: switching to colour frame buffer device 60x34
atmel_lcdfb atmel_lcdfb.0: fb0: Atmel LCDC at 0x00500000 (mapped at c4814000), irq 23
atmel_usart.0: ttyS0 at MMIO 0xfeffee00 (irq = 1) is a ATMEL_SERIAL
atmel_usart.1: ttyS1 at MMIO 0xfff8c000 (irq = 7) is a ATMEL_SERIAL
atmel_usart.2: ttyS2 at MMIO 0xfff90000 (irq = 8) is a ATMEL_SERIAL
brd: module loaded
loop: module loaded
NAND device: Manufacturer ID: 0xec, Chip ID: 0xda (Samsung NAND 256MiB 3,3V 8-bit)
Scanning device for bad blocks
Bad eraseblock 8 at 0x000000100000
Bad eraseblock 41 at 0x000000520000
Bad eraseblock 307 at 0x000002660000
Bad eraseblock 390 at 0x0000030c0000
Creating 2 MTD partitions on "atmel_nand":
0x000000000000-0x000001000000 : "Boot partition"
0x000001000000-0x000010000000 : "FS partition"
UBI: attaching mtd1 to ubi0
UBI: physical eraseblock size:   131072 bytes (128 KiB)
UBI: logical eraseblock size:    129024 bytes
UBI: smallest flash I/O unit:    2048
UBI: sub-page size:              512
UBI: VID header offset:          512 (aligned 512)
UBI: data offset:                2048
UBI: max. sequence number:       460
UBI: attached mtd1 to ubi0
UBI: MTD device name:            "FS partition"
UBI: MTD device size:            240 MiB
UBI: number of good PEBs:        1918
UBI: number of bad PEBs:         2
UBI: max. allowed volumes:       128
UBI: wear-leveling threshold:    4096
UBI: number of internal volumes: 1
UBI: number of user volumes:     1
UBI: available PEBs:             269
UBI: total number of reserved PEBs: 1649
UBI: number of PEBs reserved for bad PEB handling: 19
UBI: max/mean erase counter: 1/0
UBI: image sequence number:  1576197855
atmel_spi atmel_spi.0: Atmel SPI Controller at 0xfffa4000 (irq 14)
UBI: background thread "ubi_bgt0d" started, PID 892
atmel_spi atmel_spi.1: Atmel SPI Controller at 0xfffa8000 (irq 15)
MACB_mii_bus: probed
eth0: Atmel MACB at 0xfffbc000 irq 25 (00:1f:f2:00:00:00)
eth0: attached PHY driver [Micrel KS8001 or KS8721] (mii_bus:phy_addr=ffffffff:01, irq=-1)
usbcore: registered new interface driver rt2500usb
usbcore: registered new interface driver rt73usb
usbcore: registered new interface driver rt2800usb
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
atmel-ehci atmel-ehci: Atmel EHCI UHP HS
atmel-ehci atmel-ehci: new USB bus registered, assigned bus number 1
atmel-ehci atmel-ehci: irq 22, io mem 0x00800000
atmel-ehci atmel-ehci: USB 2.0 started, EHCI 1.00
usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb1: Product: Atmel EHCI UHP HS
usb usb1: Manufacturer: Linux 2.6.36-rc6 ehci_hcd
usb usb1: SerialNumber: atmel-ehci
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
at91_ohci at91_ohci: AT91 OHCI
at91_ohci at91_ohci: new USB bus registered, assigned bus number 2
at91_ohci at91_ohci: irq 22, io mem 0x00700000
usb usb2: New USB device found, idVendor=1d6b, idProduct=0001
usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb2: Product: AT91 OHCI
usb usb2: Manufacturer: Linux 2.6.36-rc6 ohci_hcd
usb usb2: SerialNumber: at91
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
usbcore: registered new interface driver usbserial
USB Serial support registered for generic
usbcore: registered new interface driver usbserial_generic
usbserial: USB Serial Driver core
USB Serial support registered for FTDI USB Serial Device
usbcore: registered new interface driver ftdi_sio
ftdi_sio: v1.6.0:USB FTDI Serial Converters Driver
USB Serial support registered for moto-modem
usbcore: registered new interface driver moto-modem
USB Serial support registered for GSM modem (1-port)
usbcore: registered new interface driver option
option: v0.7.2:USB Driver for GSM modems
atmel_usba_udc atmel_usba_udc: MMIO registers at 0xfff78000 mapped at c481e000
atmel_usba_udc atmel_usba_udc: FIFO at 0x00600000 mapped at c4900000
mice: PS/2 mouse device common for all mice
setting trigger mode 2 for irq 149 failed (gpio_irq_type+0x0/0x20)
ads7846 spi3.0: trying pin change workaround on irq 149
ads7846 spi3.0: touchscreen, irq 149
input: ADS7843 Touchscreen as /devices/platform/spi_gpio.3/spi3.0/input/input0
rtc-at91sam9 at91_rtt.0: rtc core: registered at91_rtt as rtc0
rtc-at91sam9 at91_rtt.0: rtc0: SET TIME!
i2c /dev entries driver
Linux video capture interface: v2.00
AT91: atmel_isi_init_module
AT91: atmel_isi_probe
atmel_isi atmel_isi: Reading configuration
atmel_isi atmel_isi: video buffer: 155648 bytes at ffa80000 (phys 73180000)
atmel_isi atmel_isi: video buffer: 155648 bytes at ffc80000 (phys 731c0000)
atmel_isi atmel_isi: video buffer: 155648 bytes at ffd00000 (phys 73a80000)
atmel_isi atmel_isi: video buffer: 155648 bytes at ffd80000 (phys 73ac0000)
atmel_isi atmel_isi: capture buffer: 1331200 bytes at ffb00000 (phys 0x73000000)
kfifo_alloc
atmel_isi atmel_isi: Atmel ISI V4L2 device at 0xfffb4000
at_hdmac at_hdmac: Atmel AHB DMA Controller ( cpy slave ), 8 channels
usbcore: registered new interface driver hiddev
usbcore: registered new interface driver usbhid
usbhid: USB HID core driver
atmel_ac97c atmel_ac97c.0: Atmel AC97 controller at 0xc48a0000, irq = 24
ALSA device list:
  #0: Atmel AC97 controller
TCP cubic registered
NET: Registered protocol family 17
lib80211: common routines for IEEE802.11 drivers
rtc-at91sam9 at91_rtt.0: hctosys: unable to read the hardware clock
atmel_mci atmel_mci.0: Using dma0chan0 for DMA transfers
atmel_mci atmel_mci.0: Atmel MCI controller at 0xfff80000 irq 11, 1 slots
atmel_mci atmel_mci.1: Using dma0chan1 for DMA transfers
atmel_mci atmel_mci.1: Atmel MCI controller at 0xfffd0000 irq 29, 1 slots
UBIFS: recovery needed
UBIFS: recovery completed
UBIFS: mounted UBI device 0, volume 0, name "nandfs"
UBIFS: file system size:   208244736 bytes (203364 KiB, 198 MiB, 1614 LEBs)
UBIFS: journal size:       10450944 bytes (10206 KiB, 9 MiB, 81 LEBs)
UBIFS: media format:       w4/r0 (latest is w4/r0)
UBIFS: default compressor: lzo
UBIFS: reserved for root:  4952683 bytes (4836 KiB)
VFS: Mounted root (ubifs filesystem) on device 0:12.
Freeing init memory: 136K
mmc0: host does not support reading read-only switch. assuming write-enable.
mmc0: new high speed SD card at address e624
mmcblk0: mmc0:e624 SU02G 1.84 GiB
 mmcblk0: p1 p2
mkdir: can't create directory '/mnt/mmcblk0': File exists
mount: mounting /dev/mmcblk0 on /mnt/mmcblk0 failed: Invalid argument
mkdir: can't create directory '/mnt/mmcblk0p1': File exists
mkdir: can't create directory '/mnt/mmcblk0p2': File exists
EXT2-fs (mmcblk0p2): warning: mounting unchecked fs, running e2fsck is recommended
Initializing random number generator... done.
Starting wi-fi network ...
Error for wireless request "Set Mode" (8B06) :
    SET failed on device wlan0 ; No such device.
Error for wireless request "Set ESSID" (8B1A) :
    SET failed on device wlan0 ; No such device.
ifconfig: SIOCSIFADDR: No such device
/etc/init.d/rcS: line 28: turn: not found
rm: can't remove '/var/lock/*': No such file or directory
Begin FPGA loading ...
pio mapped
pins preset done
prog pulse done, wait for init
input file size 464303
buffer allocated
file read and closed
start main loop
loaded 453 kB
main loop finished
error while start device, timeout
start sequence completed
buffer freed
ARM-FPGA interconnection tests is beginning:
!!!Make sure downloaded testing FPGA configuration!!!
   ARM address bus test ... FAILED.
      Error detected on 1 address bus bit, read 0xA000A
      Error detected on 2 address bus bit, read 0xA000A
      Error detected on 3 address bus bit, read 0xA000A
      Error detected on 4 address bus bit, read 0xA000A
      Error detected on 5 address bus bit, read 0xA000A
      Error detected on 6 address bus bit, read 0xA000A
      Error detected on 7 address bus bit, read 0xA000A
      Error detected on 8 address bus bit, read 0xA000A
      Error detected on 9 address bus bit, read 0xA000A
      Error detected on 10 address bus bit, read 0xA000A
      Error detected on 11 address bus bit, read 0xA000A
      Error detected on 12 address bus bit, read 0xA000A
      Error detected on 13 address bus bit, read 0xA000A
      Error detected on 14 address bus bit, read 0xA000A
      Error detected on 15 address bus bit, read 0xA000A
      Error detected on 16 address bus bit, read 0xA000A
      Error detected on 17 address bus bit, read 0xA000A
      Error detected on 18 address bus bit, read 0xA000A
      Error detected on 19 address bus bit, read 0xA000A
      Error detected on 20 address bus bit, read 0xA000A
      Error detected on 21 address bus bit, read 0xA000A
      Error detected on 22 address bus bit, read 0xA000A
      Error detected on 23 address bus bit, read 0xA000A
      Error detected on 24 address bus bit, read 0xA000A
   Testing FPGA Block RAM ... FAILED.
      Compute CSUM is 0xD167, real CSUM is 0x61A1.
   MicroBlaze selftest DDR2, waiting ready ... PASSED
      MicroBlaze selftest cycles - 4095
Some ARM-FPGA interconnection tests is FAILED.
USB Host power management utility.
For SK-AT91SAM9G45(M10)-XC6SLX development board.
USB Host-0 turn ON, Host-1 turn ON


Welcome to SK-AT91SAM9G45(M10)-XC6SLX development board!


buildroot login: