Advertisement
Not a member of Pastebin yet?
Sign Up,
it unlocks many cool features!
- BootROM - 1.73
- Booting from NAND flash
- General initialization - Version: 1.0.0
- Detected Device ID 6820
- High speed PHY - Version: 2.0
- Init RD NAS topology Serdes Lane 3 is USB3
- Serdes Lane 4 is SGMII
- board SerDes lanes topology details:
- | Lane # | Speed | Type |
- --------------------------------
- | 0 | 06 | SATA0 |
- | 1 | 05 | PCIe0 |
- | 2 | 06 | SATA1 |
- | 3 | 05 | USB3 HOST1 |
- | 4 | 05 | PCIe1 |
- | 5 | 00 | SGMII2 |
- --------------------------------
- :** Link is Gen1, check the EP capability
- PCIe, Idx 0: Link upgraded to Gen2 based on client cpabilities
- :** Link is Gen1, check the EP capability
- PCIe, Idx 1: remains Gen1
- High speed PHY - Ended Successfully
- DDR3 Training Sequence - Ver TIP-1.26.0
- mvSysEnvGetTopologyUpdateInfo: TWSI Read failed
- DDR3 Training Sequence - Switching XBAR Window to FastPath Window
- DDR3 Training Sequence - Ended Successfully
- Not detected suspend to RAM indication
- BootROM: Image checksum verification PASSED
- __ __ _ _
- | \/ | __ _ _ ____ _____| | |
- | |\/| |/ _` | '__\ \ / / _ \ | |
- | | | | (_| | | \ V / __/ | |
- |_| |_|\__,_|_| \_/ \___|_|_|
- _ _ ____ _
- | | | | | __ ) ___ ___ | |_
- | | | |___| _ \ / _ \ / _ \| __|
- | |_| |___| |_) | (_) | (_) | |_
- \___/ |____/ \___/ \___/ \__|
- ** LOADER **
- U-Boot 2013.01 (Mar 27 2015 - 16:55:31) Marvell version: 2014_T3.0p6
- Boot version : v2.0.13
- Board: RD-NAS-88F6820-DDR3
- SoC: MV88F6820 Rev A0
- running 2 CPUs
- CPU: ARM Cortex A9 MPCore (Rev 1) LE
- CPU 0
- CPU @ 1332 [MHz]
- L2 @ 666 [MHz]
- TClock @ 200 [MHz]
- DDR @ 666 [MHz]
- DDR 32 Bit Width, FastPath Memory Access, DLB Enabled, ECC Disabled
- DRAM: 512 MiB
- Map: Code: 0x1fea9000:0x1ff7632c
- BSS: 0x1ffef6b4
- Stack: 0x1f9a8f20
- Heap: 0x1f9a9000:0x1fea9000
- raise: Signal # 8 caught
- U-ENV offset == 0x200000
- raise: Signal # 8 caught
- U-ENV offset == 0x200000
- U-Boot Environment: 0x00200000:0x00220000 (NAND)
- NAND: 128 MiB
- MMC: mv_sdh: 0
- DEVINFO offset == 0x900000
- U-ENV offset == 0x200000
- U-ENV offset == 0x200000
- S-ENV offset == 0x240000
- #### auto_recovery ####
- [u_env] get auto_recovery == yes
- [u_env] get auto_recovery == yes
- [u_env] get boot_part == 2
- [u_env] get boot_part_ready == 3
- auto_recovery enabled:1, boot_part:2, boot_part_ready:3
- S-ENV offset == 0x240000
- [boot_count_read] block:0x240000, size:128KB, records:64
- [boot_count_read_record] boot_count:3, next_record:29
- [auto_recovery_init] BOOT_COUNT_TO_RECOVERY
- [boot_count_write] erase:0, auto_recovery->block_offset:0x240000 offset=0x24E800
- Updating boot_count ...
- [boot_count_write] offset:0x24E800 , length:2048
- done
- PCI-e 0 (IF 0 - bus 0) Root Complex Interface, Detected Link X1, GEN 2.0
- PCI-e 1 (IF 1 - bus 1) Root Complex Interface, Detected Link X1, GEN 1.1
- USB2.0 0: Host Mode
- USB3.0 1: Host Mode
- USB3.0 0: Host Mode
- Board configuration detected:
- mvEthE6171SwitchBasicInit init
- Net:
- | port | Interface | PHY address |
- |--------|-----------|--------------|
- | egiga0 | RGMII | 0x01 |
- | egiga1 | SGMII | 0x00 |
- egiga0 [PRIME], egiga1
- Saving Environment to NAND...
- U-ENV offset == 0x200000
- Erasing Nand...
- Writing to Nand... U-ENV offset == 0x200000
- U-ENV offset == 0x200000
- done
- #### auto_recovery:1 ####
- auto_recovery_check changes bootcmd: run nandboot
- Hit any key to stop autoboot: 0
- NAND read: device 0 offset 0xa00000, size 0x600000
- 6291456 bytes read: OK
- ## Booting kernel from Legacy Image at 02000000 ...
- Image Name: ARM OpenWrt Linux-4.7
- Created: 2016-07-25 11:32:53 UTC
- Image Type: ARM Linux Kernel Image (uncompressed)
- Data Size: 2665853 Bytes = 2.5 MiB
- Load Address: 00008000
- Entry Point: 00008000
- Verifying Checksum ... OK
- Loading Kernel Image ... OK
- OK
- Starting kernel ...
- [ 0.000000] Booting Linux on physical CPU 0x0
- [ 0.000000] Linux version 4.7.0 (kirkb@c7) (gcc version 5.3.0 (OpenWrt GCC 5.3.0 49876) ) #2 SMP Wed Aug 10 15:56:46 UTC 2016
- [ 0.000000] CPU: ARMv7 Processor [414fc091] revision 1 (ARMv7), cr=10c5387d
- [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
- [ 0.000000] Machine model: Linksys WRT1200AC
- [ 0.000000] Memory policy: Data cache writealloc
- [ 0.000000] percpu: Embedded 13 pages/cpu @dfbcd000 s22720 r8192 d22336 u53248
- [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 130048
- [ 0.000000] Kernel command line: console=ttyS0,115200 root=/dev/mtdblock5 ro rootdelay=1 rootfstype=jffs2 earlyprintk mtdparts=armada-nand:2048K(uboot)ro,256K(u_env),256K(s_env),1m@9m(devinfo),40m@10m(kernel),34m@16m(rootfs),40m@50m(alt_kernel),34m@56m(alt_rootfs),80m@10m(ubifs),-@90m(syscfg)
- [ 0.000000] PID hash table entries: 2048 (order: 1, 8192 bytes)
- [ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
- [ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
- [ 0.000000] Memory: 511552K/524288K available (3979K kernel code, 153K rwdata, 1092K rodata, 2472K init, 299K bss, 12736K reserved, 0K cma-reserved, 0K highmem)
- [ 0.000000] Virtual kernel memory layout:
- [ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB)
- [ 0.000000] fixmap : 0xffc00000 - 0xfff00000 (3072 kB)
- [ 0.000000] vmalloc : 0xe0800000 - 0xff800000 ( 496 MB)
- [ 0.000000] lowmem : 0xc0000000 - 0xe0000000 ( 512 MB)
- [ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB)
- [ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB)
- [ 0.000000] .text : 0xc0008000 - 0xc04fbf94 (5072 kB)
- [ 0.000000] .init : 0xc04fc000 - 0xc0766000 (2472 kB)
- [ 0.000000] .data : 0xc0766000 - 0xc078c440 ( 154 kB)
- [ 0.000000] .bss : 0xc078c440 - 0xc07d7060 ( 300 kB)
- [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
- [ 0.000000] Hierarchical RCU implementation.
- [ 0.000000] RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=2.
- [ 0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2
- [ 0.000000] NR_IRQS:16 nr_irqs:16 16
- [ 0.000000] mvebu_mbus: [Firmware Warn]: deprecated mbus-mvebu Device Tree, suspend/resume will not work
- [ 0.000000] L2C-310 enabling early BRESP for Cortex-A9
- [ 0.000000] L2C-310 full line of zeros enabled for Cortex-A9
- [ 0.000000] L2C-310 D prefetch enabled, offset 1 lines
- [ 0.000000] L2C-310 dynamic clock gating enabled, standby mode enabled
- [ 0.000000] L2C-310 Coherent cache controller enabled, 16 ways, 1024 kB
- [ 0.000000] L2C-310 Coherent: CACHE_ID 0x410054c9, AUX_CTRL 0x56070001
- [ 0.000000] Switching to timer-based delay loop, resolution 40ns
- [ 0.000003] sched_clock: 32 bits at 25MHz, resolution 40ns, wraps every 85899345900ns
- [ 0.000011] clocksource: armada_370_xp_clocksource: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 76450417870 ns
- [ 0.000128] Calibrating delay loop (skipped), value calculated using timer frequency.. 50.00 BogoMIPS (lpj=250000)
- [ 0.000136] pid_max: default: 32768 minimum: 301
- [ 0.000179] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
- [ 0.000185] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
- [ 0.000412] CPU: Testing write buffer coherency: ok
- [ 0.000532] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
- [ 0.000546] Setting up static identity map for 0x8280 - 0x82d8
- [ 0.000626] mvebu-soc-id: MVEBU SoC ID=0x6820, Rev=0x4
- [ 0.000704] mvebu-pmsu: Initializing Power Management Service Unit
- [ 0.001231] Booting CPU 1
- [ 0.001415] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001
- [ 0.001455] Brought up 2 CPUs
- [ 0.001462] SMP: Total of 2 processors activated (100.00 BogoMIPS).
- [ 0.001465] CPU: All CPU(s) started in SVC mode.
- [ 0.001884] devtmpfs: initialized
- [ 0.003929] VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4
- [ 0.004003] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
- [ 0.004021] pinctrl core: initialized pinctrl subsystem
- [ 0.004399] NET: Registered protocol family 16
- [ 0.004985] DMA: preallocated 256 KiB pool for atomic coherent allocations
- [ 0.029903] cpuidle: using governor ladder
- [ 0.032923] mvebu-pmsu: CPU hotplug support is currently broken on Armada 38x: disabling
- [ 0.032933] mvebu-pmsu: CPU idle is currently broken on Armada 38x: disabling
- [ 0.060516] reg-fixed-voltage xhci0-vbus: could not find pctldev for node /soc/internal-regs/pinctrl@18000/xhci0-vbus-pins, deferring probe
- [ 0.060678] SCSI subsystem initialized
- [ 0.060967] usbcore: registered new interface driver usbfs
- [ 0.061004] usbcore: registered new interface driver hub
- [ 0.061032] usbcore: registered new device driver usb
- [ 0.061956] clocksource: Switched to clocksource armada_370_xp_clocksource
- [ 0.062649] NET: Registered protocol family 2
- [ 0.062903] TCP established hash table entries: 4096 (order: 2, 16384 bytes)
- [ 0.062932] TCP bind hash table entries: 4096 (order: 3, 32768 bytes)
- [ 0.062970] TCP: Hash tables configured (established 4096 bind 4096)
- [ 0.062998] UDP hash table entries: 256 (order: 1, 8192 bytes)
- [ 0.063012] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
- [ 0.063090] NET: Registered protocol family 1
- [ 0.067670] futex hash table entries: 512 (order: 3, 32768 bytes)
- [ 0.067855] workingset: timestamp_bits=28 max_order=17 bucket_order=0
- [ 0.070392] squashfs: version 4.0 (2009/01/31) Phillip Lougher
- [ 0.070825] io scheduler noop registered
- [ 0.070831] io scheduler deadline registered (default)
- [ 0.071306] armada-38x-pinctrl f1018000.pinctrl: registered pinctrl driver
- [ 0.071764] irq: Cannot allocate irq_descs @ IRQ44, assuming pre-allocated
- [ 0.072077] irq: Cannot allocate irq_descs @ IRQ76, assuming pre-allocated
- [ 0.072414] mvebu-pcie soc:pcie-controller: PCI host bridge to bus 0000:00
- [ 0.072422] pci_bus 0000:00: root bus resource [io 0x1000-0xfffff]
- [ 0.072428] pci_bus 0000:00: root bus resource [mem 0xe0000000-0xe7ffffff]
- [ 0.072434] pci_bus 0000:00: root bus resource [bus 00-ff]
- [ 0.072678] PCI: bus0: Fast back to back transfers disabled
- [ 0.072685] pci 0000:00:01.0: bridge configuration invalid ([bus 00-00]), reconfiguring
- [ 0.072692] pci 0000:00:02.0: bridge configuration invalid ([bus 00-00]), reconfiguring
- [ 0.072944] PCI: bus1: Fast back to back transfers disabled
- [ 0.073225] PCI: bus2: Fast back to back transfers disabled
- [ 0.073289] pci 0000:00:01.0: BAR 8: assigned [mem 0xe0000000-0xe01fffff]
- [ 0.073296] pci 0000:00:02.0: BAR 8: assigned [mem 0xe0200000-0xe03fffff]
- [ 0.073304] pci 0000:01:00.0: BAR 0: assigned [mem 0xe0000000-0xe00fffff 64bit pref]
- [ 0.073315] pci 0000:01:00.0: BAR 2: assigned [mem 0xe0100000-0xe01fffff 64bit pref]
- [ 0.073325] pci 0000:00:01.0: PCI bridge to [bus 01]
- [ 0.073331] pci 0000:00:01.0: bridge window [mem 0xe0000000-0xe01fffff]
- [ 0.073340] pci 0000:02:00.0: BAR 0: assigned [mem 0xe0200000-0xe02fffff 64bit pref]
- [ 0.073351] pci 0000:02:00.0: BAR 2: assigned [mem 0xe0300000-0xe03fffff 64bit pref]
- [ 0.073362] pci 0000:00:02.0: PCI bridge to [bus 02]
- [ 0.073367] pci 0000:00:02.0: bridge window [mem 0xe0200000-0xe03fffff]
- [ 0.073488] mv_xor f1060800.xor: Marvell shared XOR driver
- [ 0.112505] mv_xor f1060800.xor: Marvell XOR (Descriptor Mode): ( xor cpy intr )
- [ 0.112602] mv_xor f1060900.xor: Marvell shared XOR driver
- [ 0.152491] mv_xor f1060900.xor: Marvell XOR (Descriptor Mode): ( xor cpy intr )
- [ 0.152688] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
- [ 0.153072] console [ttyS0] disabled
- [ 0.173160] f1012000.serial: ttyS0 at MMIO 0xf1012000 (irq = 21, base_baud = 12500000) is a 16550A
- [ 0.882649] console [ttyS0] enabled
- [ 0.886531] ahci-mvebu f10a8000.sata: AHCI 0001.0000 32 slots 2 ports 6 Gbps 0x3 impl platform mode
- [ 0.895633] ahci-mvebu f10a8000.sata: flags: 64bit ncq sntf led only pmp fbs pio slum part sxs
- [ 0.905191] scsi host0: ahci-mvebu
- [ 0.908792] scsi host1: ahci-mvebu
- [ 0.912328] ata1: SATA max UDMA/133 mmio [mem 0xf10a8000-0xf10a9fff] port 0x100 irq 41
- [ 0.920279] ata2: SATA max UDMA/133 mmio [mem 0xf10a8000-0xf10a9fff] port 0x180 irq 41
- [ 0.928660] pxa3xx-nand f10d0000.flash: This platform can't do DMA on this device
- [ 0.936448] nand: device found, Manufacturer ID: 0x01, Chip ID: 0xf1
- [ 0.942837] nand: AMD/Spansion S34ML01G2
- [ 0.946776] nand: 128 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64
- [ 0.954384] pxa3xx-nand f10d0000.flash: ECC strength 16, ECC step size 2048
- [ 0.961572] Bad block table found at page 65472, version 0x01
- [ 0.967697] Bad block table found at page 65408, version 0x01
- [ 0.973759] 10 ofpart partitions found on MTD device pxa3xx_nand-0
- [ 0.979965] Creating 10 MTD partitions on "pxa3xx_nand-0":
- [ 0.985484] 0x000000000000-0x000000200000 : "u-boot"
- [ 0.990895] 0x000000200000-0x000000240000 : "u_env"
- [ 0.996178] 0x000000240000-0x000000280000 : "s_env"
- [ 1.001448] 0x000000900000-0x000000a00000 : "devinfo"
- [ 1.006911] 0x000000a00000-0x000003200000 : "kernel1"
- [ 1.012484] 0x000001000000-0x000003200000 : "rootfs1"
- [ 1.018037] 0x000003200000-0x000005a00000 : "kernel2"
- [ 1.023619] 0x000003800000-0x000005a00000 : "rootfs2"
- [ 1.029143] 0x000005a00000-0x000008000000 : "syscfg"
- [ 1.034608] 0x000000280000-0x000000900000 : "unused_area"
- [ 1.040876] libphy: Fixed MDIO Bus: probed
- [ 1.045120] libphy: orion_mdio_bus: probed
- [ 1.049397] mvneta_bm f10c8000.bm: Buffer Manager for network controller enabled
- [ 1.058604] mvneta f1070000.ethernet eth0: Using hardware mac address c0:56:27:6d:a3:0b
- [ 1.068037] mvneta f1034000.ethernet eth1: Using random mac address b2:45:43:43:55:c1
- [ 1.075978] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
- [ 1.082542] ehci-pci: EHCI PCI platform driver
- [ 1.087039] ehci-orion: EHCI orion driver
- [ 1.091158] orion-ehci f1058000.usb: EHCI Host Controller
- [ 1.096600] orion-ehci f1058000.usb: new USB bus registered, assigned bus number 1
- [ 1.104278] orion-ehci f1058000.usb: irq 37, io mem 0xf1058000
- [ 1.121943] orion-ehci f1058000.usb: USB 2.0 started, EHCI 1.00
- [ 1.128235] hub 1-0:1.0: USB hub found
- [ 1.132029] hub 1-0:1.0: 1 port detected
- [ 1.136422] usbcore: registered new interface driver usb-storage
- [ 1.142655] armada38x-rtc f10a3800.rtc: rtc core: registered f10a3800.rtc as rtc0
- [ 1.150314] i2c /dev entries driver
- [ 1.165526] orion_wdt: Initial timeout 171 sec
- [ 1.173507] marvell-cesa f1090000.crypto: CESA device successfully registered
- [ 1.181310] NET: Registered protocol family 10
- [ 1.186286] NET: Registered protocol family 17
- [ 1.190766] bridge: automatic filtering via arp/ip/ip6tables has been deprecated. Update your scripts to load br_netfilter if you need this.
- [ 1.203439] 8021q: 802.1Q VLAN Support v1.8
- [ 1.207698] Registering SWP/SWPB emulation handler
- [ 1.213242] xhci-hcd f10f8000.usb3: xHCI Host Controller
- [ 1.218601] xhci-hcd f10f8000.usb3: new USB bus registered, assigned bus number 2
- [ 1.226248] xhci-hcd f10f8000.usb3: hcc params 0x0a000990 hci version 0x100 quirks 0x00010010
- [ 1.234850] xhci-hcd f10f8000.usb3: irq 43, io mem 0xf10f8000
- [ 1.241012] hub 2-0:1.0: USB hub found
- [ 1.242132] ata2: SATA link down (SStatus 0 SControl 300)
- [ 1.242157] ata1: SATA link down (SStatus 0 SControl 300)
- [ 1.255648] hub 2-0:1.0: 1 port detected
- [ 1.259697] xhci-hcd f10f8000.usb3: xHCI Host Controller
- [ 1.265045] xhci-hcd f10f8000.usb3: new USB bus registered, assigned bus number 3
- [ 1.272633] usb usb3: We don't know the algorithms for LPM for this host, disabling LPM.
- [ 1.281046] hub 3-0:1.0: USB hub found
- [ 1.284842] hub 3-0:1.0: 1 port detected
- [ 1.288917] armada38x-rtc f10a3800.rtc: setting system clock to 2105-12-17 07:08:45 UTC (4290476925)
- [ 1.300222] Freeing unused kernel memory: 2472K (c04fc000 - c0766000)
- [ 1.306714] This architecture does not have kernel memory protection.
- [ 1.333701] ubi0: attaching mtd5
- [ 1.401865] ubi0 error: ubi_attach [ubi]: bad image sequence number 1832218409 in PEB 186, expected 1759407395
- [ 1.411916] Erase counter header dump:
- [ 1.415682] magic 0x55424923
- [ 1.419444] version 1
- [ 1.422424] ec 1
- [ 1.425401] vid_hdr_offset 2048
- [ 1.428639] data_offset 4096
- [ 1.431878] image_seq 1832218409
- [ 1.435644] hdr_crc 0xf06edc3f
- [ 1.439405] erase counter header hexdump:
- [ 1.443551] ubi0 error: ubi_attach_mtd_dev [ubi]: failed to attach mtd5, error -22
- [ 1.451161] UBI error: cannot attach mtd5
- [ 1.455093] UBI error: cannot initialize UBI, error -22[ 1.514366] ubi0: attaching mtd5
- [ 1.582510] ubi0 error: ubi_attach [ubi]: bad image sequence number 1832218409 in PEB 186, expected 1759407395
- [ 1.592562] Erase counter header dump:
- [ 1.596325] magic 0x55424923
- [ 1.600087] version 1
- [ 1.603068] ec 1
- [ 1.606045] vid_hdr_offset 2048
- [ 1.609284] data_offset 4096
- [ 1.612526] image_seq 1832218409
- [ 1.616288] hdr_crc 0xf06edc3f
- [ 1.620050] erase counter header hexdump:
- [ 1.624195] ubi0 error: ubi_attach_mtd_dev [ubi]: failed to attach mtd5, error -22
- [ 1.631804] UBI error: cannot attach mtd5
- [ 1.635735] UBI error: cannot initialize UBI, error -22modprobe: 'ubi.ko': invalid parameter
- Error in /init: ubi
- -install: applet not found
- BusyBox v1.25.0 () built-in shell (ash)
- sh: can't access tty; job control turned off
- #
Advertisement
Add Comment
Please, Sign In to add comment
Advertisement