Advertisement
Not a member of Pastebin yet?
Sign Up,
it unlocks many cool features!
- U-Boot SPL 2016.03-rc2-armbian (Feb 19 2016 - 11:56:49)
- DRAM: 512 MiB
- Trying to boot from MMC
- U-Boot 2016.03-rc2-armbian (Feb 19 2016 - 11:56:49 -0500) Allwinner Technology
- CPU: Allwinner H3 (SUN8I)
- I2C: ready
- DRAM: 512 MiB
- MMC: SUNXI SD/MMC: 0
- *** Warning - bad CRC, using default environment
- In: serial
- Out: serial
- Err: serial
- Net: No ethernet found.
- starting USB...
- No controllers found
- Hit any key to stop autoboot: 2 1 0
- switch to partitions #0, OK
- mmc0 is current device
- Scanning mmc 0:1...
- Found U-Boot script /boot/boot.scr
- 2139 bytes read in 310 ms (5.9 KiB/s)
- ## Executing script at 43100000
- gpio: pin PA15 (gpio 15) value is 1
- ** File not found /boot/.next **
- ** Unrecognized filesystem type **
- ** File not found .next **
- 35832 bytes read in 707 ms (48.8 KiB/s)
- 4768728 bytes read in 4929 ms (944.3 KiB/s)
- Kernel image @ 0x48000000 [ 0x000000 - 0x48c3d8 ]
- Using machid 0x1029 from environment
- Starting kernel ...
- [sun8i_fixup]: From boot, get meminfo:
- Start: 0x40000000
- Size: 512MB
- ion_carveout reserve: 160m@0 256m@0 130m@1 200m@1
- ion_reserve_common: ion reserve: [0x56000000, 0x60000000]!
- [ 0.000000] Booting Linux on physical CPU 0
- [ 0.000000] Initializing cgroup subsys cpuset
- [ 0.000000] Initializing cgroup subsys cpu
- [ 0.000000] Linux version 3.4.110-sun8i (root@makearmbian) (gcc version 4.8.2 (Ubuntu/Linaro 4.8.2-16ubuntu4) ) #6 SMP PREEMPT Fri Feb 19 12:00:23 EST 2016
- [ 0.000000] CPU: ARMv7 Processor [410fc075] revision 5 (ARMv7), cr=10c5387d
- [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
- [ 0.000000] Machine: sun8i
- [ 0.000000] cma: CMA: reserved 160 MiB at 56000000
- [ 0.000000] Memory policy: ECC disabled, Data cache writealloc
- [ 0.000000] On node 0 totalpages: 131072
- [ 0.000000] free_area_init_node: node 0, pgdat c09bfcc0, node_mem_map c0a9e000
- [ 0.000000] Normal zone: 1152 pages used for memmap
- [ 0.000000] Normal zone: 0 pages reserved
- [ 0.000000] Normal zone: 129920 pages, LIFO batch:31
- [ 0.000000] script_init enter!
- [ 0.000000] script_init exit!
- [ 0.000000] PERCPU: Embedded 8 pages/cpu @c0f30000 s11904 r8192 d12672 u32768
- [ 0.000000] pcpu-alloc: s11904 r8192 d12672 u32768 alloc=8*4096
- [ 0.000000] pcpu-alloc: [0] 0 [0] 1 [0] 2 [0] 3
- [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 129920
- [ 0.000000] Kernel command line: console=ttyS0,115200 root=/dev/mmcblk0p1 rootwait rootfstype=ext4 cgroup-enable=memory swapaccount=1 sunxi_ve_mem_reserve=0 sunxi_g2d_mem_reserve=0 sunxi_no_mali_mem_reserve sunxi_fb_mem_reserve=16 hdmi.audio=EDID:0 panic=10 consoleblank=0 enforcing=0 loglevel=8
- [ 0.000000] PID hash table entries: 2048 (order: 1, 8192 bytes)
- [ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
- [ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
- [ 0.000000] allocated 1048576 bytes of page_cgroup
- [ 0.000000] please try 'cgroup_disable=memory' option if you don't want memory cgroups
- [ 0.000000] Memory: 512MB = 512MB total
- [ 0.000000] Memory: 342764k/342764k available, 181524k reserved, 0K highmem
- [ 0.000000] Virtual kernel memory layout:
- [ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB)
- [ 0.000000] fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB)
- [ 0.000000] vmalloc : 0xe0800000 - 0xff000000 ( 488 MB)
- [ 0.000000] lowmem : 0xc0000000 - 0xe0000000 ( 512 MB)
- [ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB)
- [ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB)
- [ 0.000000] .text : 0xc0008000 - 0xc08fd77c (9174 kB)
- [ 0.000000] .init : 0xc08fe000 - 0xc094ae80 ( 308 kB)
- [ 0.000000] .data : 0xc094c000 - 0xc09c4b10 ( 483 kB)
- [ 0.000000] .bss : 0xc09c52c4 - 0xc0a9d2d8 ( 865 kB)
- [ 0.000000] Preemptible hierarchical RCU implementation.
- [ 0.000000] Additional per-CPU info printed with stalls.
- [ 0.000000] NR_IRQS:544
- [ 0.000000] Architected local timer running at 24.00MHz.
- [ 0.000000] Switching to timer-based delay loop
- [ 0.000000] sched_clock: 32 bits at 24MHz, resolution 41ns, wraps every 178956ms
- [ 0.000000] Console: colour dummy device 80x30
- [ 0.000199] Calibrating delay loop (skipped), value calculated using timer frequency.. 4800.00 BogoMIPS (lpj=24000000)
- [ 0.000225] pid_max: default: 32768 minimum: 301
- [ 0.000571] Mount-cache hash table entries: 512
- [ 0.001592] Initializing cgroup subsys cpuacct
- [ 0.001609] Initializing cgroup subsys memory
- [ 0.001657] Initializing cgroup subsys devices
- [ 0.001670] Initializing cgroup subsys freezer
- [ 0.001682] Initializing cgroup subsys blkio
- [ 0.001707] Initializing cgroup subsys perf_event
- [ 0.001763] CPU: Testing write buffer coherency: ok
- [ 0.001813] ftrace: allocating 25140 entries in 74 pages
- [ 0.030290] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
- [ 0.030309] [sunxi_smp_prepare_cpus] enter
- [ 0.030347] Setting up static identity map for 0x40676de8 - 0x40676e40
- [ 0.031279] CPU1: Booted secondary processor
- [ 0.031279] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001
- [ 0.031412] CPU2: Booted secondary processor
- [ 0.031412] CPU2: thread -1, cpu 2, socket 0, mpidr 80000002
- [ 0.031412] CPU3: Booted secondary processor
- [ 0.031412] CPU3: thread -1, cpu 3, socket 0, mpidr 80000003
- [ 0.040191] Brought up 4 CPUs
- [ 0.040209] SMP: Total of 4 processors activated (19200.00 BogoMIPS).
- [ 0.040934] devtmpfs: initialized
- [ 0.044351] wakeup src cnt is : 1.
- [ 0.044364] [exstandby]leave extended_standby_enable_wakeup_src : event 0x800000
- [ 0.044376] [exstandby]leave extended_standby_enable_wakeup_src : wakeup_gpio_map 0x0
- [ 0.044388] [exstandby]leave extended_standby_enable_wakeup_src : wakeup_gpio_group 0x40
- [ 0.044401] sunxi pm init
- [ 0.044548] pinctrl core: initialized pinctrl subsystem
- [ 0.054179] NET: Registered protocol family 16
- [ 0.055131] DMA: preallocated 2048 KiB pool for atomic coherent allocations
- [ 0.055131] script_sysfs_init success
- [ 0.055131] sunxi_dump_init success
- [ 0.055131] gpiochip_add: registered GPIOs 0 to 383 on device: sunxi-pinctrl
- [ 0.055131] sunxi-pinctrl sunxi-pinctrl: initialized sunXi PIO driver
- [ 0.055131] hw-breakpoint: found 5 (+1 reserved) breakpoint and 4 watchpoint registers.
- [ 0.055131] hw-breakpoint: maximum watchpoint size is 8 bytes.
- [ 0.055131] script config pll_video to 297 Mhz
- [ 0.055131] script config pll_de to 864 Mhz
- [ 0.055131] script config pll_ve to 402 Mhz
- [ 0.055131] sunxi_default_clk_init
- [ 0.055131] try to set pll6ahb1 to 200000000
- [ 0.055131] try to set ahb clk source to pll6ahb1
- [ 0.055131] set ahb clk source to pll6ahb1
- [ 0.055131] try to set ahb1 to 200000000
- [ 0.055131] try to set apb1 to 100000000
- [ 0.055610] ===fe3o4==== sunxi_root_procfs_attach ret:0
- [ 0.061203] bio: create slab <bio-0> at 0
- [ 0.061203] [ARISC] :sunxi-arisc driver v1.04
- [ 0.076639] [ARISC] :arisc version: [v0.1.34]
- [ 0.164640] [ARISC] :sunxi-arisc driver v1.04 startup succeeded
- [ 0.170445] SCSI subsystem initialized
- [ 0.170654] usbcore: registered new interface driver usbfs
- [ 0.170731] usbcore: registered new interface driver hub
- [ 0.170765] usbcore: registered new device driver usb
- [ 0.170765] twi_chan_cfg()335 - [twi0] has no twi_regulator.
- [ 0.170765] twi_chan_cfg()335 - [twi1] has no twi_regulator.
- [ 0.170765] twi_chan_cfg()335 - [twi2] has no twi_regulator.
- [ 0.170765] Linux video capture interface: v2.00
- [ 0.170783] Advanced Linux Sound Architecture Driver Version 1.0.25.
- [ 0.171535] cfg80211: Calling CRDA to update world regulatory domain
- [ 0.171604] Switching to clocksource arch_sys_counter
- [ 0.184064] FS-Cache: Loaded
- [ 0.184352] CacheFiles: Loaded
- [ 0.195659] NET: Registered protocol family 2
- [ 0.207807] IP route cache hash table entries: 4096 (order: 2, 16384 bytes)
- [ 0.208374] TCP established hash table entries: 16384 (order: 5, 131072 bytes)
- [ 0.208622] TCP bind hash table entries: 16384 (order: 5, 196608 bytes)
- [ 0.208881] TCP: Hash tables configured (established 16384 bind 16384)
- [ 0.208893] TCP: reno registered
- [ 0.208906] UDP hash table entries: 256 (order: 1, 8192 bytes)
- [ 0.208932] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
- [ 0.209268] NET: Registered protocol family 1
- [ 0.209657] RPC: Registered named UNIX socket transport module.
- [ 0.209671] RPC: Registered udp transport module.
- [ 0.209680] RPC: Registered tcp transport module.
- [ 0.209689] RPC: Registered tcp NFSv4.1 backchannel transport module.
- [ 0.210317] hw perfevents: enabled with ARMv7 Cortex_A7 PMU driver, 5 counters available
- [ 0.210423] sunxi_reg_init enter
- [ 0.211239] audit: initializing netlink socket (disabled)
- [ 0.211283] type=2000 audit(0.210:1): initialized
- [ 0.213087] squashfs: version 4.0 (2009/01/31) Phillip Lougher
- [ 0.213187] NFS: Registering the id_resolver key type
- [ 0.213590] Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
- [ 0.214337] NTFS driver 2.1.30 [Flags: R/W].
- [ 0.214651] fuse init (API version 7.18)
- [ 0.215412] Btrfs loaded
- [ 0.215438] msgmni has been set to 989
- [ 0.216581] io scheduler noop registered
- [ 0.216594] io scheduler deadline registered
- [ 0.216680] io scheduler cfq registered (default)
- [ 0.217165] [DISP]disp_module_init
- [ 0.225259] [DISP] Fb_map_kernel_logo,line:931:Fb_map_kernel_logo failed!
- [ 0.242639] Console: switching to colour frame buffer device 160x45
- [ 0.260973] [DISP]disp_module_init finish
- [ 0.261201] sw_uart_get_devinfo()1503 - uart0 has no uart_regulator.
- [ 0.261519] uart0: ttyS0 at MMIO 0x1c28000 (irq = 32) is a SUNXI
- [ 0.261534] sw_uart_pm()890 - uart0 clk is already enable
- [ 0.261554] sw_console_setup()1233 - console setup baud 115200 parity n bits 8, flow n
- [ 0.453822] console [ttyS0] enabled
- [ 0.645533] sunxi_cmatest_init enter
- [ 0.770070] sunxi_cmatest_init success
- [ 0.774530] loop: module loaded
- [ 0.836661] sunxi_spi_chan_cfg()1355 - [spi-0] has no spi_regulator.
- [ 0.836675] sunxi_spi_chan_cfg()1355 - [spi-1] has no spi_regulator.
- [ 0.836710] tun: Universal TUN/TAP device driver, 1.6
- [ 0.836718] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
- [ 0.837687] PPP generic driver version 2.4.2
- [ 0.837878] PPP BSD Compression module registered
- [ 0.837888] PPP Deflate Compression module registered
- [ 0.838718] PPP MPPE Compression module registered
- [ 0.838731] NET: Registered protocol family 24
- [ 0.838791] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
- [ 0.858870] sunxi-ehci sunxi-ehci.1: SW USB2.0 'Enhanced' Host Controller (EHCI) Driver
- [ 0.858903] sunxi-ehci sunxi-ehci.1: new USB bus registered, assigned bus number 1
- [ 0.932298] sunxi-ehci sunxi-ehci.1: irq 104, io mem 0xf1c1a000
- [ 1.140037] sunxi-ehci sunxi-ehci.1: USB 0.0 started, EHCI 1.00
- [ 1.254298] hub 1-0:1.0: USB hub found
- [ 1.258470] hub 1-0:1.0: 1 port detected
- [ 1.283227] sunxi-ehci sunxi-ehci.2: SW USB2.0 'Enhanced' Host Controller (EHCI) Driver
- [ 1.292141] sunxi-ehci sunxi-ehci.2: new USB bus registered, assigned bus number 2
- [ 1.301113] sunxi-ehci sunxi-ehci.2: irq 106, io mem 0xf1c1b000
- [ 1.320043] sunxi-ehci sunxi-ehci.2: USB 0.0 started, EHCI 1.00
- [ 1.327138] hub 2-0:1.0: USB hub found
- [ 1.331325] hub 2-0:1.0: 1 port detected
- [ 1.336077] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
- [ 1.363006] sunxi-ohci sunxi-ohci.1: SW USB2.0 'Open' Host Controller (OHCI) Driver
- [ 1.371534] sunxi-ohci sunxi-ohci.1: new USB bus registered, assigned bus number 3
- [ 1.379958] sunxi-ohci sunxi-ohci.1: irq 105, io mem 0xf1c1a400
- [ 1.444554] hub 3-0:1.0: USB hub found
- [ 1.448725] hub 3-0:1.0: 1 port detected
- [ 1.473463] sunxi-ohci sunxi-ohci.2: SW USB2.0 'Open' Host Controller (OHCI) Driver
- [ 1.481988] sunxi-ohci sunxi-ohci.2: new USB bus registered, assigned bus number 4
- [ 1.490425] sunxi-ohci sunxi-ohci.2: irq 107, io mem 0xf1c1b400
- [ 1.554592] hub 4-0:1.0: USB hub found
- [ 1.558760] hub 4-0:1.0: 1 port detected
- [ 1.563498] Initializing USB Mass Storage driver...
- [ 1.569056] usbcore: registered new interface driver usb-storage
- [ 1.575740] USB Mass Storage support registered.
- [ 1.580921] usbcore: registered new interface driver ums-alauda
- [ 1.587525] usbcore: registered new interface driver ums-cypress
- [ 1.594251] usbcore: registered new interface driver ums-datafab
- [ 1.600971] usbcore: registered new interface driver ums_eneub6250
- [ 1.607866] usbcore: registered new interface driver ums-freecom
- [ 1.614587] usbcore: registered new interface driver ums-isd200
- [ 1.621215] usbcore: registered new interface driver ums-jumpshot
- [ 1.628012] usbcore: registered new interface driver ums-karma
- [ 1.634536] usbcore: registered new interface driver ums-onetouch
- [ 1.641366] usbcore: registered new interface driver ums-realtek
- [ 1.648068] usbcore: registered new interface driver ums-sddr09
- [ 1.654692] usbcore: registered new interface driver ums-sddr55
- [ 1.661377] usbcore: registered new interface driver ums-usbat
- [ 1.668178] file system registered
- [ 1.673756] android_usb gadget: Mass Storage Function, version: 2009/09/11
- [ 1.681423] android_usb gadget: Number of LUNs=3
- [ 1.686548] lun0: LUN: removable file: (no medium)
- [ 1.691974] lun1: LUN: removable file: (no medium)
- [ 1.697385] lun2: LUN: removable file: (no medium)
- [ 1.703126] android_usb gadget: android_usb ready
- [ 1.708564] uinput result 0 , vmouse_init
- [ 1.713833] mousedev: PS/2 mouse device common for all mice
- [ 1.720254] ls_fetch_sysconfig_para: type err device_used = 0.
- [ 1.726918] =========script_get_err============
- [ 1.731958] ltr_init: ls_fetch_sysconfig_para err.
- [ 1.737566] [RTC] WARNING: Rtc time will be wrong!!
- [ 1.743274] sunxi-rtc sunxi-rtc: rtc core: registered sunxi-rtc as rtc0
- [ 1.750677] i2c /dev entries driver
- [ 1.754804] IR RC5(x) protocol handler initialized
- [ 1.760255] sunxi cedar version 0.1
- [ 1.764257] [cedar]: install start!!!
- [ 1.768505] [cedar]: install end!!!
- [ 1.772628] sunxi_i2c_do_xfer()980 - [i2c0] incomplete xfer (status: 0x20, dev addr: 0x18)
- [ 1.781988] sunxi_i2c_do_xfer()980 - [i2c0] incomplete xfer (status: 0x20, dev addr: 0x19)
- [ 1.791336] sunxi_i2c_do_xfer()980 - [i2c0] incomplete xfer (status: 0x20, dev addr: 0x1a)
- [ 1.800684] sunxi_i2c_do_xfer()980 - [i2c0] incomplete xfer (status: 0x20, dev addr: 0x29)
- [ 1.810016] sunxi_i2c_do_xfer()980 - [i2c0] incomplete xfer (status: 0x20, dev addr: 0x2a)
- [ 1.819345] sunxi_i2c_do_xfer()980 - [i2c0] incomplete xfer (status: 0x20, dev addr: 0x2b)
- [ 1.828691] sunxi_i2c_do_xfer()980 - [i2c0] incomplete xfer (status: 0x20, dev addr: 0x4c)
- [ 1.838036] sunxi_i2c_do_xfer()980 - [i2c0] incomplete xfer (status: 0x20, dev addr: 0x4d)
- [ 1.847380] sunxi_i2c_do_xfer()980 - [i2c0] incomplete xfer (status: 0x20, dev addr: 0x4e)
- [ 1.856571] sunxi_wdt_init_module: sunxi WatchDog Timer Driver v1.0
- [ 1.863697] sunxi_wdt_probe: devm_ioremap return wdt_reg 0xf1c20ca0, res->start 0x01c20ca0, res->end 0x01c20cbf
- [ 1.874868] sunxi_wdt_probe: initialized (g_timeout=16s, g_nowayout=0)
- [ 1.882328] wdt_enable, write reg 0xf1c20cb8 val 0x00000000
- [ 1.888512] timeout_to_interv, line 167
- [ 1.892778] interv_to_timeout, line 189
- [ 1.897032] wdt_set_tmout, write 0x000000b0 to mode reg 0xf1c20cb8, actual timeout 16 sec
- [ 1.906519] device-mapper: ioctl: 4.22.0-ioctl (2011-10-19) initialised: dm-devel@redhat.com
- [ 1.915987] [cpu_freq] ERR:get cpu extremity frequency from sysconfig failed, use max_freq
- [ 1.925472] [mmc]: SD/MMC/SDIO Host Controller Driver(v1.109 2014-12-4 20:51) Compiled in Feb 19 2016 at 11:58:42
- [ 1.936904] [mmc]: get mmc0's sdc_power is null!
- [ 1.942057] [mmc]: get mmc1's sdc_power is null!
- [ 1.947179] [mmc]: get mmc1's 2xmode ok, val = 1
- [ 1.952313] [mmc]: get mmc1's ddrmode ok, val = 1
- [ 1.957538] [mmc]: MMC host used card: 0x3, boot card: 0x0, io_card 2
- [ 1.965692] [mmc]: sdc0 set ios: clk 0Hz bm OD pm OFF vdd 3.3V width 1 timing LEGACY(SDR12) dt B
- [ 1.978836] [mmc]: sdc1 set ios: clk 0Hz bm OD pm OFF vdd 3.3V width 1 timing LEGACY(SDR12) dt B
- [ 1.991368] no blue_led, ignore it!
- [ 1.995430] Registered led device: red_led
- [ 2.000085] Registered led device: green_led
- [ 2.005509] usbcore: registered new interface driver usbhid
- [ 2.011709] usbhid: USB HID core driver
- [ 2.019505] asoc: sndcodec <-> sunxi-codec mapping ok
- [ 2.028168] asoc: sndhdmi <-> sunxi-hdmiaudio.0 mapping ok
- [ 2.035018] oprofile: using arm/armv7-ca7
- [ 2.039624] u32 classifier
- [ 2.042672] Actions configured
- [ 2.046604] IPv4 over IPv4 tunneling driver
- [ 2.051804] TCP: bic registered
- [ 2.055288] TCP: cubic registered
- [ 2.058958] TCP: westwood registered
- [ 2.062936] TCP: highspeed registered
- [ 2.066993] TCP: hybla registered
- [ 2.070685] TCP: htcp registered
- [ 2.074260] TCP: vegas registered
- [ 2.077930] TCP: veno registered
- [ 2.081515] TCP: scalable registered
- [ 2.085475] TCP: lp registered
- [ 2.088856] TCP: yeah registered
- [ 2.092441] TCP: illinois registered
- [ 2.096401] Initializing XFRM netlink socket
- [ 2.101336] NET: Registered protocol family 10
- [ 2.107288] NET: Registered protocol family 17
- [ 2.112266] NET: Registered protocol family 15
- [ 2.117224] Registering the dns_resolver key type
- [ 2.122877] VFP support v0.3: implementor 41 architecture 2 part 30 variant 7 rev 5
- [ 2.131396] ThumbEE CPU extension supported.
- [ 2.136140] Registering SWP/SWPB emulation handler
- [ 2.142332] cmdline,disp=
- [ 2.145534] [HDMI] power vcc-hdmi-18
- [ 2.180252] ths_fetch_sysconfig_para: type err device_used = 1.
- [ 2.187910] parse cooler0 from sysconfig failed
- [ 2.193312] CPU Budget:Register notifier
- [ 2.197662] CPU Budget:register Success
- [ 2.201935] sunxi-budget-cooling sunxi-budget-cooling: Cooling device registered: thermal-budget-0
- [ 2.214693] [rf_pm]: select module num is 7
- [ 2.219337] [rf_pm]: module power0 name vcc-wifi-33
- [ 2.224782] [rf_pm]: failed to fetch module_power1
- [ 2.230105] [rf_pm]: mod has no chip_en gpio
- [ 2.234837] [rf_pm]: failed to fetch lpo_use_apclk
- [ 2.240172] [rf_pm]: regulator on.
- [ 2.243943] [wifi_pm]: no wifi used in configuration
- [ 2.249446] [rfkill]: init no bt used in configuration
- [ 2.255152] ALSA device list:
- [ 2.258437] #0: audiocodec
- [ 2.261637] #1: sndhdmi
- [ 2.264906] Waiting for root device /dev/mmcblk0p1...
- [ 2.790063] [DISP] disp_device_attached_and_enable,line:159:attched ok, mgr0<-->device0, type=4, mode=4
- [ 2.965042] [mmc]: mmc 0 detect change, present 1
- [ 3.470094] [mmc]: sdc0 set ios: clk 0Hz bm PP pm UP vdd 3.3V width 1 timing LEGACY(SDR12) dt B
- [ 3.481376] [mmc]: sdc0 power_supply is null
- [ 3.500072] [mmc]: sdc0 set ios: clk 400000Hz bm PP pm ON vdd 3.3V width 1 timing LEGACY(SDR12) dt B
- [ 3.532393] [mmc]: *** sunxi_mci_dump_errinfo(L826): smc 0 err, cmd 52, RTO !!
- [ 3.541456] [mmc]: *** sunxi_mci_dump_errinfo(L826): smc 0 err, cmd 52, RTO !!
- [ 3.549680] [mmc]: sdc0 set ios: clk 400000Hz bm PP pm ON vdd 3.3V width 1 timing LEGACY(SDR12) dt B
- [ 3.562503] [mmc]: sdc0 set ios: clk 400000Hz bm PP pm ON vdd 3.3V width 1 timing LEGACY(SDR12) dt B
- [ 3.579252] *******************Try sdio*******************
- [ 3.586172] [mmc]: *** sunxi_mci_dump_errinfo(L826): smc 0 err, cmd 5, RTO !!
- [ 3.595047] [mmc]: *** sunxi_mci_dump_errinfo(L826): smc 0 err, cmd 5, RTO !!
- [ 3.603927] [mmc]: *** sunxi_mci_dump_errinfo(L826): smc 0 err, cmd 5, RTO !!
- [ 3.612777] [mmc]: *** sunxi_mci_dump_errinfo(L826): smc 0 err, cmd 5, RTO !!
- [ 3.620829] *******************Try sd *******************
- [ 3.627471] [mmc]: sdc0 set ios: clk 400000Hz bm PP pm ON vdd 3.3V width 1 timing LEGACY(SDR12) dt B
- [ 3.637735] [mmc]: sdc0 set ios: clk 400000Hz bm PP pm ON vdd 3.3V width 1 timing LEGACY(SDR12) dt B
- [ 3.650382] [mmc]: sdc0 set ios: clk 400000Hz bm PP pm ON vdd 3.3V width 1 timing LEGACY(SDR12) dt B
- [ 3.721577] [mmc]: sdc0 set ios: clk 25000000Hz bm PP pm ON vdd 3.3V width 1 timing LEGACY(SDR12) dt B
- [ 3.738221] [mmc]: sdc0 set ios: clk 25000000Hz bm PP pm ON vdd 3.3V width 1 timing SD-HS(SDR25) dt B
- [ 3.748551] [mmc]: sdc0 set ios: clk 50000000Hz bm PP pm ON vdd 3.3V width 1 timing SD-HS(SDR25) dt B
- [ 3.758933] [mmc]: sdc0 set ios: clk 50000000Hz bm PP pm ON vdd 3.3V width 4 timing SD-HS(SDR25) dt B
- [ 3.769274] mmc0: new high speed SDHC card at address aaaa
- [ 3.775884] mmcblk0: mmc0:aaaa SL32G 29.7 GiB
- [ 3.782504] mmcblk0: p1
- [ 3.785892] *******************sd init ok*******************
- [ 3.830253] EXT4-fs (mmcblk0p1): recovery complete
- [ 3.835585] EXT4-fs (mmcblk0p1): mounted filesystem with writeback data mode. Opts: (null)
- [ 3.844828] VFS: Mounted root (ext4 filesystem) on device 179:1.
- [ 3.854026] devtmpfs: mounted
- [ 3.857629] Freeing init memory: 304K
- [ 4.560439] systemd[1]: systemd 215 running in system mode. (+PAM +AUDIT +SELINUX +IMA +SYSVINIT +LIBCRYPTSETUP +GCRYPT +ACL +XZ -SECCOMP -APPARMOR)
- [ 4.575790] systemd[1]: Detected architecture 'arm'.
- Welcome to [1mDebian GNU/Linux 8 (jessie)[0m!
- [ 4.632195] systemd[1]: Set hostname to <orangepione>.
- [ 4.922311] systemd[1]: Cannot add dependency job for unit display-manager.service, ignoring: Unit display-manager.service failed to load: No such file or directory.
- [ 4.941134] systemd[1]: Expecting device dev-ttyS0.device...
- Expecting device dev-ttyS0.device...
- [ 4.970157] systemd[1]: Starting Forward Password Requests to Wall Directory Watch.
- [ 4.978870] systemd[1]: Started Forward Password Requests to Wall Directory Watch.
- [ 4.987373] systemd[1]: Starting Remote File Systems (Pre).
- [[32m OK [0m] Reached target Remote File Systems (Pre).
- [ 5.010116] systemd[1]: Reached target Remote File Systems (Pre).
- [ 5.016997] systemd[1]: Starting Dispatch Password Requests to Console Directory Watch.
- [ 5.026082] systemd[1]: Started Dispatch Password Requests to Console Directory Watch.
- [ 5.034964] systemd[1]: Starting Paths.
- [[32m OK [0m] Reached target Paths.
- [ 5.060102] systemd[1]: Reached target Paths.
- [ 5.065048] systemd[1]: Set up automount Arbitrary Executable File Formats File System Automount Point.
- [ 5.080589] systemd[1]: Starting Encrypted Volumes.
- [[32m OK [0m] Reached target Encrypted Volumes.
- [ 5.110099] systemd[1]: Reached target Encrypted Volumes.
- [ 5.116133] systemd[1]: Starting Swap.
- [[32m OK [0m] Reached target Swap.
- [ 5.140091] systemd[1]: Reached target Swap.
- [ 5.144878] systemd[1]: Starting Root Slice.
- [[32m OK [0m] Created slice Root Slice.
- [ 5.170099] systemd[1]: Created slice Root Slice.
- [ 5.175360] systemd[1]: Starting User and Session Slice.
- [[32m OK [0m] Created slice User and Session Slice.
- [ 5.200105] systemd[1]: Created slice User and Session Slice.
- [ 5.206533] systemd[1]: Starting Delayed Shutdown Socket.
- [[32m OK [0m] Listening on Delayed Shutdown Socket.
- [ 5.230133] systemd[1]: Listening on Delayed Shutdown Socket.
- [ 5.236570] systemd[1]: Starting /dev/initctl Compatibility Named Pipe.
- [[32m OK [0m] Listening on /dev/initctl Compatibility Named Pipe.
- [ 5.260110] systemd[1]: Listening on /dev/initctl Compatibility Named Pipe.
- [ 5.267901] systemd[1]: Starting Journal Socket (/dev/log).
- [[32m OK [0m] Listening on Journal Socket (/dev/log).
- [ 5.290174] systemd[1]: Listening on Journal Socket (/dev/log).
- [ 5.296924] systemd[1]: Starting udev Control Socket.
- [[32m OK [0m] Listening on udev Control Socket.
- [ 5.320172] systemd[1]: Listening on udev Control Socket.
- [ 5.326332] systemd[1]: Starting udev Kernel Socket.
- [[32m OK [0m] Listening on udev Kernel Socket.
- [ 5.350168] systemd[1]: Listening on udev Kernel Socket.
- [ 5.356227] systemd[1]: Starting Journal Socket.
- [[32m OK [0m] Listening on Journal Socket.
- [ 5.385230] systemd[1]: Listening on Journal Socket.
- [ 5.390997] systemd[1]: Starting System Slice.
- [[32m OK [0m] Created slice System Slice.
- [ 5.410180] systemd[1]: Created slice System Slice.
- [ 5.415744] systemd[1]: Starting system-getty.slice.
- [[32m OK [0m] Created slice system-getty.slice.
- [ 5.440183] systemd[1]: Created slice system-getty.slice.
- [ 5.446325] systemd[1]: Starting system-serial\x2dgetty.slice.
- [[32m OK [0m] Created slice system-serial\x2dgetty.slice.
- [ 5.470170] systemd[1]: Created slice system-serial\x2dgetty.slice.
- [ 5.477369] systemd[1]: Starting Increase datagram queue length...
- Starting Increase datagram queue length...
- [ 5.600798] systemd[1]: Starting Restore / save the current clock...
- Starting Restore / save the current clock...
- [ 5.742357] systemd[1]: Started Set Up Additional Binary Formats.
- [ 5.749615] systemd[1]: Starting Create list of required static device nodes for the current kernel...
- Starting Create list of required static device nodes...rrent kernel...
- [ 5.841427] systemd[1]: Starting Load Kernel Modules...
- Starting Load Kernel Modules...
- [ 5.940911] systemd[1]: Mounted Huge Pages File System.
- [ 5.947435] systemd[1]: Mounting Debug File System...
- Mounting Debug File System...
- [ 5.973991] failed to get normal led pin assign
- [ 5.979080] failed to get standby led pin assign
- [ 5.984490] gpio_pin_1(12) gpio_request
- [ 5.989026] gpio_pin_2(11) gpio_request
- [ 5.993535] gpio_pin_3(6) gpio_request
- [ 5.997915] gpio_pin_4(13) gpio_request
- [ 6.002406] gpio_pin_5(14) gpio_request
- [ 6.006852] gpio_pin_6(1) gpio_request
- [ 6.011234] gpio_pin_7(110) gpio_request
- [ 6.015802] gpio_pin_8(0) gpio_request
- [ 6.020199] gpio_pin_9(3) gpio_request
- [ 6.020591] systemd[1]: Starting udev Coldplug all Devices...
- [ 6.031109] gpio_pin_10(68) gpio_request
- [ 6.035692] gpio_pin_11(71) gpio_request
- Starting udev Coldplug all Devic[ 6.041034] gpio_pin_12(64) gpio_request
- es...
- [ 6.047957] gpio_pin_13(65) gpio_request
- [ 6.052895] gpio_pin_14(2) gpio_request
- [ 6.057249] gpio_pin_15(66) gpio_request
- [ 6.061750] gpio_pin_16(67) gpio_request
- [ 6.066292] gpio_pin_17(21) gpio_request
- [ 6.070784] gpio_pin_18(19) gpio_request
- [ 6.075241] gpio_pin_19(18) gpio_request
- [ 6.079711] gpio_pin_20(7) gpio_request
- [ 6.084103] gpio_pin_21(8) gpio_request
- [ 6.088477] gpio_pin_22(200) gpio_request
- [ 6.093080] gpio_pin_23(9) gpio_request
- [ 6.097418] gpio_pin_24(10) gpio_request
- [ 6.101868] gpio_pin_25(201) gpio_request
- [ 6.106392] gpio_pin_26(20) gpio_request
- [ 6.110846] gpio_pin_27(198) gpio_request
- [ 6.115374] gpio_pin_28(199) gpio_request
- [ 6.119959] get config err!
- [ 6.120617] systemd[1]: Mounted POSIX Message Queue File System.
- [ 6.120724] systemd[1]: Starting LSB: Set keymap...
- [ 6.135201] gpio_sw: probe of gpio_sw.0 failed with error -12
- [ 6.141670] get config err!
- Starting LSB: Set keymap...
- [ 6.145553] gpio_sw: probe of gpio_sw.1 failed with error -12
- [ 6.154507] gpio name is PA12, ret = 0
- [ 6.158836] gpio name is PA11, ret = 0
- [ 6.163138] gpio name is PA6, ret = 0
- [ 6.167310] gpio name is PA13, ret = 0
- [ 6.171615] gpio name is PA14, ret = 0
- [ 6.175975] gpio name is PA1, ret = 0
- [ 6.180189] gpio name is PD14, ret = 0
- [ 6.184477] gpio name is PA0, ret = 0
- [ 6.188651] gpio name is PA3, ret = 0
- [ 6.192847] gpio name is PC4, ret = 0
- [ 6.197026] gpio name is PC7, ret = 0
- [ 6.201226] gpio name is PC0, ret = 0
- [ 6.205401] gpio name is PC1, ret = 0
- [ 6.209570] gpio name is PA2, ret = 0
- [ 6.210387] systemd[1]: Starting Slices.
- [[32m OK [0m[ 6.218244] gpio name is PC2, ret = 0
- ] Reached target Slices.
- [ 6.223836] gpio name is PC3, ret = 0
- [ 6.230096] gpio name is PA21, ret = 0
- [ 6.234364] gpio name is PA19, ret = 0
- [ 6.238635] gpio name is PA18, ret = 0
- [ 6.242929] gpio name is PA7, ret = 0
- [ 6.247104] gpio name is PA8, ret = 0
- [ 6.251292] systemd[1]: Reached target Slices.
- [ 6.251308] gpio name is PG8, ret = 0
- [ 6.251441] gpio name is PA9, ret = 0
- [ 6.251570] gpio name is PA10, ret = 0
- [ 6.251689] gpio name is PG9, ret = 0
- [ 6.251814] gpio name is PA20, ret = 0
- [ 6.251979] gpio_init finish with uesd 1!
- [[32m OK [0m[ 6.288414] W1_SUNXI: Added w1-gpio on GPIO-20
- ] Mounted Debug File System.
- [ 6.298006] Driver for 1-wire Dallas network protocol.
- [ 6.310192] systemd[1]: Mounted Debug File System.
- [[32m OK [0m] Started Increase datagram queue length.
- [ 6.420125] systemd[1]: Started Increase datagram queue length.
- [[32m OK [0m] Started Restore / save the current clock.
- [ 6.510153] systemd[1]: Started Restore / save the current clock.
- [[32m OK [0m] Started Create list of required static device nodes ...current kernel.
- [ 6.590139] systemd[1]: Started Create list of required static device nodes for the current kernel.
- [[32m OK [0m] Started Load Kernel Modules.
- [ 6.770194] systemd[1]: Started Load Kernel Modules.
- [[32m OK [0m] Started LSB: Set keymap.
- [ 6.840158] systemd[1]: Started LSB: Set keymap.
- [[32m OK [0m] Started udev Coldplug all Devices.
- [ 6.970144] systemd[1]: Started udev Coldplug all Devices.
- [ 6.978879] systemd[1]: Time has been changed
- [ 6.984246] systemd[1]: Starting Apply Kernel Variables...
- Starting Apply Kernel Variables...
- [ 7.120930] systemd[1]: Mounting FUSE Control File System...
- Mounting FUSE Control File System...
- [ 7.210953] systemd[1]: Mounted Configuration File System.
- [ 7.217711] systemd[1]: Starting Create Static Device Nodes in /dev...
- Starting Create Static Device Nodes in /dev...
- [ 7.330844] systemd[1]: Starting Syslog Socket.
- [[32m OK [0m] Listening on Syslog Socket.
- [ 7.350310] systemd[1]: Listening on Syslog Socket.
- [ 7.355998] systemd[1]: Starting Journal Service...
- Starting Journal Service...
- [[32m OK [0m] Started Journal Service.
- [ 7.470303] systemd[1]: Started Journal Service.
- [[32m OK [0m] Mounted FUSE Control File System.
- [[32m OK [0m] Started Apply Kernel Variables.
- [[32m OK [0m] Started Create Static Device Nodes in /dev.
- Starting udev Kernel Device Manager...
- [ 7.806882] systemd-udevd[107]: starting version 215
- [[32m OK [0m] Started udev Kernel Device Manager.
- Starting Copy rules generated while the root was ro...
- Starting LSB: Set preliminary keymap...
- Starting LSB: Tune IDE hard disks...
- [ 8.065072] Unable to handle kernel paging request at virtual address 005f001f
Advertisement
Add Comment
Please, Sign In to add comment
Advertisement