Not a member of Pastebin yet?
Sign Up,
it unlocks many cool features!
- truenas_admin@truenas[~]$ sudo smartctl -a /dev/sda
- smartctl 7.4 2023-08-01 r5530 [x86_64-linux-6.18.52-production+truenas] (local build)
- Copyright (C) 2002-23, Bruce Allen, Christian Franke, www.smartmontools.org
- === START OF INFORMATION SECTION ===
- Model Family: Western Digital Red
- Device Model: WDC WD120EMFZ-11A6JA0
- Serial Number: 9JK3YL1T
- LU WWN Device Id: 5 000cca 258ec12ac
- Firmware Version: 81.00A81
- User Capacity: 12,000,138,625,024 bytes [12.0 TB]
- Sector Sizes: 512 bytes logical, 4096 bytes physical
- Rotation Rate: 5400 rpm
- Form Factor: 3.5 inches
- Device is: In smartctl database 7.3/5528
- ATA Version is: ACS-2, ATA8-ACS T13/1699-D revision 4
- SATA Version is: SATA 3.2, 6.0 Gb/s (current: 6.0 Gb/s)
- Local Time is: Fri Nov 6 20:33:41 2026 PST
- SMART support is: Available - device has SMART capability.
- SMART support is: Enabled
- === START OF READ SMART DATA SECTION ===
- SMART overall-health self-assessment test result: PASSED
- General SMART Values:
- Offline data collection status: (0x82) Offline data collection activity
- was completed without error.
- Auto Offline Data Collection: Enabled.
- Self-test execution status: ( 0) The previous self-test routine completed
- without error or no self-test has ever
- been run.
- Total time to complete Offline
- data collection: ( 101) seconds.
- Offline data collection
- capabilities: (0x5b) SMART execute Offline immediate.
- Auto Offline data collection on/off support.
- Suspend Offline collection upon new
- command.
- Offline surface scan supported.
- Self-test supported.
- No Conveyance Self-test supported.
- Selective Self-test supported.
- SMART capabilities: (0x0003) Saves SMART data before entering
- power-saving mode.
- Supports SMART auto save timer.
- Error logging capability: (0x01) Error logging supported.
- General Purpose Logging supported.
- Short self-test routine
- recommended polling time: ( 2) minutes.
- Extended self-test routine
- recommended polling time: (1231) minutes.
- SCT capabilities: (0x003d) SCT Status supported.
- SCT Error Recovery Control supported.
- SCT Feature Control supported.
- SCT Data Table supported.
- SMART Attributes Data Structure revision number: 16
- Vendor Specific SMART Attributes with Thresholds:
- ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
- 1 Raw_Read_Error_Rate 0x000b 100 100 001 Pre-fail Always - 0
- 2 Throughput_Performance 0x0004 135 135 054 Old_age Offline - 112
- 3 Spin_Up_Time 0x0007 083 083 001 Pre-fail Always - 344 (Average 345)
- 4 Start_Stop_Count 0x0012 089 089 000 Old_age Always - 4484
- 5 Reallocated_Sector_Ct 0x0033 100 100 001 Pre-fail Always - 0
- 7 Seek_Error_Rate 0x000a 100 100 001 Old_age Always - 0
- 8 Seek_Time_Performance 0x0004 133 133 020 Old_age Offline - 18
- 9 Power_On_Hours 0x0012 092 092 000 Old_age Always - 56975
- 10 Spin_Retry_Count 0x0012 100 100 001 Old_age Always - 0
- 12 Power_Cycle_Count 0x0032 097 097 000 Old_age Always - 228
- 22 Helium_Level 0x0023 100 100 025 Pre-fail Always - 100
- 192 Power-Off_Retract_Count 0x0032 091 091 000 Old_age Always - 58686
- 193 Load_Cycle_Count 0x0012 091 091 000 Old_age Always - 58686
- 194 Temperature_Celsius 0x0002 025 025 000 Old_age Always - 49 (Min/Max 0/58)
- 196 Reallocated_Event_Count 0x0032 100 100 000 Old_age Always - 0
- 197 Current_Pending_Sector 0x0022 100 100 000 Old_age Always - 0
- 198 Offline_Uncorrectable 0x0008 100 100 000 Old_age Offline - 0
- 199 UDMA_CRC_Error_Count 0x000a 100 100 000 Old_age Always - 0
- SMART Error Log Version: 1
- No Errors Logged
- SMART Self-test log structure revision number 1
- Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error
- # 1 Extended offline Completed without error 00% 56973 -
- # 2 Short offline Completed without error 00% 38961 -
- # 3 Short offline Completed without error 00% 38793 -
- # 4 Short offline Completed without error 00% 38625 -
- # 5 Short offline Completed without error 00% 38458 -
- # 6 Short offline Completed without error 00% 38290 -
- # 7 Short offline Completed without error 00% 38122 -
- # 8 Short offline Completed without error 00% 37954 -
- # 9 Short offline Completed without error 00% 37786 -
- #10 Short offline Completed without error 00% 37618 -
- #11 Short offline Completed without error 00% 37450 -
- #12 Short offline Completed without error 00% 37282 -
- #13 Short offline Completed without error 00% 37114 -
- #14 Short offline Completed without error 00% 36946 -
- #15 Short offline Completed without error 00% 36778 -
- #16 Short offline Completed without error 00% 36610 -
- #17 Short offline Completed without error 00% 36442 -
- #18 Short offline Completed without error 00% 36274 -
- #19 Short offline Completed without error 00% 36108 -
- #20 Short offline Completed without error 00% 35940 -
- #21 Short offline Completed without error 00% 35774 -
- SMART Selective self-test log data structure revision number 1
- SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
- 1 0 0 Not_testing
- 2 0 0 Not_testing
- 3 0 0 Not_testing
- 4 0 0 Not_testing
- 5 0 0 Not_testing
- Selective self-test flags (0x0):
- After scanning selected spans, do NOT read-scan remainder of disk.
- If Selective self-test is pending on power-up, resume after 0 minute delay.
- The above only provides legacy SMART information - try 'smartctl -x' for more
- =========================================================================================================================================================================
- =========================================================================================================================================================================
- =========================================================================================================================================================================
- truenas_admin@truenas[~]$ sudo smartctl -a /dev/sdc
- smartctl 7.4 2023-08-01 r5530 [x86_64-linux-6.18.52-production+truenas] (local build)
- Copyright (C) 2002-23, Bruce Allen, Christian Franke, www.smartmontools.org
- === START OF INFORMATION SECTION ===
- Model Family: Western Digital Red
- Device Model: WDC WD120EMFZ-11A6JA0
- Serial Number: 9RGAT4NC
- LU WWN Device Id: 5 000cca 264c4e65e
- Firmware Version: 81.00A81
- User Capacity: 12,000,138,625,024 bytes [12.0 TB]
- Sector Sizes: 512 bytes logical, 4096 bytes physical
- Rotation Rate: 5400 rpm
- Form Factor: 3.5 inches
- Device is: In smartctl database 7.3/5528
- ATA Version is: ACS-2, ATA8-ACS T13/1699-D revision 4
- SATA Version is: SATA 3.2, 6.0 Gb/s (current: 6.0 Gb/s)
- Local Time is: Fri Nov 6 20:34:13 2026 PST
- SMART support is: Available - device has SMART capability.
- SMART support is: Enabled
- === START OF READ SMART DATA SECTION ===
- SMART overall-health self-assessment test result: PASSED
- General SMART Values:
- Offline data collection status: (0x82) Offline data collection activity
- was completed without error.
- Auto Offline Data Collection: Enabled.
- Self-test execution status: ( 0) The previous self-test routine completed
- without error or no self-test has ever
- been run.
- Total time to complete Offline
- data collection: ( 101) seconds.
- Offline data collection
- capabilities: (0x5b) SMART execute Offline immediate.
- Auto Offline data collection on/off support.
- Suspend Offline collection upon new
- command.
- Offline surface scan supported.
- Self-test supported.
- No Conveyance Self-test supported.
- Selective Self-test supported.
- SMART capabilities: (0x0003) Saves SMART data before entering
- power-saving mode.
- Supports SMART auto save timer.
- Error logging capability: (0x01) Error logging supported.
- General Purpose Logging supported.
- Short self-test routine
- recommended polling time: ( 2) minutes.
- Extended self-test routine
- recommended polling time: (1310) minutes.
- SCT capabilities: (0x003d) SCT Status supported.
- SCT Error Recovery Control supported.
- SCT Feature Control supported.
- SCT Data Table supported.
- SMART Attributes Data Structure revision number: 16
- Vendor Specific SMART Attributes with Thresholds:
- ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
- 1 Raw_Read_Error_Rate 0x000b 100 100 001 Pre-fail Always - 0
- 2 Throughput_Performance 0x0004 135 135 054 Old_age Offline - 112
- 3 Spin_Up_Time 0x0007 083 083 001 Pre-fail Always - 350 (Average 342)
- 4 Start_Stop_Count 0x0012 091 091 000 Old_age Always - 3747
- 5 Reallocated_Sector_Ct 0x0033 100 100 001 Pre-fail Always - 0
- 7 Seek_Error_Rate 0x000a 100 100 001 Old_age Always - 0
- 8 Seek_Time_Performance 0x0004 133 133 020 Old_age Offline - 18
- 9 Power_On_Hours 0x0012 093 093 000 Old_age Always - 54464
- 10 Spin_Retry_Count 0x0012 100 100 001 Old_age Always - 0
- 12 Power_Cycle_Count 0x0032 097 097 000 Old_age Always - 212
- 22 Helium_Level 0x0023 100 100 025 Pre-fail Always - 100
- 192 Power-Off_Retract_Count 0x0032 092 092 000 Old_age Always - 58125
- 193 Load_Cycle_Count 0x0012 092 092 000 Old_age Always - 58125
- 194 Temperature_Celsius 0x0002 020 020 000 Old_age Always - 52 (Min/Max 0/56)
- 196 Reallocated_Event_Count 0x0032 100 100 000 Old_age Always - 0
- 197 Current_Pending_Sector 0x0022 100 100 000 Old_age Always - 0
- 198 Offline_Uncorrectable 0x0008 100 100 000 Old_age Offline - 0
- 199 UDMA_CRC_Error_Count 0x000a 100 100 000 Old_age Always - 6
- SMART Error Log Version: 1
- ATA Error Count: 6 (device log contains only the most recent five errors)
- CR = Command Register [HEX]
- FR = Features Register [HEX]
- SC = Sector Count Register [HEX]
- SN = Sector Number Register [HEX]
- CL = Cylinder Low Register [HEX]
- CH = Cylinder High Register [HEX]
- DH = Device/Head Register [HEX]
- DC = Device Command Register [HEX]
- ER = Error register [HEX]
- ST = Status register [HEX]
- Powered_Up_Time is measured from power on, and printed as
- DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
- SS=sec, and sss=millisec. It "wraps" after 49.710 days.
- Error 6 occurred at disk power-on lifetime: 27011 hours (1125 days + 11 hours)
- When the command that caused the error occurred, the device was active or idle.
- After command completion occurred, registers were:
- ER ST SC SN CL CH DH
- -- -- -- -- -- -- --
- 84 41 00 00 00 00 00 Error: ICRC, ABRT at LBA = 0x00000000 = 0
- Commands leading to the command that caused the error were:
- CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
- -- -- -- -- -- -- -- -- ---------------- --------------------
- 60 58 00 28 0d 91 40 00 19d+22:13:13.278 READ FPDMA QUEUED
- 60 b0 08 80 12 91 40 00 19d+22:13:13.276 READ FPDMA QUEUED
- 60 58 10 d0 07 91 40 00 19d+22:13:13.269 READ FPDMA QUEUED
- 60 58 08 78 02 91 40 00 19d+22:13:13.268 READ FPDMA QUEUED
- 60 a8 00 d0 ff 90 40 00 19d+22:13:13.268 READ FPDMA QUEUED
- Error 5 occurred at disk power-on lifetime: 27011 hours (1125 days + 11 hours)
- When the command that caused the error occurred, the device was active or idle.
- After command completion occurred, registers were:
- ER ST SC SN CL CH DH
- -- -- -- -- -- -- --
- 84 41 00 00 00 00 00 Error: ICRC, ABRT at LBA = 0x00000000 = 0
- Commands leading to the command that caused the error were:
- CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
- -- -- -- -- -- -- -- -- ---------------- --------------------
- 60 b0 00 70 e3 5f 40 00 19d+22:08:50.077 READ FPDMA QUEUED
- 60 a8 00 c8 e0 5f 40 00 19d+22:08:50.073 READ FPDMA QUEUED
- 60 b0 00 18 de 5f 40 00 19d+22:08:50.073 READ FPDMA QUEUED
- 60 a8 00 70 db 5f 40 00 19d+22:08:50.071 READ FPDMA QUEUED
- 60 b0 00 c0 d8 5f 40 00 19d+22:08:50.070 READ FPDMA QUEUED
- Error 4 occurred at disk power-on lifetime: 27011 hours (1125 days + 11 hours)
- When the command that caused the error occurred, the device was active or idle.
- After command completion occurred, registers were:
- ER ST SC SN CL CH DH
- -- -- -- -- -- -- --
- 84 41 00 00 00 00 00 Error: ICRC, ABRT at LBA = 0x00000000 = 0
- Commands leading to the command that caused the error were:
- CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
- -- -- -- -- -- -- -- -- ---------------- --------------------
- 60 58 00 30 1e e5 40 00 19d+22:08:23.181 READ FPDMA QUEUED
- 60 58 08 88 23 e5 40 00 19d+22:08:23.180 READ FPDMA QUEUED
- 60 58 08 d8 18 e5 40 00 19d+22:08:23.174 READ FPDMA QUEUED
- 60 58 00 80 13 e5 40 00 19d+22:08:23.174 READ FPDMA QUEUED
- 60 58 08 28 0e e5 40 00 19d+22:08:23.168 READ FPDMA QUEUED
- Error 3 occurred at disk power-on lifetime: 27011 hours (1125 days + 11 hours)
- When the command that caused the error occurred, the device was active or idle.
- After command completion occurred, registers were:
- ER ST SC SN CL CH DH
- -- -- -- -- -- -- --
- 84 41 00 00 00 00 00 Error: ICRC, ABRT at LBA = 0x00000000 = 0
- Commands leading to the command that caused the error were:
- CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
- -- -- -- -- -- -- -- -- ---------------- --------------------
- 60 a8 00 88 3f b5 40 00 19d+21:57:24.730 READ FPDMA QUEUED
- 60 b0 00 d8 3c b5 40 00 19d+21:57:24.724 READ FPDMA QUEUED
- 60 a8 00 30 3a b5 40 00 19d+21:57:24.723 READ FPDMA QUEUED
- 60 b0 00 80 37 b5 40 00 19d+21:57:24.722 READ FPDMA QUEUED
- 60 a8 00 d8 34 b5 40 00 19d+21:57:24.713 READ FPDMA QUEUED
- Error 2 occurred at disk power-on lifetime: 27010 hours (1125 days + 10 hours)
- When the command that caused the error occurred, the device was active or idle.
- After command completion occurred, registers were:
- ER ST SC SN CL CH DH
- -- -- -- -- -- -- --
- 84 41 00 00 00 00 00 Error: ICRC, ABRT at LBA = 0x00000000 = 0
- Commands leading to the command that caused the error were:
- CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
- -- -- -- -- -- -- -- -- ---------------- --------------------
- 60 58 08 30 d0 21 40 00 19d+21:19:37.201 READ FPDMA QUEUED
- 60 58 00 d8 ca 21 40 00 19d+21:19:37.186 READ FPDMA QUEUED
- 60 58 10 80 c5 21 40 00 19d+21:19:37.176 READ FPDMA QUEUED
- 60 58 08 28 c0 21 40 00 19d+21:19:37.176 READ FPDMA QUEUED
- 60 58 00 d0 ba 21 40 00 19d+21:19:37.176 READ FPDMA QUEUED
- SMART Self-test log structure revision number 1
- Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error
- # 1 Extended offline Completed without error 00% 54462 -
- # 2 Short offline Completed without error 00% 36444 -
- # 3 Short offline Completed without error 00% 36276 -
- # 4 Short offline Completed without error 00% 36108 -
- # 5 Short offline Completed without error 00% 35941 -
- # 6 Short offline Completed without error 00% 35773 -
- # 7 Short offline Completed without error 00% 35605 -
- # 8 Short offline Completed without error 00% 35437 -
- # 9 Short offline Completed without error 00% 35269 -
- #10 Short offline Completed without error 00% 35101 -
- #11 Short offline Completed without error 00% 34933 -
- #12 Short offline Completed without error 00% 34765 -
- #13 Short offline Completed without error 00% 34597 -
- #14 Short offline Completed without error 00% 34429 -
- #15 Short offline Completed without error 00% 34261 -
- #16 Short offline Completed without error 00% 34093 -
- #17 Short offline Completed without error 00% 33925 -
- #18 Short offline Completed without error 00% 33757 -
- #19 Short offline Completed without error 00% 33591 -
- #20 Short offline Completed without error 00% 33423 -
- #21 Short offline Completed without error 00% 33257 -
- SMART Selective self-test log data structure revision number 1
- SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
- 1 0 0 Not_testing
- 2 0 0 Not_testing
- 3 0 0 Not_testing
- 4 0 0 Not_testing
- 5 0 0 Not_testing
- Selective self-test flags (0x0):
- After scanning selected spans, do NOT read-scan remainder of disk.
- If Selective self-test is pending on power-up, resume after 0 minute delay.
- The above only provides legacy SMART information - try 'smartctl -x' for more
- =========================================================================================================================================================================
- =========================================================================================================================================================================
- =========================================================================================================================================================================
- truenas_admin@truenas[~]$ sudo smartctl -a /dev/sdd
- smartctl 7.4 2023-08-01 r5530 [x86_64-linux-6.18.52-production+truenas] (local build)
- Copyright (C) 2002-23, Bruce Allen, Christian Franke, www.smartmontools.org
- === START OF INFORMATION SECTION ===
- Model Family: Western Digital Red
- Device Model: WDC WD120EMFZ-11A6JA0
- Serial Number: Z2GR33MT
- LU WWN Device Id: 5 000cca 28dca0bdd
- Firmware Version: 81.00A81
- User Capacity: 12,000,138,625,024 bytes [12.0 TB]
- Sector Sizes: 512 bytes logical, 4096 bytes physical
- Rotation Rate: 5400 rpm
- Form Factor: 3.5 inches
- Device is: In smartctl database 7.3/5528
- ATA Version is: ACS-2, ATA8-ACS T13/1699-D revision 4
- SATA Version is: SATA 3.2, 6.0 Gb/s (current: 6.0 Gb/s)
- Local Time is: Fri Nov 6 20:34:35 2026 PST
- SMART support is: Available - device has SMART capability.
- SMART support is: Enabled
- === START OF READ SMART DATA SECTION ===
- SMART overall-health self-assessment test result: PASSED
- General SMART Values:
- Offline data collection status: (0x82) Offline data collection activity
- was completed without error.
- Auto Offline Data Collection: Enabled.
- Self-test execution status: ( 0) The previous self-test routine completed
- without error or no self-test has ever
- been run.
- Total time to complete Offline
- data collection: ( 101) seconds.
- Offline data collection
- capabilities: (0x5b) SMART execute Offline immediate.
- Auto Offline data collection on/off support.
- Suspend Offline collection upon new
- command.
- Offline surface scan supported.
- Self-test supported.
- No Conveyance Self-test supported.
- Selective Self-test supported.
- SMART capabilities: (0x0003) Saves SMART data before entering
- power-saving mode.
- Supports SMART auto save timer.
- Error logging capability: (0x01) Error logging supported.
- General Purpose Logging supported.
- Short self-test routine
- recommended polling time: ( 2) minutes.
- Extended self-test routine
- recommended polling time: (1325) minutes.
- SCT capabilities: (0x003d) SCT Status supported.
- SCT Error Recovery Control supported.
- SCT Feature Control supported.
- SCT Data Table supported.
- SMART Attributes Data Structure revision number: 16
- Vendor Specific SMART Attributes with Thresholds:
- ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
- 1 Raw_Read_Error_Rate 0x000b 100 100 001 Pre-fail Always - 0
- 2 Throughput_Performance 0x0004 135 135 054 Old_age Offline - 112
- 3 Spin_Up_Time 0x0007 083 083 001 Pre-fail Always - 347 (Average 347)
- 4 Start_Stop_Count 0x0012 091 091 000 Old_age Always - 3984
- 5 Reallocated_Sector_Ct 0x0033 100 100 001 Pre-fail Always - 0
- 7 Seek_Error_Rate 0x000a 100 100 001 Old_age Always - 0
- 8 Seek_Time_Performance 0x0004 133 133 020 Old_age Offline - 18
- 9 Power_On_Hours 0x0012 093 093 000 Old_age Always - 54455
- 10 Spin_Retry_Count 0x0012 100 100 001 Old_age Always - 0
- 12 Power_Cycle_Count 0x0032 097 097 000 Old_age Always - 204
- 22 Helium_Level 0x0023 100 100 025 Pre-fail Always - 100
- 192 Power-Off_Retract_Count 0x0032 092 092 000 Old_age Always - 58008
- 193 Load_Cycle_Count 0x0012 092 092 000 Old_age Always - 58008
- 194 Temperature_Celsius 0x0002 028 028 000 Old_age Always - 47 (Min/Max 0/51)
- 196 Reallocated_Event_Count 0x0032 100 100 000 Old_age Always - 0
- 197 Current_Pending_Sector 0x0022 100 100 000 Old_age Always - 0
- 198 Offline_Uncorrectable 0x0008 100 100 000 Old_age Offline - 0
- 199 UDMA_CRC_Error_Count 0x000a 100 100 000 Old_age Always - 0
- SMART Error Log Version: 1
- No Errors Logged
- SMART Self-test log structure revision number 1
- Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error
- # 1 Extended offline Completed without error 00% 54454 -
- # 2 Short offline Completed without error 00% 36441 -
- # 3 Short offline Completed without error 00% 36273 -
- # 4 Short offline Completed without error 00% 36105 -
- # 5 Short offline Completed without error 00% 35938 -
- # 6 Short offline Completed without error 00% 35770 -
- # 7 Short offline Completed without error 00% 35602 -
- # 8 Short offline Completed without error 00% 35434 -
- # 9 Short offline Completed without error 00% 35266 -
- #10 Short offline Completed without error 00% 35098 -
- #11 Short offline Completed without error 00% 34930 -
- #12 Short offline Completed without error 00% 34762 -
- #13 Short offline Completed without error 00% 34594 -
- #14 Short offline Completed without error 00% 34426 -
- #15 Short offline Completed without error 00% 34258 -
- #16 Short offline Completed without error 00% 34090 -
- #17 Short offline Completed without error 00% 33922 -
- #18 Short offline Completed without error 00% 33754 -
- #19 Short offline Completed without error 00% 33588 -
- #20 Short offline Completed without error 00% 33420 -
- #21 Short offline Completed without error 00% 33255 -
- SMART Selective self-test log data structure revision number 1
- SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
- 1 0 0 Not_testing
- 2 0 0 Not_testing
- 3 0 0 Not_testing
- 4 0 0 Not_testing
- 5 0 0 Not_testing
- Selective self-test flags (0x0):
- After scanning selected spans, do NOT read-scan remainder of disk.
- If Selective self-test is pending on power-up, resume after 0 minute delay.
- The above only provides legacy SMART information - try 'smartctl -x' for more
Advertisement
Add Comment
Please, Sign In to add comment