Advertisement
zmleitao

boot_panic_zedboard

Aug 15th, 2013
450
0
Never
Not a member of Pastebin yet? Sign Up, it unlocks many cool features!
text 10.22 KB | None | 0 0
  1.  
  2.  
  3. U-Boot 2012.10-dirty (Aug 15 2013 - 18:34:06)
  4.  
  5. DRAM: 512 MiB
  6. WARNING: Caches not enabled
  7. MMC: SDHCI: 0
  8. SF: Detected S25FL256S with page size 64 KiB, total 32 MiB
  9. SF: Warning - Only lower 16MB is accessible in 3 byte addressing mode
  10. In: serial
  11. Out: serial
  12. Err: serial
  13. Net: zynq_gem
  14. Hit any key to stop autoboot: 0
  15. Copying Linux from SD to RAM...
  16. Device: SDHCI
  17. Manufacturer ID: 3
  18. OEM: 5344
  19. Name: SD16G
  20. Tran Speed: 25000000
  21. Rd Block Len: 512
  22. SD version 2.0
  23. High Capacity: Yes
  24. Capacity: 14.8 GiB
  25. Bus Width: 4-bit
  26. reading uImage
  27.  
  28. 3002302 bytes read
  29. reading devicetree.dtb
  30.  
  31. 9458 bytes read
  32. ## Booting kernel from Legacy Image at 03000000 ...
  33. Image Name: Linux kernel
  34. Image Type: ARM Linux Kernel Image (gzip compressed)
  35. Data Size: 3002238 Bytes = 2.9 MiB
  36. Load Address: 00008000
  37. Entry Point: 00008000
  38. Verifying Checksum ... OK
  39. ## Flattened Device Tree blob at 02a00000
  40. Booting using the fdt blob at 0x02a00000
  41. Uncompressing Kernel Image ... OK
  42. Loading Device Tree to 1fb4f000, end 1fb544f1 ... OK
  43.  
  44. Starting kernel ...
  45.  
  46. Uncompressing Linux... done, booting the kernel.
  47. Booting Linux on physical CPU 0x0
  48. Linux version 3.10.0-g68b7238 (root@liliana) (gcc version 4.6.3 (Sourcery CodeBench Lite 2012.03-79) ) #1 SMP PREEMPT Thu Aug 15 17:51:15 WEST 2013
  49. CPU: ARMv7 Processor [413fc090] revision 0 (ARMv7), cr=18c5387d
  50. CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
  51. Machine: Xilinx Zynq Platform, model: Xilinx Zynq ZED
  52. bootconsole [earlycon0] enabled
  53. cma: CMA: reserved 40 MiB at 1d000000
  54. Memory policy: ECC disabled, Data cache writealloc
  55. PERCPU: Embedded 8 pages/cpu @c0ec3000 s8640 r8192 d15936 u32768
  56. Built 1 zonelists in Zone order, mobility grouping on. Total pages: 130048
  57. Kernel command line: console=ttyPS0,115200 root=/dev/mmcblk0p2 rw earlyprintk rootfstype=ext4 rootwait devtmpfs.mount=0
  58. PID hash table entries: 2048 (order: 1, 8192 bytes)
  59. Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
  60. Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
  61. Memory: 512MB = 512MB total
  62. Memory: 467620k/467620k available, 56668k reserved, 0K highmem
  63. Virtual kernel memory layout:
  64. vector : 0xffff0000 - 0xffff1000 ( 4 kB)
  65. fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB)
  66. vmalloc : 0xe0800000 - 0xff000000 ( 488 MB)
  67. lowmem : 0xc0000000 - 0xe0000000 ( 512 MB)
  68. pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB)
  69. modules : 0xbf000000 - 0xbfe00000 ( 14 MB)
  70. .text : 0xc0008000 - 0xc053d8c8 (5335 kB)
  71. .init : 0xc053e000 - 0xc05681c0 ( 169 kB)
  72. .data : 0xc056a000 - 0xc05a6d00 ( 244 kB)
  73. .bss : 0xc05a6d00 - 0xc0ab7d20 (5189 kB)
  74. Preemptible hierarchical RCU implementation.
  75. RCU lockdep checking is enabled.
  76. Dump stacks of tasks blocking RCU-preempt GP.
  77. RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=2.
  78. NR_IRQS:16 nr_irqs:16 16
  79. slcr mapped to e0802000
  80. Zynq clock init
  81. sched_clock: 16 bits at 54kHz, resolution 18432ns, wraps every 1207ms
  82. timer #0 at e0804000, irq=43
  83. Console: colour dummy device 80x30
  84. Lock dependency validator: Copyright (c) 2006 Red Hat, Inc., Ingo Molnar
  85. ... MAX_LOCKDEP_SUBCLASSES: 8
  86. ... MAX_LOCK_DEPTH: 48
  87. ... MAX_LOCKDEP_KEYS: 8191
  88. ... CLASSHASH_SIZE: 4096
  89. ... MAX_LOCKDEP_ENTRIES: 16384
  90. ... MAX_LOCKDEP_CHAINS: 32768
  91. ... CHAINHASH_SIZE: 16384
  92. memory used by lock dependency info: 3695 kB
  93. per task-struct memory footprint: 1152 bytes
  94. Calibrating delay loop... 1332.01 BogoMIPS (lpj=6660096)
  95. pid_max: default: 32768 minimum: 301
  96. Mount-cache hash table entries: 512
  97. CPU: Testing write buffer coherency: ok
  98. CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
  99. Setting up static identity map for 0xc03a52e8 - 0xc03a531c
  100. L310 cache controller enabled
  101. l2x0: 8 ways, CACHE_ID 0x410000c8, AUX_CTRL 0x72360000, Cache size: 524288 B
  102. CPU1: Booted secondary processor
  103. CPU1: thread -1, cpu 1, socket 0, mpidr 80000001
  104. Brought up 2 CPUs
  105. SMP: Total of 2 processors activated (2664.03 BogoMIPS).
  106. CPU: All CPU(s) started in SVC mode.
  107. devtmpfs: initialized
  108. regulator-dummy: no parameters
  109. NET: Registered protocol family 16
  110. DMA: preallocated 256 KiB pool for atomic coherent allocations
  111. xgpiops e000a000.gpio: gpio at 0xe000a000 mapped to 0xe080e000
  112. hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers.
  113. hw-breakpoint: maximum watchpoint size is 4 bytes.
  114. bio: create slab <bio-0> at 0
  115. SCSI subsystem initialized
  116. usbcore: registered new interface driver usbfs
  117. usbcore: registered new interface driver hub
  118. usbcore: registered new device driver usb
  119. Advanced Linux Sound Architecture Driver Initialized.
  120. Switching to clocksource ttc_clocksource
  121. NET: Registered protocol family 2
  122. TCP established hash table entries: 4096 (order: 3, 32768 bytes)
  123. TCP bind hash table entries: 4096 (order: 5, 147456 bytes)
  124. TCP: Hash tables configured (established 4096 bind 4096)
  125. TCP: reno registered
  126. UDP hash table entries: 256 (order: 2, 20480 bytes)
  127. UDP-Lite hash table entries: 256 (order: 2, 20480 bytes)
  128. NET: Registered protocol family 1
  129. hw perfevents: enabled with ARMv7 Cortex-A9 PMU driver, 7 counters available
  130. msgmni has been set to 993
  131. io scheduler noop registered
  132. io scheduler deadline registered
  133. io scheduler cfq registered (default)
  134. dma-pl330 f8003000.ps7-dma: Loaded driver for PL330 DMAC-2364208
  135. dma-pl330 f8003000.ps7-dma: DBUFF-128x8bytes Num_Chans-8 Num_Peri-4 Num_Events-16
  136. e000console [ttyPS0] enabled, bootconsole disabled
  137. console [ttyPS0] enabled, bootconsole disabled
  138. xdevcfg f8007000.devcfg: ioremap f8007000 to e0816000 with size 100
  139. [drm] Initialized drm 1.1.0 20060810
  140. platform 70e00000.axi_hdmi: Driver axi-hdmi requests probe deferral
  141. brd: module loaded
  142. loop: module loaded
  143. xqspips e000d000.qspi: master is unqueued, this is deprecated
  144. m25p80 spi32766.0: found s25fl256s1, expected m25p80
  145. m25p80 spi32766.0: s25fl256s1 (32768 Kbytes)
  146. 5 ofpart partitions found on MTD device spi32766.0
  147. Creating 5 MTD partitions on "spi32766.0":
  148. 0x000000000000-0x000000500000 : "boot"
  149. 0x000000500000-0x000000520000 : "bootenv"
  150. 0x000000520000-0x000000540000 : "config"
  151. 0x000000540000-0x000000fc0000 : "image"
  152. 0x000000fc0000-0x000002000000 : "spare"
  153. xqspips e000d000.qspi: at 0xE000D000 mapped to 0xE0818000, irq=51
  154. libphy: XEMACPS mii bus: probed
  155. xemacps e000b000.eth: pdev->id -1, baseaddr 0xe000b000, irq 54
  156. ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
  157. ULPI transceiver vendor/product ID 0x0451/0x1507
  158. Found TI TUSB1210 ULPI transceiver.
  159. ULPI integrity check: passed.
  160. xusbps-ehci xusbps-ehci.0: Xilinx PS USB EHCI Host Controller
  161. xusbps-ehci xusbps-ehci.0: new USB bus registered, assigned bus number 1
  162. xusbps-ehci xusbps-ehci.0: irq 53, io mem 0x00000000
  163. xusbps-ehci xusbps-ehci.0: USB 2.0 started, EHCI 1.00
  164. hub 1-0:1.0: USB hub found
  165. hub 1-0:1.0: 1 port detected
  166. usbcore: registered new interface driver usb-storage
  167. mousedev: PS/2 mouse device common for all mice
  168. i2c /dev entries driver
  169. sdhci: Secure Digital Host Controller Interface driver
  170. sdhci: Copyright(c) Pierre Ossman
  171. sdhci-pltfm: SDHCI platform and OF driver helper
  172. mmc0: no vqmmc regulator found
  173. mmc0: no vmmc regulator found
  174. mmc0: Invalid maximum block size, assuming 512 bytes
  175. mmc0: SDHCI controller on e0100000.sdhci [e0100000.sdhci] using ADMA
  176. ledtrig-cpu: registered to indicate activity on CPUs
  177. hidraw: raw HID events driver (C) Jiri Kosina
  178. usbcore: registered new interface driver usbhid
  179. usbhid: USB HID core driver
  180. mmc0: new SDHC card at address e624
  181. mmcblk0: mmc0:e624 SD16G 14.8 GiB
  182. mmcblk0: p1 p2
  183. adv7511-hdmi-snd adv7511_hdmi_snd.4: adv7511 <-> 75c00000.axi-spdif-tx mapping ok
  184. zed-adau1761-snd zed_sound.5: adau-hifi <-> 77600000.axi-i2s mapping ok
  185. TCP: cubic registered
  186. NET: Registered protocol family 17
  187. VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4
  188. Registering SWP/SWPB emulation handler
  189. usb 1-1: new high-speed USB device number 2 using xusbps-ehci
  190. axi-hdmi 70e00000.axi_hdmi: No connectors reported connected with modes
  191. [drm] Cannot find any crtc or sizes - going 1024x768
  192. Console: switching to colour frame buffer device 128x48
  193. axi-hdmi 70e00000.axi_hdmi: fb0: frame buffer device
  194. axi-hdmi 70e00000.axi_hdmi: registered panic notifier
  195. [drm] Initialized axi_hdmi_drm 1.0.0 20120930 on minor 0
  196. drivers/rtc/hctosys.c: unable to open rtc device (rtc0)
  197. hub 1-1:1.0: USB hub found
  198. ALSA device list:
  199. hub 1-1:1.0: 4 ports detected
  200. #0: HDMI monitor
  201. #1: ZED ADAU1761
  202. EXT4-fs (mmcblk0p2): recovery complete
  203. EXT4-fs (mmcblk0p2): mounted filesystem with ordered data mode. Opts: (null)
  204. VFS: Mounted root (ext4 filesystem) on device 179:2.
  205. Freeing unused kernel memory: 168K (c053e000 - c0568000)
  206. request_module: runaway loop modprobe binfmt-0000
  207. request_module: runaway loop modprobe binfmt-0000
  208. Kernel panic - not syncing: No init found. Try passing init= option to kernel. See Linux Documentation/init.txt for guidance.
  209. CPU: 0 PID: 1 Comm: swapper/0 Not tainted 3.10.0-g68b7238 #1
  210. [<c0012b54>] (unwind_backtrace+0x0/0xe0) from [<c0010b70>] (show_stack+0x10/0x14)
  211. [<c0010b70>] (show_stack+0x10/0x14) from [<c039e10c>] (panic+0x88/0x1e0)
  212. [<c039e10c>] (panic+0x88/0x1e0) from [<c03999b4>] (kernel_init+0xb8/0xe4)
  213. [<c03999b4>] (kernel_init+0xb8/0xe4) from [<c000d9c8>] (ret_from_fork+0x14/0x2c)
  214. CPU1: stopping
  215. CPU: 1 PID: 0 Comm: swapper/1 Not tainted 3.10.0-g68b7238 #1
  216. [<c0012b54>] (unwind_backtrace+0x0/0xe0) from [<c0010b70>] (show_stack+0x10/0x14)
  217. [<c0010b70>] (show_stack+0x10/0x14) from [<c0011ab0>] (ipi_cpu_stop+0x3c/0x6c)
  218. [<c0011ab0>] (ipi_cpu_stop+0x3c/0x6c) from [<c0011d48>] (handle_IPI+0x60/0x80)
  219. [<c0011d48>] (handle_IPI+0x60/0x80) from [<c00084fc>] (gic_handle_irq+0x54/0x5c)
  220. [<c00084fc>] (gic_handle_irq+0x54/0x5c) from [<c000d4c4>] (__irq_svc+0x44/0x78)
  221. Exception stack(0xdcc95fa0 to 0xdcc95fe8)
  222. 5fa0: dcc94000 000077ae dcc95fd8 dcc909c0 dcc95ff0 00000015 10c0387d c05a7034
  223. 5fc0: 0000406a 413fc090 00000000 00000000 00000000 dcc95fe8 dcc94018 c000e504
  224. 5fe0: 20000113 ffffffff
  225. [<c000d4c4>] (__irq_svc+0x44/0x78) from [<c000e504>] (arch_cpu_idle+0x28/0x30)
  226. [<c000e504>] (arch_cpu_idle+0x28/0x30) from [<c00514ac>] (cpu_startup_entry+0xb8/0x12c)
  227. [<c00514ac>] (cpu_startup_entry+0xb8/0x12c) from [<0039ab44>] (0x39ab44)
  228. drm_kms_helper: panic occurred, switching back to text console
Advertisement
Add Comment
Please, Sign In to add comment
Advertisement