API tools faq
paste
Guest User

Untitled

a guest
Jul 30th, 2014
340
0
Never
Add comment
Not a member of Pastebin yet? Sign Up, it unlocks many cool features!
text 10.55 KB | None | 0 0
raw download clone embed print report
  1. ####Put here by RP
  2. NML_FILE = emc.nml
  3. ###
  4. # EMC controller parameters for generic controller. Make these what you need
  5. # for your system.
  6.  
  7. # General note: Comments can either be preceded with a # or ; - either is
  8. # acceptable, although # is in keeping with most linux config files.
  9.  
  10. # Settings with a + at the front of the comment are likely needed to get
  11. # changed by the user.
  12. # Settings with a - at the front are highly unneeded to be changed
  13. ###############################################################################
  14. # General section
  15. ###############################################################################
  16. [EMC]
  17.  
  18. #- Version of this INI file
  19. VERSION = $Revision$
  20.  
  21. #+ Name of machine, for use with display, etc.
  22. ######MACHINE = Maho-MC400
  23. MACHINE = LinuxCNC-HAL-STG
  24.  
  25. #+ Debug level, 0 means no messages. See src/emc/nml_int/emcglb.h for others
  26. DEBUG = 0
  27. # DEBUG = 0x00000007
  28. # DEBUG = 0x7FFFFFFF
  29.  
  30. ###############################################################################
  31. # Sections for display options
  32. ###############################################################################
  33. [DISPLAY]
  34.  
  35. #+ Name of display program, e.g., xemc
  36. # DISPLAY = axis
  37. # DISPLAY = usrmot
  38. # DISPLAY = mini
  39. DISPLAY = tkemc
  40. # Cycle time, in seconds, that display will sleep between polls
  41. CYCLE_TIME = 0.200
  42.  
  43. #- Path to help file
  44. HELP_FILE = tklinucnc.txt
  45.  
  46. #- Initial display setting for position, RELATIVE or MACHINE
  47. POSITION_OFFSET = RELATIVE
  48.  
  49. #- Initial display setting for position, COMMANDED or ACTUAL
  50. POSITION_FEEDBACK = ACTUAL
  51.  
  52. #+ Highest value that will be allowed for feed override, 1.0 = 100%
  53. MAX_FEED_OVERRIDE = 1.2
  54.  
  55. #- Prefix to be used
  56. PROGRAM_PREFIX = /home/mc500/linuxcnc/nc_files
  57.  
  58. #- Introductory graphic
  59. INTRO_GRAPHIC = linuxcnc.gif
  60. INTRO_TIME = 5
  61.  
  62.  
  63. ###############################################################################
  64. # Task controller section
  65. ###############################################################################
  66. [TASK]
  67.  
  68. # Name of task controller program, e.g., milltask
  69. TASK = milltask
  70.  
  71. #- Cycle time, in seconds, that task controller will sleep between polls
  72. ###CYCLE_TIME = 0.010
  73. CYCLE_TIME = 0.001
  74.  
  75. ###############################################################################
  76. # Part program interpreter section
  77. ###############################################################################
  78. [RS274NGC]
  79.  
  80. #- File containing interpreter variables
  81. PARAMETER_FILE = stg.var
  82.  
  83. ###############################################################################
  84. # Motion control section
  85. ###############################################################################
  86. [EMCMOT]
  87.  
  88. #- Name of the motion controller to use (only one exists for nontrivkins)
  89. EMCMOT = motmod
  90.  
  91. #- Timeout for comm to emcmot, in seconds
  92. COMM_TIMEOUT = 1.0
  93.  
  94. #- Interval between tries to emcmot, in seconds
  95. COMM_WAIT = 0.010
  96.  
  97. #- Servo task period, in nanosecs - will be rounded to an int multiple of BASE_PERIOD
  98. SERVO_PERIOD = 1000000
  99.  
  100. ###############################################################################
  101. # Hardware Abstraction Layer section
  102. ###############################################################################
  103. [HAL]
  104.  
  105. # The run script first uses halcmd to execute any HALFILE
  106. # files, and then to execute any individual HALCMD commands.
  107. #
  108.  
  109. # list of hal config files to run through halcmd
  110. #+ files are executed in the order in which they appear
  111. HALFILE = core_servo.hal
  112. HALFILE = stg_motion.hal
  113. HALFILE = stg_io.hal
  114.  
  115. #- list of halcmd commands to execute
  116. # commands are executed in the order in which they appear
  117. #HALCMD = save neta
  118.  
  119. ###############################################################################
  120. # Trajectory planner section
  121. ###############################################################################
  122. [TRAJ]
  123. #+ machine specific settings
  124. AXES = 4
  125. ###AXES = 3
  126. # COORDINATES = X Y Z R P W
  127. COORDINATES = X Y Z A
  128. ###COORDINATES = X Y Z
  129. HOME = 0 0 0 0
  130. ###HOME = 0 0 0
  131. LINEAR_UNITS = 0.03937007874016
  132. ###LINEAR_UNITS = mm
  133. ANGULAR_UNITS = 1.0
  134. ###ANGULAR_UNITS = degree
  135. CYCLE_TIME = 1.0
  136. ###CYCLE_TIME = 0.010
  137. DEFAULT_VELOCITY = 4
  138. ###DEFAULT_VELOCITY = 0.424
  139. MAX_VELOCITY = 4
  140. ###MAX_VELOCITY = 30.48
  141. DEFAULT_ACCELERATION = 300.0
  142. MAX_ACCELERATION = 500.0
  143.  
  144. ###############################################################################
  145. # Axes sections
  146. ###############################################################################
  147.  
  148. #+ First axis
  149. # each setting is commented for axis_0
  150. [AXIS_0]
  151.  
  152. # type of axis, LINEAR vs. ROTARY
  153. TYPE = LINEAR
  154. # home position
  155. HOME = 0.000
  156. # maximum velocity
  157. MAX_VELOCITY = 2
  158. ###MAX_VELOCITY = 30.48
  159. # maximum acceleration
  160. MAX_ACCELERATION = 500.0
  161. # machanical backlash measured
  162. BACKLASH = 0.000
  163. # time to update the axis
  164. # number of encoder ticks / unit
  165. INPUT_SCALE = 50800
  166. ###INPUT_SCALE = 200
  167. # dac gain for output
  168. OUTPUT_SCALE = 1.000
  169. # dac bias for output
  170. OUTPUT_OFFSET = 0.000
  171. # minimum travel limit (from position 0)
  172. MIN_LIMIT = -1000.0
  173. # maximum travel limit (from position 0)
  174. MAX_LIMIT = 1000.0
  175. # following error at max speed
  176. FERROR = 1.270
  177. # following error when halted
  178. MIN_FERROR = 0.254
  179. # read HAL_Introduction.pdf for an insight about Homing
  180. HOME_OFFSET = 0.0
  181. HOME_SEARCH_VEL = 0.0
  182. HOME_LATCH_VEL = 0.0
  183. HOME_USE_INDEX = NO
  184. HOME_IGNORE_LIMITS = NO
  185. # PID tuning params
  186. MAX_OUTPUT = 1.0
  187. DEADBAND = 0.000381
  188. P = 2000.000
  189. ###P = 100.0
  190. I = 2000.000
  191. ###I = 0.000
  192. D = 5.000
  193. ###D = 0.000
  194. FF0 = 30.000
  195. ###FF0 = 0.000
  196. FF1 = 3.000
  197. ###FF1 = 0.000
  198. FF2 = 0.0
  199. BIAS = 0.000
  200.  
  201. #+ Second axis
  202. [AXIS_1]
  203.  
  204. TYPE = LINEAR
  205. HOME = 0.000
  206. MAX_VELOCITY = 1.5
  207. ###MAX_VELOCITY = 30.48
  208. MAX_ACCELERATION = 500.0
  209. BACKLASH = 0.000
  210. INPUT_SCALE = 50800
  211. ###INPUT_SCALE = 200
  212. OUTPUT_SCALE = 1.000
  213. OUTPUT_OFFSET = 0.000
  214. MIN_LIMIT = -1000.0
  215. MAX_LIMIT = 1000.0
  216. FERROR = .2
  217. ###FERROR = 1.270
  218. MIN_FERROR = 0.254
  219. HOME_OFFSET = 0.0
  220. HOME_SEARCH_VEL = 0.0
  221. HOME_LATCH_VEL = 0.0
  222. HOME_USE_INDEX = NO
  223. HOME_IGNORE_LIMITS = NO
  224. # PID tuning params
  225. MAX_OUTPUT = 1.0
  226. DEADBAND = 0.000381
  227. P = 1300
  228. ###P = 100.0
  229. I = 900
  230. #I = 0.000
  231. D = 10
  232. ###D = 0.000
  233. FF0 = 0.000
  234. FF1 = 3
  235. ###FF1 = 0.000
  236. FF2 = 0.0
  237. BIAS = 0.000
  238.  
  239. #+ Third axis
  240. [AXIS_2]
  241.  
  242. TYPE = LINEAR
  243. HOME = 0.0
  244. MAX_VELOCITY = 1
  245. ###MAX_VELOCITY = 30.48
  246. MAX_ACCELERATION = 500.0
  247. BACKLASH = 0.000
  248. INPUT_SCALE = 50800
  249. ###INPUT_SCALE = 200
  250. OUTPUT_SCALE = 1.000
  251. OUTPUT_OFFSET = 0.000
  252. MIN_LIMIT = -1000.0
  253. MAX_LIMIT = 1000.0
  254. FERROR = .1
  255. ###FERROR = 1.270
  256. MIN_FERROR = 0.254
  257. HOME_OFFSET = 0.0
  258. HOME_SEARCH_VEL = 0.0
  259. HOME_LATCH_VEL = 0.0
  260. HOME_USE_INDEX = NO
  261. HOME_IGNORE_LIMITS = NO
  262. # PID tuning params
  263. MAX_OUTPUT = 1.0
  264. DEADBAND = 0.000381
  265. P = 150
  266. ###P = 100.0
  267. I = 200
  268. ###I = 0.000
  269. D = .5
  270. ###D = 0.000
  271. FF0 = 0.000
  272. FF1 = .5
  273. ###FF1 = 0.000
  274. FF2 = 0.0
  275. BIAS = 0.000
  276.  
  277. #+ Fourth axis
  278. [AXIS_3]
  279.  
  280. TYPE = LINEAR
  281. HOME = 0.0
  282. MAX_VELOCITY = 5
  283. ###MAX_VELOCITY = 30.48
  284. MAX_ACCELERATION = 500.0
  285. BACKLASH = 0.000
  286. INPUT_SCALE = 1000
  287. ###INPUT_SCALE = 200
  288. OUTPUT_SCALE = 1.000
  289. OUTPUT_OFFSET = 0.000
  290. MIN_LIMIT = -1000.0
  291. MAX_LIMIT = 1000.0
  292. FERROR = 1.270
  293. MIN_FERROR = 0.254
  294. HOME_OFFSET = 0.0
  295. HOME_SEARCH_VEL = 0.0
  296. HOME_LATCH_VEL = 0.0
  297. HOME_USE_INDEX = NO
  298. HOME_IGNORE_LIMITS = NO
  299. # PID tuning params
  300. MAX_OUTPUT = 1.0
  301. DEADBAND = 0.000381
  302. P = 150
  303. ###P = 100.0
  304. I = 200
  305. ###I = 0.000
  306. D = .5
  307. ###D = 0.000
  308. FF0 = 0.000
  309. FF1 = .5
  310. ###FF1 = 0.000
  311. FF2 = 0.0
  312. BIAS = 0.000
  313.  
  314. ###############################################################################
  315. # section for main IO controller parameters
  316. ###############################################################################
  317. [EMCIO]
  318.  
  319. #- Name of IO controller program, e.g., io
  320. EMCIO = io
  321.  
  322. #- cycle time, in seconds
  323. CYCLE_TIME = 0.100
  324.  
  325. #- tool table file
  326. TOOL_TABLE = stg.tbl
Advertisement
Add Comment
Please, Sign In to add comment
Public Pastes
We use cookies for various purposes including analytics. By continuing to use Pastebin, you agree to our use of cookies as described in the Cookies Policy.  OK, I Understand
Not a member of Pastebin yet?
Sign Up, it unlocks many cool features!