Advertisement
Not a member of Pastebin yet?
Sign Up,
it unlocks many cool features!
- Texas Instruments X-Loader 1.4.2 (Sep 7 2009 - 18:18:16)
- Detected Numonyx OneNAND 4G Flash
- Reading boot sector
- Loading u-boot.bin from mmc
- U-Boot 2009.08-0-dirty (Sep 22 2009 - 13:31:59)
- OMAP3530-GP ES3.1, CPU-OPP2 L3-165MHz
- IGEP v2.x rev. B + LPDDR/ONENAND
- DRAM: 512 MB
- Muxed OneNAND(DDP) 512MB 1.8V 16-bit (0x58)
- OneNAND version = 0x0031
- Chip support all block unlock
- Chip has 2 plane
- Scanning device for bad blocks
- Bad eraseblock 1686 at 0x0d2c0000
- Bad eraseblock 1687 at 0x0d2e0000
- OneNAND: 512 MB
- In: serial
- Out: serial
- Err: serial
- Die ID #7c06000400000000040373051301d016
- Net: smc911x-0
- Hit any key to stop autoboot: 3 2 1 0
- mmc0 is available
- reading setup.ini
- 445 bytes read
- ## Executing script at 80000000
- ===== Setup boot settings =====
- ===== Load uImage from mmc =====
- reading uImage.bin
- 2342488 bytes read
- ## Booting kernel from Legacy Image at 80200000 ...
- Image Name: Linux-2.6.28.10
- Image Type: ARM Linux Kernel Image (uncompressed)
- Data Size: 2342424 Bytes = 2.2 MB
- Load Address: 80008000
- Entry Point: 80008000
- Verifying Checksum ... OK
- Loading Kernel Image ... OK
- OK
- Starting kernel ...
- Uncompressing Linux..................................................................................................................................................... done, booting the kernel.
- [ 0.000000] Linux version 2.6.28.10 (eballetbo@jupiter) (gcc version 4.3.2 (GCC) ) #1 Mon Nov 9 12:09:53 CET 2009
- [ 0.000000] CPU: ARMv7 Processor [411fc083] revision 3 (ARMv7), cr=10c5387f
- [ 0.000000] CPU: VIPT nonaliasing data cache, VIPT nonaliasing instruction cache
- [ 0.000000] Machine: IGEP v2.x board
- [ 0.000000] Memory policy: ECC disabled, Data cache writeback
- [ 0.000000] OMAP3430 ES3.1
- [ 0.000000] SRAM: Mapped pa 0x40200000 to va 0xd7000000 size: 0x100000
- [ 0.000000] Reserving 4194304 bytes SDRAM for VRAM
- [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 130048
- [ 0.000000] Kernel command line: mem=512M console=ttyS2,115200n8 console=tty0 omapfb.mode=dvi:1280x720-16@60 root=/dev/mmcblk0p2 rw rootwait
- [ 0.000000] Clocking rate (Crystal/DPLL/ARM core): 26.0/332/500 MHz
- [ 0.000000] GPMC revision 5.0
- [ 0.000000] IRQ: Found an INTC at 0xd8200000 (revision 4.0) with 96 interrupts
- [ 0.000000] Total of 96 interrupts on 1 active controller
- [ 0.000000] OMAP34xx GPIO hardware version 2.5
- [ 0.000000] PID hash table entries: 2048 (order: 11, 8192 bytes)
- [ 0.000000] OMAP clockevent source: GPTIMER12 at 32768 Hz
- [ 0.000000] Console: colour dummy device 80x30
- [ 0.000000] console [tty0] enabled
- [ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
- [ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
- [ 0.000000] Memory: 512MB = 512MB total
- [ 0.000000] Memory: 510464KB available (4284K code, 511K data, 168K init)
- [ 0.000000] Calibrating delay loop... 496.77 BogoMIPS (lpj=1937408)
- [ 0.000000] Mount-cache hash table entries: 512
- [ 0.000000] CPU: Testing write buffer coherency: ok
- [ 0.000000] net_namespace: 532 bytes
- [ 0.000000] regulator: core version 0.5
- [ 0.000000] NET: Registered protocol family 16
- [ 12.050170] OMAP DMA hardware revision 4.0
- [ 12.051208] USB: No board-specific platform config found
- [ 12.129272] OMAP DSS rev 2.0
- [ 12.129425] OMAP DISPC rev 3.0
- [ 12.129577] OMAP DSI rev 1.0
- [ 12.131774] i2c_omap i2c_omap.1: bus 1 rev3.12 at 2600 kHz
- [ 12.135223] twl4030: PIH (irq 7) chaining IRQs 368..375
- [ 12.135253] twl4030: power (irq 373) chaining IRQs 376..383
- [ 12.135772] twl4030: gpio (irq 368) chaining IRQs 384..401
- [ 12.152587] i2c_omap i2c_omap.3: bus 3 rev3.12 at 100 kHz
- [ 12.154266] SCSI subsystem initialized
- [ 12.156555] twl4030_usb twl4030_usb: Initialized TWL4030 USB module
- [ 12.157836] usbcore: registered new interface driver usbfs
- [ 12.158355] usbcore: registered new interface driver hub
- [ 12.158721] usbcore: registered new device driver usb
- [ 12.158752] musb_hdrc: version 6.0, musb-dma, otg (peripheral+host), debug=0
- [ 12.159454] musb_hdrc: USB OTG mode controller at d80ab000 using DMA, IRQ 92
- [ 12.161499] regulator: VMMC1: 1850 <--> 3150 mV normal standby
- [ 12.161987] regulator: VUSB1V5: 1500 mV normal standby
- [ 12.162414] regulator: VUSB1V8: 1800 mV normal standby
- [ 12.162841] regulator: VUSB3V1: 3100 mV normal standby
- [ 12.222473] cfg80211: Using static regulatory domain info
- [ 12.222534] cfg80211: Regulatory domain: US
- [ 12.222534] (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
- [ 12.222595] (2402000 KHz - 2472000 KHz @ 40000 KHz), (600 mBi, 2700 mBm)
- [ 12.222625] (5170000 KHz - 5190000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)
- [ 12.222656] (5190000 KHz - 5210000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)
- [ 12.222686] (5210000 KHz - 5230000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)
- [ 12.222747] (5230000 KHz - 5330000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)
- [ 12.222778] (5735000 KHz - 5835000 KHz @ 40000 KHz), (600 mBi, 3000 mBm)
- [ 12.222808] cfg80211: Calling CRDA for country: US
- [ 12.226318] NET: Registered protocol family 2
- [ 12.292663] IP route cache hash table entries: 16384 (order: 4, 65536 bytes)
- [ 12.293334] TCP established hash table entries: 65536 (order: 7, 524288 bytes)
- [ 12.295013] TCP bind hash table entries: 65536 (order: 6, 262144 bytes)
- [ 12.295989] TCP: Hash tables configured (established 65536 bind 65536)
- [ 12.296020] TCP reno registered
- [ 12.316070] NET: Registered protocol family 1
- [ 12.319305] VFS: Disk quotas dquot_6.5.1
- [ 12.319427] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
- [ 12.320526] JFFS2 version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, Inc.
- [ 12.324981] msgmni has been set to 997
- [ 12.333312] alg: No test for stdrng (krng)
- [ 12.333465] io scheduler noop registered
- [ 12.333496] io scheduler anticipatory registered
- [ 12.333526] io scheduler deadline registered
- [ 12.333740] io scheduler cfq registered (default)
- [ 12.353637] Serial: 8250/16550 driver4 ports, IRQ sharing enabled
- [ 12.375854] serial8250.0: ttyS0 at MMIO 0x4806a000 (irq = 72) is a ST16654
- [ 12.396728] serial8250.0: ttyS1 at MMIO 0x4806c000 (irq = 73) is a ST16654
- [ 12.417846] serial8250.0: ttyS2 at MMIO 0x49020000 (irq = 74) is a ST16654
- [ 12.417907] console [ttyS2] enabled
- [ 12.878601] brd: module loaded
- [ 12.886901] loop: module loaded
- [ 12.890167] smsc911x: Driver version 2008-10-21.
- [ 12.897430] smsc911x-mdio: probed
- [ 12.900878] eth0: attached PHY driver [Generic PHY] (mii_bus:phy_addr=ffffffff:01, irq=-1)
- [ 12.909515] net eth0: MAC Address: ee:1f:35:7e:7d:a8
- [ 12.915069] i2c /dev entries driver
- [ 12.920715] input: triton2-pwrbutton as /devices/virtual/input/input0
- [ 12.964355] triton2 power button driver initialized
- [ 12.969299] st: Version 20080504, fixed bufsize 32768, s/g segs 256
- [ 12.975891] Driver 'st' needs updating - please use bus_type methods
- [ 12.982574] osst :I: Tape driver with OnStream support version 0.99.4
- [ 12.982604] osst :I: $Id: osst.c,v 1.73 2005/01/01 21:13:34 wriede Exp $
- [ 12.996093] Driver 'osst' needs updating - please use bus_type methods
- [ 13.003112] Driver 'sd' needs updating - please use bus_type methods
- [ 13.009765] Driver 'sr' needs updating - please use bus_type methods
- [ 13.016693] SCSI Media Changer driver v0.25
- [ 13.021270] Driver 'ch' needs updating - please use bus_type methods
- [ 13.028350] omap2-nand driver initializing
- [ 13.032989] OneNAND driver initializing
- [ 13.037933] omap2-onenand omap2-onenand: initializing on CS0, phys base 0x20000000, virtual base d0900000
- [ 13.047729] Muxed OneNAND(DDP) 512MB 1.8V 16-bit (0x58)
- [ 13.053039] OneNAND version = 0x0031
- [ 13.057922] block = 2048, wp status = 0x2
- [ 13.066253] Scanning device for bad blocks
- [ 13.142700] Bad eraseblock 1686 at 0x0d2c0000
- [ 13.251617] Creating 5 MTD partitions on "omap2-onenand":
- [ 13.257080] 0x00000000-0x00080000 : "X-Loader"
- [ 13.263305] 0x00080000-0x00260000 : "U-Boot"
- [ 13.268676] 0x00260000-0x00280000 : "U-Boot Env"
- [ 13.273376] mtd: partition "U-Boot Env" doesn't start on an erase block boundary -- force read-only
- [ 13.283630] 0x00280000-0x00780000 : "Kernel"
- [ 13.289062] 0x00780000-0x20000000 : "File System"
- [ 13.297882] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
- [ 13.304870] ehci-omap ehci-omap.0: OMAP-EHCI Host Controller
- [ 13.311462] ehci-omap ehci-omap.0: new USB bus registered, assigned bus number 1
- [ 13.319335] ehci-omap ehci-omap.0: irq 77, io mem 0x48064800
- [ 13.339355] ehci-omap ehci-omap.0: USB 2.0 started, EHCI 1.00
- [ 13.345825] usb usb1: configuration #1 chosen from 1 choice
- [ 13.351898] hub 1-0:1.0: USB hub found
- [ 13.355804] hub 1-0:1.0: 3 ports detected
- [ 13.361511] Initializing USB Mass Storage driver...
- [ 13.366821] usbcore: registered new interface driver usb-storage
- [ 13.372955] USB Mass Storage support registered.
- [ 13.377899] usbcore: registered new interface driver libusual
- [ 13.383819] g_ether gadget: using random self ethernet address
- [ 13.389739] g_ether gadget: using random host ethernet address
- [ 13.396453] usb0: MAC b2:4b:fa:03:53:1c
- [ 13.400329] usb0: HOST MAC fe:d9:53:a5:cc:35
- [ 13.404754] g_ether gadget: Ethernet Gadget, version: Memorial Day 2008
- [ 13.411499] g_ether gadget: g_ether ready
- [ 13.415557] musb_hdrc musb_hdrc: MUSB HDRC host driver
- [ 13.421478] musb_hdrc musb_hdrc: new USB bus registered, assigned bus number 2
- [ 13.429412] usb usb2: configuration #1 chosen from 1 choice
- [ 13.435455] hub 2-0:1.0: USB hub found
- [ 13.439331] hub 2-0:1.0: 1 port detected
- [ 13.445037] mice: PS/2 mouse device common for all mice
- [ 13.481201] twl4030_rtc twl4030_rtc: rtc core: registered twl4030_rtc as rtc0
- [ 13.488586] twl4030_rtc twl4030_rtc: Power up reset detected.
- [ 13.494720] twl4030_rtc twl4030_rtc: Enabling TWL4030-RTC.
- [ 13.502380] OMAP Watchdog Timer Rev 0x31: initial timeout 60 sec
- [ 13.509277] mmci-omap-hs mmci-omap-hs.0: Failed to get debounce clock
- [ 13.620849] mmci-omap-hs mmci-omap-hs.1: Failed to get debounce clock
- [ 13.629241] usbcore: registered new interface driver usbhid
- [ 13.634857] usbhid: v2.6:USB HID core driver
- [ 13.639556] Advanced Linux Sound Architecture Driver Version 1.0.18rc3.
- [ 13.646728] ASoC version 0.13.2
- [ 13.650177] IGEP v2.x SoC init
- [ 13.653625] TWL4030 Audio Codec init
- [ 13.658843] asoc: twl4030 <-> omap-mcbsp-dai-(link_id) mapping ok
- [ 13.677154] ALSA device list:
- [ 13.680145] #0: igep (twl4030)
- [ 13.683898] oprofile: using arm/armv7
- [ 13.687866] TCP cubic registered
- [ 13.691192] NET: Registered protocol family 17
- [ 13.695709] NET: Registered protocol family 15
- [ 13.700683] RPC: Registered udp transport module.
- [ 13.705444] RPC: Registered tcp transport module.
- [ 13.710296] ieee80211: 802.11 data/management/control stack, git-1.1.13
- [ 13.717041] ieee80211: Copyright (C) 2004-2005 Intel Corporation <jketreno@linux.intel.com>
- [ 13.725555] ThumbEE CPU extension supported.
- [ 13.729858] Power Management for TI OMAP3.
- [ 13.746704] SmartReflex driver initialized
- [ 13.757507] Disabling unused clock "sr2_fck"
- [ 13.761932] Disabling unused clock "sr1_fck"
- [ 13.766265] Disabling unused clock "mcbsp_fck"
- [ 13.770782] Disabling unused clock "mcbsp_fck"
- [ 13.775268] Disabling unused clock "mcbsp_fck"
- [ 13.779815] Disabling unused clock "mcbsp_ick"
- [ 13.784301] Disabling unused clock "mcbsp_ick"
- [ 13.788818] Disabling unused clock "mcbsp_ick"
- [ 13.793334] Disabling unused clock "gpt2_ick"
- [ 13.797729] Disabling unused clock "gpt3_ick"
- [ 13.802154] Disabling unused clock "gpt4_ick"
- [ 13.806549] Disabling unused clock "gpt5_ick"
- [ 13.810974] Disabling unused clock "gpt6_ick"
- [ 13.815368] Disabling unused clock "gpt7_ick"
- [ 13.819793] Disabling unused clock "gpt8_ick"
- [ 13.824218] Disabling unused clock "gpt9_ick"
- [ 13.828613] Disabling unused clock "wdt3_ick"
- [ 13.833038] Disabling unused clock "wdt3_fck"
- [ 13.837432] Disabling unused clock "gpio2_dbck"
- [ 13.842041] Disabling unused clock "gpio3_dbck"
- [ 13.846618] Disabling unused clock "gpio4_dbck"
- [ 13.851226] Disabling unused clock "gpio5_dbck"
- [ 13.855804] Disabling unused clock "gpio6_dbck"
- [ 13.860382] Disabling unused clock "gpt9_fck"
- [ 13.864807] Disabling unused clock "gpt8_fck"
- [ 13.869201] Disabling unused clock "gpt7_fck"
- [ 13.873626] Disabling unused clock "gpt6_fck"
- [ 13.878021] Disabling unused clock "gpt5_fck"
- [ 13.882446] Disabling unused clock "gpt4_fck"
- [ 13.886871] Disabling unused clock "gpt3_fck"
- [ 13.891265] Disabling unused clock "gpt2_fck"
- [ 13.895721] Disabling unused clock "gpt1_ick"
- [ 13.900115] Disabling unused clock "wdt1_ick"
- [ 13.904541] Disabling unused clock "wdt2_ick"
- [ 13.908935] Disabling unused clock "wdt2_fck"
- [ 13.913360] Disabling unused clock "gpio1_dbck"
- [ 13.917968] Disabling unused clock "gpt1_fck"
- [ 13.922363] Disabling unused clock "cam_ick"
- [ 13.926727] Disabling unused clock "cam_mclk"
- [ 13.931152] Disabling unused clock "des1_ick"
- [ 13.935577] Disabling unused clock "sha11_ick"
- [ 13.940063] Disabling unused clock "rng_ick"
- [ 13.944396] Disabling unused clock "aes1_ick"
- [ 13.948822] Disabling unused clock "ssi_ick"
- [ 13.953125] Disabling unused clock "mailboxes_ick"
- [ 13.957977] Disabling unused clock "mcbsp_ick"
- [ 13.962463] Disabling unused clock "mcbsp_ick"
- [ 13.966979] Disabling unused clock "gpt10_ick"
- [ 13.971466] Disabling unused clock "gpt11_ick"
- [ 13.975982] Disabling unused clock "i2c_ick"
- [ 13.980316] Disabling unused clock "mcspi_ick"
- [ 13.984802] Disabling unused clock "mcspi_ick"
- [ 13.989318] Disabling unused clock "mcspi_ick"
- [ 13.993804] Disabling unused clock "mcspi_ick"
- [ 13.998321] Disabling unused clock "hdq_ick"
- [ 14.002624] Disabling unused clock "mspro_ick"
- [ 14.007141] Disabling unused clock "des2_ick"
- [ 14.011566] Disabling unused clock "sha12_ick"
- [ 14.016052] Disabling unused clock "aes2_ick"
- [ 14.020477] Disabling unused clock "icr_ick"
- [ 14.024780] Disabling unused clock "pka_ick"
- [ 14.029113] Disabling unused clock "ssi_ssr_fck"
- [ 14.033782] Disabling unused clock "hdq_fck"
- [ 14.038116] Disabling unused clock "mcspi_fck"
- [ 14.042633] Disabling unused clock "mcspi_fck"
- [ 14.047119] Disabling unused clock "mcspi_fck"
- [ 14.051605] Disabling unused clock "mcspi_fck"
- [ 14.056091] Disabling unused clock "mcbsp_fck"
- [ 14.060607] Disabling unused clock "mcbsp_fck"
- [ 14.065093] Disabling unused clock "i2c_fck"
- [ 14.069427] Disabling unused clock "mspro_fck"
- [ 14.073944] Disabling unused clock "gpt11_fck"
- [ 14.078430] Disabling unused clock "gpt10_fck"
- [ 14.082946] Disabling unused clock "dpll4_m6x2_ck"
- [ 14.087799] Disabling unused clock "dpll3_m3x2_ck"
- [ 14.092651] Disabling unused clock "sys_clkout1"
- [ 14.097381] VFP support v0.3: implementor 41 architecture 3 part 30 variant c rev 1
- [ 14.153717] Console: switching to colour frame buffer device 160x45
- [ 14.176391] clock: clksel_round_rate_div: dpll4_m4_ck target_rate 48000000
- [ 14.183502] clock: new_div = 9, new_rate = 48000000
- [ 14.191711] twl4030_rtc twl4030_rtc: setting system clock to 2000-01-01 00:00:00 UTC (946684800)
- [ 14.201141] Waiting for root device /dev/mmcblk0p2...
- [ 14.331756] usb 2-1: new high speed USB device using musb_hdrc and address 2
- [ 14.489959] usb 2-1: configuration #1 chosen from 1 choice
- [ 14.496337] hub 2-1:1.0: USB hub found
- [ 14.500518] hub 2-1:1.0: 4 ports detected
- [ 14.550415] mmc0: host does not support reading read-only switch. assuming write-enable.
- [ 14.558837] mmc0: new high speed SD card at address 1234
- [ 14.564971] mmcblk0: mmc0:1234 SA02G 1.83 GiB
- [ 14.569915] mmcblk0: p1 p2
- [ 14.629364] mmc1: new SDIO card at address 0001
- [ 14.792846] usb 2-1.2: new low speed USB device using musb_hdrc and address 3
- [ 14.915710] usb 2-1.2: device v04fc p05d8 is not supported
- [ 14.926055] usb 2-1.2: configuration #1 chosen from 1 choice
- [ 20.715972] kjournald starting. Commit interval 5 seconds
- [ 21.133850] EXT3 FS on mmcblk0p2, internal journal
- [ 21.142761] EXT3-fs: recovery complete.
- [ 21.155609] EXT3-fs: mounted filesystem with ordered data mode.
- [ 21.165832] VFS: Mounted root (ext3 filesystem).
- [ 21.174865] Freeing init memory: 168K
- [ 22.178344] udev: starting version 151
- [ 36.877471] bluetooth: version magic '2.6.28.10 mod_unload modversions ARMv7 ' should be '2.6.28.10 mod_unload ARMv7 '
- [ 36.895538] l2cap: version magic '2.6.28.10 mod_unload modversions ARMv7 ' should be '2.6.28.10 mod_unload ARMv7 '
- [ 36.914001] hidp: version magic '2.6.28.10 mod_unload modversions ARMv7 ' should be '2.6.28.10 mod_unload ARMv7 '
- [ 36.936340] bluetooth: version magic '2.6.28.10 mod_unload modversions ARMv7 ' should be '2.6.28.10 mod_unload ARMv7 '
- [ 36.949951] l2cap: version magic '2.6.28.10 mod_unload modversions ARMv7 ' should be '2.6.28.10 mod_unload ARMv7 '
- [ 36.972015] rfcomm: version magic '2.6.28.10 mod_unload modversions ARMv7 ' should be '2.6.28.10 mod_unload ARMv7 '
- .-------.
- | | .-.
- | | |-----.-----.-----.| | .----..-----.-----.
- | | | __ | ---'| '--.| .-'| | |
- | | | | | |--- || --'| | | ' | | | |
- '---'---'--'--'--. |-----''----''--' '-----'-'-'-'
- -' |
- '---'
- The Angstrom Distribution igep0020 ttyS2
- Angstrom 2010.7-test-20100709 igep0020 ttyS2
- igep0020 login:
Advertisement
Add Comment
Please, Sign In to add comment
Advertisement