Advertisement
Not a member of Pastebin yet?
Sign Up,
it unlocks many cool features!
- Please choose the operation:
- 1: Load system code to SDRAM via TFTP.
- 2: Load system code then write to Flash via TFTP.
- 3: Boot system code via Flash (default).
- 4: Entr boot command line interface.
- 9: Load Boot Loader code then write to Flash via TFTP.
- You choosed (0)
- 0 seconds ...
- Eth0 (10/100-M) : ethaddr = ("1c:bd:b9:b3:32:8e") 1C BD B9 B3 32 8E
- 3: System Boot system code via Flash.
- ## Powering down port 0 ~ 3.
- ## Booting image at bf050000 ...
- Image Name: DD-WRT v24 Linux Kernel Image
- Created: 2015-04-09 5:44:03 UTC
- System Control Status = 0x00440000
- Image Type: MIPS Linux Kernel Image (lzma compressed)
- Data Size: 836966 Bytes = 817.3 kB
- Load Address: 80000000
- Entry Point: 80004d70
- Verifying Checksum ... OK
- Uncompressing Kernel Image ... OK
- Starting kernel ...
- Linux version 3.2.68 (root@dd-wrt) (gcc version 4.8.3 (OpenWrt/Linaro GCC 4.8-2014.01 r39555) ) #15445 Thu Apr 9 07:43:42 CEST 2
- 015
- bootconsole [early0] enabled
- CPU revision is: 0001964c (MIPS 24KEc)
- Ralink RT3052 id:1 rev:3 running at 384.00 MHz
- Determined physical RAM map:
- memory: 02000000 @ 00000000 (usable)
- Zone PFN ranges:
- Normal 0x00000000 -> 0x00002000
- Movable zone start PFN for each node
- early_node_map[1] active PFN ranges
- 0: 0x00000000 -> 0x00002000
- Built 1 zonelists in Zone order, mobility grouping on. Total pages: 8128
- Kernel command line: console=ttyS1,57600n8 root=/dev/mtdblock4 rootfstype=squashfs noinitrd
- PID hash table entries: 128 (order: -3, 512 bytes)
- Dentry cache hash table entries: 4096 (order: 2, 16384 bytes)
- Inode-cache hash table entries: 2048 (order: 1, 8192 bytes)
- Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
- Primary data cache 16kB, 4-way, VIPT, no aliases, linesize 32 bytes
- Writing ErrCtl register=0000ad08
- Readback ErrCtl register=0000ad08
- Memory: 29764k/32768k available (2001k kernel code, 3004k reserved, 287k data, 156k init, 0k highmem)
- NR_IRQS:48
- console [ttyS1] enabled, bootconsole disabled
- console [ttyS1] enabled, bootconsole disabled
- Calibrating delay loop... 255.59 BogoMIPS (lpj=1277952)
- pid_max: default: 32768 minimum: 301
- Mount-cache hash table entries: 512
- NET: Registered protocol family 16
- bio: create slab <bio-0> at 0
- Switching to clocksource MIPS
- NET: Registered protocol family 2
- IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
- TCP established hash table entries: 1024 (order: 1, 8192 bytes)
- TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
- TCP: Hash tables configured (established 1024 bind 1024)
- TCP reno registered
- UDP hash table entries: 256 (order: 0, 4096 bytes)
- UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
- NET: Registered protocol family 1
- squashfs: version 3.0 (2006/03/15) Phillip Lougher
- msgmni has been set to 58
- io scheduler noop registered
- io scheduler deadline registered (default)
- Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
- serial8250: ttyS0 at MMIO 0x10000500 (irq = 13) is a 16550A
- serial8250: ttyS1 at MMIO 0x10000c00 (irq = 20) is a 16550A
- Ralink gpio driver initialized
- system type: RT3052
- boot type: 0
- ralink flash device: 0x1000000 at 0xbf000000
- Ralink SoC physically mapped flash: Found 1 x16 devices at 0x0 in 16-bit bank. Manufacturer ID 0x0000c2 Chip ID 0x0022a8
- Amd/Fujitsu Extended Query Table at 0x0040
- Amd/Fujitsu Extended Query version 1.1.
- number of CFI chips: 1
- found squashfs at 11D000
- Creating 6 MTD partitions on "Ralink SoC physically mapped flash":
- 0x000000000000-0x000000030000 : "uboot"
- 0x000000030000-0x000000040000 : "uboot-config"
- 0x000000040000-0x000000050000 : "factory-defaults"
- 0x000000050000-0x0000003f0000 : "linux"
- 0x00000011d000-0x0000003f0000 : "rootfs"
- mtd: partition "rootfs" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
- 0x0000003f0000-0x000000400000 : "nvram"
- tun: Universal TUN/TAP device driver, 1.6
- tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
- PPP generic driver version 2.4.2
- PPP BSD Compression module registered
- PPP Deflate Compression module registered
- PPP MPPE Compression module registered
- NET: Registered protocol family 24
- Ralink APSoC Hardware Watchdog Timer
- u32 classifier
- Performance counters on
- Actions configured
- Netfilter messages via NETLINK v0.30.
- nf_conntrack version 0.5.0 (465 buckets, 1860 max)
- ctnetlink v0.93: registering with nfnetlink.
- IPv4 over IPv4 tunneling driver
- ip_tables: (C) 2000-2006 Netfilter Core Team
- IPP2P v0.8.2 loading
- ipt_CLUSTERIP: ClusterIP Version 0.8 loaded successfully
- TCP bic registered
- TCP cubic registered
- TCP westwood registered
- TCP highspeed registered
- TCP hybla registered
- TCP htcp registered
- TCP vegas registered
- TCP scalable registered
- NET: Registered protocol family 17
- Bridge firewalling registered
- 8021q: 802.1Q VLAN Support v1.8
- searching for nvram
- nvram size = 0
- MAC_ADRH -- : 0x0000000c
- MAC_ADRL -- : 0x43305277
- MAC_ADRH -- : 0x0000000c
- MAC_ADRL -- : 0x43305277
- Ralink APSoC Ethernet Driver Initilization. v2.0 256 rx/tx descriptors allocated, mtu = 1500!
- NAPI enable, Tx Ring = 256, Rx Ring = 256
- MAC_ADRH -- : 0x0000000c
- MAC_ADRL -- : 0x43305277
- rt3052 access driver initialization.
- VFS: Mounted root (squashfs filesystem) readonly on device 31:4.
- Freeing unused kernel memory: 156k freed
- start service
- starting Architecture code for rt2880
- Jan 1 00:00:01 udevtrigger[46]: parse_config_file: can't open '/etc/udev/udev.conf' as config file: No such file or directory
- /bin/sh: can't create /sys/class/net/eth2/queues/rx-0/rps_cpus: nonexistent directory
- /bin/sh: can't create /sys/class/net/lo/queues/rx-0/rps_cpus: nonexistent directory
- /bin/sh: can't create /sys/class/net/teql0/queues/rx-0/rps_cpus: nonexistent directory
- /bin/sh: can't create /sys/class/net/tunl0/queues/rx-0/rps_cpus: nonexistent directory
- /bin/sh: can't create /sys/class/net/lo/queues/tx-0/xps_cpus: nonexistent directory
- /bin/sh: can't create /sys/class/net/teql0/queues/tx-0/xps_cpus: nonexistent directory
- /bin/sh: can't create /sys/class/net/eth2/queues/tx-0/xps_cpus: nonexistent directory
- /bin/sh: can't create /sys/class/net/tunl0/queues/tx-0/xps_cpus: nonexistent directory
- Started WatchDog Timer.
- 4MAC_ADRH -- : 0x00001cbd
- MAC_ADRL -- : 0xb9b3328e
- phy_tx_ring = 0x01f82000, tx_ring = 0xa1f82000
- phy_rx_ring0 = 0x01f83000, rx_ring0 = 0xa1f83000
- RT305x_ESW: Link Status Changed
- CDMA_CSG_CFG = 81000007
- GDMA1_FWD_CFG = 710000
- switch reg write offset=14, value=405555
- /bin/sh: can't create /sys/class/net/vlan2/queues/rx-0/rps_cpus: nonexistent directory
- /bin/sh: can't create /sys/class/net/vlan2/queues/tx-0/xps_cpus: nonexistent directory
- /bin/sh: can't create /sys/class/net/vlan1/queues/rx-0/rps_cpus: nonexistent directory
- /bin/sh: can't create /sys/class/net/vlan1/queues/tx-0/xps_cpus: nonexistent directory
- switch reg write offset=50, value=2001
- switch reg write offset=90, value=7f7f
- switch reg write offset=98, value=7f3f
- switch reg write offset=e4, value=3f
- switch reg write offset=40, value=1001
- switch reg write offset=44, value=1001
- switch reg write offset=48, value=1002
- switch reg write offset=70, value=ffff506f
- device br0 entered promiscuous mode
- /bin/sh: can't create /sys/class/net/br0/queues/rx-0/rps_cpus: nonexistent directory
- /bin/sh: can't create /sys/class/net/br0/queues/tx-0/xps_cpus: nonexistent directory
- device vlan1 entered promiscuous mode
- device eth2 entered promiscuous mode
- device vlan2 entered promiscuous mode
- /bin/sh: ead: not foundbr0: port 2(vlan2) entering forwarding state
- br0: port 2(vlan2) entering forwarding state
- br0: port 1(vlan1) entering forwarding state
- br0: port 1(vlan1) entering forwarding state
- device br0 left promiscuous mode
- device br0 entered promiscuous mode
- rt2860v2_ap: module license 'unspecified' taints kernel.
- Disabling lock debugging due to kernel taint
- 0x1300 = 00064380
- /bin/sh: can't create /sys/class/net/ra0/queues/rx-0/rps_cpus: nonexistent directory
- /bin/sh: can't create /sys/class/net/ra0/queues/tx-0/xps_cpus: nonexistent directory
- /bin/sh: can't create /sys/class/net/wds0/queues/rx-0/rps_cpus: nonexistent directory
- br0: port 2(vlan2) entering forwarding state
- br0: port 1(vlan1) entering forwarding state
- /bin/sh: can't create /sys/class/net/wds4/queues/rx-0/rps_cpus: nonexistent directory
- /bin/sh: can't create /sys/class/net/apcli0/queues/rx-0/rps_cpus: nonexistent directory
- /bin/sh: can't create /sys/class/net/wds2/queues/rx-0/rps_cpus: nonexistent directory
- /bin/sh: can't create /sys/class/net/wds0/queues/tx-0/xps_cpus: nonexistent directory
- /bin/sh: can't create /sys/class/net/wds1/queues/rx-0/rps_cpus: nonexistent directory
- /bin/sh: can't create /sys/class/net/wds4/queues/tx-0/xps_cpus: nonexistent directory
- /bin/sh: can't create /sys/class/net/wds8/queues/rx-0/rps_cpus: nonexistent directory
- /bin/sh: can't create /sys/class/net/wds1/queues/tx-0/xps_cpus: nonexistent directory
- /bin/sh: can't create /sys/class/net/wds8/queues/tx-0/xps_cpus: nonexistent directory
- /bin/sh: can't create /sys/class/net/apcli0/queues/tx-0/xps_cpus: nonexistent directory
- /bin/sh: can't create /sys/class/net/wds7/queues/rx-0/rps_cpus: nonexistent directory
- /bin/sh: can't create /sys/class/net/wds5/queues/rx-0/rps_cpus: nonexistent directory
- /bin/sh: can't create /sys/class/net/wds2/queues/tx-0/xps_cpus: nonexistent directory
- /bin/sh: can't create /sys/class/net/wds3/queues/rx-0/rps_cpus: nonexistdevice ra0 entered promiscuous mode
- ent directory
- /br0: port 3(ra0) entering forwarding state
- bin/sh: can't crbr0: port 3(ra0) entering forwarding state
- eate /sys/class/net/wds6/queues/rx-0/rps_cpus: nonexistent directory
- /bin/sh: can't create /sys/class/net/wds6/queues/tx-0/xps_cpus: nonexistent directory
- /bin/sh: can't create /sys/class/net/wds7/queues/tx-0/xps_cpus: nonexistent directory
- /bin/sh: can't create /sys/class/net/wds3/qudevice ra1 entered promiscuous mode
- eues/tx-0/xps_cpbr0: port 4(ra1) entering forwarding state
- us: nonexistent br0: port 4(ra1) entering forwarding state
- directory
- /bin/sh: can't create /sys/class/net/wds5/queues/tx-0/xps_cpus: nonexistent directory
- /bin/sh: can't create /sys/class/net/ra1/queues/rx-0/rps_cpus: nonexistent directory
- /bin/sh: can't create /sys/class/net/ra1/queues/tx-0/xps_cpus: nonexistent directory
- device br0 left promiscuous mode
- wland: No such file or directory
- /bin/sh: can't create /proc/sys/net/ipv4/conf/br0/loop: nonexistent directory
- br0: port 3(ra0) entering forwarding state
- br0: port 4(ra1) entering forwarding state
- /bin/sh: can't create /proc/sys/net/ipv4/netfilter/ip_conntrack_udp_timeouts: nonexistent directory
- ba0 no private ioctls.
- ba0 no private ioctls.
- ba0 no private ioctls.
- ba0 no private ioctls.
- /opt/etc/init.d/rcS: No such file or directory
- /jffs/etc/init.d/rcS: No such file or directory
- /mmc/etc/init.d/rcS: No such file or directory
- apcli0: No such process
- apcli0: No such process
- /bin/sh: can't create /proc/sys/net/ipv4/conf/br0/loop: nonexistent directory
- /bin/sh: can't create /proc/sys/net/ipv4/netfilter/ip_conntrack_udp_timeouts: nonexistent directory
- wland: No such file or directory
Advertisement
Add Comment
Please, Sign In to add comment
Advertisement