CM-FX6 # boot
mmc2 is current device
reading boot.scr

** Unable to read "boot.scr" from mmc 2:1 **
reading uImage-cm-fx6

3892932 bytes read
Booting from mmc ...
## Booting kernel from Legacy Image at 10800000 ...
   Image Name:   Linux-3.0.35-03056-g590fc4c
   Image Type:   ARM Linux Kernel Image (uncompressed)
   Data Size:    3892868 Bytes =  3.7 MB
   Load Address: 10008000
   Entry Point:  10008000
   Verifying Checksum ... OK
   Loading Kernel Image ... OK
OK

Starting kernel ...

Linux version 3.0.35-03056-g590fc4c (meow@kaliss) (gcc version 4.8.1 (Sourcery CodeBench Lite 2013.11-33) ) #1 SMP PREEMPT Tue Apr 8 13:44:40 EDT 2014
CPU: ARMv7 Processor [412fc09a] revision 10 (ARMv7), cr=10c53c7d
CPU: VIPT nonaliasing data cache, VIPT aliasing instruction cache
Machine: Compulab Utilite
Memory policy: ECC disabled, Data cache writealloc
CPU identified as i.MX6Q, silicon rev 1.2
PERCPU: Embedded 7 pages/cpu @8ce10000 s5440 r8192 d15040 u32768
Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 453120
Kernel command line: console=ttymxc3,115200 root=/dev/mmcblk0p2 rw rootwait mxcfb0:dev=hdmi,1280x720M@60,if=RGB24
PID hash table entries: 4096 (order: 2, 16384 bytes)
Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
Memory: 512MB 256MB 1024MB = 1792MB total
Memory: 1806208k/1806208k available, 290944k reserved, 1048576K highmem
Virtual kernel memory layout:
    vector  : 0xffff0000 - 0xffff1000   (   4 kB)
    fixmap  : 0xfff00000 - 0xfffe0000   ( 896 kB)
    DMA     : 0xf4600000 - 0xffe00000   ( 184 MB)
    vmalloc : 0xc0800000 - 0xf2000000   ( 792 MB)
    lowmem  : 0x80000000 - 0xc0000000   (1024 MB)
    pkmap   : 0x7fe00000 - 0x80000000   (   2 MB)
    modules : 0x7f000000 - 0x7fe00000   (  14 MB)
      .init : 0x80008000 - 0x80039000   ( 196 kB)
      .text : 0x80039000 - 0x80a86c8c   (10552 kB)
      .data : 0x80a88000 - 0x80ae0be0   ( 355 kB)
       .bss : 0x80ae0c04 - 0x80b2adec   ( 297 kB)
SLUB: Genslabs=13, HWalign=32, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
Preemptible hierarchical RCU implementation.
NR_IRQS:624
MXC GPIO hardware
sched_clock: 32 bits at 3000kHz, resolution 333ns, wraps every 1431655ms
arm_max_freq=1.2GHz
MXC_Early serial console at MMIO 0x21f0000 (options '115200')
bootconsole [ttymxc3] enabled
Console: colour dummy device 80x30
Calibrating delay loop... 1581.05 BogoMIPS (lpj=7905280)
pid_max: default: 32768 minimum: 301
Mount-cache hash table entries: 512
CPU: Testing write buffer coherency: ok
hw perfevents: enabled with ARMv7 Cortex-A9 PMU driver, 7 counters available
CPU1: Booted secondary processor
CPU2: Booted secondary processor
CPU3: Booted secondary processor
Brought up 4 CPUs
SMP: Total of 4 processors activated (6324.22 BogoMIPS).
devtmpfs: initialized
print_constraints: dummy:
NET: Registered protocol family 16
print_constraints: vddpu: 725 <--> 1300 mV at 1150 mV fast normal
print_constraints: vddcore: 725 <--> 1300 mV at 1150 mV fast normal
print_constraints: vddsoc: 725 <--> 1300 mV at 1200 mV fast normal
print_constraints: vdd2p5: 2000 <--> 2775 mV at 2400 mV fast normal
print_constraints: vdd1p1: 800 <--> 1400 mV at 1100 mV fast normal
print_constraints: vdd3p0: 2625 <--> 3400 mV at 3000 mV fast normal
hw-breakpoint: found 6 breakpoint and 1 watchpoint registers.
hw-breakpoint: 1 breakpoint(s) reserved for watchpoint single-step.
hw-breakpoint: maximum watchpoint size is 4 bytes.
L310 cache controller enabled
l2x0: 16 ways, CACHE_ID 0x410000c7, AUX_CTRL 0x32070000, Cache size: 1048576 B
bio: create slab <bio-0> at 0
mxs-dma mxs-dma-apbh: initialized
print_constraints: vmmc: 3300 mV
print_constraints: wm8731: 3300 mV
vgaarb: loaded
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
Freescale USB OTG Driver loaded, $Revision: 1.55 $
imx-ipuv3 imx-ipuv3.0: IPU DMFC NORMAL mode: 1(0~1), 5B(4,5), 5F(6,7)
imx-ipuv3 imx-ipuv3.1: IPU DMFC NORMAL mode: 1(0~1), 5B(4,5), 5F(6,7)
MIPI CSI2 driver module loaded
Advanced Linux Sound Architecture Driver Version 1.0.24.
Bluetooth: Core ver 2.16
NET: Registered protocol family 31
Bluetooth: HCI device and connection manager initialized
Bluetooth: HCI socket layer initialized
Bluetooth: L2CAP socket layer initialized
Bluetooth: SCO socket layer initialized
cfg80211: Calling CRDA to update world regulatory domain
i2c-core: driver [max17135] using legacy suspend method
i2c-core: driver [max17135] using legacy resume method
Switching to clocksource mxc_timer1
NET: Registered protocol family 2
IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
TCP bind hash table entries: 65536 (order: 7, 786432 bytes)
TCP: Hash tables configured (established 131072 bind 65536)
TCP reno registered
UDP hash table entries: 512 (order: 2, 16384 bytes)
UDP-Lite hash table entries: 512 (order: 2, 16384 bytes)
NET: Registered protocol family 1
RPC: Registered named UNIX socket transport module.
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
RPC: Registered tcp NFSv4.1 backchannel transport module.
PMU: registered new PMU device of type 0
Static Power Management for Freescale i.MX6
wait mode is enabled for i.MX6
cpaddr = c0880000 suspend_iram_base=c08f0000
PM driver module loaded
IMX usb wakeup probe
add wake up source irq 75
IMX usb wakeup probe
cpu regulator mode:ldo_enable
i.MXC CPU frequency driver
highmem bounce pool size: 64 pages
JFFS2 version 2.2. (NAND) © 2001-2006 Red Hat, Inc.
msgmni has been set to 1479
alg: No test for stdrng (krng)
io scheduler noop registered
io scheduler deadline registered
io scheduler cfq registered (default)
MIPI DSI driver module loaded
mxc_sdc_fb mxc_sdc_fb.0: register mxc display driver hdmi
mxc_hdmi mxc_hdmi: Detected HDMI controller 0x13:0xa:0xa0:0xc1
Console: switching to colour frame buffer device 80x30
mxc_sdc_fb mxc_sdc_fb.1: register mxc display driver dvi
mxc_sdc_fb mxc_sdc_fb.1: NO mxc display driver found!
imx-sdma imx-sdma: loaded firmware 1.1
imx-sdma imx-sdma: initialized
Serial: IMX driver
imx-uart.0: ttymxc0 at MMIO 0x2020000 (irq = 58) is a IMX
imx-uart.3: ttymxc3 at MMIO 0x21f0000 (irq = 61) is a IMX
console [ttymxc3] enabled, bootconsole disabled
console [ttymxc3] enabled, bootconsole disabled
loop: module loaded
at24 2-0050: 256 byte at24 EEPROM, writable, 16 bytes/write
ahci: SSS flag set, parallel bus scan disabled
ahci ahci.0: AHCI 0001.0300 32 slots 1 ports 3 Gbps 0x1 impl platform mode
ahci ahci.0: flags: ncq sntf stag pm led clo only pmp pio slum part ccc apst
scsi0 : ahci_platform
ata1: SATA max UDMA/133 mmio [mem 0x02200000-0x02200fff] port 0x100 irq 71
GPMI NAND driver registered. (IMX)
vcan: Virtual CAN interface driver
CAN device driver interface
flexcan netdevice driver
FEC Ethernet Driver
fec_enet_mii_bus: probed
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
fsl-ehci fsl-ehci.0: Freescale On-Chip EHCI Host Controller
fsl-ehci fsl-ehci.0: new USB bus registered, assigned bus number 1
fsl-ehci fsl-ehci.0: irq 75, io base 0x02184000
fsl-ehci fsl-ehci.0: USB 2.0 started, EHCI 1.00
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 1 port detected
add wake up source irq 72
fsl-ehci fsl-ehci.1: Freescale On-Chip EHCI Host Controller
fsl-ehci fsl-ehci.1: new USB bus registered, assigned bus number 2
fsl-ehci fsl-ehci.1: irq 72, io base 0x02184200
fsl-ehci fsl-ehci.1: USB 2.0 started, EHCI 1.00
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 1 port detected
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
ARC USBOTG Device Controller driver (1 August 2005)
mousedev: PS/2 mouse device common for all mice
i2c-core: driver [isl29023] using legacy suspend method
i2c-core: driver [isl29023] using legacy resume method
i2c /dev entries driver
rtc-em3027 3-0056: rtc core: registered rtc-em3027 as rtc0
at24 3-0050: 256 byte at24 EEPROM, writable, 16 bytes/write
iMX6 PCIe PCIe RC mode imx_pcie_pltfm_probe entering.
PCIE: imx_pcie_pltfm_probe start link up.
ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata1.00: ATA-9: SanDisk SSD U110 32GB, U221000, max UDMA/133
ata1.00: 62533296 sectors, multi 1: LBA48 NCQ (depth 31/32)
ata1.00: configured for UDMA/133
scsi 0:0:0:0: Direct-Access     ATA      SanDisk SSD U110 U221 PQ: 0 ANSI: 5
IMX PCIe port: link up.
PCI: bus0: Fast back to back transfers disabled
sd 0:0:0:0: [sda] 62533296 512-byte logical blocks: (32.0 GB/29.8 GiB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
PCI: bus1: Fast back to back transfers disabled
PCI: Device 0000:00:00.0 not available because of resource collisions
pcieport: probe of 0000:00:00.0 failed with error -22
pci 0000:00:00.0: BAR 0: assigned [mem 0x01000000-0x010fffff 64bit pref]
pci 0000:00:00.0: BAR 0: set to [mem 0x01000000-0x010fffff 64bit pref] (PCI address [0x1000000-0x10fffff])
pci 0000:00:00.0: BAR 8: assigned [mem 0x01100000-0x011fffff]
 sda: sda1 sda2
pci 0000:00:00.0: BAR 6: assigned [mem 0x01200000-0x0120ffff pref]
sd 0:0:0:0: [sda] Attached SCSI disk
pci 0000:00:00.0: BAR 7: assigned [io  0x1e00000-0x1e00fff]
pci 0000:01:00.0: BAR 0: assigned [mem 0x01100000-0x0111ffff]
pci 0000:01:00.0: BAR 0: set to [mem 0x01100000-0x0111ffff] (PCI address [0x1100000-0x111ffff])
pci 0000:01:00.0: BAR 3: assigned [mem 0x01120000-0x01123fff]
pci 0000:01:00.0: BAR 3: set to [mem 0x01120000-0x01123fff] (PCI address [0x1120000-0x1123fff])
pci 0000:01:00.0: BAR 2: assigned [io  0x1e00000-0x1e0001f]
pci 0000:01:00.0: BAR 2: set to [io  0x1e00000-0x1e0001f] (PCI address [0x1e00000-0x1e0001f])
pci 0000:00:00.0: PCI bridge to [bus 01-01]
pci 0000:00:00.0:   bridge window [io  0x1e00000-0x1e00fff]
usb 2-1: new high speed USB device number 2 using fsl-ehci
pci 0000:00:00.0:   bridge window [mem 0x01100000-0x011fffff]
pci 0000:00:00.0:   bridge window [mem pref disabled]
i2c i2c-0: Added multiplexed i2c bus 3
i2c i2c-0: Added multiplexed i2c bus 4
gpio-i2cmux gpio-i2cmux: 2 port mux on imx-i2c adapter
Linux video capture interface: v2.00
mxc_v4l2_output mxc_v4l2_output.0: V4L2 device registered as video16
mxc_v4l2_output mxc_v4l2_output.0: V4L2 device registered as video17
i2c-core: driver [mag3110] using legacy suspend method
i2c-core: driver [mag3110] using legacy resume method
imx2-wdt imx2-wdt.0: IMX2+ Watchdog Timer enabled. timeout=60s (nowayout=1)
Bluetooth: Virtual HCI driver ver 1.3
Bluetooth: HCI UART driver ver 2.2
Bluetooth: HCIATH3K protocol initialized
Bluetooth: Generic Bluetooth USB driver ver 0.6
usbcore: registered new interface driver btusb
sdhci: Secure Digital Host Controller Interface driver
sdhci: Copyright(c) Pierre Ossman
mmc0: no vmmc regulator found
mmc0: SDHCI controller on platform [sdhci-esdhc-imx.0] using DMA
sdhci sdhci-esdhc-imx.2: no card-detect pin available!
mmc1: no vmmc regulator found
mmc1: SDHCI controller on platform [sdhci-esdhc-imx.2] using DMA
mxc_vdoa mxc_vdoa: i.MX Video Data Order Adapter(VDOA) driver probed
VPU initialized
mxc_asrc registered
Galcore version 4.6.9.6622
hub 2-1:1.0: USB hub found
Thermal calibration data is 0x5864e569
Thermal sensor with ratio = 183
hub 2-1:1.0: 4 ports detected
Anatop Thermal registered as thermal_zone0
anatop_thermal_probe: default cooling device is cpufreq!
usbcore: registered new interface driver usbhid
usbhid: USB HID core driver
usbcore: registered new interface driver snd-usb-audio
mxc_hdmi_soc mxc_hdmi_soc.0: MXC HDMI Audio
mxc_spdif mxc_spdif.0: MXC SPDIF Audio
mmc0: new high speed SDIO card at address 0001
imx_wm8731_init: success
asoc: wm8731-hifi <-> imx-ssi.1 mapping ok
asoc: mxc-spdif <-> imx-spdif-dai.0 mapping ok
asoc: mxc-hdmi-soc <-> imx-hdmi-soc-dai.0 mapping ok
ALSA device list:
  #0: wm8731-audio
  #1: imx-spdif
  #2: imx-hdmi-soc
NET: Registered protocol family 26
TCP cubic registered
NET: Registered protocol family 17
can: controller area network core (rev 20090105 abi 8)
NET: Registered protocol family 29
can: raw protocol (rev 20090105)
can: broadcast manager protocol (rev 20090105 t)
Bluetooth: RFCOMM TTY layer initialized
Bluetooth: RFCOMM socket layer initialized
Bluetooth: RFCOMM ver 1.11
Bluetooth: BNEP (Ethernet Emulation) ver 1.3
Bluetooth: BNEP filters: protocol multicast
Bluetooth: HIDP (Human Interface Emulation) ver 1.2
lib80211: common routines for IEEE802.11 drivers
VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4
Bus freq driver module loaded
Bus freq driver Enabled
mxc_dvfs_core_probe
DVFS driver module loaded
regulator_init_complete: vmmc: incomplete constraints, leaving on
rtc-em3027 3-0056: setting system clock to 2034-04-08 18:10:16 UTC (2028132616)
Waiting for root device /dev/mmcblk0p2...
mmc1: new high speed SDHC card at address 1234
mmcblk0: mmc1:1234 SA04G 3.63 GiB
 mmcblk0: p1 p2
EXT3-fs (mmcblk0p2): error: couldn't mount because of unsupported optional features (240)
usb 2-1.2: new low speed USB device number 3 using fsl-ehci
EXT2-fs (mmcblk0p2): error: couldn't mount because of unsupported optional features (244)
input: TypeMatrix.com USB Keyboard as /devices/platform/fsl-ehci.1/usb2/2-1/2-1.2/2-1.2:1.0/input/input0
generic-usb 0003:1E54:2030.0001: input,hidraw0: USB HID v1.10 Keyboard [TypeMatrix.com USB Keyboard] on usb-fsl-ehci.1-1.2/input0
input: TypeMatrix.com USB Keyboard as /devices/platform/fsl-ehci.1/usb2/2-1/2-1.2/2-1.2:1.1/input/input1
generic-usb 0003:1E54:2030.0002: input,hidraw1: USB HID v1.10 Device [TypeMatrix.com USB Keyboard] on usb-fsl-ehci.1-1.2/input1
usb 2-1.4: new low speed USB device number 4 using fsl-ehci
input: USB Optical Mouse as /devices/platform/fsl-ehci.1/usb2/2-1/2-1.4/2-1.4:1.0/input/input2
generic-usb 0003:04B3:310C.0003: input,hidraw2: USB HID v1.11 Mouse [USB Optical Mouse] on usb-fsl-ehci.1-1.4/input0
EXT4-fs (mmcblk0p2): recovery complete
EXT4-fs (mmcblk0p2): mounted filesystem with ordered data mode. Opts: (null)
VFS: Mounted root (ext4 filesystem) on device 179:2.
Freeing init memory: 196K
Mount failed for selinuxfs on /sys/fs/selinux:  No such file or directory
INIT: version 2.88 booting
[info] Using makefile-style concurrent boot in runlevel S.
[....] Starting the hotplug events dispatcher: udevdsystemd-udevd[1513]: starting version 204
. ok
[....] Synthesizing the initial hotplug events...Intel(R) Gigabit Ethernet Network Driver - version 4.1.2
Copyright (c) 2007-2012 Intel Corporation.
PCI: enabling device 0000:01:00.0 (0140 -> 0142)
igb: 0000:01:00.0: igb_check_options: VMDq option is not supported.
igb 0000:01:00.0: Failed to initialize MSI-X interrupts. Falling back to MSI interrupts.
igb 0000:01:00.0: Failed to initialize MSI interrupts.  Falling back to legacy interrupts.
done.
[....] Waiting for /dev to be fully popigb 0000:01:00.0: Intel(R) Gigabit Ethernet Network Connection
ulated...igb 0000:01:00.0: eth1: (PCIe:2.5GT/s:Width x1)
igb 0000:01:00.0: eth1: MAC: 00:01:c0:14:a8:b3
igb 0000:01:00.0: eth1: PBA No: FFFFFF-0FF
igb 0000:01:00.0: LRO is disabled
igb 0000:01:00.0: Using legacy interrupts. 1 rx queue(s), 1 tx queue(s)
Bluetooth: vendor=0x2df, device=0x911a, class=255, fn=2
mwifiex_sdio mmc0:0001:1: WLAN FW already running! Skip FW download
mwifiex_sdio mmc0:0001:1: WLAN FW is active
done.
[....] Setting preliminary keymap...done.
[....] Setting parameters of disc: (none). ok
[....] Activating swap...done.
EXT4-fs (mmcblk0p2): re-mounted. Opts: (null)
[....] Activating lvm and md swap...done.
[....] Checking file systems...fsck from util-linux 2.20.1
done.
[....] Cleaning up temporary files... /tmp. ok
[info] Loading kernel module fuse.
FATAL: Module fuse not found.
[info] Loading kernel module vivante.
[drm] Initialized drm 1.1.0 20060810
[drm] Initialized vivante 1.0.0 20120216 on minor 0
[....] Mounting local filesystems...done.
[....] Activating swapfile swap...done.
[....] Cleaning up temporary files.... ok
[....] Setting kernel variables ...done.
[....] Configuring network interfaces...done.
[....] Cleaning up temporary files.... ok
[....] Setting up ALSA...warning: 'alsactl -E HOME=/var/run/alsa restore' failed with error message 'No state is present for card wm8731audio
Found hardware: "wm8731-audio" "" "" "" ""
Hardware is initialized using a generic method
No state is present for card wm8731audio
No state is present for card imxspdif
Found hardware: "imx-spdif" "" "" "" ""
Hardware is initialized using a generic method
No state is present for card imxspdif'...amixer: Invalid command!
done.
[info] Setting console screen modes.
setterm: cannot (un)set powersave mode: Invalid argument
[....] Setting up console font and keymap...done.
[....] Setting up X socket directories... /tmp/.X11-unix /tmp/.ICE-unix. ok
INIT: Entering runlevel: 2
[info] Using makefile-style concurrent boot in runlevel 2.
[....] Starting enhanced syslogd: rsyslogd. ok
udhcpd: Disabled. Edit /etc/default/udhcpd to enable it.
[....] Starting periodic command scheduler: cron. ok
[....] Starting NTP server: ntpd. ok
[....] Starting system message bus: dbus. ok
saned disabled; edit /etc/default/saned
[....] Starting Light Display Manager: lightdm. ok
[....] Starting OpenBSD Secure Shell server: sshd. ok
vgaarb: this pci device is not a vga device
vgaarb: this pci device is not a vga device

Debian GNU/Linux jessie/sid debian-imx6 ttymxc3

debian-imx6 login