Boot message

U-Boot 2013.07-00787-g36ed10c (Mar 24 2015 - 16:02:12)

CPU:   Freescale i.MX6DL rev1.3 at 792 MHz
Reset cause: POR
Board: Ka-Ro TX6U-8030
I2C:   ready
DRAM:  1 GiB
VDDCORE set to 1350mV
VDDSOC  set to 1350mV
NAND:  128 MiB
MMC:   FSL_SDHC: 0, FSL_SDHC: 1
IPU HW Rev: 4
Temperature:   41 C, calibration data 0x5854f569
CPU clock set to 792.000 MHz
Baseboard: stk5-v3
MAC addr from fuse: 00:0c:c6:7d:23:07
Net:   FEC
Hit any key to stop autoboot:  0
4453664 bytes read in 306 ms (13.9 MiB/s)
## Booting kernel from Legacy Image at 18000000 ...
   Image Name:   Linux-4.3.0
   Image Type:   ARM Linux Kernel Image (uncompressed)
   Data Size:    4453600 Bytes = 4.2 MiB
   Load Address: 10008000
   Entry Point:  10008000
   Verifying Checksum ... OK
## Flattened Device Tree blob at 11000000
   Booting using the fdt blob at 0x11000000
   Loading Kernel Image ... OK
   Loading Device Tree to 4ef3e000, end 4ef4abc5 ... OK

Starting kernel ...

Disabling LCD
Uncompressing Linux... done, booting the kernel.
Booting Linux on physical CPU 0x0
Linux version 4.3.0 (angelo@eeo-v-dev-lx-1204) (gcc version 4.7.2 (GCC) ) #3 SMP PREEMPT Tue Dec 8 17:02:36 CET 2015
CPU: ARMv7 Processor [412fc09a] revision 10 (ARMv7), cr=10c5387d
CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
Machine model: Ka-Ro electronics TX6U-801x/-803x Module
cma: Reserved 320 MiB at 0x3ac00000
Memory policy: Data cache writealloc
On node 0 totalpages: 262144
free_area_init_node: node 0, pgdat 8085f580, node_mem_map bf757000
  Normal zone: 2048 pages used for memmap
  Normal zone: 0 pages reserved
  Normal zone: 262144 pages, LIFO batch:31
PERCPU: Embedded 12 pages/cpu @bf71f000 s18176 r8192 d22784 u49152
pcpu-alloc: s18176 r8192 d22784 u49152 alloc=12*4096
pcpu-alloc: [0] 0 [0] 1
Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 260096
Kernel command line: init=/linuxrc console=ttymxc0,115200 ro debug panic=1 root=/dev/mmcblk0p1 rootwait mtdparts=gpmi-nand:1024k@0x20000(u-boot),384k(env),6m(linux),32m(rootfs),89600k(userfs),512k@0x7f00000(dtb),512k@0x7f80000(bbt)ro
PID hash table entries: 4096 (order: 2, 16384 bytes)
Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
Memory: 701984K/1048576K available (5965K kernel code, 177K rwdata, 2124K rodata, 276K init, 441K bss, 18912K reserved, 327680K cma-reserved, 0K highmem)
Virtual kernel memory layout:
    vector  : 0xffff0000 - 0xffff1000   (   4 kB)
    fixmap  : 0xffc00000 - 0xfff00000   (3072 kB)
    vmalloc : 0xc0800000 - 0xff000000   (1000 MB)
    lowmem  : 0x80000000 - 0xc0000000   (1024 MB)
    pkmap   : 0x7fe00000 - 0x80000000   (   2 MB)
    modules : 0x7f000000 - 0x7fe00000   (  14 MB)
      .text : 0x80008000 - 0x807ee838   (8091 kB)
      .init : 0x807ef000 - 0x80834000   ( 276 kB)
      .data : 0x80834000 - 0x808605a0   ( 178 kB)
       .bss : 0x808605a0 - 0x808cea94   ( 442 kB)
SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
Preemptible hierarchical RCU implementation.
        Build-time adjustment of leaf fanout to 32.
        RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=2.
RCU: Adjusting geometry for rcu_fanout_leaf=32, nr_cpu_ids=2
NR_IRQS:16 nr_irqs:16 16
------------[ cut here ]------------
WARNING: CPU: 0 PID: 0 at arch/arm/mach-imx/gpc.c:286 imx_gpc_check_dt+0x38/0x84()
Modules linked in:
CPU: 0 PID: 0 Comm: swapper/0 Not tainted 4.3.0 #3
Hardware name: Freescale i.MX6 Quad/DualLite (Device Tree)
[<800165d8>] (unwind_backtrace) from [<800123ac>] (show_stack+0x10/0x14)
[<800123ac>] (show_stack) from [<8027285c>] (dump_stack+0x80/0xcc)
[<8027285c>] (dump_stack) from [<8002187c>] (warn_slowpath_common+0x74/0xb0)
[<8002187c>] (warn_slowpath_common) from [<800218d4>] (warn_slowpath_null+0x1c/0x24)
[<800218d4>] (warn_slowpath_null) from [<807f6a78>] (imx_gpc_check_dt+0x38/0x84)
[<807f6a78>] (imx_gpc_check_dt) from [<807f704c>] (imx6q_init_irq+0x8/0x28)
[<807f704c>] (imx6q_init_irq) from [<807f10a8>] (init_IRQ+0x28/0x80)
[<807f10a8>] (init_IRQ) from [<807efb10>] (start_kernel+0x24c/0x36c)
[<807efb10>] (start_kernel) from [<1000807c>] (0x1000807c)
---[ end trace cb88537fdc8fa200 ]---
Outdated DT detected, suspend/resume will NOT work
L2C-310 erratum 769419 enabled
L2C-310 enabling early BRESP for Cortex-A9
L2C-310 full line of zeros enabled for Cortex-A9
L2C-310 ID prefetch enabled, offset 1 lines
L2C-310 dynamic clock gating enabled, standby mode enabled
L2C-310 cache controller enabled, 16 ways, 512 kB
L2C-310: CACHE_ID 0x410000c8, AUX_CTRL 0x76050001
Switching to timer-based delay loop, resolution 15ns
sched_clock: 32 bits at 66MHz, resolution 15ns, wraps every 32537631224ns
clocksource: mxc_timer1: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 28958491609 ns
Console: colour dummy device 80x30
Calibrating delay loop (skipped), value calculated using timer frequency.. 132.00 BogoMIPS (lpj=660000)
pid_max: default: 32768 minimum: 301
Mount-cache hash table entries: 2048 (order: 1, 8192 bytes)
Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes)
CPU: Testing write buffer coherency: ok
CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
Setting up static identity map for 0x100082c0 - 0x10008318
CPU1: thread -1, cpu 1, socket 0, mpidr 80000001
Brought up 2 CPUs
SMP: Total of 2 processors activated (264.00 BogoMIPS).
CPU: All CPU(s) started in SVC mode.
devtmpfs: initialized
VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4
clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
pinctrl core: initialized pinctrl subsystem
NET: Registered protocol family 16
DMA: preallocated 256 KiB pool for atomic coherent allocations
cpuidle: using governor ladder
cpuidle: using governor menu
CPU identified as i.MX6DL, silicon rev 1.3
imx6dl-pinctrl 20e0000.iomuxc: initialized IMX pinctrl driver
mxs-dma 110000.dma-apbh: initialized
imx6dl-pinctrl 20e0000.iomuxc: pin MX6DL_PAD_EIM_EB3 already requested by 20e0000.iomuxc; cannot claim for regulators:regulator@5
imx6dl-pinctrl 20e0000.iomuxc: pin-116 (regulators:regulator@5) status -22
imx6dl-pinctrl 20e0000.iomuxc: could not request pin 116 (MX6DL_PAD_EIM_EB3) from group lcd1-pwrgrp  on device 20e0000.iomuxc
reg-fixed-voltage regulators:regulator@5: Error applying setting, reverse things back
SCSI subsystem initialized
libata version 3.00 loaded.
i2c i2c-0: IMX I2C adapter registered
i2c i2c-0: can't use DMA
i2c i2c-2: IMX I2C adapter registered
i2c i2c-2: can't use DMA
Linux video capture interface: v2.00
pps_core: LinuxPPS API ver. 1 registered
pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <[email protected]>
PTP clock support registered
Advanced Linux Sound Architecture Driver Initialized.
clocksource: Switched to clocksource mxc_timer1
NET: Registered protocol family 2
TCP established hash table entries: 8192 (order: 3, 32768 bytes)
TCP bind hash table entries: 8192 (order: 4, 65536 bytes)
TCP: Hash tables configured (established 8192 bind 8192)
UDP hash table entries: 512 (order: 2, 16384 bytes)
UDP-Lite hash table entries: 512 (order: 2, 16384 bytes)
NET: Registered protocol family 1
RPC: Registered named UNIX socket transport module.
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
RPC: Registered tcp NFSv4.1 backchannel transport module.
PCI: CLS 0 bytes, default 64
futex hash table entries: 512 (order: 3, 32768 bytes)
NFS: Registering the id_resolver key type
Key type id_resolver registered
Key type id_legacy registered
fuse init (API version 7.23)
io scheduler noop registered
io scheduler deadline registered
io scheduler cfq registered (default)
imx-weim 21b8000.weim: Driver registered.
pwm-backlight backlight: unable to request PWM, trying legacy API
imx-sdma 20ec000.sdma: no event needs to be remapped
imx-sdma 20ec000.sdma: Direct firmware load for imx/sdma/sdma-imx6q.bin failed with error -2
imx-sdma 20ec000.sdma: external firmware not found, using ROM firmware
imx-sdma 20ec000.sdma: initialized
2020000.serial: ttymxc0 at MMIO 0x2020000 (irq = 23, base_baud = 5000000) is a IMX
console [ttymxc0] enabled
21e8000.serial: ttymxc1 at MMIO 0x21e8000 (irq = 296, base_baud = 5000000) is a IMX
21ec000.serial: ttymxc2 at MMIO 0x21ec000 (irq = 297, base_baud = 5000000) is a IMX
[drm] Initialized drm 1.1.0 20060810
brd: module loaded
loop: module loaded
nand: device found, Manufacturer ID: 0xec, Chip ID: 0xf1
nand: Samsung NAND 128MiB 3,3V 8-bit
nand: 128 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64
Bad block table found at page 65472, version 0x01
Bad block table found at page 65408, version 0x01
7 cmdlinepart partitions found on MTD device gpmi-nand
Creating 7 MTD partitions on "gpmi-nand":
0x000000020000-0x000000120000 : "u-boot"
0x000000120000-0x000000180000 : "env"
0x000000180000-0x000000780000 : "linux"
0x000000780000-0x000002780000 : "rootfs"
0x000002780000-0x000007f00000 : "userfs"
0x000007f00000-0x000007f80000 : "dtb"
0x000007f80000-0x000008000000 : "bbt"
gpmi-nand 112000.gpmi-nand: driver registered.
spidev spi0.0: buggy DT: spidev listed directly in DT
------------[ cut here ]------------
WARNING: CPU: 0 PID: 1 at drivers/spi/spidev.c:719 spidev_probe+0x174/0x1b0()
Modules linked in:
CPU: 0 PID: 1 Comm: swapper/0 Tainted: G        W       4.3.0 #3
Hardware name: Freescale i.MX6 Quad/DualLite (Device Tree)
[<800165d8>] (unwind_backtrace) from [<800123ac>] (show_stack+0x10/0x14)
[<800123ac>] (show_stack) from [<8027285c>] (dump_stack+0x80/0xcc)
[<8027285c>] (dump_stack) from [<8002187c>] (warn_slowpath_common+0x74/0xb0)
[<8002187c>] (warn_slowpath_common) from [<800218d4>] (warn_slowpath_null+0x1c/0x24)
[<800218d4>] (warn_slowpath_null) from [<803b09f0>] (spidev_probe+0x174/0x1b0)
[<803b09f0>] (spidev_probe) from [<803aed90>] (spi_drv_probe+0x5c/0x74)
[<803aed90>] (spi_drv_probe) from [<80336c2c>] (driver_probe_device+0x1e0/0x2a0)
[<80336c2c>] (driver_probe_device) from [<803352e0>] (bus_for_each_drv+0x44/0x8c)
[<803352e0>] (bus_for_each_drv) from [<803369c0>] (__device_attach+0xa0/0x104)
[<803369c0>] (__device_attach) from [<8033613c>] (bus_probe_device+0x84/0x8c)
[<8033613c>] (bus_probe_device) from [<80334690>] (device_add+0x33c/0x528)
[<80334690>] (device_add) from [<803aec08>] (spi_add_device+0x88/0x130)
[<803aec08>] (spi_add_device) from [<803b03f0>] (spi_register_master+0x544/0x710)
[<803b03f0>] (spi_register_master) from [<803b179c>] (spi_bitbang_start+0x94/0x10c)
[<803b179c>] (spi_bitbang_start) from [<803b2aac>] (spi_imx_probe+0x3ac/0x694)
[<803b2aac>] (spi_imx_probe) from [<80338110>] (platform_drv_probe+0x48/0xa4)
[<80338110>] (platform_drv_probe) from [<80336c2c>] (driver_probe_device+0x1e0/0x2a0)
[<80336c2c>] (driver_probe_device) from [<80336d78>] (__driver_attach+0x8c/0x90)
[<80336d78>] (__driver_attach) from [<8033537c>] (bus_for_each_dev+0x54/0x88)
[<8033537c>] (bus_for_each_dev) from [<8033631c>] (bus_add_driver+0xe4/0x1f0)
[<8033631c>] (bus_add_driver) from [<80337540>] (driver_register+0x78/0xf4)
[<80337540>] (driver_register) from [<80009744>] (do_one_initcall+0x80/0x1d0)
[<80009744>] (do_one_initcall) from [<807efd4c>] (kernel_init_freeable+0x11c/0x1e8)
[<807efd4c>] (kernel_init_freeable) from [<805a48f4>] (kernel_init+0x8/0xe4)
[<805a48f4>] (kernel_init) from [<8000f878>] (ret_from_fork+0x14/0x3c)
---[ end trace cb88537fdc8fa201 ]---
spidev spi0.1: buggy DT: spidev listed directly in DT
------------[ cut here ]------------
WARNING: CPU: 1 PID: 1 at drivers/spi/spidev.c:719 spidev_probe+0x174/0x1b0()
Modules linked in:
CPU: 1 PID: 1 Comm: swapper/0 Tainted: G        W       4.3.0 #3
Hardware name: Freescale i.MX6 Quad/DualLite (Device Tree)
[<800165d8>] (unwind_backtrace) from [<800123ac>] (show_stack+0x10/0x14)
[<800123ac>] (show_stack) from [<8027285c>] (dump_stack+0x80/0xcc)
[<8027285c>] (dump_stack) from [<8002187c>] (warn_slowpath_common+0x74/0xb0)
[<8002187c>] (warn_slowpath_common) from [<800218d4>] (warn_slowpath_null+0x1c/0x24)
[<800218d4>] (warn_slowpath_null) from [<803b09f0>] (spidev_probe+0x174/0x1b0)
[<803b09f0>] (spidev_probe) from [<803aed90>] (spi_drv_probe+0x5c/0x74)
[<803aed90>] (spi_drv_probe) from [<80336c2c>] (driver_probe_device+0x1e0/0x2a0)
[<80336c2c>] (driver_probe_device) from [<803352e0>] (bus_for_each_drv+0x44/0x8c)
[<803352e0>] (bus_for_each_drv) from [<803369c0>] (__device_attach+0xa0/0x104)
[<803369c0>] (__device_attach) from [<8033613c>] (bus_probe_device+0x84/0x8c)
[<8033613c>] (bus_probe_device) from [<80334690>] (device_add+0x33c/0x528)
[<80334690>] (device_add) from [<803aec08>] (spi_add_device+0x88/0x130)
[<803aec08>] (spi_add_device) from [<803b03f0>] (spi_register_master+0x544/0x710)
[<803b03f0>] (spi_register_master) from [<803b179c>] (spi_bitbang_start+0x94/0x10c)
[<803b179c>] (spi_bitbang_start) from [<803b2aac>] (spi_imx_probe+0x3ac/0x694)
[<803b2aac>] (spi_imx_probe) from [<80338110>] (platform_drv_probe+0x48/0xa4)
[<80338110>] (platform_drv_probe) from [<80336c2c>] (driver_probe_device+0x1e0/0x2a0)
[<80336c2c>] (driver_probe_device) from [<80336d78>] (__driver_attach+0x8c/0x90)
[<80336d78>] (__driver_attach) from [<8033537c>] (bus_for_each_dev+0x54/0x88)
[<8033537c>] (bus_for_each_dev) from [<8033631c>] (bus_add_driver+0xe4/0x1f0)
[<8033631c>] (bus_add_driver) from [<80337540>] (driver_register+0x78/0xf4)
[<80337540>] (driver_register) from [<80009744>] (do_one_initcall+0x80/0x1d0)
[<80009744>] (do_one_initcall) from [<807efd4c>] (kernel_init_freeable+0x11c/0x1e8)
[<807efd4c>] (kernel_init_freeable) from [<805a48f4>] (kernel_init+0x8/0xe4)
[<805a48f4>] (kernel_init) from [<8000f878>] (ret_from_fork+0x14/0x3c)
---[ end trace cb88537fdc8fa202 ]---
spi_imx 2008000.ecspi: probed
vcan: Virtual CAN interface driver
CAN device driver interface
2090000.flexcan supply xceiver not found, using dummy regulator
flexcan 2090000.flexcan: device registered (reg_base=c09f0000, irq=30)
2094000.flexcan supply xceiver not found, using dummy regulator
flexcan 2094000.flexcan: device registered (reg_base=c09f8000, irq=31)
pps pps0: new PPS source ptp0
libphy: fec_enet_mii_bus: probed
fec 2188000.ethernet eth0: registered PHC device 0
imx6dl-pinctrl 20e0000.iomuxc: pin MX6DL_PAD_GPIO_9 already requested by 20e0000.iomuxc; cannot claim for 20b8000.kpp
imx6dl-pinctrl 20e0000.iomuxc: pin-144 (20b8000.kpp) status -22
imx6dl-pinctrl 20e0000.iomuxc: could not request pin 144 (MX6DL_PAD_GPIO_9) from group kppgrp  on device 20e0000.iomuxc
imx-keypad 20b8000.kpp: Error applying setting, reverse things back
input: 20b8000.kpp as /devices/soc0/soc/2000000.aips-bus/20b8000.kpp/input/input0
rtc-ds1307 0-0068: rtc core: registered ds1339 as rtc0
snvs_rtc 20cc034.snvs-rtc-lp: snvs rtc: you use old dts file, please update it
snvs_rtc 20cc034.snvs-rtc-lp: rtc core: registered 20cc034.snvs-rtc-lp as rtc1
i2c /dev entries driver
imx2-wdt 20bc000.wdog: timeout 60 sec (nowayout=0)
sdhci: Secure Digital Host Controller Interface driver
sdhci: Copyright(c) Pierre Ossman
sdhci-pltfm: SDHCI platform and OF driver helper
/soc/aips-bus@02100000/usdhc@02190000: voltage-ranges unspecified
sdhci-esdhc-imx 2190000.usdhc: Got CD GPIO
sdhci-esdhc-imx 2190000.usdhc: No vmmc regulator found
sdhci-esdhc-imx 2190000.usdhc: No vqmmc regulator found
mmc0: SDHCI controller on 2190000.usdhc [2190000.usdhc] using ADMA
/soc/aips-bus@02100000/usdhc@02194000: voltage-ranges unspecified
sdhci-esdhc-imx 2194000.usdhc: Got CD GPIO
sdhci-esdhc-imx 2194000.usdhc: No vmmc regulator found
sdhci-esdhc-imx 2194000.usdhc: No vqmmc regulator found
mmc1: SDHCI controller on 2194000.usdhc [2194000.usdhc] using ADMA
sgtl5000 2-000a: sgtl5000 revision 0x11
sgtl5000 2-000a: Using internal LDO instead of VDDD
imx-sgtl5000 sound: sgtl5000 <-> 2028000.ssi mapping ok
NET: Registered protocol family 17
can: controller area network core (rev 20120528 abi 9)
NET: Registered protocol family 29
can: raw protocol (rev 20120528)
can: broadcast manager protocol (rev 20120528 t)
Key type dns_resolver registered
Registering SWP/SWPB emulation handler
input: gpio-keys as /devices/soc0/gpio-keys/input/input1
rtc-ds1307 0-0068: setting system clock to 2000-01-01 18:24:06 UTC (946751046)
usbh1_vbus: disabling
ALSA device list:
  #0: sgtl5000-audio
Waiting for root device /dev/mmcblk0p1...
random: nonblocking pool is initialized