DRAM: 480MB
Number of U-Boot devices: 1
U-Boot env: loaderdev not set, will probe all devices.
Found U-Boot device: disk
  Probing all disk devices...
  Checking unit=0 slice=<auto> partition=<auto>... good.
Loading /boot/defaults/loader.conf
/boot/kernel/kernel data=0x4c71a4+0xace5c syms=[0x4+0x87670+0x4+0x51bae]

Hit [Enter] to boot immediately, or any other key for command prompt.
Booting [/boot/kernel/kernel]...
Using DTB provided by U-Boot at address 0x0x100.
Kernel entry at 0x100100...
Kernel args: (null)
KDB: debugger backends: ddb
KDB: current backend: ddb
Copyright (c) 1992-2014 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
	The Regents of the University of California. All rights reserved.
FreeBSD is a registered trademark of The FreeBSD Foundation.
FreeBSD 10.1-PRERELEASE #0 7f2261a(master)-dirty: Tue Sep  9 18:27:08 BRT 2014
    root@danilo:/home/danilo/Mestrado/Sources/crochet-freebsd/work/obj/arm.armv6/home/danilo/Mestrado/Sources/freebsd/sys/RADNET arm
FreeBSD clang version 3.4.1 (tags/RELEASE_34/dot1-final 208032) 20140512
VT: init without driver.
CPU: ARM1176JZ-S rev 7 (ARM11J core)
 Supported features: ARM_ISA THUMB2 JAZELLE ARMv4 Security_Ext
 WB enabled LABT branch prediction enabled
  16KB/32B 4-way instruction cache
  16KB/32B 4-way write-back-locking-C data cache
real memory  = 536866816 (511 MB)
avail memory = 483446784 (461 MB)
random device not loaded; using insecure entropy
random: <Software, Yarrow> initialized
kbd0 at kbdmux0
ofwbus0: <Open Firmware Device Tree>
simplebus0: <Flattened device tree simple bus> mem 0x20000000-0x20ffffff on ofwbus0
intc0: <BCM2835 Interrupt Controller> mem 0xb200-0xb3ff on simplebus0
systimer0: <BCM2835 System Timer> mem 0x3000-0x3fff irq 8,9,10,11 on simplebus0
Event timer "BCM2835 Event Timer 3" frequency 1000000 Hz quality 1000
Timecounter "BCM2835 Timecounter" frequency 1000000 Hz quality 1000
bcmwd0: <BCM2708/2835 Watchdog> mem 0x10001c-0x100027 on simplebus0
gpio0: <BCM2708/2835 GPIO controller> mem 0x200000-0x2000af irq 57,59,58,60 on simplebus0
gpio0: read-only pins: 46,47,48,49,50,51,52,53.
gpio0: reserved pins: 48,49,50,51,52,53.
gpioc0: <GPIO controller> on gpio0
gpiobus0: <OFW GPIO bus> on gpio0
gpioled0: <GPIO led> at pin(s) 16 on gpiobus0
iichb0: <BCM2708/2835 BSC controller> mem 0x205000-0x20501f irq 61 on simplebus0
iicbus0: <OFW I2C bus> on iichb0
iic0: <I2C generic I/O> on iicbus0
iichb1: <BCM2708/2835 BSC controller> mem 0x804000-0x80401f irq 61 on simplebus0
iicbus1: <OFW I2C bus> on iichb1
iic1: <I2C generic I/O> on iicbus1
spi0: <BCM2708/2835 SPI controller> mem 0x204000-0x20401f irq 62 on simplebus0
spibus0: <OFW SPI bus> on spi0
bcm_dma0: <BCM2835 DMA Controller> mem 0x7000-0x7fff,0xe05000-0xe05fff irq 24,25,26,27,28,29,30,31,32,33,34,35,36 on simplebus0
mbox0: <BCM2835 VideoCore Mailbox> mem 0xb880-0xb8bf irq 1 on simplebus0
sdhci_bcm0: <Broadcom 2708 SDHCI controller> mem 0x300000-0x3000ff irq 70 on simplebus0
mmc0: <MMC/SD bus> on sdhci_bcm0
uart0: <PrimeCell UART (PL011)> mem 0x201000-0x201fff irq 65 on simplebus0
uart0: console (115200,n,8,1)
dwcotg0: <DWC OTG 2.0 integrated USB controller> mem 0x980000-0x99ffff irq 17 on simplebus0
usbus0 on dwcotg0
fb0: <BCM2835 VT framebuffer driver> on ofwbus0
simplebus1: <Flattened device tree simple bus> on ofwbus0
simplebus1: could not get ranges
device_attach: simplebus1 attach returned 6
Timecounters tick every 10.000 msec
RADNET pr_init running
RADNET Initializing...
usbus0: 480Mbps High Speed USB v2.0
ugen0.1: <DWCOTG> at usbus0
uhub0: <DWCOTG OTG Root HUB, class 9/0, rev 2.00/1.00, addr 1> on usbus0
mmcsd0: 4GB <SDHC SA04G 1.0 SN 1A93CC12 MFG 07/2012 by 2 TM> at mmc0 50.0MHz/4bit/65535-block
fb0: 656x416(0x0@0,0) 16bpp
fb0: pitch 1312, base 0x5e006000, screen_size 545792
fbd0 on fb0
VT: initialize with new VT driver "fb".
device_attach: fbd0 attach returned 6
fb0: Failed to attach fbd device
uhub0: 1 port with 1 removable, self powered
ugen0.2: <vendor 0x0424> at usbus0
uhub1: <vendor 0x0424 product 0x9514, class 9/0, rev 2.00/2.00, addr 2> on usbus0
uhub1: MTT enabled
uhub1: 5 ports with 4 removable, self powered
random: unblocking device.
ugen0.3: <vendor 0x0424> at usbus0
smsc0: <vendor 0x0424 product 0xec00, rev 2.00/2.00, addr 3> on usbus0
smsc0: chip 0xec00, rev. 0002
miibus0: <MII bus> on smsc0
ukphy0: <Generic IEEE 802.3u media interface> PHY 1 on miibus0
ukphy0:  none, 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
ue0: <USB Ethernet> on smsc0
ue0: Ethernet address: b8:27:eb:60:d9:9b
run_interrupt_driven_hooks: still waiting after 60 seconds for bcm_fb_init
run_interrupt_driven_hooks: still waiting after 120 seconds for bcm_fb_init
run_interrupt_driven_hooks: still waiting after 180 seconds for bcm_fb_init
run_interrupt_driven_hooks: still waiting after 240 seconds for bcm_fb_init
run_interrupt_driven_hooks: still waiting after 300 seconds for bcm_fb_init
panic: run_interrupt_driven_config_hooks: waited too long
KDB: enter: panic
[ thread pid 0 tid 100000 ]
Stopped at      $d:     ldrb    r15, [r15, r15, ror r15]!
db> bt
Tracing pid 0 tid 100000 td 0xc0666620
db_trace_self() at db_trace_self
         pc = 0xc04959b0  lr = 0xc01301d0 (db_stack_trace+0xf4)
         sp = 0xc0762aa8  fp = 0xc0762ac0
        r10 = 0xc06656b0
db_stack_trace() at db_stack_trace+0xf4
         pc = 0xc01301d0  lr = 0xc012fb40 (db_command+0x270)
         sp = 0xc0762ac8  fp = 0xc0762b68
         r4 = 0x00000000  r5 = 0x00000000
         r6 = 0x00000000
db_command() at db_command+0x270
         pc = 0xc012fb40  lr = 0xc012f8a4 (db_command_loop+0x60)
         sp = 0xc0762b70  fp = 0xc0762b80
         r4 = 0xc04d5971  r5 = 0xc04f0b9b
         r6 = 0xc066569c  r7 = 0xc0590340
         r8 = 0xc065bbb4  r9 = 0xc065bbb0
        r10 = 0xc0762d50
db_command_loop() at db_command_loop+0x60
         pc = 0xc012f8a4  lr = 0xc013226c (db_trap+0xd8)
         sp = 0xc0762b88  fp = 0xc0762ca8
         r4 = 0x00000000  r5 = 0xc06656a8
         r6 = 0xc065bbe0
db_trap() at db_trap+0xd8
         pc = 0xc013226c  lr = 0xc0290130 (kdb_trap+0xbc)
         sp = 0xc0762cb0  fp = 0xc0762cd0
         r4 = 0x00000000  r5 = 0x00000001
         r6 = 0xc065bbe0  r7 = 0xc0590340
kdb_trap() at kdb_trap+0xbc
         pc = 0xc0290130  lr = 0xc04a9200 (undefinedinstruction+0x298)
         sp = 0xc0762cd8  fp = 0xc0762d48
         r4 = 0x00000000  r5 = 0x00000000
         r6 = 0xc04a8eb8  r7 = 0xe7ffffff
         r8 = 0xc0666620  r9 = 0xc028fa00
        r10 = 0xc0762d50
undefinedinstruction() at undefinedinstruction+0x298
         pc = 0xc04a9200  lr = 0xc049752c (exception_exit)
         sp = 0xc0762d50  fp = 0xc0762da8
         r4 = 0xc04f0bf5  r5 = 0xc0762dfc
         r6 = 0xc04f33e8  r7 = 0xc064e100
         r8 = 0xc0666620  r9 = 0xc0667100
        r10 = 0xc064df60
exception_exit() at exception_exit
         pc = 0xc049752c  lr = 0xc028f9f4 (kdb_enter+0x40)
         sp = 0xc0762da0  fp = 0xc0762da8
         r0 = 0xc065bbc4  r1 = 0x00000000
         r2 = 0xc04f46f3  r3 = 0x000000ab
         r4 = 0xc04f0bf5  r5 = 0xc0762dfc
         r6 = 0xc04f33e8  r7 = 0xc064e100
         r8 = 0xc0666620  r9 = 0xc0667100
        r10 = 0xc064df60 r12 = 0x00000000
$a() at $a
         pc = 0xc028fa04  lr = 0xc025874c (vpanic+0xb4)
         sp = 0xc0762db0  fp = 0xc0762dd0
         r4 = 0x00000100
vpanic() at vpanic+0xb4
         pc = 0xc025874c  lr = 0xc0258688 ($d)
         sp = 0xc0762dd8  fp = 0xc0762df0
         r4 = 0xc064e000  r5 = 0xc04f33e8
         r6 = 0xc0762dfc  r7 = 0xc064df60
         r8 = 0xc065b9a0  r9 = 0xc065b9b8
        r10 = 0x00000000
$d() at $d
         pc = 0xc0258688  lr = 0xc0282954 (boot_run_interrupt_driven_config_hooks+0x10c)
         sp = 0xc0762e08  fp = 0xc0762e88
         r4 = 0x0000003b  r5 = 0xc0762e2c
         r6 = 0xc05b01f0  r7 = 0xc04f336a
boot_run_interrupt_driven_config_hooks() at boot_run_interrupt_driven_config_hooks+0x10c
         pc = 0xc0282954  lr = 0xc0207370 (mi_startup+0x11c)
         sp = 0xc0762e90  fp = 0xc0762ea8
         r4 = 0x00000001  r5 = 0xc0666618
         r6 = 0x00000000  r7 = 0xc052243c
         r8 = 0xc0666e24  r9 = 0xc0666e20
        r10 = 0x00023bcb
mi_startup() at mi_startup+0x11c
         pc = 0xc0207370  lr = 0xc0100238 (virt_done+0x44)
         sp = 0xc0762eb0  fp = 0x00000000
         r4 = 0xc0100268  r5 = 0xc0670000
         r6 = 0x02049a80  r7 = 0x0010014c
         r8 = 0x00000000  r9 = 0xc0753000
virt_done() at virt_done+0x44
         pc = 0xc0100238  lr = 0xc0100238 (virt_done+0x44)
         sp = 0xc0762eb0  fp = 0x00000000
Unable to unwind further