uImage2_dmesg

<6>Initializing cgroup subsys cpu
<5>Linux version 3.0.8+ (unknown@unknown-virtual-machine) (gcc version 4.4.3 (GCC) ) #1103 PREEMPT Thu Oct 18 14:14:01 PDT 2012
<4>CPU: ARMv7 Processor [413fc082] revision 2 (ARMv7), cr=10c53c7d
<4>CPU: VIPT nonaliasing data cache, VIPT aliasing instruction cache
<4>Machine: encore
<4>Ignoring unrecognised tag 0x54410008
<6>Reserving 10485760 bytes SDRAM for VRAM
<4>Memory policy: ECC disabled, Data cache writeback
<6>OMAP3630 ES1.1 (l2cache iva sgx neon isp 192mhz_clk )
<6>SRAM: Mapped pa 0x40200000 to va 0xfe400000 size: 0x10000
<7>On node 0 totalpages: 118528
<7>free_area_init_node: node 0, pgdat c07aaa54, node_mem_map c093f000
<7>  Normal zone: 1024 pages used for memmap
<7>  Normal zone: 0 pages reserved
<7>  Normal zone: 117504 pages, LIFO batch:31
<6>Clocking rate (Crystal/Core/MPU): 26.0/332/600 MHz
<6>Reprogramming SDRC clock to 332000000 Hz
<7>pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
<7>pcpu-alloc: [0] 0
<4>Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 117504
<5>Kernel command line: console=ttyO0,115200n8 rw init=/init videoout=omap24xxvout omap_vout_mod.video1_numbuffers=6 omap_vout_mod.vid1_static_vrfb_alloc=y omap_vout_mod.video2_numbuffers=6 omap_vout_mod.vid2_static_vrfb_alloc=y omapfb.vram=0:8M no_console_suspend backlighttype=1476AY
<6>PID hash table entries: 2048 (order: 1, 8192 bytes)
<6>Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
<6>Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
<6>Memory: 462MB 1MB = 463MB total
<5>Memory: 459896k/459896k available, 64392k reserved, 0K highmem
<5>Virtual kernel memory layout:
<5>    vector  : 0xffff0000 - 0xffff1000   (   4 kB)
<5>    fixmap  : 0xfff00000 - 0xfffe0000   ( 896 kB)
<5>    DMA     : 0xffc00000 - 0xffe00000   (   2 MB)
<5>    vmalloc : 0xe0800000 - 0xf8000000   ( 376 MB)
<5>    lowmem  : 0xc0000000 - 0xe0000000   ( 512 MB)
<5>    pkmap   : 0xbfe00000 - 0xc0000000   (   2 MB)
<5>    modules : 0xbf000000 - 0xbfe00000   (  14 MB)
<5>      .init : 0xc0008000 - 0xc003c000   ( 208 kB)
<5>      .text : 0xc003c000 - 0xc0745ed0   (7208 kB)
<5>      .data : 0xc0746000 - 0xc07ac648   ( 410 kB)
<5>       .bss : 0xc07ac66c - 0xc093e620   (1608 kB)
<6>SLUB: Genslabs=11, HWalign=64, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
<6>NR_IRQS:410
<6>IRQ: Found an INTC at 0xfa200000 (revision 4.0) with 96 interrupts
<6>Total of 96 interrupts on 1 active controller
<6>OMAP clockevent source: GPTIMER1 at 32768 Hz
<6>sched_clock: 32 bits at 32kHz, resolution 30517ns, wraps every 131071999ms
<6>Console: colour dummy device 80x30
<6>Calibrating delay loop... 597.64 BogoMIPS (lpj=2334720)
<6>pid_max: default: 32768 minimum: 301
<6>Mount-cache hash table entries: 512
<6>Initializing cgroup subsys debug
<6>Initializing cgroup subsys cpuacct
<6>Initializing cgroup subsys freezer
<6>Initializing cgroup subsys bfqio
<6>CPU: Testing write buffer coherency: ok
<4>omap_hwmod: _populate_mpu_rt_base found no _mpu_rt_va for l4_core
<4>omap_hwmod: _populate_mpu_rt_base found no _mpu_rt_va for l4_per
<4>omap_hwmod: _populate_mpu_rt_base found no _mpu_rt_va for l4_wkup
<4>omap_hwmod: _populate_mpu_rt_base found no _mpu_rt_va for usbhs_ohci
<4>omap_hwmod: _populate_mpu_rt_base found no _mpu_rt_va for usbhs_ehci
<6>print_constraints: dummy:
<6>NET: Registered protocol family 16
<6>GPMC revision 5.0
<6>OMAP GPIO hardware version 2.5
<6>omap_mux_init: Add partition: #1: core, flags: 0
<4>board-3621_evt1a.c: kxtf9_dev_init ...
<4>board-3621_evt1a.c: kxtf9_dev_init > Init kxtf9 irq pin 113 !
<4>board-3621_evt1a.c: max17042_dev_init ...
<4>board-3621_evt1a.c: max17042_dev_init > Init max17042 irq pin 100 !
<4>max17042 GPIO pin read 1
<4>Enabling backlight PWM for LCD
<6> wl127x_vio_leakage_fix
<6>hw-breakpoint: debug architecture 0x4 unsupported.
<6>OMAP DMA hardware revision 5.0
<6>bio: create slab <bio-0> at 0
<6>print_constraints: vdd_lcdtp: 3300 mV normal
<6>print_constraints: vwl1271: 1800 mV
<4>i2c-core: driver [twl] using legacy suspend method
<4>i2c-core: driver [twl] using legacy resume method
<5>SCSI subsystem initialized
<6>usbcore: registered new interface driver usbfs
<6>usbcore: registered new interface driver hub
<6>usbcore: registered new device driver usb
<6>omap_i2c omap_i2c.1: bus 1 rev4.0 at 100 kHz
<6>twl4030: PIH (irq 7) chaining IRQs 368..375
<6>twl4030: power (irq 373) chaining IRQs 376..383
<6>twl4030: gpio (irq 368) chaining IRQs 384..401
<4>******IN boxer_twl_gpio_setup********
<6>print_constraints: VMMC2: 1850 mV normal standby
<6>print_constraints: VUSB1V5: 1500 mV normal standby
<6>print_constraints: VUSB1V8: 1800 mV normal standby
<6>print_constraints: VUSB3V1: 3100 mV normal standby
<7>twl4030_usb twl4030_usb: USB_DTCT_CTRL=04
<7>twl4030_usb twl4030_usb: HW_CONDITIONS 0xf0/240; link 1
<6>twl4030_usb twl4030_usb: Initialized TWL4030 USB module
<6>print_constraints: VMMC1: 1850 <--> 3150 mV at 3000 mV normal standby
<6>print_constraints: VDAC: 1800 mV normal standby
<6>omap_i2c omap_i2c.2: bus 2 rev4.0 at 400 kHz
<6>Advanced Linux Sound Architecture Driver Version 1.0.24.
<6>Sangoma WANPIPE Router v1.1 (c) 1995-2000 Sangoma Technologies Inc.
<6>Bluetooth: Core ver 2.16
<6>NET: Registered protocol family 31
<6>Bluetooth: HCI device and connection manager initialized
<6>Bluetooth: HCI socket layer initialized
<6>Bluetooth: L2CAP socket layer initialized
<6>Bluetooth: SCO socket layer initialized
<6>Switching to clocksource 32k_counter
<6>Switched to NOHz mode on CPU #0
<6>musb-hdrc: version 6.0, musb-dma, otg (peripheral+host)
<7>musb-hdrc: ConfigData=0xde (UTMI-8, dyn FIFOs, bulk combine, bulk split, HB-ISO Rx, HB-ISO Tx, SoftConn)
<7>musb-hdrc: MHDRC RTL version 1.800
<7>musb-hdrc: setup fifo_mode 4
<7>musb-hdrc: 28/31 max ep, 16384/16384 memory
<6>musb-hdrc musb-hdrc: USB OTG mode controller at fa0ab000 using DMA, IRQ 92
<6>NET: Registered protocol family 2
<6>IP route cache hash table entries: 4096 (order: 2, 16384 bytes)
<6>TCP established hash table entries: 16384 (order: 5, 131072 bytes)
<6>TCP bind hash table entries: 16384 (order: 4, 65536 bytes)
<6>TCP: Hash tables configured (established 16384 bind 16384)
<6>TCP reno registered
<6>UDP hash table entries: 256 (order: 0, 4096 bytes)
<6>UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
<6>NET: Registered protocol family 1
<6>RPC: Registered named UNIX socket transport module.
<6>RPC: Registered udp transport module.
<6>RPC: Registered tcp transport module.
<6>RPC: Registered tcp NFSv4.1 backchannel transport module.
<6>Trying to unpack rootfs image as initramfs...
<6>Freeing initrd memory: 204K
<6>omap_dsp_init: 600000 bytes @ 9ce00000
<4>Enabling VAUX for wifi
<6>omap-iommu omap-iommu.0: isp registered
<6>ashmem: initialized
<6>msgmni has been set to 898
<6>io scheduler noop registered
<6>io scheduler deadline registered
<6>io scheduler cfq registered (default)
<6>io scheduler bfq registered
<6>OMAP DSS rev 2.0
<4>Enabling power for LCD
<4>spi_probe mode : 0, per_word 16, chip_select 0, speed 375000, master_bus 4,master_cs 1
<6>omap_uart.0: ttyO0 at MMIO 0x4806a000 (irq = 72) is a OMAP UART0
<6>console [ttyO0] enabled
<6>omap_uart.1: ttyO1 at MMIO 0x4806c000 (irq = 73) is a OMAP UART1
<6>omap_uart.2: ttyO2 at MMIO 0x49020000 (irq = 74) is a OMAP UART2
<6>omap_uart.3: ttyO3 at MMIO 0x49042000 (irq = 80) is a OMAP UART3
<6>omap_ion_probe: adding heap omap3_carveout of type 2 with 9df00000@1e00000
<7>twl4030_usb twl4030_usb: twl4030_phy_suspend
<6>brd: module loaded
<6>loop: module loaded
<6>(stk) :sysfs entries created
<6>(stk) : debugfs entries created
<6>PPP generic driver version 2.4.2
<6>PPP Deflate Compression module registered
<6>PPP BSD Compression module registered
<6>PPP MPPE Compression module registered
<6>NET: Registered protocol family 24
<6>tun: Universal TUN/TAP device driver, 1.6
<6>tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
<6>Initializing USB Mass Storage driver...
<6>usbcore: registered new interface driver usb-storage
<6>USB Mass Storage support registered.
<6>usbcore: registered new interface driver usbserial
<6>usbserial: USB Serial Driver core
<7>twl4030_usb twl4030_usb: USB_DTCT_CTRL=04
<7>twl4030_usb twl4030_usb: HW_CONDITIONS 0xf0/240; link 1
<7>twl4030_usb twl4030_usb: twl4030_phy_resume
<6>android_usb gadget: Mass Storage Function, version: 2009/09/11
<6>android_usb gadget: Number of LUNs=2
<6> lun0: LUN: removable file: (no medium)
<6> lun1: LUN: removable file: (no medium)
<4>max8903_charger_enable: dtct_status 0x04
<6>android_usb gadget: android_usb ready
<6>musb-hdrc musb-hdrc: MUSB HDRC host driver
<7>drivers/usb/core/inode.c: creating file 'devices'
<7>drivers/usb/core/inode.c: creating file '001'
<6>musb-hdrc musb-hdrc: new USB bus registered, assigned bus number 1
<7>usb usb1: default language 0x0409
<7>usb usb1: udev 1, busnum 1, minor = 0
<6>usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
<6>usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
<6>usb usb1: Product: MUSB HDRC host driver
<6>usb usb1: Manufacturer: Linux 3.0.8+ musb-hcd
<6>usb usb1: SerialNumber: musb-hdrc
<7>usb usb1: usb_probe_device
<7>usb usb1: configuration #1 chosen from 1 choice
<7>usb usb1: adding 1-0:1.0 (config #1, interface 0)
<7>hub 1-0:1.0: usb_probe_interface
<7>hub 1-0:1.0: usb_probe_interface - got id
<6>hub 1-0:1.0: USB hub found
<6>hub 1-0:1.0: 1 port detected
<7>hub 1-0:1.0: standalone hub
<7>hub 1-0:1.0: individual port power switching
<7>hub 1-0:1.0: no over-current protection
<7>hub 1-0:1.0: Single TT
<7>hub 1-0:1.0: TT requires at most 8 FS bit times (666 ns)
<7>hub 1-0:1.0: power on to power good time: 10ms
<7>hub 1-0:1.0: 100mA bus power budget for each child
<7>hub 1-0:1.0: local power source is good
<7>hub 1-0:1.0: enabling power on all ports
<7>drivers/usb/core/inode.c: creating file '001'
<6>input: gpio-keys as /devices/platform/gpio-keys/input/input0
<6>input: twl4030-keypad as /devices/platform/omap/omap_i2c.1/i2c-1/1-004a/twl4030_keypad/input/input1
<6>cyttsp_init:Cypress TrueTouch(R) Standard Product
<6>cyttsp_init:I2C Touchscreen Driver (Built Oct 17 2012 @ 13:40:29)
<7>hub 1-0:1.0: state 7 ports 1 chg 0000 evt 0000
<7>hub 1-0:1.0: hub_suspend
<7>usb usb1: bus auto-suspend
<4>cyttsp:Reseting TMA340
<4>cyttsp:Start Probe 1.2
<4>
<4>cyttsp::found BL, Overriding maxx & maxy
<6>cyttsp_initialize:cyttsp-i2c: Register input device
<6>input: cyttsp-i2c as /devices/platform/omap/omap_i2c.2/i2c-2/2-0022/input/input2
<6>cyttsp_initialize:Setting up interrupt 259
<6>cyttsp_initialize:cyttsp_initialize:  Create sysfs_group successfully!
<4>cyttsp:Start Probe PASS
<6>ft5x06_init() - FT I2C Touchscreen Driver (Built Oct 17 2012 @ 13:40:30)
<3>can't get ft5x06 xreset GPIO
<6>cyttsp_power_on:BL101: f=00 s=11 err=D0 bl=010B bld=010B R=16
<6>cyttsp_power_on:BL102: tver=1100 a_id=AA1D aver=0006
<6>cyttsp_power_on:BL103: c_id=C0C1C2
<6>kxtf9 1-000f: WHO_AM_I = 0x01
<6>input: kxtf9_accel as /devices/virtual/input/input3
<6>using rtc device, twl_rtc, for alarms
<6>twl_rtc twl_rtc: rtc core: registered twl_rtc as rtc0
<4>twl_rtc twl_rtc: Cannot enable wakeup for IRQ 379
<6>i2c /dev entries driver
<6>Linux video capture interface: v2.00
<6>omap3isp omap3isp: Revision 15.0 found
<6>omap-iommu omap-iommu.0: isp: version 1.1
<7>Saving csi2 context
<7>Restoring csi2 context
<7>Saving csi2 context
<6>usbcore: registered new interface driver uvcvideo
<6>USB Video Class driver (v1.1.0)
<6>Driver for 1-wire Dallas network protocol.
<6>omap_hdq omap_hdq.0: OMAP HDQ Hardware Rev 0.5. Driver in Interrupt mode
<6>cyttsp_power_on:SI102: tver=1100 a_id=AA1D aver=0006
<6>cyttsp_power_on:SI103: c_id=C0C1C2
<6>w1_master_driver w1 bus master: Family 1 for 01.000000000000.3d is not registered.
<4>max17042: max17042_init ...
<4>max17042: max17042_probe ...
<4>max17042: next history save at 4294936954
<4>max17042: max17042_probe > IRQ is 260
<4>max17042 GPIO pin read 1
<4>max17042: max17042_device_power_on ...
<4>max17042: max17042_hw_init ...
<4>max17042:  BATTERY      Detected!
<4>config = 0x2214
<4>Valert = 0xff9b
<4>Salert = 0xff05
<4>config = 0x2214
<4>config = 0x2214
<4>shdntimer = 0x0002
<4>max17042: max17042_verify ...
<6>max17042 1-0036: Version = 0x0092
<6>max17042 1-0036: support ver. 1.0.0 enabled
<4>i2c-core: driver [max17042] using legacy suspend method
<4>i2c-core: driver [max17042] using legacy resume method
<4>MAXIM 8903 Charger registering!
<4>MAXIM 8903 Charger Initializing...
<4>MAXIM8903: Request CHARGER FLT IRQ successfully!
<4>max8903_charger_enable: B&N USB  CHARGER(500mA) Detected!
<4>MAX8903: Charging is now enabled!
<6>OMAP Watchdog Timer Rev 0x31: initial timeout 60 sec
<6>device-mapper: ioctl: 4.20.0-ioctl (2011-02-02) initialised: dm-devel@redhat.com
<6>Bluetooth: Bluetooth Driver for TI WiLink - Version 1.0
<6>(stc): st_register(2)
<6>(stc):  chnl_id list empty :2
<6>cpuidle: using governor ladder
<6>cpuidle: using governor menu
<6>(stk) : st_kim_start
<6>omap_pwm_led omap_pwm_led.0: OMAP PWM LED (lcd-backlight) at GP timer 8/0
<7>Registered led device: lcd-backlight
<6>usbcore: registered new interface driver usbhid
<6>usbhid: USB HID core driver
<6>logger: created 256K log 'log_main'
<6>logger: created 256K log 'log_events'
<6>logger: created 256K log 'log_radio'
<6>logger: created 256K log 'log_system'
<6>DSP Bridge driver loaded
<6>usbcore: registered new interface driver snd-usb-audio
<6>mmc0: new high speed MMC card at address 0001
<6>mmcblk0: mmc0:0001 SEM08G 7.39 GiB
<6>mmcblk0boot0: mmc0:0001 SEM08G partition 1 1.00 MiB
<6>mmcblk0boot1: mmc0:0001 SEM08G partition 2 1.00 MiB
<4>omap3epd-sound: Audio SoC init +
<6>(stk) :ldisc_install = 1
<6> mmcblk0: p1 p2 p3 p4 < p5 p6 p7 p8 >
<6> mmcblk0boot1: unknown partition table
<6> mmcblk0boot0: unknown partition table
<4>mmc1: host does not support reading read-only switch. assuming write-enable.
<6>mmc1: new high speed SDHC card at address c552
<6>mmcblk1: mmc1:c552 SD08G 7.42 GiB
<6> mmcblk1:
<6>Completed adding dapm widgets size = 22
<6>Completed adding DAPM routes = 21
<6>widgets updated
<6>asoc: tlv320aic31xx-dai <-> omap-mcbsp-dai.1 mapping ok
<4>sys_ck = 26000000
<4>clkout2_src_ck = 26000000
<4>sys_clkout2 = 13000000
<4>omap3epd-sound: Audio SoC init -
<6>ALSA device list:
<6>  #0: OMAP3 EDP(tlv320aic31xx)
<6>oprofile: hardware counters not available
<6>oprofile: using timer interrupt.
<6>Netfilter messages via NETLINK v0.30.
<6>nf_conntrack version 0.5.0 (7189 buckets, 28756 max)
<6>ctnetlink v0.93: registering with nfnetlink.
<6>NF_TPROXY: Transparent proxy support initialized, version 4.1.0
<6>NF_TPROXY: Copyright (c) 2006-2007 BalaBit IT Ltd.
<6>xt_time: kernel timezone is -0000
<6>ip_tables: (C) 2000-2006 Netfilter Core Team
<6>arp_tables: (C) 2002 David S. Miller
<6>TCP cubic registered
<6>Initializing XFRM netlink socket
<6>NET: Registered protocol family 10
<6>Mobile IPv6
<6>ip6_tables: (C) 2000-2006 Netfilter Core Team
<6>IPv6 over IPv4 tunneling driver
<6>NET: Registered protocol family 17
<6>NET: Registered protocol family 15
<6>Bluetooth: RFCOMM TTY layer initialized
<6>Bluetooth: RFCOMM socket layer initialized
<6>Bluetooth: RFCOMM ver 1.11
<6>Bluetooth: BNEP (Ethernet Emulation) ver 1.3
<6>Bluetooth: BNEP filters: protocol multicast
<6>Bluetooth: HIDP (Human Interface Emulation) ver 1.2
<6>lib80211: common routines for IEEE802.11 drivers
<7>lib80211_crypt: registered algorithm 'NULL'
<5>Registering the dns_resolver key type
<6>VFP support v0.3: implementor 41 architecture 3 part 30 variant c rev 3
<6>ThumbEE CPU extension supported.
<6>smartreflex smartreflex.0: omap_sr_probe: SmartReflex driver initialized
<6>smartreflex smartreflex.1: omap_sr_probe: SmartReflex driver initialized
<6>SmartReflex class 1.5 driver: initialized (86400000ms)
<6>cpufreq_interactive_input_connect: connect to cyttsp-i2c
<4>omap3_idle_init: core off state C7 disabled due to i583
<6>clock: disabling unused clocks to save power
<6>cannot apply mgr(tv) on inactive device
<4>omapfb omapfb: failed to apply dispc config
<3>omapdss DSI error: Requested pixel clock not possible with the current OMAP2_DSS_MIN_FCK_PER_PCK setting. Turning the constraint off.
<6>twl_rtc twl_rtc: setting system clock to 2000-04-22 19:19:18 UTC (956431158)
<7>Restoring csi2 context
<6>omap3 omap3isp CSI memvs initted
<7>Saving csi2 context
<6>Freeing init memory: 208K
<3>init: could not import file '/system/etc/init.local.rc' from '/init.rc'
<4>init (1): /proc/1/oom_adj is deprecated, please use /proc/1/oom_score_adj instead.
<3>init: cannot open '/initlogo.rle'
<3>init: using deprecated syntax for specifying property 'ro.serialno', use ${name} instead
<6>EXT4-fs (mmcblk0p5): mounted filesystem with ordered data mode. Opts: barrier=1
<3>(stk) :ldisc installation timeout
<6>(stk) :ldisc_install = 0
<6>EXT4-fs (mmcblk0p6): recovery complete
<6>EXT4-fs (mmcblk0p6): mounted filesystem with ordered data mode. Opts: noauto_da_alloc
<6>EXT4-fs (mmcblk0p7): recovery complete
<6>EXT4-fs (mmcblk0p7): mounted filesystem with ordered data mode. Opts: barrier=1
<6>Compat-wireless backport release: ol_R5.SP3.01
<6>Backport based on wl12xx.git ol_R5.SP3.01
<6>cfg80211: Calling CRDA to update world regulatory domain
<6>wl12xx: driver version:
<6>wl12xx: compilation time: Tue Oct 16 02:19:52 2012
<4>omap3_pm_off_mode_enable: Core OFF disabled due to errata i583
<6>sr_class1p5_calib_work: core: Calibration complete: Voltage Nominal=1200000Calib=1012500 margin=0
<3>init: cannot find '/system/bin/rild', disabling 'ril-daemon'
<3>init: using deprecated syntax for specifying property 'ro.product.manufacturer', use ${name} instead
<3>init: using deprecated syntax for specifying property 'ro.product.model', use ${name} instead
<3>android_usb: already disabled
<3>init: using deprecated syntax for specifying property 'ro.product.manufacturer', use ${name} instead
<3>init: using deprecated syntax for specifying property 'ro.product.model', use ${name} instead
<3>init: using deprecated syntax for specifying property 'ro.serialno', use ${name} instead
<3>android_usb: already disabled
<6>adb_open
<6>mtp_bind_config
<6>adb_bind_config
<6>android_work: sent uevent USB_STATE=CONNECTED
<6>android_work: sent uevent USB_STATE=DISCONNECTED
<6>proc_load: Processor Loaded /system/lib/dsp/baseimage.dof
<6>android_usb gadget: high speed config #1: android
<6>android_work: sent uevent USB_STATE=CONNECTED
<6>proc_start: dsp in running state
<6>android_work: sent uevent USB_STATE=CONFIGURED
<3>procwrap_detach: deprecated dspbridge ioctl
<3>(stk) : timed out waiting for ldisc to be un-installed
<6>(stk) :ldisc_install = 1
<3>(stk) :ldisc installation timeout
<6>(stk) :ldisc_install = 0
<3>(stk) : timed out waiting for ldisc to be un-installed
<6>(stk) :ldisc_install = 1
<3>(stk) :ldisc installation timeout
<6>(stk) :ldisc_install = 0
<3>(stk) : timed out waiting for ldisc to be un-installed
<6>(stk) :ldisc_install = 1
<3>(stk) :ldisc installation timeout
<6>(stk) :ldisc_install = 0
<6>warning: `zygote' uses 32-bit capabilities (legacy support in use)
<3>(stk) : timed out waiting for ldisc to be un-installed
<6>(stk) :ldisc_install = 1
<3>(stk) :ldisc installation timeout
<6>(stk) :ldisc_install = 0
<3>(stk) : timed out waiting for ldisc to be un-installed
<6>(stk) :ldisc_install = 1
<3>(stk) :ldisc installation timeout
<6>(stk) :ldisc_install = 0
<3>(stk) : timed out waiting for ldisc to be un-installed
<3>Bluetooth: st_register failed -22
<3>init: no such service 'hciattach'
<6>(stc): st_register(2)
<6>(stc):  chnl_id list empty :2
<6>(stk) : st_kim_start
<6>(stk) :ldisc_install = 1
<6>acc_open
<6>acc_release
<3>(stk) :ldisc installation timeout
<6>(stk) :ldisc_install = 0
<7>usb usb1: usb auto-resume
<7>hub 1-0:1.0: hub_resume
<7>hub 1-0:1.0: state 7 ports 1 chg 0000 evt 0000
<7>hub 1-0:1.0: hub_suspend
<7>usb usb1: bus auto-suspend
<3>(stk) : timed out waiting for ldisc to be un-installed
<6>(stk) :ldisc_install = 1
<6>mtp_open
<3>(stk) :ldisc installation timeout
<6>(stk) :ldisc_install = 0
<3>(stk) : timed out waiting for ldisc to be un-installed
<6>(stk) :ldisc_install = 1
<3>(stk) :ldisc installation timeout
<6>(stk) :ldisc_install = 0
<3>(stk) : timed out waiting for ldisc to be un-installed
<6>(stk) :ldisc_install = 1
<4>sr_class1p5_calib_work: core Stop sampling: Voltage Nominal=1000000 samples=17
<6>sr_class1p5_calib_work: core: Calibration complete: Voltage Nominal=1000000Calib=900000 margin=0
<3>(stk) :ldisc installation timeout
<6>(stk) :ldisc_install = 0
<3>(stk) : timed out waiting for ldisc to be un-installed
<3>init: sys_prop: permission denied uid:1003  name:service.bootanim.exit
<6>(stk) :ldisc_install = 1
<3>(stk) :ldisc installation timeout
<6>(stk) :ldisc_install = 0
<3>(stk) : timed out waiting for ldisc to be un-installed
<6>(stk) :ldisc_install = 1
<3>(stk) :ldisc installation timeout
<6>(stk) :ldisc_install = 0
<3>(stk) : timed out waiting for ldisc to be un-installed
<3>Bluetooth: st_register failed -22
<6>(stc): st_register(2)
<6>(stc):  chnl_id list empty :2
<6>(stk) : st_kim_start
<6>(stk) :ldisc_install = 1
<3>(stk) :ldisc installation timeout
<6>(stk) :ldisc_install = 0
<3>(stk) : timed out waiting for ldisc to be un-installed
<6>(stk) :ldisc_install = 1
<3>(stk) :ldisc installation timeout
<6>(stk) :ldisc_install = 0
<3>(stk) : timed out waiting for ldisc to be un-installed
<6>(stk) :ldisc_install = 1
<3>(stk) :ldisc installation timeout
<6>(stk) :ldisc_install = 0
<3>(stk) : timed out waiting for ldisc to be un-installed
<6>(stk) :ldisc_install = 1
<3>(stk) :ldisc installation timeout
<6>(stk) :ldisc_install = 0
<3>(stk) : timed out waiting for ldisc to be un-installed
<6>(stk) :ldisc_install = 1
<3>(stk) :ldisc installation timeout
<6>(stk) :ldisc_install = 0
<3>(stk) : timed out waiting for ldisc to be un-installed
<6>(stk) :ldisc_install = 1
<3>(stk) :ldisc installation timeout
<6>(stk) :ldisc_install = 0
<3>(stk) : timed out waiting for ldisc to be un-installed
<3>Bluetooth: st_register failed -22
<6>(stc): st_register(2)
<6>(stc):  chnl_id list empty :2
<6>(stk) : st_kim_start
<6>(stk) :ldisc_install = 1
<3>(stk) :ldisc installation timeout
<6>(stk) :ldisc_install = 0
<3>(stk) : timed out waiting for ldisc to be un-installed
<6>(stk) :ldisc_install = 1
<3>(stk) :ldisc installation timeout
<6>(stk) :ldisc_install = 0
<3>(stk) : timed out waiting for ldisc to be un-installed
<6>(stk) :ldisc_install = 1
<3>(stk) :ldisc installation timeout
<6>(stk) :ldisc_install = 0
<6>kxtf9 1-000f: IRQ TILT [8]
<3>(stk) : timed out waiting for ldisc to be un-installed
<6>(stk) :ldisc_install = 1
<6>DMA synchronization event drop occurred with device 33
<3>(stk) :ldisc installation timeout
<6>(stk) :ldisc_install = 0
<3>(stk) : timed out waiting for ldisc to be un-installed
<6>(stk) :ldisc_install = 1
<3>(stk) :ldisc installation timeout
<6>(stk) :ldisc_install = 0
<3>(stk) : timed out waiting for ldisc to be un-installed
<6>(stk) :ldisc_install = 1
<3>(stk) :ldisc installation timeout
<6>(stk) :ldisc_install = 0
<6>kxtf9 1-000f: IRQ TILT [1]
<3>(stk) : timed out waiting for ldisc to be un-installed
<3>Bluetooth: st_register failed -22
<6>(stc): st_register(2)
<6>(stc):  chnl_id list empty :2
<6>(stk) : st_kim_start
<6>(stk) :ldisc_install = 1
<6>kxtf9 1-000f: IRQ TAP2 [1]