U-Boot 2009.08 (Jul 05 7:27)

CPU:   Freescale i.MX 6 fat 792 MHz
Temperature:   can't get valid data!
mx6q pll1: 792MHz
m8MHz
mx6q pll3: 480MHz
mx6q pll8: 50MHz
ipg clock     : 66000000Hz
ipg per clock : 66000 clock    : 80000000Hz
cspi clock    : 60000000Hz
ahb clock     : 132000000Hz
axi clock   : 264000000Hz
emi_slow clock: 29333333Hz
ddr clock     : 528000000Hz
usdhc1 clock  : 200000000Hz
usdhc2 clock Hz
usdhc3 clock  : 200000000Hz
usdhc4 clock  : 200000000Hz
nfc clock     : 24ard: MX6Q-SABRELITE:[ POR]
Boot Device: I2C
I2C:   ready
DRAM:   1 GB
MMC:   FSL_USDHC: 0,FSLJEDEC ID: 0xbf:0x25:0x41
Reading SPI NOR flash 0xc0000 [0x2000 bytes] -> ram 0x276009b8
SUCCESS

In:    serial
Out:   serial
Err:   serial
Net:   got MAC address from:b8:00:fd:4e
FEC0 [PRIME]
Warning: FEC0 MAC addresses don't match:
Address in SROM is         00:19:b8:00:fd:4e
Address in environment is  00:01:02:03:04:05

Hit any key to stop autoboot:  0
m is current device
reading /6q_bootscript

** Unable to read "/6q_bootscript" from mmc 0:1 **
Loading file "/6q_bootscript" from mmc devi583 bytes read
## Executing script at 10008000
Loading file "/boot/uImage" from mmc device 0:1 (xxa1)
3605880 bytes ## Booting kernel from Legacy Image at 10800000 ...
   Image Name:   Linux-3.0.15-01386-g5c661b1
   Image Type:   ARM Linux Kernel Image (uncompressed)
   Data Size:    3605816 Bytes =  3.4 MB
   Load Address: 10008000
   Entry Point:  10008000
   Verifying Checksum ... mage ... OK
OK

Snel ...

Uncompressing Linux...done, booting the kernel.
Lion 3.0.15-01386-g5c661b1 (ericn@ericsony) (gcc version 4.4.4 (4.4.4_09.06.2010) ) #64 SMP PREEMPT Tue Jun 26 11:16:43 MST 2012
CPU: ARMv7 Processor [412fc09a] revision 10 (ARMv7), cr=10c53c7d
CPU: VIPT nonaliasing data cache, VIPT aliasing instruction cache
Machine: Freescale i.MX 6Quad Sabre-Lite Board
Memory policy: ECC disabled, Data cache writealloc
PERCPU: Embedded 7 pages/cpu @8c008000 s5440 r8192 d15040 u32768
Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 227328
Kernel command line: console=ttymxc1,115200 vmalloc=400M root=/dev/mmcblk0p1 rootwait fixrtc consoleblank=0 video=mxcfb0:dev=hdmi,1280x720M@60,if=RGB24 video=mxcfb1:dev=lcd,800x480M@60,if=RGB666 fbmem=28M,10M
PID hash table entries: 4096 (order: 2, 16384 bytes)
Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
Memory: 640MB 256MB = 896MB total
nel memory layout:able, 150812k reserved, 0K highmem
    vector  :  0xffff1000   (   4 kBp  : 0xfff00000 - 0xfffe0000   ( 896 kB)
    f4600000 -   ( 184 MB)
    vmalloc : 0xc0800000 - 0xf2000000   ( 792 MB)
    lowmem  : 0x80000000 - 0xc0000000   (1024 MB)
    pkmap   : 0x7fe00000 - 0x80000000   (   2 MB)
    modules : 0x7f000000 - 0x7fe00000   (  14 MB)
      .init : 0x80008000 - 0x80035000   ( 180 kB)
      .text : 0x80035000 - 0x809eba64   (9947 kB)
      .data : 0x809ec000 - 0x80a2f0a0   ( 269 kB)
       .bss : 0x80a2f0c4 - 0x80a59e78   ( 172 kB)
SLUB: Genslabs=13, HWalign=32, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
Preemptible hierarchical RCU implementation.
NR_IRQS:496
MXC GPIO hardware
sched_clock: 32 bits at 6MHz, resolution 166ns, wraps every 715827ms
MXC_Early serial console at MMIO 0x21e8000 (options '115200')
bootconsole [ttymxc1] enabled
Console: colour dummy device 80x30
Calibrating delay loop... 1581.05 BogoMIPS (lpj=7905280)
pid_max: d68 minimum: 301
Mou-cache hash table entries: 512
e buffer coherency: ok
hw perfMv7 Cortex-A9 PMU driver, 7 counters available
CBooted secondary processor
CPU2: Booted seconor
CPU3: Booted secondary processup 4 CPUs
SMP: Total of 4 processors activated (6324.22 BogoMIPS).
print_constraints: dummy:
NET: Registered protocol family 16
print_constraints: vddpu: 725 <--> 1300 mV at 1100 mV fast normal
print_constraints: vddcore: 725 <--> 1300 mV at 1100 mV fast normal
print_constraints: vddsoc: 725 <--> 1300 mV at 1200 mV fast normal
print_: vdd2p5: 2000 <--> 2775 mV at 2400 mV fast normal
print_constraints: vdd1p1: 800 <--> 1400 mV at t normal
straints: vdd3p0: 2800 <--> 3150 mV at 3000 mV fast normal
------------ Board type Sabre Lite
hw-breakpoint: found 6 breakpoint and 1 watchpoint registers.
hw-brebreakpoint(s) reserved for watchpoint single-step.
hw-brximum watchpoint size is 4 bytes.
 controller enabled
l2, CACHE_ID 0x410000c7, AUX_CTRL 0x02070000, Cache size: 1048576 B
 usb wakeup probe
IMX usb wakeup probe
bio: create slab <bio-0> at 0
print_constraints: VDDA: 2500 mV
print_constraints: VDDIO: 3300 mV
machints_voltage: VDDD: unsupportable voltage constraints
rtage reg-fixed-voltage.2: Failed to register regulator: -22
reg-fixprobe of reg-fixed-voltage.2 failed with error -22
prits: vmmc: 3300 mV
SCSI subsystem initialized
spi_imx imx6q-ecspi.0: probed
usbcore: registered new interface driver usbfs
usbcored new interface drivered new device driver usb
Freescale USB OTG Driver loaded, $Revision: 1.55 $
p source irq 75
imx-ipuv3 imx-ipuv3.0: IPU DMFC NORMAL mode: 1(0~1), 5B(4,5), 5F(6,7)
imx-ipuv3 imx-ipuv3.1: IPU DMFC NORMAL mode: 1(0~1), 5B(4,5), 5F(6,7)
mxc_mipi_csi2 mxc_mipi_csi2: i.MX MIPI CSI2 driver probed
mxc_mipi_csi2 mxc_mipi_csi2: i.MX MIPI CSI2 dphy version is 0x3130302a
MIPI CSI2 driver module loaded
Advanced Linux Sound Architecture Driver Version 1.0.24.
cfg80211: Calling CRDA to update world regulatory domain
i2c-core: driver [max17135] using legacy suspend method
i2c-core: driver [max17135] using legacy resume method
Switching to clocksource mxc_timer1
Switched to NOHz mode on CPU #0
Switched to NOHz mode on CPU #2
Switched to NOHz mode on CPU #1
Switched to NOHz mode on CPU #3
NET: Registered protocol family 2
IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
h table entries: 131072 (order: 8, 1048576 bytes)
TCP bind hash table entries: 65536 (order: 7, 786432 bytes)
tables configured (established 131072 bind 65536)
TCP reed
UDP hasies: 512 (order: 2, 16384 bytes)
UDP-Lite hash table entries: 512 (384 bytes)
NET: Retocol family 1
RPC:named UNIX socket tran.
RPC: Regtransport module.
RPC: Registered tcp transport module.
RPC: Registered tcp NFSv4.1 backchannel transport module.
Static Power Management for Freescale i.MX6
cpaddr = c0884000 suspend_iram_base=c0932000
PM driver module loaded
i.MXC CPU frequency driver
Jion 2.2. (NAND) �© 2001-2006 Red Hat, Inc.
msgmni has been set to 1753
io scheduler noop registeredler deadline registered
io scheduler cfq registered (default)
MIPI DSI drivered
mxc_sdc_fb mxc_sdc_fb.0: register mxc display driver hdmi
mxc_hdmi mxc_hdmi: Detected HDMI controller 0x13:0xa:0xa0:0xc1
fbcvt: 1280x720@60: CVT Name - .921M9
imx-ipuv3 imx-ipuv3.0: IPU DMFC DP HIGH RESOLUTION: 1(0,1), 5B(2~5), 5F(6,7)
Console: switching to colour frame buffer device 160x45
mxc_sdc_fb mxc_sdc_fb.1: register mxc display driver lcd
fbcvt: 800x480@60: CVT Name - .384M9
imx-ipuv3 imx-ipuv3.0: ext di clk already in use, go back to internal clk
mxc_sdc_fb mxc_sdc_fb.2: register mxc display driver ldb
_regulator_get: get() with no identifier
mxc_sdc_fb mxc_sdc_fb.3: register mxc display driver ldb
f 1280x720@60: CVT Name - .921M9
mx-ipuv3 imx-ipuv3.0: WARNING: adapt panel end blank lines
sdma imx-sdmirmware 1.1
ix-sdma: initialized
erial: IMX driver
ttymxc0 at MMIO 0x202058) is a IMX
mx-uart.1: ttymxc1 at MMIO 0x21e8000 (irq = 59) is a IMX
 new_ufcr=b2=4027 new_ucr2=4027, old_ubir=f num=1f7, old_ubmr=15b denom=c34
clk=v=7 num=504 denom=3125 baud=115200
console console disabled
console [ttymxc1] enabled, bootconsole disabled
loop: module loadeCan't recover from RESET No sata disk.
m25p80 spi0.0: sst25vf016b (2048 Kbytes)
Creating 2 MTD partitions on "m25p80":
0x000000000000-0x000000040000er"
0x0-0x000000200000 : "kernel"
vcan: Virtual CAN interface driver
CAN device driver interface
flexcan netdevice driver
flexcan imx6q-flexcan.0: device registered (reg_base=c09a8000, irq=142)
FEC Ethernet Driver
fec_enet_mii_bus: probed
-ehci fsl-ehci.0: Freescale On-Chip EHCI Host Controllerer
fsl-ehci fsl-ehci.us registerbus number 1
fsl-ehci fsl-ehci.0: irq 75, io base 0x02184000
fsl-ehci fsl-ehci.0: USB 2.0 started, EHCI 1.00
usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb1: Product: Freescale On-Chip EHCI Host Controller
usb usb1: Manufacturer: Linux 3.0.15-01386-g5c661b1 ehci_hcd
usb usb1: SerialNumber: fsl-ehci.0
hub 1-0:1.0: USB hub found
hub 1rt detected
add wake up source irq 72
fehci.1: Freescale On-Cht Controller
fsl-ehci: new USB bud, assigned bus number 2
fsl-ehci fsl-ehci.1: irq 72, io base 0x02184200
fsl-ehci fsl-ehci.1: USB 2.0 started, EHCI 1.00
vice found, idVendor=1d6b, idProduct=0002
usb usb2: New SB device strings: Mfr=3, Product=2, SerialNumber=1
usuct: Freescaontroller
661b1 ehci_hc2: SerialNumber: fsl-ehci.1
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 1 port detected
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
ARC USBOTG Device Controller driver (1 August 2005)
mousedev: PS/2 mouse device common for all mice
input: gpio-keys as /devices/platform/gpio-keys/input/input0
tsc2004_prepare_for_reading: write_cmd -5
tsc2004: probe of 2-0048 failed with error -5
egalax_ts 2-0004: egalax_ts: failed to read firmware version
egalax_ts: probe of 2-0004 failed with error -5
i2c-core: driver [isl29023] using legacy suspend method
i2c-core: driver [isl29023] using legacy resume method
snvs_rtc snvs_rtc.0: rtc core: registered snvs_rtc as rtc0
i2c s driver
Linux video capture interface: v2.00
utput mxc_v4l2_output.0: V4L2 deved as video16
mxc_vmxc_v4l2_outpstered as video17
mut mxc_v4l2_output.0: V4L2 device registered as video18
mxc_v4l2_output mxc_v4l2_output.0: V4L2 device registered as video19
mxc_v4l2_output mxc_v4l2_output.0: V4L2 device registered as video20
mxc_v4l2_output mxc_v4lV4L2 device registered as video21
i2c- [mag3110] u suspend method
i2c-co[mag3110] usresume method
imx2wdt.0: IMX2+ Watchdog Timer enabled. timeout=60s (nowayout=1)
sdhci: Secure Digital Host Controller Interface driver
sdhci: Copyright(c) Pierre Ossman
mmcontroller version (3). You may experience problems.
mmc0: SDHCI controller on platform [sdhci-esdhc-imx.2] using ADMA
sdhci sdhci-esdhc-imx.3: no write-protect pin available!
mc1: Unknown controller version y experience problems.
mmc1: SDHCI controtform [sdhci-esdhc-imx.3] using ADMA
mxc_r Adapter(VDOA) driver VPU initialized
mxc_asrc registered
Anatop Thermal registered as thermal_zone0
usb 2-1: new high speed USB device number 2 using fsl-ehci
anatop_thermal_probe: default cooling device is cpufreq!
usbcore: registered new interface driver usbhid
usbhid: USB HID core driver
mxc_hdmi_soc mxc_hdmi_soc.0: MXC HDMI Audio
sgtl5000 0-000a: Failed to get supply 'VDDD': -19
print_constraints: 0-000a: 850 <--> 1600 mV at 1200 mV normal
sgtl5000 0-000a: sgtl5000 revision 17
mmc0: new SDHC card at address 0001
mmcblk0: mmc0:0001 00000 7.46 GiB
 mmcblk0: p1
asoc: sgtl5000 <-> imx-ssi.1 mapping ok
asoc: mxc-hdmi-soc <-> imx-hdmi-soc-dai.0 mapping ok
ALSA device list:
  #0: sgtl5000-audio
  #1: imx-hdmi-soc
NET: Registered protocol family 26
TCP cubic registered
NET: Registered protocol family 17
can: controller area network core (rev 20090105 abi 8)
NET: Registered protocol family 29
can: raw protocol (rev 20090105)
can: broadcast manager protocol (rev 20090105 t)
lib80211: common routines for IEEE802.11 drivers
VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4
usb 2-1: New USB device found, idVendor=0424, idProduct=2513
usb 2-1: New USB device strings: Mfr=0, Product=0, SerialNumber=0
Bus freq driver module loaded
mxc_dvfs_core_probe
hub 2-1:1.0: USB hub found
hub 2-1:1.0: 3 ports detected
DVFS driver module loaded
snvs_rtc snvs_rtc.0: setting system clock to 1970-01-01 00:00:00 UTC (0)
EXT3-fs: barriers not enabled
usb 2-1.2: new low speednumber 3 using fsl-ehci
u2-1.2: New USB device fdor=09da, idProduct=0260
usb 2-1.2: New USB ds: Mfr=1, Product=2, SerialNumber=1.2: Product: USB Keyboard
usb 2-1.2: Manufacturer:
input:   USB Keyboard as /devices/platform/fsl-ehci.1/usb2/2-1/2-1.2/2-1.2:1.0/input/input1
generic-usb 0003:09DA:0260.0001: input,hidraw0: USB HID v1.10 Keyboard [  USB Keyboard] on usb-fsl-ehci.1-1.2/input0
input:   USB Keyboard as /devices/platform/fsl-ehci.1/usb2/2-1/2-1.2/2-1.2:1.1/input/input2
eneric-usb 0003:09DA:0260.0002: input,hidraw1: USB HID v1.10 Device [  USB Keyboard] on usb-fsl-ehci.1-1.2/input1
 starting.  Commit interval 5 seconds
Eblk0p1): using internal journal
EXT3-fs (mmcovery complEXT3-fs (mmcblk0p1): mounted filesystem with writeback daFS: Mounted root (ext3 filesystem) on device 179:1.
Freeing init memory: 180K
Tmal: fuse data 0x58e5523a
anatop_thermal_counting_ratio: raw25c=1422 raw_hot=1362 hot_temp=58